When passing through an USB storage device to a pseries guest, it
is currently not possible to automatically boot from the device
if the "bootindex" property has been specified, too (e.g. when using
"-device nec-usb-xhci -device usb-host,hostbus=1,hostaddr=2,bootindex=0"
at the command line). The problem is that QEMU builds a device tree path
like "/pci@800000020000000/usb@0/usb-host@1" and passes it to SLOF
in the /chosen/qemu,boot-list property. SLOF, however, probes the
USB device, recognizes that it is a storage device and thus changes
its name to "storage", and additionally adds a child node for the
SCSI LUN, so the correct boot path in SLOF is something like
"/pci@800000020000000/usb@0/storage@1/disk@101000000000000" instead.
So when we detect an USB mass storage device with SCSI interface,
we've got to adjust the firmware boot-device path properly that
SLOF can automatically boot from the device.
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=1354177
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
stxvll: Store VSX Vector Left-justified with Length
Vector (8-bit elements) in BE/LE:
+---+---+---+---+---+---+---+---+---+---+---+---+---+---+--+--+
|“T”|“h”|“i”|“s”|“ ”|“i”|“s”|“ ”|“a”|“ ”|“T”|“E”|“S”|“T”|00|00|
+---+---+---+---+---+---+---+---+---+---+---+---+---+---+--+--+
Storing 14 bytes would result in following Little/Big-endian Storage:
+---+---+---+---+---+---+---+---+---+---+---+---+---+---+--+--+
|“T”|“h”|“i”|“s”|“ ”|“i”|“s”|“ ”|“a”|“ ”|“T”|“E”|“S”|“T”|FF|FF|
+---+---+---+---+---+---+---+---+---+---+---+---+---+---+--+--+
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
A function to check if all digits of a given BCD number is valid is
here presented because more instructions will need to reuse the
same code.
Signed-off-by: Jose Ricardo Ziviani <joserz@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The structure and corresponding defines and functions need to be used
outside of fpu_helper.c as well.
Add u8, u16, u32 and Int128 to the structure.
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The H_SIGNAL_SYS_RESET hcall allows a guest CPU to raise a system reset
exception on CPUs within the same guest -- all CPUs, all-but-self, or a
specific CPU (including self).
This has not made its way to a PAPR release yet, but we have an hcall
number assigned.
H_SIGNAL_SYS_RESET = 0x380
Syntax:
hcall(uint64 H_SIGNAL_SYS_RESET, int64 target);
Generate a system reset NMI on the threads indicated by target.
Values for target:
-1 = target all online threads including the caller
-2 = target all online threads except for the caller
All other negative values: reserved
Positive values: The thread to be targeted, obtained from the value
of the "ibm,ppc-interrupt-server#s" property of the CPU in the OF
device tree.
Semantics:
- Invalid target: return H_Parameter.
- Otherwise: Generate a system reset NMI on target thread(s),
return H_Success.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The 'cpu_version' field in PowerPCCPU is badly named. It's named after the
'cpu-version' device tree property where it is advertised, but that meaning
may not be obvious in most places it appears.
Worse, it doesn't even really correspond to that device tree property. The
property contains either the processor's PVR, or, if the CPU is running in
a compatibility mode, a special "logical PVR" representing which mode.
Rename the cpu_version field, and a number of related variables to
compat_pvr to make this clearer.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Thomas Huth <thuth@redhat.com>
The pseries machine type is a bit unusual in that it runs a paravirtualized
guest. The guest expects to interact with a hypervisor, and qemu
emulates the functions of that hypervisor directly, rather than executing
hypervisor code within the emulated system.
To implement this in TCG, we need to intercept hypercall instructions and
direct them to the machine's hypercall handlers, rather than attempting to
perform a privilege change within TCG. This is controlled by a global
hook - cpu_ppc_hypercall.
This cleanup makes the handling a little cleaner and more extensible than
a single global variable. Instead, each CPU to have hypercalls intercepted
has a pointer set to a QOM object implementing a new virtual hypervisor
interface. A method in that interface is called by TCG when it sees a
hypercall instruction. It's possible we may want to add other methods in
future.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
spapr_h_cas_compose_response() includes a cpu_update parameter which
controls whether it includes updated information on the CPUs in the device
tree fragment returned from the ibm,client-architecture-support (CAS) call.
Providing the updated information is essential when CAS has negotiated
compatibility options which require different cpu information to be
presented to the guest. However, it should be safe to provide in other
cases (it will just override the existing data in the device tree with
identical data). This simplifies the code by removing the parameter and
always providing the cpu update information.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Currently the pseries machine has two paths for constructing CPUs. On
newer machine type versions, which support cpu hotplug, it constructs
cpu core objects, which in turn construct CPU threads. For older machine
versions it individually constructs the CPU threads.
This division is going to make some future changes to the cpu construction
harder, so this patch unifies them. Now cpu core objects are always
created. This requires some updates to allow core objects to be created
without a full complement of threads (since older versions allowed a
number of cpus not a multiple of the threads-per-core). Likewise it needs
some changes to the cpu core hot/cold plug path so as not to choke on the
old machine types without hotplug support.
For good measure, we move the cpu construction to its own subfunction,
spapr_init_cpus().
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
bcdsetsgn.: Decimal set sign. This instruction copies the register
value to the result register but adjust the signal according to
the preferred sign value.
Signed-off-by: Jose Ricardo Ziviani <joserz@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
bcdcpsgn.: Decimal copy sign. Given two registers vra and vrb, it
copies the vra value with vrb sign to the result register vrt.
Signed-off-by: Jose Ricardo Ziviani <joserz@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
bcdctsq.: Decimal convert to signed quadword. It is possible to
convert packed decimal values to signed quadwords.
Signed-off-by: Jose Ricardo Ziviani <joserz@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
bcdcfsq.: Decimal convert from signed quadword. It is not possible
to convert values less than -10^31-1 or greater than 10^31-1 to be
represented in packed decimal format.
Signed-off-by: Jose Ricardo Ziviani <joserz@linux.vnet.ibm.com>
[dwg: Corrected constant which should be 10^16-1 but was 10^17-1]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
stxsd: Store VSX Scalar Dword
stxssp: Store VSX Scalar SP
Moreover, DQ-Form/DS-FORM instructions shares the same primary
opcode(0x3D). For DQ-FORM bits 29:31 are used, for DS-FORM bits 30:31
are used. Common routine to decode primary opcode(0x3D) -
ds-form/dq-form instructions is required.
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
lxsd: Load VSX Scalar Dword
lxssp: Load VSX Scalar Single
Moreover, DS-Form instructions shares the same primary opcode, bits
30:31 are used to decode the instruction. Use a common routine to decode
primary opcode(0x39) - ds-form instructions and branch-out depending on
bits 30:31.
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
- xscmpodp & xscmpudp are missing flags reset.
- In xscmpodp, VXCC should be set only if VE is 0 for signalling NaN case
and VXCC should be set by explicitly checking for quiet NaN case.
- Comparison is being done only if the operands are not NaNs. However as
per ISA, it should be done even when operands are NaNs.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Add _BIT to CRF_[GT,LT,EQ_SO] and introduce CRF_[GT,LT,EQ,SO] for usage
without shifts in the code. This would simplify the code.
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Move instruction decode helpers to target-ppc/internal.h so that some
of these can be used from outside of translate.c. This movement also
helps to get rid of some duplicate helpers from target-ppc/fpu_helper.c.
Suggested-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
ldl_p has a signed return type so assigning it to uint64_t implicitly
sign-extends the value. This results in devices with min_access_size = 8
seeing unexpected values passed to their write handlers.
Example: guest performs a 32-bit write of 0x80000000 to an mmio region
and the handler receives 0xFFFFFFFF80000000 in its value argument.
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Message-Id: <1485440557-10384-1-git-send-email-lprosek@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Turn Chardev into Object.
qemu_chr_alloc() is replaced by the qemu_chardev_new() constructor. It
will call qemu_char_open() to open/intialize the chardev with the
ChardevCommon *backend settings.
The CharDriver::create() callback is turned into a ChardevClass::open()
which is called from the newly introduced qemu_chardev_open().
"chardev-gdb" and "chardev-hci" are internal chardev and aren't
creatable directly with -chardev. Use a new internal flag to disable
them. We may want to use TYPE_USER_CREATABLE interface instead, or
perhaps allow -chardev usage.
Although in general we keep typename and macros private, unless the type
is being used by some other file, in this patch, all types and common
helper macros for qemu-char.c are in char.h. This is to help transition
now (some types must be declared early, while some aren't shared) and
when splitting in several units. This is to be improved later.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
vc_chr_write() is more appropriate than _puts() since no newline is
appended, even though it's not used only as a callback.
Keep "qemu_chr_parse" prefix, most chardev parse functions use this
prefix atm.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Instead of registering a vc handler to allocate the Gtk VC Chardev,
overwrite the console.c char driver.
A later patch, when switching to QOM, will register a default console vc
QOM class if none has been registered before.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Set errp to report errors up to the right monitor.
Use error_append_hint() to give hints about parameters on !qmp monitors,
instead of a direct fprintf() call.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Rename the types to follow the name of the chardev kind.
- socket: TCPChardev -> SocketChardev
- udp: NetChardev -> UdpChardev
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Pick a uniform chardev type name.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use common allocator for CharDriverState.
Rename the now untouched parent field.
The casts added are temporary, they are replaced with QOM type-safe
macros in a later patch in this series.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use a single allocation for CharDriverState, this avoids extra
allocations & pointers, and is a step towards more object-oriented
CharDriver.
Gtk console is a bit peculiar, gd_vc_chr_set_echo() used to have a
temporary VirtualConsole to save the echo bit. Instead now, we consider
whether vcd->console is set or not, and restore the echo bit saved in
VCDriverState when calling gd_vc_vte_init().
The casts added are temporary, they are replaced with QOM type-safe
macros in a later patch in this series.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use a feature flag rather than a structure field for "replay".
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This allows to remove the "is_mux" field from CharDriverState.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This shortens the code a bit.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This makes the code more declarative, and avoids duplicating the
information on all instances.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Number and kinds of backends is known at compile-time, use a fixed-sized
static array to simplify iterations & lookups.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
No need to allocate & copy fields, let's use static const struct instead.
Add an alias field to the CharDriver structure to cover the cases where
we previously registered a driver twice under two names.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>