The SysTick timer isn't really part of the NVIC proper;
we just modelled it that way back when we couldn't
easily have devices that only occupied a small chunk
of a memory region. Split it out into its own device.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1487604965-23220-10-git-send-email-peter.maydell@linaro.org
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
The i.MX timer device can be reset by writing to the SWR bit
of the CR register. This has to behave differently from hard
(power-on) reset because it does not reset all of the bits
in the CR register.
We were incorrectly implementing soft reset and hard reset
the same way, and in addition had a logic error which meant
that we were clearing the bits that soft-reset is supposed
to preserve and not touching the bits that soft-reset clears.
This was not correct behaviour for either kind of reset.
Separate out the soft reset and hard reset code paths, and
correct the handling of reset of the CR register so that it
is correct in both cases.
Signed-off-by: Kurban Mallachiev <mallachiev@ispras.ru>
[PMM: rephrased commit message, spacing on operators;
use bool rather than int for is_soft_reset]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Provide a new function mips_gictimer_get_freq() which returns the
frequency at which a GIC timer will count. This will be useful for
boards which perform setup based upon this frequency.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
The member VMStateField.start is used for two things, partial data
migration for VBUFFER data (basically provide migration for a
sub-buffer) and for locating next in QTAILQ.
The implementation of the VBUFFER feature is broken when VMSTATE_ALLOC
is used. This however goes unnoticed because actually partial migration
for VBUFFER is not used at all.
Let's consolidate the usage of VMStateField.start by removing support
for partial migration for VBUFFER.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Message-Id: <20170203175217.45562-1-pasic@linux.vnet.ibm.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
The m48t59 device supports both ISA and direct sysbus attached versions of
the device in the one .c file. This can be awkward for some embedded
machine types which need the sysbus M48T59, but don't want to pull in the
ISA bus code and its other dependencies.
Therefore, this patch splits out the code for the ISA attached M48T59 into
its own C file. It will be built when both CONFIG_M48T59 and
CONFIG_ISA_BUS are enabled.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
This patch disables the update of the periodic timer of mc146818rtc
in record/replay mode. State of this timer is saved and therefore does
not need to be updated in record/replay mode.
Read of RTC breaks the replay because all rtc reads have to be the same
as in record mode.
Signed-off-by: Pavel Dovgalyuk <pavel.dovgaluk@ispras.ru>
Message-Id: <20170124071730.4572.41874.stgit@PASHA-ISP>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add the Altera timer model.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chris Wulff <crwulff@gmail.com>
Cc: Jeff Da Silva <jdasilva@altera.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Sandra Loosemore <sandra@codesourcery.com>
Cc: Yves Vandervennet <yvanderv@altera.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Message-Id: <20170118220146.489-6-marex@denx.de>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Current migration code cannot handle some data structures such as
QTAILQ in qemu/queue.h. Here we extend the signatures of put/get
in VMStateInfo so that customized handling is supported. put now
will return int type.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Jianjun Duan <duanj@linux.vnet.ibm.com>
Message-Id: <1484852453-12728-2-git-send-email-duanj@linux.vnet.ibm.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
reset mc146818rtc device when RESET event happens.
Fix the problem:
1. Guest boot the second cpu, set CMOS_RESET_CODE 0x0a to protect selfboot;
2. VM being reset by others, hmp_system_reset;
3. seabios resume check the CMOS_RESET_CODE, if 0x0a, jump to the BDA
resume execution by jump via 40h:0067h;
4. Guest halt;
Signed-off-by: hangaohuai <hangaohuai@huawei.com>
Message-Id: <20161219060336.10176-1-hangaohuai@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a return value to the event handler. Some I2C devices will
NAK if they have no data, so allow them to do this. This required
the following changes:
Go through all the event handlers and change them to return int
and return 0.
Modify i2c_start_transfer to terminate the transaction on a NAK.
Modify smbus handing to not assert if a NAK occurs on a second
operation, and terminate the transaction and return -1 instead.
Add some information on semantics to I2CSlaveClass.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a NULL check for i2c slave init callbacks, so that we no longer
need to implement empty init functions.
Signed-off-by: Alastair D'Silva <alastair@d-silva.org>
Message-id: 20161202054617.6749-4-alastair@au1.ibm.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: squashed in later tweak from Alistair to if() phrasing]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some files contain multiple #includes of the same header file.
Removed most of those unnecessary duplicate entries using
scripts/clean-includes.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Anand J <anand.indukala@gmail.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The STM32F2XX Timer emulator uses a 16 bit prescaler value to
limit the timer clock rate. It does that by dividing the timer
frequency. If the prescaler 's->tim_psc' was set to be UINT_MAX,
it'd lead to divide by zero error. Limit prescaler value to 16
bits to avoid it.
Reported-by: Huawei PSIRT <psirt@huawei.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-id: 1476800269-31902-1-git-send-email-ppandit@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
ARM A9MP processor has a peripheral timer with an auto-increment
register, which holds an increment step value. A user could set
this value to zero. When auto-increment control bit is enabled,
it leads to an infinite loop in 'a9_gtimer_update' while
updating comparator value. Remove this loop incrementing the
comparator value.
Reported-by: Li Qiang <liqiang6-s@360.cn>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-id: 1476733226-11635-1-git-send-email-ppandit@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Current ARM MPTimer implementation uses QEMUTimer for the actual timer,
this implementation isn't complete and mostly tries to duplicate of what
generic ptimer is already doing fine.
Conversion to ptimer brings the following benefits and fixes:
- Simple timer pausing implementation
- Fixes counter value preservation after stopping the timer
- Properly handles prescaler != 0 / counter = 0 / load = 0 cases
- Code simplification and reduction
Bump VMSD to version 3, since VMState is changed and is not compatible
with the previous implementation.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: 37f378c33bb5a28d5cd71167a6bd5bff5e59cbc3.1475421224.git.digetx@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If correctly configured allow the STM32F2xx timer to print
out the PWM duty cycle information.
Signed-off-by: Alistair Francis <alistair@alistair23.me>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: cdb59039a25e061615713a94b40797baa12ea9f9.1474742262.git.alistair@alistair23.me
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
qemu tracks guest time based on vector [base_rtc, last_update], in which
last_update stands for a monotonic tick which is actually uptime of the
host.
according to rtc implementation codes of recent releases and upstream,
after
migration, the time base vector [base_rtc, last_update] isn't updated to
coordinate with the destionation host, ie. qemu doesnt update last_update
to
uptime of the destination host.
what problem have we got because of this bug? after migration, guest time
may
jump back to several days ago, that will make some critical business
applications,
such as lotus notes, malfunction.
this patch is trying to fix the problem. first, when vmsave in progress,
we
rtc_update_time to refresh time stamp in cmos array, then during
vmrestore,
we rtc_set_time to update qemu base_rtc and last_update variable according
to time
stamp in cmos array.
Signed-off-by: Junlian Bell <zhongjun@sangfor.com.cn>
Message-Id: <20160926124101.2364-1-zhongjun@sangfor.com.cn>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
'char const' means the same thing as 'const char', but we
use the former in only a handful of places and we use the
latter over six thousand times. Switch the imx reg_name()
functions to bring them in line with everything else.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some of the timer devices may behave differently from what ptimer
provides. Introduce ptimer policy feature that allows ptimer users to
change default and wrong timer behaviour, for example to continuously
trigger periodic timer when load value is equal to "0".
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Message-id: 994cd608ec392da6e58f0643800dda595edb9d97.1473252818.git.digetx@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Changes:
* support 10-bit ASIDs
* MIPS64R6-generic renamed to I6400
* initial GIC support
* implement RESET_BASE register in CM GCR
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJXhMtOAAoJEFIRjjwLKdprahQH/2qBMp7Hnucy7jhiPHRtRZTo
zZAhuRJ0Z2LT9xH+sTg3HcjHI7aXps5cG2f7Fw4X/JKNRY4KO19yEBnMhc5he2Ut
XPtHCeMXXq6zU4RMHqlx6wChHn5AUll/3EeSvm6JMV+HhE6oDBk1yl5C8ipPlVCd
KEz6LlUFNMbuxu2tM4DoMNAWeKmunBx3vO+JuErB6hjCWM5G0mV9aPDkbwTOmVLn
qGgzzmNDiPE6JWrSpbHetsdCO7V9xtXzhcFsu240GJ/+XJMjUXb1m6ETsJxT9EYh
vLfFzwozBSjX6ZQZVNFIAeJZnq96NOHqZ56sU7s4YktVXjl26JAahScTTH0aiNo=
=sTce
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/lalrae/tags/mips-20160712' into staging
MIPS patches 2016-07-12
Changes:
* support 10-bit ASIDs
* MIPS64R6-generic renamed to I6400
* initial GIC support
* implement RESET_BASE register in CM GCR
# gpg: Signature made Tue 12 Jul 2016 11:49:50 BST
# gpg: using RSA key 0x52118E3C0B29DA6B
# gpg: Good signature from "Leon Alrae <leon.alrae@imgtec.com>"
# Primary key fingerprint: 8DD3 2F98 5495 9D66 35D4 4FC0 5211 8E3C 0B29 DA6B
* remotes/lalrae/tags/mips-20160712:
target-mips: enable 10-bit ASIDs in I6400 CPU
target-mips: support CP0.Config4.AE bit
target-mips: change ASID type to hold more than 8 bits
target-mips: add ASID mask field and replace magic values
target-mips: replace MIPS64R6-generic with the real I6400 CPU model
hw/mips_cmgcr: implement RESET_BASE register in CM GCR
hw/mips_cpc: make VP correctly start from the reset vector
target-mips: add exception base to MIPS CPU
hw/mips/cps: create GIC block inside CPS
hw/mips: implement Global Interrupt Controller
hw/mips: implement GIC Interval Timer
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The interval timer is similar to the CP0 Count/Compare timer within
each processor. The difference is the GIC_SH_COUNTER register is global
to the system so that all processors have the same time reference.
To ease implementation, all VPs are having its own QEMU timer but sharing
global settings and registers such as GIC_SH_CONFIG.COUTNSTOP and
GIC_SH_COUNTER.
MIPS GIC Interval Timer does support upto 64 bits of Count register but
in this implementation it is limited to 32 bits only.
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
In various Freescale SOCs, the GPT timers can be configured to select
its input clock.
Depending on the SOC the set of available input clocks may vary.
The actual single GPT definition was no good enough and because of it
booting the sabrelite board with a i.MX6DL device tree would fail
because of an incorrect input clock definition for the i.MX6DL SOC.
This patch fixes the i.MX6DL boot failure by adding the ability to
define a different set of input clocks depending on the considered SOC.
A different class has been defined for i.MX25, i.MX31 and i.MX6 each with
its specific set of input clocks.
The patch has been tested by booting KZM, i.MX25 PDK, i.MX6Q sabrelite
and i.MX6DL sabrelite.
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Message-id: 1467325619-8374-1-git-send-email-jcd@tribudubois.net
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: fixed spacing round '/' operator]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The MC146818 RTC device has output IRQ line. Currently the corresponding field
is only accessible through direct access. Such access violates Qemu model.
The patch makes the field accessible through GPIO. It also updates the setting
of the IRQ during initialization.
Signed-off-by: Efimov Vasily <real@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Version: GnuPG v1
iQEcBAABAgAGBQJXaFInAAoJEJykq7OBq3PI6VsH/0Sfgbdo1RksYuQwb/y92sCW
EN+lxUZ+OLfgrc8PYgNZwfSM3rsfYhznL0MAXOeEe7Ahabi07w7DhGR8WvwfAOlI
G96FRuvrIPfv5u6U6fwS4CvG3TIHVLxfHKCsTpPUmH8U5CNx/x/tpjNiWN1dj6t+
sXybSjYHfZfiZy2tI9MFIFWCdxnF/pl0QAPhbRqc8Y/RQTDrPKRjLpz+nitN/u96
5TS7KlELyQuP91YMmLceYSmIkHbxW703h+iE2n4hov0uZCP8Jil+2Jsd3ziQSRlL
j6LqexQ2ViBGdDSfiZGYES2VPlsHOCwb4G+IgWBStfZg1ppaXENvcDzPrgrB+L4=
=eUnF
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stefanha/tags/tracing-pull-request' into staging
# gpg: Signature made Mon 20 Jun 2016 21:29:27 BST
# gpg: using RSA key 0x9CA4ABB381AB73C8
# gpg: Good signature from "Stefan Hajnoczi <stefanha@redhat.com>"
# gpg: aka "Stefan Hajnoczi <stefanha@gmail.com>"
# Primary key fingerprint: 8695 A8BF D3F9 7CDA AC35 775A 9CA4 ABB3 81AB 73C8
* remotes/stefanha/tags/tracing-pull-request: (42 commits)
trace: split out trace events for linux-user/ directory
trace: split out trace events for qom/ directory
trace: split out trace events for target-ppc/ directory
trace: split out trace events for target-s390x/ directory
trace: split out trace events for target-sparc/ directory
trace: split out trace events for net/ directory
trace: split out trace events for audio/ directory
trace: split out trace events for ui/ directory
trace: split out trace events for hw/alpha/ directory
trace: split out trace events for hw/arm/ directory
trace: split out trace events for hw/acpi/ directory
trace: split out trace events for hw/vfio/ directory
trace: split out trace events for hw/s390x/ directory
trace: split out trace events for hw/pci/ directory
trace: split out trace events for hw/ppc/ directory
trace: split out trace events for hw/9pfs/ directory
trace: split out trace events for hw/i386/ directory
trace: split out trace events for hw/isa/ directory
trace: split out trace events for hw/sd/ directory
trace: split out trace events for hw/sparc/ directory
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Move all trace-events for files in the hw/timer/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-20-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The old milkymist.org domain just forwards to mm-labs.hk nowadays. I've
created a mirror of the documents.
Signed-off-by: Michael Walle <michael@walle.cc>
* split the old SysBus init function into an instance_init
and a Device realize function
* use DeviceClass::realize instead of SysBusDeviceClass::init
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Acked-by: Michael Walle <michael@walle.cc>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Michael Walle <michael@walle.cc>
* split the old SysBus init function into an instance_init
and a Device realize function
* use DeviceClass::realize instead of SysBusDeviceClass::init
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Acked-by: Michael Walle <michael@walle.cc>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Michael Walle <michael@walle.cc>
Use Coccinelle script to replace 'ret = E; return ret' with
'return E'. The script will do the substitution only when the
function return type and variable type are the same.
Manual fixups:
* audio/audio.c: coding style of "read (...)" and "write (...)"
* block/qcow2-cluster.c: wrap line to make it shorter
* block/qcow2-refcount.c: change indentation of wrapped line
* target-tricore/op_helper.c: fix coding style of
"remainder|quotient"
* target-mips/dsp_helper.c: reverted changes because I don't
want to argue about checkpatch.pl
* ui/qemu-pixman.c: fix line indentation
* block/rbd.c: restore blank line between declarations and
statements
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <1465855078-19435-4-git-send-email-ehabkost@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[Unused Coccinelle rule name dropped along with a redundant comment;
whitespace touched up in block/qcow2-cluster.c; stale commit message
paragraph deleted]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Value matching allows Linux to boot with CONFIG_NO_HZ_IDLE=y on the
palmetto-bmc machine. Two match registers are provided for each timer.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1465974248-20434-1-git-send-email-andrew@aj.id.au
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
muldiv64() is "uint64_t muldiv64(uint64_t a, uint32_t b, uint32_t c)"
Some time it is used as muldiv64(uint32_t a, uint64_t b, uint32_t c)"
This patch is the result of coccinelle script
scripts/coccinelle/swap_muldiv64.cocci to reorder arguments.
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
This is not visible with the default "log" trace backend. With other
backends however trace.h does not include qemu/log.h, resulting in
build failures.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1463745452-25831-2-git-send-email-pbonzini@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This reverts commit 0d63b2dd31.
This change was originally intended to correct the HPET behavior
in conjunction with Linux, however the behavior that it actually creates
is not compatible with the ioapic.c implementation; it used to be
compatible with KVM's own IOAPIC but it is not anymore.
Signed-off-by: Bill Paul <wpaul@windriver.com>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Richard Henderson <rth@twiddle.net>
CC: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <201604051558.20070.wpaul@windriver.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move declarations out of qemu-common.h for functions declared in
utils/ files: e.g. include/qemu/path.h for utils/path.c.
Move inline functions out of qemu-common.h and into new files (e.g.
include/qemu/bcd.h)
Signed-off-by: Veronia Bahaa <veroniabahaa@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch replaces get_ticks_per_sec() calls with the macro
NANOSECONDS_PER_SECOND. Also, as there are no callers, get_ticks_per_sec()
is then removed. This replacement improves the readability and
understandability of code.
For example,
timer_mod(fdctrl->result_timer,
qemu_clock_get_ns(QEMU_CLOCK_VIRTUAL) + (get_ticks_per_sec() / 50));
NANOSECONDS_PER_SECOND makes it obvious that qemu_clock_get_ns
matches the unit of the expression on the right side of the plus.
Signed-off-by: Rutuja Shah <rutu.shah.26@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 57cb38b included qapi/error.h into qemu/osdep.h to get the
Error typedef. Since then, we've moved to include qemu/osdep.h
everywhere. Its file comment explains: "To avoid getting into
possible circular include dependencies, this file should not include
any other QEMU headers, with the exceptions of config-host.h,
compiler.h, os-posix.h and os-win32.h, all of which are doing a
similar job to this file and are under similar constraints."
qapi/error.h doesn't do a similar job, and it doesn't adhere to
similar constraints: it includes qapi-types.h. That's in excess of
100KiB of crap most .c files don't actually need.
Add the typedef to qemu/typedefs.h, and include that instead of
qapi/error.h. Include qapi/error.h in .c files that need it and don't
get it now. Include qapi-types.h in qom/object.h for uint16List.
Update scripts/clean-includes accordingly. Update it further to match
reality: replace config.h by config-target.h, add sysemu/os-posix.h,
sysemu/os-win32.h. Update the list of includes in the qemu/osdep.h
comment quoted above similarly.
This reduces the number of objects depending on qapi/error.h from "all
of them" to less than a third. Unfortunately, the number depending on
qapi-types.h shrinks only a little. More work is needed for that one.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
[Fix compilation without the spice devel packages. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Implement basic ASPEED timer functionality for the AST2400 SoC[1]: Up to
8 timers can independently be configured, enabled, reset and disabled.
Some hardware features are not implemented, namely clock value matching
and pulse generation, but the implementation is enough to boot the Linux
kernel configured with aspeed_defconfig.
[1] http://www.aspeedtech.com/products.php?fPath=20&rId=376
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1458096317-25223-2-git-send-email-andrew@aj.id.au
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
EPIT, GPT and other i.MX timers are using "abstract" clocks among which
a CLK_IPG_HIGH clock.
On i.MX25 and i.MX31 CLK_IPG and CLK_IPG_HIGH are mapped to the same clock
but on other SOC like i.MX6 they are mapped to distinct clocks.
This patch add the CLK_IPG_HIGH to prepare for SOC where these 2 clocks are
different.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Message-id: 224bf650194760284cb40630e985867e1373276a.1456868959.git.jcd@tribudubois.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This way all CCM clock defines/enums are named CLK_XXX
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Message-id: 8537df765c1713625c7a8b9aca4c7ca60b42e0c0.1456868959.git.jcd@tribudubois.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
