Now that all data is transferred via the FIFO (ti_buf) there is no need to track
the source buffer being used for the data transfer. This also eliminates the
need for a separate subsection for PDMA state migration.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-30-mark.cave-ayland@ilande.co.uk>
PDMA as implemented on the Quadra 800 uses DREQ to load data into the FIFO
up to a maximum of 16 bytes at a time. The MacOS toolbox ROM requires this
because it mixes FIFO and PDMA transfers whilst checking the FIFO status
and counter registers to ensure success.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-29-mark.cave-ayland@ilande.co.uk>
Currently the target selection for PDMA is done after the SCSI command has been
delivered which is not correct. Perform target selection as part of the initial
get_cmd() call when the command is submitted: if no target is present, don't
raise DRQ.
If the target is present then switch to the command phase since the MacOS toolbox
ROM checks for this before attempting to submit the SCSI command.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-28-mark.cave-ayland@ilande.co.uk>
This better describes the purpose of the function.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-27-mark.cave-ayland@ilande.co.uk>
The cmdbuf is really just a copy of FIFO data (including extra message phase
bytes) so its pdma_origin is effectively TI. Fortunately we already know when
we are receiving a SCSI command since do_cmd == 1 which enables us to
distinguish between the two cases in esp_pdma_read()/esp_pdma_write().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-26-mark.cave-ayland@ilande.co.uk>
Real hardware simply counts down using the in-built TC to determine when the
the PDMA request is complete. Use the TC to determine the PDMA transfer length
which then enables us to remove the redundant pdma_len variable.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-25-mark.cave-ayland@ilande.co.uk>
This eliminates the last user of the PDMA-specific pdma_cur variable which can
now be removed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-24-mark.cave-ayland@ilande.co.uk>
Here the updates to async_len and ti_size are moved into the corresponding
esp_pdma_read()/esp_pdma_write() function to eliminate the reference to
pdma_cur in do_dma_pdma_cb().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-23-mark.cave-ayland@ilande.co.uk>
Now that PDMA SCSI commands are accumulated in cmdbuf in the same way as normal
commands, the existing logic for locating the start of the SCSI command in
cmdbuf via cmdlen can be used. This enables the PDMA-specific pdma_start and
also get_pdma_buf() to be removed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-22-mark.cave-ayland@ilande.co.uk>
Now that all SCSI commands are accumulated in cmdbuf, remove the buf and buflen
parameters from get_cmd() since these always reference cmdbuf and ESP_CMDBUF_SZ
respectively.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-21-mark.cave-ayland@ilande.co.uk>
Now that all SCSI commands are accumulated in cmdbuf, remove the buf parameter
from do_cmd() since this always points to cmdbuf.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-20-mark.cave-ayland@ilande.co.uk>
ESP SCSI commands are already accumulated in cmdbuf and so there is no need to
keep a separate pdma_buf buffer. Accumulate SCSI commands for PDMA transfers in
cmdbuf instead of pdma_buf so update cmdlen accordingly and change pdma_origin
for PDMA transfers to CMD which allows the PDMA origin to be removed.
This commit also removes a stray memcpy() from get_cmd() which is a no-op because
cmdlen is always zero at the start of a command.
Notionally the removal of pdma_buf from vmstate_esp_pdma also breaks migration
compatibility for the PDMA subsection until its complete removal by the end of
the series.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-19-mark.cave-ayland@ilande.co.uk>
This is the first step in removing get_pdma_buf() from esp.c.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-17-mark.cave-ayland@ilande.co.uk>
The limiting of DMA transfers to the maximum size of the available data is already
handled by esp_do_dma() and do_dma_pdma_cb().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-15-mark.cave-ayland@ilande.co.uk>
The ESP device already keeps track of the remaining bytes left to transfer via
its TC (transfer counter) register which is decremented for each byte that
is transferred across the SCSI bus.
Switch the transfer logic to use the value of TC instead of dma_left and then
remove dma_left completely, adding logic to the vmstate_esp post_load() function
to transfer the old dma_left value to the TC register during migration from
older versions.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-14-mark.cave-ayland@ilande.co.uk>
The value of dma_counter is set once at the start of the transfer and remains
the same until the transfer is complete. This allows the check in esp_transfer_data
to be simplified since dma_left will always be non-zero until the transfer is
completed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-13-mark.cave-ayland@ilande.co.uk>
Perform the length adjustment whereby a value of 0 in the STC represents
a transfer length of 0x10000 at the point where the TC is loaded at the
start of a DMA command rather than just when a TI (Transfer Information)
command is executed. This better matches the description as given in the
datasheet.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-12-mark.cave-ayland@ilande.co.uk>
This function simplifies reading the STC register value without having to manually
shift each individual 8-bit value.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-11-mark.cave-ayland@ilande.co.uk>
These functions simplify reading and writing the TC register value without having to
manually shift each individual 8-bit value.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-10-mark.cave-ayland@ilande.co.uk>
The transfer direction is currently determined by checking the sign of ti_size
but as this series progresses ti_size can be zero at the end of the transfer.
Use the SCSI phase to determine the transfer direction as used in other SCSI
controller implementations.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-9-mark.cave-ayland@ilande.co.uk>
This will become more useful later when trying to debug mixed FIFO and PDMA
requests.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-8-mark.cave-ayland@ilande.co.uk>
Move the trace event to the end of the function so that it correctly reports
the returned value if it doesn't come directly from the rregs array.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-7-mark.cave-ayland@ilande.co.uk>
This enables us to determine whether the command being issued is for a DMA or a
non-DMA transfer.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-6-mark.cave-ayland@ilande.co.uk>
The QOM object representing ESPState is currently embedded within both the
SYSBUS_ESP and PCI_ESP devices with migration state handled by embedding
vmstate_esp within each device using VMSTATE_STRUCT.
Since the vmstate_esp fields are embedded directly within the migration
stream, the incoming vmstate_esp version_id is lost. The only version information
available is that from vmstate_sysbus_esp_scsi and vmstate_esp_pci_scsi, but
those versions represent their respective devices and not that of the underlying
ESPState.
Resolve this by adding a new version-dependent field in vmstate_sysbus_esp_scsi
and vmstate_esp_pci_scsi which stores the vmstate_esp version_id field within
ESPState to be used to allow migration from older QEMU versions.
Finally bump the vmstate_esp version to 5 to cover the upcoming ESPState changes
within this patch series.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-5-mark.cave-ayland@ilande.co.uk>
Make this new QOM device state a child device of both the sysbus-esp and esp-pci
implementations.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-4-mark.cave-ayland@ilande.co.uk>
The existing ESP QOM type currently represents a sysbus device with an embedded
ESP state. Rename the type to SYSBUS_ESP accordingly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-3-mark.cave-ayland@ilande.co.uk>
The command complete callback has a SCSIRequest as the first argument,
and the status field of that structure is identical to the 'status'
argument. So drop the argument from the callback.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Message-Id: <20201116184041.60465-3-hare@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Right now, recoverable sense values are only passed directly to the
guest only for rerror=report. However, when rerror/werror are 'stop'
we still don't want the host to be involved on every UNIT ATTENTION
(especially considered that the QMP event will not have enough information
to act on the report).
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Instead of fishing it from *r->status, just pass the SCSI status
as a positive value of the second parameter and an errno as a
negative value.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The new function is an extension of the switch statement in scsi-disk.c
which also includes the errno cases only found in sg_io_sense_from_errno.
This allows us to consolidate the errno handling.
Extracted from a patch by Hannes Reinecke <hare@suse.de>.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When requested to ignore errors, just do nothing and let the
request complete normally. This means that the request will
be accounted correctly.
This is what commit 40dce4ee61 ("scsi-disk: fix rerror/werror=ignore",
2018-10-19) was supposed to do:
Fixes: 40dce4ee61 ("scsi-disk: fix rerror/werror=ignore", 2018-10-19)
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If virtio_scsi_dataplane_start fails, there is a small window when it drops the
aio lock (in aio_wait_bh_oneshot) and the dataplane's AIO handler can
still run during that window.
This is done after the dataplane was marked as fenced, thus we use this flag
to avoid it doing any IO.
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20201217150040.906961-2-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
'enospc' is the default for -drive, but qemu allows user to set
drive option werror. If werror of scsi-generic is set to 'report'
by user, qemu will not allow vm to start.
This patch allow user to set werror as 'report' for scsi-generic.
Signed-off-by: Zihao Chang <changzihao1@huawei.com>
Reviewed-by: Fam Zheng <fam@euphon.net>
Message-Id: <20201103061240.1364-1-changzihao1@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add tracepoints for SG_IO commands to allow for debugging
of SG_IO commands.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Message-Id: <20201116183114.55703-4-hare@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The current code sets an infinite timeout on SG_IO requests,
causing the guest to stall if the host experiences a frame
loss.
This patch adds an 'io_timeout' parameter for SCSIDevice to
make the SG_IO timeout configurable, and also shortens the
default timeout to 30 seconds to avoid infinite stalls.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Message-Id: <20201116183114.55703-3-hare@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Count number of queues that we initialized and only deinitialize these that we
initialized successfully.
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20201217150040.906961-3-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently, blk_is_read_only() tells whether a given BlockBackend can
only be used in read-only mode because its root node is read-only. Some
callers actually try to answer a slightly different question: Is the
BlockBackend configured to be writable, by taking write permissions on
the root node?
This can differ, for example, for CD-ROM devices which don't take write
permissions, but may be backed by a writable image file. scsi-cd allows
write requests to the drive if blk_is_read_only() returns false.
However, the write request will immediately run into an assertion
failure because the write permission is missing.
This patch introduces separate functions for both questions.
blk_supports_write_perm() answers the question whether the block
node/image file can support writable devices, whereas blk_is_writable()
tells whether the BlockBackend is currently configured to be writable.
All calls of blk_is_read_only() are converted to one of the two new
functions.
Fixes: https://bugs.launchpad.net/bugs/1906693
Cc: qemu-stable@nongnu.org
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20210118123448.307825-2-kwolf@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The documentation for bdrv_set_aio_context_ignore() states this:
* The caller must own the AioContext lock for the old AioContext of bs, but it
* must not own the AioContext lock for new_context (unless new_context is the
* same as the current context of bs).
As blk_set_aio_context() makes use of this function, this rule also
applies to it.
Fix all occurrences where this rule wasn't honored.
Suggested-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Sergio Lopez <slp@redhat.com>
Message-Id: <20201214170519.223781-2-slp@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
Add trace events for virtio command and response tracing.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Message-Id: <20201116183114.55703-2-hare@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 8118f0950f "migration: Append JSON description of migration
stream" needs a JSON writer. The existing qobject_to_json() wasn't a
good fit, because it requires building a QObject to convert. Instead,
migration got its very own JSON writer, in commit 190c882ce2 "QJSON:
Add JSON writer". It tacitly limits numbers to int64_t, and strings
contents to characters that don't need escaping, unlike
qobject_to_json().
The previous commit factored the JSON writer out of qobject_to_json().
Replace migration's JSON writer by it.
Cc: Juan Quintela <quintela@redhat.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20201211171152.146877-17-armbru@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Move the property types and property macros implemented in
qdev-properties-system.c to a new qdev-properties-system.h
header.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20201211220529.2290218-16-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
There is (mostly theoretical) race between removal of a scsi device and
scsi_dma_restart_bh.
It used to be easier to hit this race prior to my / Paulo's patch series
that added rcu to scsi bus device handling code, but IMHO this race
should still be possible to hit, at least in theory.
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=1854811
Fix it anyway with a patch that was proposed by Paulo in the above bugzilla.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20201210125929.1136390-2-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Linux has some OS-specific (and sometimes weird) mappings for various SCSI
statuses and sense codes. The most important is probably RESERVATION
CONFLICT. Add them so that they can be reported back to the guest
kernel.
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There is no "version 2" of the "Lesser" General Public License.
It is either "GPL version 2.0" or "Lesser GPL version 2.1".
This patch replaces all occurrences of "Lesser GPL version 2" with
"Lesser GPL version 2.1" in comment section.
This patch contains all the files, whose maintainer I could not get
from ‘get_maintainer.pl’ script.
Signed-off-by: Chetan Pant <chetan4windows@gmail.com>
Message-Id: <20201023124424.20177-1-chetan4windows@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
[thuth: Adapted exec.c and qdev-monitor.c to new location]
Signed-off-by: Thomas Huth <thuth@redhat.com>
