Provide a trivial implementation with zero limited ordering regions,
which causes the LDLAR and STLLR instructions to devolve into the
LDAR and STLR instructions from the base ARMv8.0 instruction set.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20181210150501.7990-4-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Replace arm_hcr_el2_{fmo,imo,amo} with a more general routine
that also takes SCR_EL3.NS (aka arm_is_secure_below_el3) into
account, as documented for the plethora of bits in HCR_EL2.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20181210150501.7990-2-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The bulk of the work here, beyond base HPD, is defining the
TTBCR2 register. In addition we must check TTBCR.T2E, which
is not present (RES0) for AArch64.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20181203203839.757-11-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Because EL3 has a fixed execution mode, we can properly decide
which of the bits are RES{0,1}.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20181203203839.757-8-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Post v8.4 bits taken from SysReg_v85_xml-00bet8.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20181203203839.757-4-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Post v8.3 bits taken from SysReg_v85_xml-00bet8.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20181203203839.757-3-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
At the same time, define the fields for these registers,
and use those defines in arm_pamax().
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20181203203839.757-2-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: fixed up typo (s/achf/ahcf/) belatedly spotted by RTH]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently we track the state of the four irq lines from the GIC
only via the cs->interrupt_request or KVM irq state. That means
that we assume that an interrupt is asserted if and only if the
external line is set. This assumption is incorrect for VIRQ
and VFIQ, because the HCR_EL2.{VI,VF} bits allow assertion
of VIRQ and VFIQ separately from the state of the external line.
To handle this, start tracking the state of the external lines
explicitly in a CPU state struct field, as is common practice
for devices.
The complicated part of this is dealing with inbound migration
from an older QEMU which didn't have this state. We assume in
that case that the older QEMU did not implement the HCR_EL2.{VI,VF}
bits as generating interrupts, and so the line state matches
the current state in cs->interrupt_request. (This is not quite
true between commit 8a0fc3a29f and its revert, but
that commit is broken and never made it into any released QEMU
version.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20181109134731.11605-3-peter.maydell@linaro.org
The test was incomplete and incorrectly caused debug exceptions to be
generated when returning to EL2 after a failed attempt to single-step
an EL1 instruction. Fix this while cleaning up the function a little.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20181109152119.9242-8-alex.bennee@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We already have this symbol defined so lets use it.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20181109152119.9242-7-alex.bennee@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When populating id registers from kvm, on a host that doesn't support
aarch32 mode at all, neither arm_div nor jazelle will be supported either.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20181102102025.3546-1-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20181016223115.24100-9-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20181016223115.24100-8-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Having V6 alone imply jazelle was wrong for cortex-m0.
Change to an assertion for V6 & !M.
This was harmless, because the only place we tested ARM_FEATURE_JAZELLE
was for 'bxj' in disas_arm(), which is unreachable for M-profile cores.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20181016223115.24100-6-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Both arm and thumb2 division are controlled by the same ISAR field,
which takes care of the arm implies thumb case. Having M imply
thumb2 division was wrong for cortex-m0, which is v6m and does not
have thumb2 at all, much less thumb2 division.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20181016223115.24100-5-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Most of the v8 extensions are self-contained within the ISAR
registers and are not implied by other feature bits, which
makes them the easiest to convert.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20181016223115.24100-4-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Create struct ARMISARegisters, to be accessed during translation.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20181016223115.24100-2-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch extends the qemu-kvm state sync logic with support for
KVM_GET/SET_VCPU_EVENTS, giving access to yet missing SError exception.
And also it can support the exception state migration.
The SError exception states include SError pending state and ESR value,
the kvm_put/get_vcpu_events() will be called when set or get system
registers. When do migration, if source machine has SError pending,
QEMU will do this migration regardless whether the target machine supports
to specify guest ESR value, because if target machine does not support that,
it can also inject the SError with zero ESR value.
Signed-off-by: Dongjiu Geng <gengdongjiu@huawei.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1538067351-23931-3-git-send-email-gengdongjiu@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20181008212205.17752-3-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
At present we assert:
arm_el_is_aa64: Assertion `el >= 1 && el <= 3' failed.
The comment in arm_el_is_aa64 explains why asking about EL0 without
extra information is impossible. Add an extra argument to provide
it from the surrounding context.
Fixes: 0ab5953b00
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20181008212205.17752-2-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Define EXCP_STKOF, and arrange for it to cause us to take
a UsageFault with CFSR.STKOF set.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20181002163556.10279-3-peter.maydell@linaro.org
The Arm v8M architecture includes hardware stack limit checking.
When certain instructions update the stack pointer, if the new
value of SP is below the limit set in the associated limit register
then an exception is taken. Add a TB flag that tracks whether
the limit-checking code needs to be emitted.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20181002163556.10279-2-peter.maydell@linaro.org
Use the existing helpers to determine if (1) the fpu is enabled,
(2) sve state is enabled, and (3) the current sve vector length.
Tested-by: Laurent Desnogues <laurent.desnogues@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20181005175350.30752-6-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
SVE vector length can change when changing EL, or when writing
to one of the ZCR_ELn registers.
For correctness, our implementation requires that predicate bits
that are inaccessible are never set. Which means noticing length
changes and zeroing the appropriate register bits.
Tested-by: Laurent Desnogues <laurent.desnogues@gmail.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20181005175350.30752-5-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Following the bulk conversion of the iwMMXt code, there are
just a handful of hard coded tabs in target/arm; fix them.
This is a whitespace-only patch.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180821165215.29069-4-peter.maydell@linaro.org
When support for FZ16 was added, we failed to include the bit
within FPCR_MASK, which means that it could never be set.
Continue to zero FZ16 when ARMv8.2-FP16 is not enabled.
Fixes: d81ce0ef2c
Cc: qemu-stable@nongnu.org (3.0.1)
Reported-by: Laurent Desnogues <laurent.desnogues@gmail.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Laurent Desnogues <laurent.desnogues@gmail.com>
Tested-by: Laurent Desnogues <laurent.desnogues@gmail.com>
Message-id: 20180810193129.1556-2-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This allows the default (and maximum) vector length to be set
from the command-line. Which is extraordinarily helpful in
debugging problems depending on vector length without having to
bake knowledge of PR_SET_SVE_VL into every guest binary.
Cc: qemu-stable@nongnu.org (3.0.1)
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The IMO, FMO and AMO bits in HCR_EL2 are defined to "behave as
1 for all purposes other than direct reads" if HCR_EL2.TGE
is set and HCR_EL2.E2H is 0, and to "behave as 0 for all
purposes other than direct reads" if HCR_EL2.TGE is set
and HRC_EL2.E2H is 1.
To avoid having to check E2H and TGE everywhere where we test IMO and
FMO, provide accessors arm_hcr_el2_imo(), arm_hcr_el2_fmo()and
arm_hcr_el2_amo(). We don't implement ARMv8.1-VHE yet, so the E2H
case will never be true, but we include the logic to save effort when
we eventually do get to that.
(Note that in several of these callsites the change doesn't
actually make a difference as either the callsite is handling
TGE specially anyway, or the CPU can't get into that situation
with TGE set; we change everywhere for consistency.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180724115950.17316-5-peter.maydell@linaro.org
If the "trap general exceptions" bit HCR_EL2.TGE is set, we
must mask all virtual interrupts (as per DDI0487C.a D1.14.3).
Implement this in arm_excp_unmasked().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180724115950.17316-2-peter.maydell@linaro.org
This register was added to aa32 state by ARMv8.2.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180629001538.11415-6-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We've already added the helpers with an SVE patch, all that remains
is to wire up the aa64 and aa32 translators. Enable the feature
within -cpu max for CONFIG_USER_ONLY.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180627043328.11531-36-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This feature is intended to distinguish ARMv8-M variants: Baseline and
Mainline. ARMv7-M compatibility requires the Main Extension. ARMv6-M
compatibility is provided by all ARMv8-M implementations.
Signed-off-by: Julia Suvorova <jusual@mail.ru>
Message-id: 20180622080138.17702-2-jusual@mail.ru
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180516223007.10256-7-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Generate an XML description for the cp-regs.
Register these regs with the gdb_register_coprocessor().
Add arm_gdb_get_sysreg() to use it as a callback to read those regs.
Add a dummy arm_gdb_set_sysreg().
Signed-off-by: Abdallah Bouassida <abdallah.bouassida@lauterbach.com>
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1524153386-3550-4-git-send-email-abdallah.bouassida@lauterbach.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is a preparation for the coming feature of creating dynamically an XML
description for the ARM sysregs.
A register has ARM_CP_NO_GDB enabled will not be shown in the dynamic XML.
This bit is enabled automatically when creating CP_ANY wildcard aliases.
This bit could be enabled manually for any register we want to remove from the
dynamic XML description.
Signed-off-by: Abdallah Bouassida <abdallah.bouassida@lauterbach.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1524153386-3550-2-git-send-email-abdallah.bouassida@lauterbach.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The insns in the ARMv8.1-Atomics are added to the existing
load/store exclusive and load/store reg opcode spaces.
Rearrange the top-level decoders for these to accomodate.
The Atomics insns themselves still generate Unallocated.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180508151437.4232-8-richard.henderson@linaro.org
[PMM: Drop the ARM_FEATURE_V8_1 feature flag]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is a bug fix to ensure 64-bit reads of these registers don't read
adjacent data.
Signed-off-by: Aaron Lindsay <alindsay@codeaurora.org>
Message-id: 1523997485-1905-13-git-send-email-alindsay@codeaurora.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Because the design of the PMU requires that the counter values be
converted between their delta and guest-visible forms for mode
filtering, an additional hook which occurs before the EL is changed is
necessary.
Signed-off-by: Aaron Lindsay <alindsay@codeaurora.org>
Message-id: 1523997485-1905-8-git-send-email-alindsay@codeaurora.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This eliminates the need for fetching it from el_change_hook_opaque, and
allows for supporting multiple el_change_hooks without having to hack
something together to find the registered opaque belonging to GICv3.
Signed-off-by: Aaron Lindsay <alindsay@codeaurora.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1523997485-1905-6-git-send-email-alindsay@codeaurora.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
cpu_init(cpu_model) were replaced by cpu_create(cpu_type) so
no users are left, remove it.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au> (ppc)
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <1518000027-274608-6-git-send-email-imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
it will be used for providing to cpu name resolving class for
parsing cpu model for system and user emulation code.
Along with change add target to null-machine tests, so
that when switch to CPU_RESOLVING_TYPE happens,
it would ensure that null-machine usecase still works.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu> (m68k)
Acked-by: David Gibson <david@gibson.dropbear.id.au> (ppc)
Acked-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de> (tricore)
Message-Id: <1518000027-274608-4-git-send-email-imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
[ehabkost: Added macro to riscv too]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Currently we query the host CPU features in the class init function
for the TYPE_ARM_HOST_CPU class, so that we can later copy them
from the class object into the instance object in the object
instance init function. This is awkward for implementing "-cpu max",
which should work like "-cpu host" for KVM but like "cpu with all
implemented features" for TCG.
Move the place where we store the information about the host CPU from
a class object to static variables in kvm.c, and then in the instance
init function call a new kvm_arm_set_cpu_features_from_host()
function which will query the host kernel if necessary and then
fill in the CPU instance fields.
This allows us to drop the special class struct and class init
function for TYPE_ARM_HOST_CPU entirely.
We can't delay the probe until realize, because the ARM
instance_post_init hook needs to look at the feature bits we
set, so we need to do it in the initfn. This is safe because
the probing doesn't affect the actual VM state (it creates a
separate scratch VM to do its testing), but the probe might fail.
Because we can't report errors in retrieving the host features
in the initfn, we check this belatedly in the realize function
(the intervening code will be able to cope with the relevant
fields in the CPU structure being zero).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20180308130626.12393-2-peter.maydell@linaro.org
As an implementation choice, widening VL has zeroed the
previously inaccessible portion of the sve registers.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20180303143823.27055-2-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The cortex A53 TRM specifies that bits 24 and 25 of the L2CTLR register
specify the number of cores in the processor, not the total number of
cores in the system. To report this correctly on machines with multiple
CPU clusters (ARM's big.LITTLE or Xilinx's ZynqMP) we need to allow
the machine to overwrite this value. To do this let's add an optional
property.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: ef01d95c0759e88f47f22d11b14c91512a658b4f.1520018138.git.alistair.francis@xilinx.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Not enabled anywhere yet.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180228193125.20577-11-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Not enabled anywhere yet.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180228193125.20577-2-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Cortex-M33 allows the system to specify the reset value of the
secure Vector Table Offset Register (VTOR) by asserting config
signals. In particular, guest images for the MPS2 AN505 board rely
on the MPS2's initial VTOR being correct for that board.
Implement a QEMU property so board and SoC code can set the reset
value to the correct value.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180220180325.29818-7-peter.maydell@linaro.org
In v8M, the Implementation Defined Attribution Unit (IDAU) is
a small piece of hardware typically implemented in the SoC
which provides board or SoC specific security attribution
information for each address that the CPU performs MPU/SAU
checks on. For QEMU, we model this with a QOM interface which
is implemented by the board or SoC object and connected to
the CPU using a link property.
This commit defines the new interface class, adds the link
property to the CPU object, and makes the SAU checking
code call the IDAU interface if one is present.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180220180325.29818-5-peter.maydell@linaro.org
Half-precision flush to zero behaviour is controlled by a separate
FZ16 bit in the FPCR. To handle this we pass a pointer to
fp_status_fp16 when working on half-precision operations. The value of
the presented FPCR is calculated from an amalgam of the two when read.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180227143852.11175-5-alex.bennee@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180227143852.11175-4-alex.bennee@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180227143852.11175-3-alex.bennee@linaro.org
[PMM: postpone actually enabling feature until end of the
patch series]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
As cpu.h is another typically widely included file which doesn't need
full access to the softfloat API we can remove the includes from here
as well. Where they do need types it's typically for float_status and
the rounding modes so we move that to softfloat-types.h as well.
As a result of not having softfloat in every cpu.h call we now need to
add it to various helpers that do need the full softfloat.h
definitions.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
[For PPC parts]
Acked-by: David Gibson <david@gibson.dropbear.id.au>
The v8M architecture includes hardware support for enforcing
stack pointer limits. We don't implement this behaviour yet,
but provide the MSPLIM and PSPLIM stack pointer limit registers
as reads-as-written, so that when we do implement the checks
in future this won't break guest migration.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180209165810.6668-12-peter.maydell@linaro.org
We were previously making the system control register (SCR)
just RAZ/WI. Although we don't implement the functionality
this register controls, we should at least provide the state,
including the banked state for v8M.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180209165810.6668-7-peter.maydell@linaro.org
M profile cores have a similar setup for cache ID registers
to A profile:
* Cache Level ID Register (CLIDR) is a fixed value
* Cache Type Register (CTR) is a fixed value
* Cache Size ID Registers (CCSIDR) are a bank of registers;
which one you see is selected by the Cache Size Selection
Register (CSSELR)
The only difference is that they're in the NVIC memory mapped
register space rather than being coprocessor registers.
Implement the M profile view of them.
Since neither Cortex-M3 nor Cortex-M4 implement caches,
we don't need to update their init functions and can leave
the ctr/clidr/ccsidr[] fields in their ARMCPU structs at zero.
Newer cores (like the Cortex-M33) will want to be able to
set these ID registers to non-zero values, though.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180209165810.6668-6-peter.maydell@linaro.org
This also makes sure that we get the correct ordering of
SVE vs FP exceptions.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180211205848.4568-5-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180211205848.4568-3-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add both SVE exception state and vector length.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180123035349.24538-6-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180123035349.24538-3-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Change vfp.regs as a uint64_t to vfp.zregs as an ARMVectorReg.
The previous patches have made the change in representation
relatively painless.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180123035349.24538-2-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This implements emulation of the new SM4 instructions that have
been added as an optional extension to the ARMv8 Crypto Extensions
in ARM v8.2.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Message-id: 20180207111729.15737-5-ard.biesheuvel@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This implements emulation of the new SM3 instructions that have
been added as an optional extension to the ARMv8 Crypto Extensions
in ARM v8.2.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Message-id: 20180207111729.15737-4-ard.biesheuvel@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This implements emulation of the new SHA-3 instructions that have
been added as an optional extensions to the ARMv8 Crypto Extensions
in ARM v8.2.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Message-id: 20180207111729.15737-3-ard.biesheuvel@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This implements emulation of the new SHA-512 instructions that have
been added as an optional extensions to the ARMv8 Crypto Extensions
in ARM v8.2.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Message-id: 20180207111729.15737-2-ard.biesheuvel@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently armv7m_nvic_acknowledge_irq() does three things:
* make the current highest priority pending interrupt active
* return a bool indicating whether that interrupt is targeting
Secure or NonSecure state
* implicitly tell the caller which is the highest priority
pending interrupt by setting env->v7m.exception
We need to split these jobs, because v7m_exception_taken()
needs to know whether the pending interrupt targets Secure so
it can choose to stack callee-saves registers or not, but it
must not make the interrupt active until after it has done
that stacking, in case the stacking causes a derived exception.
Similarly, it needs to know the number of the pending interrupt
so it can read the correct vector table entry before the
interrupt is made active, because vector table reads might
also cause a derived exception.
Create a new armv7m_nvic_get_pending_irq_info() function which simply
returns information about the highest priority pending interrupt, and
use it to rearrange the v7m_exception_taken() code so we don't
acknowledge the exception until we've done all the things which could
possibly cause a derived exception.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1517324542-6607-3-git-send-email-peter.maydell@linaro.org
In order to support derived exceptions (exceptions generated in
the course of trying to take an exception), we need to be able
to handle prioritizing whether to take the original exception
or the derived exception.
We do this by introducing a new function
armv7m_nvic_set_pending_derived() which the exception-taking code in
helper.c will call when a derived exception occurs. Derived
exceptions are dealt with mostly like normal pending exceptions, so
we share the implementation with the armv7m_nvic_set_pending()
function.
Note that the way we structure this is significantly different
from the v8M Arm ARM pseudocode: that does all the prioritization
logic in the DerivedLateArrival() function, whereas we choose to
let the existing "identify highest priority exception" logic
do the prioritization for us. The effect is the same, though.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1517324542-6607-2-git-send-email-peter.maydell@linaro.org
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180119045438.28582-14-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Not enabled anywhere so far.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180119045438.28582-11-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Helpers that return a pointer into env->vfp.regs so that we isolate
the logic of how to index the regs array for different cpu modes.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180119045438.28582-7-richard.henderson@linaro.org
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
All direct users of this field want an integral value. Drop all
of the extra casting between uint64_t and float64.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180119045438.28582-6-richard.henderson@linaro.org
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The TT instruction is going to need to look up the MMU index
for a specified security and privilege state. Refactor the
existing arm_v7m_mmu_idx_for_secstate() into a version that
lets you specify the privilege state and one that uses the
current state of the CPU.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1512153879-5291-6-git-send-email-peter.maydell@linaro.org
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
For M profile, we currently have an mmu index MNegPri for
"requested execution priority negative". This fails to
distinguish "requested execution priority negative, privileged"
from "requested execution priority negative, usermode", but
the two can return different results for MPU lookups. Fix this
by splitting MNegPri into MNegPriPriv and MNegPriUser, and
similarly for the Secure equivalent MSNegPri.
This takes us from 6 M profile MMU modes to 8, which means
we need to bump NB_MMU_MODES; this is OK since the point
where we are forced to reduce TLB sizes is 9 MMU modes.
(It would in theory be possible to stick with 6 MMU indexes:
{mpu-disabled,user,privileged} x {secure,nonsecure} since
in the MPU-disabled case the result of an MPU lookup is
always the same for both user and privileged code. However
we would then need to rework the TB flags handling to put
user/priv into the TB flags separately from the mmuidx.
Adding an extra couple of mmu indexes is simpler.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1512153879-5291-5-git-send-email-peter.maydell@linaro.org
For the SG instruction and secure function return we are going
to want to do memory accesses using the MMU index of the CPU
in secure state, even though the CPU is currently in non-secure
state. Write arm_v7m_mmu_idx_for_secstate() to do this job,
and use it in cpu_mmu_index().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1506092407-26985-17-git-send-email-peter.maydell@linaro.org
In cpu_mmu_index() we try to do this:
if (env->v7m.secure) {
mmu_idx += ARMMMUIdx_MSUser;
}
but it will give the wrong answer, because ARMMMUIdx_MSUser
includes the 0x40 ARM_MMU_IDX_M field, and so does the
mmu_idx we're adding to, and we'll end up with 0x8n rather
than 0x4n. This error is then nullified by the call to
arm_to_core_mmu_idx() which masks out the high part, but
we're about to factor out the code that calculates the
ARMMMUIdx values so it can be used without passing it through
arm_to_core_mmu_idx(), so fix this bug first.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1506092407-26985-16-git-send-email-peter.maydell@linaro.org
Implement the register interface for the SAU: SAU_CTRL,
SAU_TYPE, SAU_RNR, SAU_RBAR and SAU_RLAR. None of the
actual behaviour is implemented here; registers just
read back as written.
When the CPU definition for Cortex-M33 is eventually
added, its initfn will set cpu->sau_sregion, in the same
way that we currently set cpu->pmsav7_dregion for the
M3 and M4.
Number of SAU regions is typically a configurable
CPU parameter, but this patch doesn't provide a
QEMU CPU property for it. We can easily add one when
we have a board that requires it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1506092407-26985-14-git-send-email-peter.maydell@linaro.org
Add the new M profile Secure Fault Status Register
and Secure Fault Address Register.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1506092407-26985-10-git-send-email-peter.maydell@linaro.org
In the v7M architecture, there is an invariant that if the CPU is
in Handler mode then the CONTROL.SPSEL bit cannot be nonzero.
This in turn means that the current stack pointer is always
indicated by CONTROL.SPSEL, even though Handler mode always uses
the Main stack pointer.
In v8M, this invariant is removed, and CONTROL.SPSEL may now
be nonzero in Handler mode (though Handler mode still always
uses the Main stack pointer). In preparation for this change,
change how we handle this bit: rename switch_v7m_sp() to
the now more accurate write_v7m_control_spsel(), and make it
check both the handler mode state and the SPSEL bit.
Note that this implicitly changes the point at which we switch
active SP on exception exit from before we pop the exception
frame to after it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1506092407-26985-4-git-send-email-peter.maydell@linaro.org
Update armv7m_nvic_acknowledge_irq() and armv7m_nvic_complete_irq()
to handle banked exceptions:
* acknowledge needs to use the correct vector, which may be
in sec_vectors[]
* acknowledge needs to return to its caller whether the
exception should be taken to secure or non-secure state
* complete needs its caller to tell it whether the exception
being completed is a secure one or not
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-20-git-send-email-peter.maydell@linaro.org
Now that we have a banked FAULTMASK register and banked exceptions,
we can implement the correct check in cpu_mmu_index() for whether
the MPU_CTRL.HFNMIENA bit's effect should apply. This bit causes
handlers which have requested a negative execution priority to run
with the MPU disabled. In v8M the test has to check this for the
current security state and so takes account of banking.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-17-git-send-email-peter.maydell@linaro.org
Make the armv7m_nvic_set_pending() and armv7m_nvic_clear_pending()
functions take a bool indicating whether to pend the secure
or non-secure version of a banked interrupt, and update the
callsites accordingly.
In most callsites we can simply pass the correct security
state in; in a couple of cases we use TODO comments to indicate
that we will return the code in a subsequent commit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-10-git-send-email-peter.maydell@linaro.org
The Application Interrupt and Reset Control Register has some changes
for v8M:
* new bits SYSRESETREQS, BFHFNMINS and PRIS: these all have
real state if the security extension is implemented and otherwise
are constant
* the PRIGROUP field is banked between security states
* non-secure code can be blocked from using the SYSRESET bit
to reset the system if SYSRESETREQS is set
Implement the new state and the changes to register read and write.
For the moment we ignore the effects of the secure PRIGROUP.
We will implement the effects of PRIS and BFHFNMIS later.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1505240046-11454-6-git-send-email-peter.maydell@linaro.org
there are 2 use cases to deal with:
1: fixed CPU models per board/soc
2: boards with user configurable cpu_model and fallback to
default cpu_model if user hasn't specified one explicitly
For the 1st
drop intermediate cpu_model parsing and use const cpu type
directly, which replaces:
typename = object_class_get_name(
cpu_class_by_name(TYPE_ARM_CPU, cpu_model))
object_new(typename)
with
object_new(FOO_CPU_TYPE_NAME)
or
cpu_generic_init(BASE_CPU_TYPE, "my cpu model")
with
cpu_create(FOO_CPU_TYPE_NAME)
as result 1st use case doesn't have to invoke not necessary
translation and not needed code is removed.
For the 2nd
1: set default cpu type with MachineClass::default_cpu_type and
2: use generic cpu_model parsing that done before machine_init()
is run and:
2.1: drop custom cpu_model parsing where pattern is:
typename = object_class_get_name(
cpu_class_by_name(TYPE_ARM_CPU, cpu_model))
[parse_features(typename, cpu_model, &err) ]
2.2: or replace cpu_generic_init() which does what
2.1 does + create_cpu(typename) with just
create_cpu(machine->cpu_type)
as result cpu_name -> cpu_type translation is done using
generic machine code one including parsing optional features
if supported/present (removes a bunch of duplicated cpu_model
parsing code) and default cpu type is defined in an uniform way
within machine_class_init callbacks instead of adhoc places
in boadr's machine_init code.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <1505318697-77161-6-git-send-email-imammedo@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Use a symbolic constant M_REG_NUM_BANKS for the array size for
registers which are banked by M profile security state, rather
than hardcoding lots of 2s.
Suggested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1505137930-13255-2-git-send-email-peter.maydell@linaro.org
This adds a feature bit indicating support of the (trivial) Jazelle
implementation if ARM_FEATURE_V6 is set or if the processor is arm926
or arm1026. This fixes the issue that any BXJ instruction will
result in an illegal_op. BXJ instructions will now check if the
architecture supports ARM_FEATURE_JAZELLE.
Signed-off-by: Portia Stephens <portia.stephens@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20170905211232.11092-1-portia.stephens@xilinx.com
[PMM: edited commit message and comment text a bit]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement the BXNS v8M instruction, which is like BX but will do a
jump-and-switch-to-NonSecure if the branch target address has bit 0
clear.
This is the first piece of code which implements "switch to the
other security state", so the commit also includes the code to
switch the stack pointers around, which is the only complicated
part of switching security state.
BLXNS is more complicated than just "BXNS but set the link register",
so we leave it for a separate commit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-21-git-send-email-peter.maydell@linaro.org
Make the CFSR register banked if v8M security extensions are enabled.
Not all the bits in this register are banked: the BFSR
bits [15:8] are shared between S and NS, and we store them
in the NS copy of the register.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-19-git-send-email-peter.maydell@linaro.org
Make the MMFAR register banked if v8M security extensions are
enabled.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-18-git-send-email-peter.maydell@linaro.org
Make the CCR register banked if v8M security extensions are enabled.
This is slightly more complicated than the other "add banking"
patches because there is one bit in the register which is not
banked. We keep the live data in the NS copy of the register,
and adjust it on register reads and writes. (Since we don't
currently implement the behaviour that the bit controls, there
is nowhere else that needs to care.)
This patch includes the enforcement of the bits which are newly
RES1 in ARMv8M.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1503414539-28762-17-git-send-email-peter.maydell@linaro.org
Make the MPU_CTRL register banked if v8M security extensions are
enabled.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-16-git-send-email-peter.maydell@linaro.org
Make the MPU_RNR register banked if v8M security extensions are
enabled.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-15-git-send-email-peter.maydell@linaro.org
Make the MPU registers MPU_MAIR0 and MPU_MAIR1 banked if v8M security
extensions are enabled.
We can freely add more items to vmstate_m_security without
breaking migration compatibility, because no CPU currently
has the ARM_FEATURE_M_SECURITY bit enabled and so this
subsection is not yet used by anything.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-14-git-send-email-peter.maydell@linaro.org
Make the MPU registers MPU_MAIR0 and MPU_MAIR1 banked if v8M security
extensions are enabled.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-13-git-send-email-peter.maydell@linaro.org
Make the VTOR register banked if v8M security extensions are enabled.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-12-git-send-email-peter.maydell@linaro.org
Make the CONTROL register banked if v8M security extensions are enabled.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-10-git-send-email-peter.maydell@linaro.org
Make the FAULTMASK register banked if v8M security extensions are enabled.
Note that we do not yet implement the functionality of the new
AIRCR.PRIS bit (which allows the effect of the NS copy of FAULTMASK to
be restricted).
This patch includes the code to determine for v8M which copy
of FAULTMASK should be updated on exception exit; further
changes will be required to the exception exit code in general
to support v8M, so this is just a small piece of that.
The v8M ARM ARM introduces a notation where individual paragraphs
are labelled with R (for rule) or I (for information) followed
by a random group of subscript letters. In comments where we want
to refer to a particular part of the manual we use this convention,
which should be more stable across document revisions than using
section or page numbers.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-9-git-send-email-peter.maydell@linaro.org
Richard Henderson
Peter Maydell
Alex Bennée
Dongjiu Geng
Aaron Lindsay
Julia Suvorova
Abdallah Bouassida
Igor Mammedov
Alistair Francis
Ard Biesheuvel
Portia Stephens