If the signal is sampled high, this indicates that the system is
strapped to the "No Reboot" mode (ICH9 will disable the TCO Timer system
reboot feature). The status of this strap is readable via the NO_REBOOT
bit (CC: offset 0x3410:bit 5).
The NO_REBOOT bit is set when SPKR pin on ICH9 is sampled high. This bit
may be set or cleared by software if the strap is sampled low but may
not override the strap when it indicates "No Reboot".
This patch implements the logic where hardware has ability to set SPKR
pin through a property named "noreboot" and it's sampled high by
default.
Signed-off-by: Paulo Alcantara <pcacjr@zytor.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This interface provides some registers within a 32-byte range and can be
acessed through PCI-to-LPC bridge interface (PMBASE + 0x60).
It's commonly used as a watchdog timer to detect system lockups through
SMIs that are generated -- if TCO_EN bit is set -- on every timeout. If
NO_REBOOT bit is not set in GCS (General Control and Status register),
the system will be resetted upon second timeout if TCO_RLD register
wasn't previously written to prevent timeout.
This patch adds support to TCO watchdog logic and few other features
like mapping NMIs to SMIs (NMI2SMI_EN bit), system intruder detection,
etc. are not implemented yet.
Signed-off-by: Paulo Alcantara <pcacjr@zytor.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
MIPS doesn't need it, and including it creates problem as we are adding
dependency on ISA LPC bridge.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This reverts commit f5a5628cf0.
This was an old patch that had been already superseded by b0e5d90eb
("dataplane: endianness-aware accesses").
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Accesses to vring_avail_event and vring_used_event must honor the queue
endianness.
This patch allows cross-endian setups to use dataplane (tested with ppc64
on ppc64le, and vice-versa).
Suggested-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
The property can take values on, off or auto. The default is "off"
for KVM and pre-2.4 machines, otherwise "auto" (which makes it
available on TCG or on new-enough kernels).
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Q35's ACPI device is hard-coding SMM availability to KVM. Place the
logic where the board is created instead, so that it will be possible
to override it.
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We will enable SMM even if KVM is in use. Rename the field and
arguments.
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
These commands are handled entirely by QEMU. Do not raise an SMI
when they happen, because Windows (at least 2008r2) expects these
commands to work and (depending on the value of APMC_EN at
startup) the firmware might not have installed an SMI handler.
When this happens (e.g. the kernel supports SMIs, or you are using
TCG, but you have used "-machine smm=off") RIP is moved to 0x38000
where there is no code to execute.
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
* unlocked MMIO support in KVM
* support for compilation with ICC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJVmnuoAAoJEL/70l94x66DKTUH/RFrc20KXRkn/Pb/8qHY/wFz
Wt3YaS5VYPHElHbxHSdpwlV3K50FAX4QaC25Dnw4dsTelyxe5k7od+I7x8PQxD9v
3N+mFFF1BV6PqXTPVnUCnb14EXprJX524E97O6Z3lDGcwSLHDxeveSCk3IvMFErz
JzP3vtigSvtdPPQXlGcndP/r1EXeVjgNIsZ+NKaI/kmoSz1fHFrCN8hTnrxA9RSI
ZPhfmgHI5EMFtAf/HiZID6GSHOHajgeRT2bIiiy1okS++no0uRZlVMvcnFNPZHoG
e9XCGBXJSdmCoi7sIgShXirKszxYkRTbCyxxjz6aYfhrQzo0h+Yn9OPuvQrgynE=
=+YEv
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging
* more of Peter Crosthwaite's multiarch preparation patches
* unlocked MMIO support in KVM
* support for compilation with ICC
# gpg: Signature made Mon Jul 6 13:59:20 2015 BST using RSA key ID 78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>"
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* remotes/bonzini/tags/for-upstream:
exec: skip MMIO regions correctly in cpu_physical_memory_write_rom_internal
Stop including qemu-common.h in memory.h
kvm: Switch to unlocked MMIO
acpi: mark PMTIMER as unlocked
kvm: Switch to unlocked PIO
kvm: First step to push iothread lock out of inner run loop
memory: let address_space_rw/ld*/st* run outside the BQL
exec: pull qemu_flush_coalesced_mmio_buffer() into address_space_rw/ld*/st*
memory: Add global-locking property to memory regions
main-loop: introduce qemu_mutex_iothread_locked
main-loop: use qemu_mutex_lock_iothread consistently
Fix irq route entries exceeding KVM_MAX_IRQ_ROUTES
cpu-defs: Move out TB_JMP defines
include/exec: Move tb hash functions out
include/exec: Move standard exceptions to cpu-all.h
cpu-defs: Move CPU_TEMP_BUF_NLONGS to tcg
memory_mapping: Rework cpu related includes
cutils: allow compilation with icc
qemu-common: add VEC_OR macro
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The timer should fire the interrupt only if the IT (interrupt enable) bit
state of the control register is enabled.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The running timer can't be stopped because timer control code just
doesn't handle disabling the timer. Fix it by deleting the timer if
the enable bit is cleared.
The timer won't start periodic ticking if a ONE-SHOT -> PERIODIC mode
change happens after a one-shot tick was completed. Fix it by
re-starting ticking if the timer isn't ticking right now.
To avoid code churning, these two fixes are squashed in one commit.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The arm_gic_common reset function was missing reset code for
several of the GIC's state fields:
* bpr[]
* abpr[]
* priority1[]
* priority2[]
* sgi_pending[]
* irq_target[] (SMP configurations only)
These probably went unnoticed because most guests will either
never touch them, or will write to them in the process of
configuring the GIC before enabling interrupts.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1435602345-32210-1-git-send-email-peter.maydell@linaro.org
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
The interval interrupt is not set if the timer is in decrement mode.
This is because x >=0 and x < interval after leaving the while-loop.
Signed-off-by: Johannes Schlatow <schlatow@ida.ing.tu-bs.de>
Message-id: 20150630135821.51f3b4fd@johanness-latitude
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Version: GnuPG v1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=nQZA
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/jnsnow/tags/ide-pull-request' into staging
# gpg: Signature made Sat Jul 4 07:06:08 2015 BST using RSA key ID AAFC390E
# gpg: Good signature from "John Snow (John Huston) <jsnow@redhat.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: FAEB 9711 A12C F475 812F 18F2 88A9 064D 1835 61EB
# Subkey fingerprint: F9B7 ABDB BCAC DF95 BE76 CBD0 7DEF 8106 AAFC 390E
* remotes/jnsnow/tags/ide-pull-request: (35 commits)
ahci: fix sdb fis semantics
qtest/ahci: halted ncq migration test
ahci: Do not map cmd_fis to generate response
ahci: ncq migration
ahci: add get_cmd_header helper
ahci: add cmd header to ncq transfer state
qtest/ahci: halted NCQ test
ahci: correct ncq sector count
ahci: correct types in NCQTransferState
ahci: add rwerror=stop support for ncq
ahci: factor ncq_finish out of ncq_cb
ahci: refactor process_ncq_command
ahci: assert is_ncq for process_ncq
ahci: stash ncq command
ide: add limit to .prepare_buf()
qtest/ahci: ncq migration test
qtest/ahci: simple ncq data test
libqos/ahci: Force all NCQ commands to be LBA48
libqos/ahci: set the NCQ tag on command_commit
libqos/ahci: adjust expected NCQ interrupts
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There are two things to fix here:
The first one is subtle: the PxSACT register in the AHCI HBA has different
semantics from the field it is shadowing, the ACT field in the
Set Device Bits FIS.
In the HBA register, PxSACT acts as a bitfield indicating outstanding
NCQ commands where a set bit indicates a pending NCQ operation. The FIS
field however operates as an RWC register update to PxSACT, where a set
bit indicates a *successfully* completed command.
Correct the FIS semantics. At the same time, move the "clear finished"
action to the SDB FIS generation instead of the register read to mimick
how the other shadow registers work, which always just report the last
reported value from a FIS, and not the most current values which may
not have been reported by a FIS yet.
Lastly and more simply, SATA 3.2 section 13.6.4.2 (and later sections)
all specify that the Interrupt bit for the SDB FIS should always be set
to one for NCQ commands. That's currently the only time we generate this
FIS, so set it on all the time.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435767578-32743-16-git-send-email-jsnow@redhat.com
The Register D2H FIS should copy the current values of
the registers instead of just parroting back the same
values the guest sent back to it.
In this case, the SECTOR COUNT variables are actually
not generally meaningful in terms of standard commands
(See ATA8-AC3 Section 9.2 Normal Outputs), so it actually
probably doesn't matter what we put in here.
Meanwhile, we do need to use the Register update FIS from
the NCQ pathways (in error cases), so getting rid of
references to cur_cmd here is a win for AHCI concurrency.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435767578-32743-14-git-send-email-jsnow@redhat.com
Migrate the NCQ queue. This is solely for the benefit of halted commands,
since anything else should have completed and had any relevant status
flushed to the HBA registers already.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435767578-32743-13-git-send-email-jsnow@redhat.com
cur_cmd is an internal bookmark that points to the
current AHCI Command Header being processed by the
AHCI state machine. With NCQ needing to occasionally
rely on some of the same AHCI helpers, we cannot use
cur_cmd and will need to grab explicit pointers instead.
In an attempt to begin relying on the cur_cmd pointer
less, add a helper to let us specifically get the pointer
to the command header of particular interest.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435767578-32743-12-git-send-email-jsnow@redhat.com
While the rest of the AHCI device can rely on a single bookmarked
pointer for the AHCI Command Header currently being processed, NCQ
is asynchronous and may have many commands in flight simultaneously.
Add a cmdh pointer to the ncq_tfs object and make the sglist prepare
function take an AHCICmdHeader pointer so we can be explicit about
where we'd like to build SGlists from.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435767578-32743-11-git-send-email-jsnow@redhat.com
uint16_t isn't enough to hold the real sector count, since a value of
zero implies a full 64K sectors, so we need a uint32_t here.
We *could* cheat and pretend that this value is 0-based and fit it in
a uint16_t, but I'd rather waste 2 bytes instead of a future dev's
10 minutes when they forget to +1/-1 accordingly somewhere.
See SATA 3.2, section 13.6.4.1 "READ FPDMA QUEUED".
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435767578-32743-9-git-send-email-jsnow@redhat.com
Handle NCQ failures for cases where we want to halt the VM on IO errors.
Upon a VM state change, retry the halted NCQ commands.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435767578-32743-7-git-send-email-jsnow@redhat.com
When we add werror=stop or rerror=stop support to NCQ,
we'll want to take a codepath where we don't actually
complete the command, so factor that out into a new routine.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435767578-32743-6-git-send-email-jsnow@redhat.com
Split off execute_ncq_command so that we can call
it separately later if we desire.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435767578-32743-5-git-send-email-jsnow@redhat.com
We already checked this in the handle_cmd phase, so just
change this to an assertion and simplify the error logic.
(Also, fix the switch indent, because checkpatch.pl yelled.)
((Sorry for churn.))
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435767578-32743-4-git-send-email-jsnow@redhat.com
For migration and werror=stop/rerror=stop resume purposes,
it will be convenient to have the command handy inside of
ncq_tfs.
Eventually, we'd like to avoid reading from the FIS entirely
after the initial read, so this is a byte (hah!) sized step
in that direction.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435767578-32743-3-git-send-email-jsnow@redhat.com
prepare_buf should not always grab as many descriptors
as it can, sometimes it should self-limit.
For example, an NCQ transfer of 1 sector with a PRDT that
describes 4GiB of data should not copy 4GiB of data, it
should just transfer that first 512 bytes.
PIO is not affected, because the dma_buf_rw dma helpers
already have a byte limit built-in to them, but DMA/NCQ
will exhaust the entire list regardless of requested size.
AHCI 1.3 specifies in section 6.1.6 Command List Underflow that
NCQ is not required to detect underflow conditions. Non-NCQ
pathways signal underflow by writing to the PRDBC field, which
will already occur by writing the actual transferred byte count
to the PRDBC, signaling the underflow.
Our NCQ pathways aren't required to detect underflow, but since our DMA
backend uses the size of the PRDT to determine the size of the transer,
if our PRDT is bigger than the transaction (the underflow condition) it
doesn't cost us anything to detect it and truncate the PRDT.
This is a recoverable error and is not signaled to the guest, in either
NCQ or normal DMA cases.
For BMDMA, the existing pathways should see no guest-visible difference,
but any bytes described in the overage will no longer be transferred
before indicating to the guest that there was an underflow.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435767578-32743-2-git-send-email-jsnow@redhat.com
This value should not be size-corrected, 0 sectors does not imply
1 sector(s). This is just debug information, but it's misleading!
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435016308-6150-8-git-send-email-jsnow@redhat.com
Most of the time, these bits can be safely ignored. For the purposes
of debugging however, it's nice to know that they're not being used.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435016308-6150-7-git-send-email-jsnow@redhat.com
There's no real reason to have it bundled together, and this way
is a little nicer to follow if you have the AHCI spec pulled up.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435016308-6150-6-git-send-email-jsnow@redhat.com
Don't attempt the NCQ transfer if the PRDT we were given is not big
enough to perform the entire transfer.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435016308-6150-5-git-send-email-jsnow@redhat.com
Set some appropriate error bits for NCQ for us.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435016308-6150-4-git-send-email-jsnow@redhat.com
Trivial cleanup that I didn't want to tack-on to anything else.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435016308-6150-3-git-send-email-jsnow@redhat.com
Several fields of the NCQFIS structure are ambiguously named. This patch
clarifies the intended (if unsupported) usage of the NCQ fields to aid
in creating more meaningful debug messages through the NCQ codepaths.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1435016308-6150-2-git-send-email-jsnow@redhat.com
The only guidance the AHCI specification gives on memory access is:
"Register accesses shall have a maximum size of 64-bits; 64-bit access
must not cross an 8-byte alignment boundary."
I interpret this to mean that aligned or unaligned 1, 2 and 4 byte
accesses should work, as well as aligned 8 byte accesses.
In practice, a real Q35/ICH9 responds to 1, 2, 4 and 8 byte reads
regardless of alignment. Windows 7 can be observed making 1 byte
reads to the middle of 32 bit registers to fetch error codes.
Introduce a wrapper to support unaligned accesses to AHCI.
This wrapper will support aligned 8 byte reads, but will make
no effort to support unaligned 8 byte reads, which although they
will work on real hardware, are not guaranteed to work and do
not appear to be used by either Windows or Linux.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 1434470575-21625-2-git-send-email-jsnow@redhat.com
Start storing the (start_addr, end_addr) of the pc-dimm memory
in corresponding numa_info[node] so that this information can be used
to lookup node by address.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
HotplugHandlerClass::plug() shouldn't fail and hence use error_abort
to abort if it fails.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
pc_dimm_plug() has code that will be needed for memory plug handlers
in other archs too. Extract code from pc_dimm_plug() into a generic
routine pc_dimm_memory_plug() that resides in pc-dimm.c. Also
correspondingly refactor re-usable unplug code into pc_dimm_memory_unplug().
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Move hotplug_memory_base and hotplug_memory fields of PCMachineState
into a separate structure so that the same can be made use of from
other architectures supporing memory hotplug.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Add display and head properties for input routing to
virtio-input devices, update multiseat documentation.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The section footer changes commit f68945d42b ("Add a protective
section footer") and commit 37fb569c01 ("Disable section footers
on older machine types") broke migration for any non-versioned
machines.
This pinpoints a problem of s390-ccw machines: it needs to
be versioned to be compatible with future changes in common
code data structures such as section footers.
Let's introduce a version scheme for s390-ccw-virtio machines.
We will use the old s390-ccw-virtio name as alias to the latest
version as all existing libvirt XML for the ccw type were expanded
by libvirt to that name.
The only downside of this patch is, that the old alias s390-ccw
will no longer be available as machines can have only one alias,
but it should not really matter.
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Cc: Juan Quintela <quintela@redhat.com>
Cc: Boris Fiuczynski <fiuczy@linux.vnet.ibm.com>
Cc: Jason J. Herne <jjherne@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Message-Id: <1435742217-62246-1-git-send-email-borntraeger@de.ibm.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
commit fa92e218df ("s390x/ipl: avoid sign extension") introduced
a regression:
qemu-system-s390x -drive file=image.qcow,format=qcow2
does not boot, the bios states
"No virtio-blk device found!"
adding bootindex=1 does boot.
The reason is that the uint32_t as return value will not do the right
thing for the return -1 (default without bootindex).
The bios itself, will interpret a 64bit -1 as autodetect (but it will
interpret 32bit -1 as ccw device address ff.ff.ffff)
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: qemu-stable@nongnu.org # v2.3.0
Tested-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
We need to migrate the revision field as well. No compatibility
concerns as we already introduced migration of ->config_vector in
this release.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Support the new CCW_CMD_SET_VQ format for virtio-1 devices.
While we're at it, refactor the code a bit and enforce big endian
fields (which had always been required, even for legacy).
Reviewed-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Handle the virtio-ccw revision according to what the guest sets.
When revision 1 is selected, we have a virtio-1 standard device
with byteswapping for the virtio rings.
When a channel gets disabled, we have to revert to the legacy behavior
in case the next user of the device does not negotiate the revision 1
anymore (e.g. the boot firmware uses revision 1, but the operating
system only uses the legacy mode).
Note that revisions > 0 are still disabled.
[CH: assure memory accesses are always BE]
Signed-off-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Accessing QEMU_CLOCK_VIRTUAL is thread-safe.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1434646046-27150-9-git-send-email-pbonzini@redhat.com>
Paulo Alcantara
Michael S. Tsirkin
Cornelia Huck
Greg Kurz
Paolo Bonzini
Peter Maydell
Dmitry Osipenko
Johannes Schlatow
John Snow
Bharata B Rao
Gerd Hoffmann
Christian Borntraeger
Thomas Huth
Alberto Garcia