In the ARM ldr/str decode path, rather than directly testing
"insn & (1 << 21)" and "insn & (1 << 24)", abstract these
bits out into wbit and pbit local flags. (We will want to
do more tests against them to determine whether we need to
provide syndrome information.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
In BE32 mode, sub-word size watchpoints can fail to trigger because the
address of the access is adjusted in the opcode helpers before being
compared with the watchpoint registers. This patch reverses the address
adjustment before performing the comparison with the help of a new CPUClass
hook.
This version of the patch augments and tidies up comments a little.
Signed-off-by: Julian Brown <julian@codesourcery.com>
Message-id: caaf64ffc72f6ae183015337b7afdbd4b8989cb6.1484929304.git.julian@codesourcery.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Thumb-1 code has some issues in BE32 mode (as currently implemented). In
short, since bytes are swapped within words at load time for BE32
executables, this also swaps pairs of adjacent Thumb-1 instructions.
This patch un-swaps those pairs of instructions again, both for execution,
and for disassembly. (The previous version of the patch always read four
bytes in arm_read_memory_func and then extracted the proper two bytes,
in a probably misguided attempt to match the behaviour of actual hardware
as described by e.g. the ARM9TDMI TRM, section 3.3 "Endian effects for
instruction fetches". It's less complicated to just read the correct
two bytes though.)
Signed-off-by: Julian Brown <julian@codesourcery.com>
Message-id: ca20462a044848000370318a8bd41dd0a4ed273f.1484929304.git.julian@codesourcery.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a new "cfgend" property which selects whether the CPU resets into
big-endian mode or not. This setting affects whether we reset with
SCTLR_B (ARMv6 and earlier) or SCTLR_EE (ARMv7 and later) set.
Signed-off-by: Julian Brown <julian@codesourcery.com>
Message-id: 11420d1c49636c1790e60578ee996e51f0f0b835.1484929304.git.julian@codesourcery.com
[PMM: use error_report_err() rather than error_report();
move the integratorcp changes to their own patch;
drop an unnecessary extra #include;
rephrase commit message accordingly;
move setting of reset_sctlr above registration of cpregs
so it actually has an effect]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Since the integratorcp board creates the CPU object directly
rather than via cpu_arm_init(), we have to call the CPU
class parse_features() method ourselves if we want to
support the user passing features via the -cpu command
line argument as well as just the cpu name. Do so.
Signed-off-by: Julian Brown <julian@codesourcery.com>
[PMM: split out into its own patch]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
While doing multi block SDMA transfer in routine
'sdhci_sdma_transfer_multi_blocks', the 's->fifo_buffer' starting
index 'begin' and data length 's->data_count' could end up to be same.
This could lead to an OOB access issue. Correct transfer data length
to avoid it.
Cc: qemu-stable@nongnu.org
Reported-by: Jiang Xin <jiangxin1@huawei.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20170130064736.9236-1-ppandit@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This enables reboot of a guest from U-Boot and Linux.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 1485452251-1593-3-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Aspeed SoC includes a set of watchdog timers using 32-bit
decrement counters, which can be based either on the APB clock or
a 1 MHz clock.
The watchdog timer is designed to prevent system deadlock and, in
general, it should be restarted before timeout. When a timeout occurs,
different types of signals can be generated, ARM reset, SOC reset,
System reset, CPU Interrupt, external signal or boot from alternate
block. The current model only performs the system reset function as
this is used by U-Boot and Linux.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Message-id: 1485452251-1593-2-git-send-email-clg@kaod.org
[clg: - fixed compile breakage
- fixed io region size
- added watchdog_perform_action() on timer expiry
- wrote a commit log
- merged fixes from Andrew Jeffery to scale the reload value ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
VMState added by this patch preserves correct
loading of the integratorcp device state.
Signed-off-by: Pavel Dovgalyuk <pavel.dovgaluk@ispras.ru>
Message-id: 20170131114310.6768.79416.stgit@PASHA-ISP
[PMM: removed unnecessary minimum_version_id_old lines]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In
commit ba78db44f6
Author: Daniel P. Berrange <berrange@redhat.com>
Date: Wed Jan 25 16:14:10 2017 +0000
make: move top level dir to end of include search path
The dir $(BUILD_DIR)/$(@D) was added to the include
path. This would sometimes point to a non-existant
directory, if the sub-dir in question did not contain
any target-independant files (eg tcg/). To deal with
this the rules.mak attempted to create the directory.
While this was succesful, it also caused accidental
creation of files in the parent of the build dir.
e.g. when building common source files into target
specific output files.
Rather than trying to workaround this, just revert
the code that attempted to mkdir the missing include
directories. Instead just turn off the compiler warning
in question as the missing dir is expected & harmless
in general.
NB: you can clean up a build directory parent that has
been filled with empty directories by commit ba78db44f6
using this GNU find command in that parent directory:
find audio backends block chardev crypto disas fsdev hw io linux-user \
migration nbd net qapi qom replay slirp target ui util \
-type d -empty -delete
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Tested-by: Alberto Garcia <berto@igalia.com>
[PMM: added note about how to clean up a polluted directory]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
the correct UTS machine name (as expected by systemd) is "parisc",
not "hppa".
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20170126080449.28255-4-laurent@vivier.eu>
Signed-off-by: Richard Henderson <rth@twiddle.net>
apt-get was hanging on linux-user hppa.
strace has shown the netlink data stream was not correctly byte swapped.
It appears the fd translator function is unregistered just after it
has been registered, so the translator function is not called.
This patch removes the fd_trans_unregister() after the do_socket()
in the TARGET_NR_socket case.
This fd_trans_unregister() was added by commit
e36800c linux-user: add signalfd/signalfd4 syscalls
when do_socket() was not registering any fd translator.
And as now it is, we must remove this fd_trans_unregister() to keep them.
Reported-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Tested-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Message-Id: <20170126080449.28255-3-laurent@vivier.eu>
Signed-off-by: Richard Henderson <rth@twiddle.net>
As we have now a linux-user HPPA target, we can add it to the list of
supported targets in qemu-binfmt-conf.sh
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Message-Id: <20170126080449.28255-2-laurent@vivier.eu>
Signed-off-by: Richard Henderson <rth@twiddle.net>
An early postcopy failure can be recovered from as long as we know
we haven't sent the command to run the destination.
We have to undo the bdrv_inactivate_all by calling
bdrv_invalidate_cache_all
Note that I'm not using ms->block_inactive because once we've
sent the postcopy package we dont want anything else to try
and recover the block storage on the source; the destination
might have started writing to it.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20170202155909.31784-3-dgilbert@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
On a destination host with no userfault support an incoming
postcopy would cause the state to enter ADVISE before
it realised there was no support, and because it was in ADVISE
state it would perform a cleanup at the end. Since there
was no support the cleanup function should be unreachable,
but ends up being called and asserting.
Reset the state when we realise we have no support, thus the
cleanup doesn't happen.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20170202155909.31784-2-dgilbert@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Check qdev's call to vmstate_register_with_alias_id; that gets
most of the common uses; there's hundreds of calls via vmstate_register
which could get fixed over time.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20170202125956.21942-4-dgilbert@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
The qdev id of a device can be huge if it's on the end of a chain
of bridges; in reality such chains shouldn't occur but they can
be made to by chaining PCIe bridges together.
The migration format has a number of 256 character long format
limits; check we don't hit them (we already use pstrcat/cpy but
that just protects us from buffer overruns, we fairly quickly
hit an assert).
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20170202125956.21942-3-dgilbert@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
I'll be adding an error to it in a subsequent patch.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20170202125956.21942-2-dgilbert@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <1485207141-1941-3-git-send-email-quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
The qemu xhci emulation doesn't handle the ERDP_EHB flag correctly.
When the host adapter queues a new event the ERDP_EHB flag is set. The
flag is cleared (via w1c) by the guest when it updates the ERDP (event
ring dequeue pointer) register to notify the host adapter which events
it has fetched.
An IRQ must be raised in case the ERDP_EHB flag flips from clear to set.
If the flag is set already (which implies there are events queued up
which are not yet processed by the guest) xhci must *not* raise a IRQ.
Qemu got that wrong and raised an IRQ on every event, thereby generating
spurious interrupts in case we've queued events faster than the guest
processed them. This patch fixes that.
With that change in place we also have to check ERDP updates, to see
whenever the guest has fetched all queued events. In case there are
still pending events set ERDP_EHB and raise an IRQ again, to make sure
the events don't linger unseen forever.
The linux kernel driver and the microsoft windows driver (shipped with
win8+) can deal with the spurious interrupts without problems. The
renesas windows driver (v2.1.39) which can be used on older windows
versions is quite upset though. It does spurious ERDP updates now and
then (not every time, seems we must hit a race window for this to
happen), which in turn makes the qemu xhci emulation think the event
ring is full. Things go south from here ...
tl;dr: This is the "fix xhci on win7" patch.
Cc: M.Cerveny@computer.org
Cc: 1373228@bugs.launchpad.net
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 1486104705-13761-1-git-send-email-kraxel@redhat.com
This makes some cleanups that are a start on allowing ISA to be
compiled out for platforms which don't use it.
I posted this series last November, and it collected a number of R-bs
and no apparent objections. So, I've now rebased it (trivially) and
am sending a pull request in the hopes of merge. A lot of the pieces
here don't have a clear maintainer, so I'm sending it directly to
Peter.
Notes:
* Patch 3/3 triggers a style warning, but that's just because I'm
moving a C++ // comment verbatim from one file to another
Changes since v2:
* Trivial rebase
Changes since v1:
* Fixed some silly compile errors in 3/3 exposed by some
changes in other headers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=87oO
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/isa-cleanup-20170206' into staging
Allow ISA to be disabled on some platforms (v3)
This makes some cleanups that are a start on allowing ISA to be
compiled out for platforms which don't use it.
I posted this series last November, and it collected a number of R-bs
and no apparent objections. So, I've now rebased it (trivially) and
am sending a pull request in the hopes of merge. A lot of the pieces
here don't have a clear maintainer, so I'm sending it directly to
Peter.
Notes:
* Patch 3/3 triggers a style warning, but that's just because I'm
moving a C++ // comment verbatim from one file to another
Changes since v2:
* Trivial rebase
Changes since v1:
* Fixed some silly compile errors in 3/3 exposed by some
changes in other headers
# gpg: Signature made Mon 06 Feb 2017 01:37:50 GMT
# gpg: using RSA key 0x6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>"
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/isa-cleanup-20170206:
Split ISA and sysbus versions of m48t59 device
Allow ISA bus to be configured out
Split serial-isa into its own config option
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
CCID device emulator uses Application Protocol Data Units(APDU)
to exchange command and responses to and from the host.
The length in these units couldn't be greater than 65536. Add
check to ensure the same. It'd also avoid potential integer
overflow in emulated_apdu_from_guest.
Reported-by: Li Qiang <liqiang6-s@360.cn>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-id: 20170202192228.10847-1-ppandit@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
xhci_submit and xhci_fire_ctl_transfer are is called from
xhci_kick_epctx processing loop only, so there is no need to call
xhci_kick_epctx make sure processing continues. Also eecursive calls
into xhci_kick_epctx can cause trouble.
Drop the xhci_kick_epctx calls.
Cc: 1653384@bugs.launchpad.net
Fixes: 94b037f2a4
Reported-by: Fabian Lesniak <fabian@lesniak-it.de>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 1485790607-31399-4-git-send-email-kraxel@redhat.com
Make clear that this isn't guaranteed to actually complete the transfer,
the usb packet can still be in flight after calling that function.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 1485790607-31399-3-git-send-email-kraxel@redhat.com
Windows 10 reportedly sends these, so accept them in case
the device in question is a superspeed (usb3) device.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 1485870727-21956-2-git-send-email-kraxel@redhat.com
Print some more details in case we get a unknown
control request, to ease trouble-shooting.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 1485870727-21956-1-git-send-email-kraxel@redhat.com
1. Set bInterfaceProtocol to 0x00 for usb-tablet. This should be
non-zero for boot protocol devices only, which the usb-tablet is not.
2. Set the usb-tablet's usage to "mouse" in the report descriptor.
The boot protocol of 0x02 specifically confused OS X/macOS' HID driver
stack, causing it to generate additional bogus HID events with relative
motion in addition to the tablet's absolute coordinate events.
Absolute pointing devices with HID Report Descriptor usage of 0x01
(pointing) are treated by the macOS HID driver as analog sticks, and
absolute coordinates are not directly translated to absolute mouse
cursor positions. Changing it to 0x02 (mouse) fixes the problem, and
does not have any adverse effect in other operating systems and
windowing systems. (VMWare does the same thing.)
Signed-off-by: Phil Dennis-Jordan <phil@philjordan.eu>
Message-id: 1485365075-32702-1-git-send-email-phil@philjordan.eu
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The m48t59 device supports both ISA and direct sysbus attached versions of
the device in the one .c file. This can be awkward for some embedded
machine types which need the sysbus M48T59, but don't want to pull in the
ISA bus code and its other dependencies.
Therefore, this patch splits out the code for the ISA attached M48T59 into
its own C file. It will be built when both CONFIG_M48T59 and
CONFIG_ISA_BUS are enabled.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Currently, the code to handle the legacy ISA bus is always included in
qemu. However there are lots of platforms that don't include ISA legacy
devies, and quite a few that have never used ISA legacy devices at all.
This patch allows the ISA bus code to be disabled in the configuration for
platforms where it doesn't make sense.
For now, the default configs are adjusted to include ISA on all platforms
including PCI: anything with PCI can at least in principle add an i82378
PCI->ISA bridge. Also, CONFIG_IDE_CORE which is already in pci.mak
requires ISA support.
We also explicitly enable ISA on some other non-PCI platforms which include
ISA devices: moxie, sparc and unicore32. We may want to pare this down in
future.
The platforms that will lose ISA by default are: cris, lm32, microblazeel,
microblaze, openrisc, s390x, tricore, xtensaeb, xtensa. As far as I can
tell none of these ever used ISA.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
At present, the core device model code for 8250-like serial ports
(serial.c) and the code for serial ports attached to ISA-style legacy IO
(serial-isa.c) are both controlled by the CONFIG_SERIAL variable.
There are lots and lots of embedded platforms that have 8250-like serial
ports but have never had anything resembling ISA legacy IO. Therefore,
split serial-isa into its own CONFIG_SERIAL_ISA option so it can be
disabled for platforms where it's not appropriate.
For now, I enabled CONFIG_SERIAL_ISA in every default-config where
CONFIG_SERIAL is enabled, excepting microblaze, or32, and xtensa. As best
as I can tell, those platforms never used legacy ISA, and also don't
include PCI support (which would allow connection of a PCI->ISA bridge
and/or a southbridge including legacy ISA serial ports).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
IOThread AioContexts are likely to consist only of event sources like
virtqueue ioeventfds and LinuxAIO completion eventfds that are pollable
from userspace (without system calls).
We recently merged the AioContext polling feature but didn't enable it
by default yet. I have gone back over the performance data on the
mailing list and picked a default polling value that gave good results.
Let's enable AioContext polling by default so users don't have another
switch they need to set manually. If performance regressions are found
we can still disable this for the QEMU 2.9 release.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Karl Rister <krister@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20170126170119.27876-1-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
tb_jmp_insn_offset and tb_jmp_reset_offset are pointers
and cannot be used with ARRAY_SIZE.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 20170202195601.11286-1-sw@weilnetz.de
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This obsoletes ppc-for-2.9-20170112, which had a MacOS build bug.
This is a long overdue ppc pull request for qemu-2.9. It's been a
long time coming due to some holidays and inconveniently timed
problems with testing. So, there's a lot in here:
* More POWER9 instruction implementations for TCG
* The simpler parts of my CPU compatibility mode cleanup
* This changes behaviour to prefer compatibility modes over
"raW" mode for new machine type versions
* New "40p" machine type which is essentially a modernized and
cleaned up "prep". The intention is that it will replace "prep"
once it has some more testing and polish.
* Add pseries-2.9 machine type
* Implement H_SIGNAL_SYS_RESET hypercall
* Consolidate the two alternate CPU init paths in pseries by
making it always go through CPU core objects to initialize CPU
* A number of bugfixes and cleanups
* Stop the guest timebase when the guest is stopped under KVM.
This makes the guest system clock also stop when paused, which
matches the x86 behaviour.
* Some preliminary cleanups leading towards implementation of the
POWER9 MMU.
There are also some changes not strictly related to ppc code, but for
its benefit:
* Limit the pxi-expander-bridge (PXB) device to x86 guests only
(it's essentially a hack to work around historical x86
limitations)
* Some additions to the 128-bit math in host_utils, necessary for
some of the new instructions.
* Revise a number of qtests and enable them for ppc
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=vLVl
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-2.9-20170202' into staging
ppc patch queue 2017-02-02
This obsoletes ppc-for-2.9-20170112, which had a MacOS build bug.
This is a long overdue ppc pull request for qemu-2.9. It's been a
long time coming due to some holidays and inconveniently timed
problems with testing. So, there's a lot in here:
* More POWER9 instruction implementations for TCG
* The simpler parts of my CPU compatibility mode cleanup
* This changes behaviour to prefer compatibility modes over
"raW" mode for new machine type versions
* New "40p" machine type which is essentially a modernized and
cleaned up "prep". The intention is that it will replace "prep"
once it has some more testing and polish.
* Add pseries-2.9 machine type
* Implement H_SIGNAL_SYS_RESET hypercall
* Consolidate the two alternate CPU init paths in pseries by
making it always go through CPU core objects to initialize CPU
* A number of bugfixes and cleanups
* Stop the guest timebase when the guest is stopped under KVM.
This makes the guest system clock also stop when paused, which
matches the x86 behaviour.
* Some preliminary cleanups leading towards implementation of the
POWER9 MMU.
There are also some changes not strictly related to ppc code, but for
its benefit:
* Limit the pxi-expander-bridge (PXB) device to x86 guests only
(it's essentially a hack to work around historical x86
limitations)
* Some additions to the 128-bit math in host_utils, necessary for
some of the new instructions.
* Revise a number of qtests and enable them for ppc
# gpg: Signature made Thu 02 Feb 2017 01:40:16 GMT
# gpg: using RSA key 0x6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>"
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-2.9-20170202: (107 commits)
hw/ppc/pnv: Use error_report instead of hw_error if a ROM file can't be found
ppc/kvm: Handle the "family" CPU via alias instead of registering new types
target/ppc/mmu_hash64: Fix incorrect shift value in amr calculation
target/ppc/mmu_hash64: Fix printing unsigned as signed int
tcg/POWER9: NOOP the cp_abort instruction
target/ppc/debug: Print LPCR register value if register exists
target-ppc: Add xststdc[sp, dp, qp] instructions
target-ppc: Add xvtstdc[sp,dp] instructions
target-ppc: Add MMU model check for booke machines
ppc: switch to constants within BUILD_BUG_ON
target/ppc/cpu-models: Fix/remove bad CPU aliases
target/ppc: Remove unused POWERPC_FAMILY(POWER)
spapr: clock should count only if vm is running
ppc: Remove unused function cpu_ppc601_rtc_init()
target/ppc: Add pcr_supported to POWER9 cpu class definition
powerpc/cpu-models: rename ISAv3.00 logical PVR definition
target-ppc: Add xvcv[hpsp, sphp] instructions
target-ppc: Add xsmulqp instruction
target-ppc: Add xsdivqp instruction
target-ppc: Add xscvsdqp and xscvudqp instructions
...
# Conflicts:
# hw/pci-bridge/Makefile.objs
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The error exits of xen_pv_find_xendev() free the new xen-device via
g_free() which is wrong.
As the xen-device has been initialized as qdev it must be removed
via qdev_unplug().
This bug has been introduced with commit 3a6c9172ac
("xen: create qdev for each backend device").
Reported-by: Roger Pau Monné <roger.pau@citrix.com>
Tested-by: Roger Pau Monné <roger.pau@citrix.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
- build error with old gcc versions
- race between cmma reset and rom/loader resets
- linux-user vs. cpu model
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)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=hOry
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/borntraeger/tags/s390x-20170201' into staging
s390x fixes
- build error with old gcc versions
- race between cmma reset and rom/loader resets
- linux-user vs. cpu model
# gpg: Signature made Wed 01 Feb 2017 08:24:47 GMT
# gpg: using RSA key 0x117BBC80B5A61C7C
# gpg: Good signature from "Christian Borntraeger (IBM) <borntraeger@de.ibm.com>"
# Primary key fingerprint: F922 9381 A334 08F9 DBAB FBCA 117B BC80 B5A6 1C7C
* remotes/borntraeger/tags/s390x-20170201:
target/s390x: use "qemu" cpu model in user mode
s390x/kvm: fix small race reboot vs. cmma
s390-pci: fix compilation on older GCC versions
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When doing bitblt copy in backward mode, we should minus the
blt width first just like the adding in the forward mode. This
can avoid the oob access of the front of vga's vram.
Signed-off-by: Li Qiang <liqiang6-s@360.cn>
{ kraxel: with backward blits (negative pitch) addr is the topmost
address, so check it as-is against vram size ]
Cc: qemu-stable@nongnu.org
Cc: P J P <ppandit@redhat.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Wolfgang Bumiller <w.bumiller@proxmox.com>
Fixes: d3532a0db0 (CVE-2014-8106)
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 1485938101-26602-1-git-send-email-kraxel@redhat.com
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
generic pci root port support
disable shpc by default
safer version of ARRAY_SIZE and QEMU_BUILD_BUG_ON
fixes and cleanups all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYkTwaAAoJECgfDbjSjVRpHHoIALlEhk7iZJvjJBiT0BQ51lGB
uU0fq+8H2G+WZoM83dpSv/pG1Ob6SZtiehsXWf+6Za+AgnU3STCZDXGKo9Jxs2EO
jp73puewWCq69VMyjGnGEWWh4bf41xjWYVrhVrY9LSz7u6hCM9sdWPRy/PGLSlLo
s3xgYefGdtol0S5qMdb4LOb2tfcdGYHADyMiERT994pmfZKrBMXlHlVM0jOo5ytw
zknRh4JwH+zZMQPczrvWUTjdxRE0UIUd4fFz9cRwX8F6zVpAbKAT2Ird2jGNlpyh
jQBX+sxXQR3u+mjZDxZBYbpxOZARUTriagAJPs343uIUCPOmvVXsluidF9bkU+A=
=ZBEs
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
virtio, vhost, pci: fixes, features
generic pci root port support
disable shpc by default
safer version of ARRAY_SIZE and QEMU_BUILD_BUG_ON
fixes and cleanups all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Wed 01 Feb 2017 01:38:34 GMT
# gpg: using RSA key 0x281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (22 commits)
arm: add trailing ; after MISMATCH_CHECK
arm: better stub version for MISMATCH_CHECK
hw/pci: disable pci-bridge's shpc by default
vhost-user: delete chardev on cleanup
vhost: skip ROM sections
virtio: make virtio_should_notify static
pci: Convert msix_init() to Error and fix callers
hcd-xhci: check & correct param before using it
msix: Follow CODING_STYLE
hw/i386: check if nvdimm is enabled before plugging
hw/pcie: Introduce Generic PCI Express Root Port
hw/ioh3420: derive from PCI Express Root Port base class
hw/pcie: Introduce a base class for PCI Express Root Ports
intel_iommu: fix and simplify size calculation in process_device_iotlb_desc()
pci: mark ROMs read-only
ARRAY_SIZE: check that argument is an array
compiler: expression version of QEMU_BUILD_BUG_ON
compiler: rework BUG_ON using a struct
QEMU_BUILD_BUG_ON: use __COUNTER__
ppc: switch to constants within BUILD_BUG_ON
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>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=YkDp
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/elmarco/tags/chr-split-pull-request' into staging
# gpg: Signature made Tue 31 Jan 2017 19:32:40 GMT
# gpg: using RSA key 0xDAE8E10975969CE5
# gpg: Good signature from "Marc-André Lureau <marcandre.lureau@redhat.com>"
# gpg: aka "Marc-André Lureau <marcandre.lureau@gmail.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 87A9 BD93 3F87 C606 D276 F62D DAE8 E109 7596 9CE5
* remotes/elmarco/tags/chr-split-pull-request: (41 commits)
char: headers clean-up
char: move parallel chardev in its own file
char: move serial chardev to its own file
char: move pty chardev in its own file
char: move pipe chardev in its own file
char: move console in its own file
char: move stdio in its own file
char: move file chardev in its own file
char: move udp chardev in its own file
char: move socket chardev to its own file
char: move win-stdio into its own file
char: move win chardev base class in its own file
char: move fd chardev in its own file
char: move QIOChannel-related stuff to char-io.h
char: remove unused READ_RETRIES
char: rename and move to header CHR_READ_BUF_LEN
char: move ringbuf/memory to its own file
char: move mux to its own file
char: move null chardev to its own file
char: make null_chr_write() the default method
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>