Besides CMD12, the following command's reponse type is R1b:
- SET_WRITE_PROT (CMD28)
- CLR_WRITE_PROT (CMD29)
- ERASE (CMD38)
Reuse the same s->stopping to indicate a R1b reponse is needed.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210128063035.15674-10-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
CMD12's response type is R1b, which is basically a R1 plus optional
addition of the busy signal token that can be any number of bytes.
A zero value indicates card is busy and a non-zero value indicates
the card is ready for the next command.
Current implementation sends the busy signal token without sending
the R1 first. This does not break the U-Boot/Linux mmc_spi driver,
but it does not make the VxWorks driver happy.
Move the testing logic of s->stopping in the SSI_SD_RESPONSE state
a bit later, after the first byte of the card reponse is sent out,
to conform with the spec. After the busy signal token is sent, the
state should be transferred to SSI_SD_CMD.
Fixes: 775616c3ae ("Partial SD card SPI mode support")
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Message-Id: <20210128063035.15674-9-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The SEND_IF_COND command (CMD8) response is of format R7, but
current code returns R1 for CMD8. Fix it.
Fixes: 775616c3ae ("Partial SD card SPI mode support")
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210128063035.15674-8-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
For a multiple block write operation, each block begins with a multi
write start token. Unlike the SD mode that the multiple block write
ends when receiving a STOP_TRAN command (CMD12), a special stop tran
token is used to signal the card.
Emulating this by manually sending a CMD12 to the SD card core, to
bring it out of the receiving data state.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20210128063035.15674-7-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Add 2 more states for the block write operation. The SPI host needs
to send a data start token to start the transfer, and the data block
written to the card will be acknowledged by a data response token.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
[PMD: Change VMState version id 6 -> 7]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20210128063035.15674-6-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
In the case of a multiple block read operation every transferred
block has its suffix of CRC16. Update the state machine logic to
handle multiple block read.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
[PMD: Change VMState version id 5 -> 6]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20210128063035.15674-2-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
At present the codes use hardcoded numbers (0xff/0xfe) for the dummy
value and block start token. Replace them with macros.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210123104016.17485-12-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This fixes the wrong command index for STOP_TRANSMISSION, the
required command to interrupt the multiple block read command,
in the old codes. It should be CMD12 (0x4c), not CMD13 (0x4d).
Fixes: 775616c3ae ("Partial SD card SPI mode support")
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210123104016.17485-10-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Per the "Physical Layer Specification Version 8.00" chapter 7.5.2,
"Data Read", there is a minimum 8 clock cycles (Nac) after the card
response and before data block shows up on the data out line. This
applies to both single and multiple block read operations.
Current implementation of single block read already satisfies the
timing requirement as in the RESPONSE state after all responses are
transferred the state remains unchanged. In the next 8 clock cycles
it jumps to DATA_START state if data is ready.
However we need an explicit state when expanding our support to
multiple block read in the future. Let's add a new state PREP_DATA
explicitly in the ssi-sd state machine to represent Nac.
Note we don't change the single block read state machine to let it
jump from RESPONSE state to DATA_START state as that effectively
generates a 16 clock cycles Nac, which might not be safe. As the
spec says the maximum Nac shall be calculated from several fields
encoded in the CSD register, we don't want to bother updating CSD
to ensure our Nac is within range to complicate things.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210123104016.17485-9-bmeng.cn@gmail.com>
[PMD: Change VMState version id 4 -> 5]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Per the SD spec, a valid data block is suffixed with a 16-bit CRC
generated by the standard CCITT polynomial x16+x12+x5+1. This part
is currently missing in the ssi-sd state machine. Without it, all
data block transfer fails in guest software because the expected
CRC16 is missing on the data out line.
Fixes: 775616c3ae ("Partial SD card SPI mode support")
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210123104016.17485-8-bmeng.cn@gmail.com>
[PMD: Change VMState version id 3 -> 4,
check s->mode validity in post_load()]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Per the "Physical Layer Specification Version 8.00" chapter 7.5.1,
"Command/Response", there is a minimum 8 clock cycles (Ncr) before
the card response shows up on the data out line. However current
implementation jumps directly to the sending response state after
all 6 bytes command is received, which is a spec violation.
Add a new state PREP_RESP in the ssi-sd state machine to handle it.
Fixes: 775616c3ae ("Partial SD card SPI mode support")
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210123104016.17485-4-bmeng.cn@gmail.com>
[PMD: Change VMState version id 2 -> 3]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
In order to use inclusive terminology, rename SSI 'slave' as
'peripheral', following the specification resolution:
https://www.oshwa.org/a-resolution-to-redefine-spi-signal-names/
Patch created mechanically using:
$ sed -i s/SSISlave/SSIPeripheral/ $(git grep -l SSISlave)
$ sed -i s/SSI_SLAVE/SSI_PERIPHERAL/ $(git grep -l SSI_SLAVE)
$ sed -i s/ssi-slave/ssi-peripheral/ $(git grep -l ssi-slave)
$ sed -i s/ssi_slave/ssi_peripheral/ $(git grep -l ssi_slave)
$ sed -i s/ssi_create_slave/ssi_create_peripheral/ \
$(git grep -l ssi_create_slave)
Then in VMStateDescription vmstate_ssi_peripheral we restored
the "SSISlave" migration stream name (to avoid breaking migration).
Finally the following files have been manually tweaked:
- hw/ssi/pl022.c
- hw/ssi/xilinx_spips.c
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201012124955.3409127-4-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Some typedefs and macros are defined after the type check macros.
This makes it difficult to automatically replace their
definitions with OBJECT_DECLARE_TYPE.
Patch generated using:
$ ./scripts/codeconverter/converter.py -i \
--pattern=QOMStructTypedefSplit $(git grep -l '' -- '*.[ch]')
which will split "typdef struct { ... } TypedefName"
declarations.
Followed by:
$ ./scripts/codeconverter/converter.py -i --pattern=MoveSymbols \
$(git grep -l '' -- '*.[ch]')
which will:
- move the typedefs and #defines above the type check macros
- add missing #include "qom/object.h" lines if necessary
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-9-ehabkost@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-10-ehabkost@redhat.com>
Message-Id: <20200831210740.126168-11-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The sdbus_read_data() method do a single byte access on the data
line of a SD bus. Rename it as sdbus_read_byte() and document it.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20200814092346.21825-4-f4bug@amsat.org>
If we want to check error after errp-function call, we need to
introduce local_err and then propagate it to errp. Instead, use
the ERRP_GUARD() macro, benefits are:
1. No need of explicit error_propagate call
2. No need of explicit local_err variable: use errp directly
3. ERRP_GUARD() leaves errp as is if it's not NULL or
&error_fatal, this means that we don't break error_abort
(we'll abort on error_set, not on error_propagate)
If we want to add some info to errp (by error_prepend() or
error_append_hint()), we must use the ERRP_GUARD() macro.
Otherwise, this info will not be added when errp == &error_fatal
(the program will exit prior to the error_append_hint() or
error_prepend() call). No such cases are being fixed here.
This commit is generated by command
sed -n '/^SD (Secure Card)$/,/^$/{s/^F: //p}' \
MAINTAINERS | \
xargs git ls-files | grep '\.[hc]$' | \
xargs spatch \
--sp-file scripts/coccinelle/errp-guard.cocci \
--macro-file scripts/cocci-macro-file.h \
--in-place --no-show-diff --max-width 80
Reported-by: Kevin Wolf <kwolf@redhat.com>
Reported-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[Commit message tweaked]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20200707165037.1026246-4-armbru@redhat.com>
[ERRP_AUTO_PROPAGATE() renamed to ERRP_GUARD(), and
auto-propagated-errp.cocci to errp-guard.cocci. Commit message
tweaked again.]
The previous commit enables conversion of
qdev_prop_set_drive_err(..., &err);
if (err) {
...
}
to
if (!qdev_prop_set_drive_err(..., errp)) {
...
}
Coccinelle script:
@@
identifier fun = qdev_prop_set_drive_err;
expression list args;
typedef Error;
Error *err;
@@
- fun(args, &err);
- if (err)
+ if (!fun(args, &err))
{
...
}
One line break tidied up manually.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20200707160613.848843-33-armbru@redhat.com>
The previous commit enables conversion of
foo(..., &err);
if (err) {
...
}
to
if (!foo(..., errp)) {
...
}
for QOM functions that now return true / false on success / error.
Coccinelle script:
@@
identifier fun = {
object_apply_global_props, object_initialize_child_with_props,
object_initialize_child_with_propsv, object_property_get,
object_property_get_bool, object_property_parse, object_property_set,
object_property_set_bool, object_property_set_int,
object_property_set_link, object_property_set_qobject,
object_property_set_str, object_property_set_uint, object_set_props,
object_set_propv, user_creatable_add_dict,
user_creatable_complete, user_creatable_del
};
expression list args, args2;
typedef Error;
Error *err;
@@
- fun(args, &err, args2);
- if (err)
+ if (!fun(args, &err, args2))
{
...
}
Fails to convert hw/arm/armsse.c, because Coccinelle gets confused by
ARMSSE being used both as typedef and function-like macro there.
Convert manually.
Line breaks tidied up manually.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20200707160613.848843-29-armbru@redhat.com>
The object_property_set_FOO() setters take property name and value in
an unusual order:
void object_property_set_FOO(Object *obj, FOO_TYPE value,
const char *name, Error **errp)
Having to pass value before name feels grating. Swap them.
Same for object_property_set(), object_property_get(), and
object_property_parse().
Convert callers with this Coccinelle script:
@@
identifier fun = {
object_property_get, object_property_parse, object_property_set_str,
object_property_set_link, object_property_set_bool,
object_property_set_int, object_property_set_uint, object_property_set,
object_property_set_qobject
};
expression obj, v, name, errp;
@@
- fun(obj, v, name, errp)
+ fun(obj, name, v, errp)
Chokes on hw/arm/musicpal.c's lcd_refresh() with the unhelpful error
message "no position information". Convert that one manually.
Fails to convert hw/arm/armsse.c, because Coccinelle gets confused by
ARMSSE being used both as typedef and function-like macro there.
Convert manually.
Fails to convert hw/rx/rx-gdbsim.c, because Coccinelle gets confused
by RXCPU being used both as typedef and function-like macro there.
Convert manually. The other files using RXCPU that way don't need
conversion.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20200707160613.848843-27-armbru@redhat.com>
[Straightforwad conflict with commit 2336172d9b "audio: set default
value for pcspk.iobase property" resolved]
Convert
foo(..., &err);
if (err) {
...
}
to
if (!foo(..., &err)) {
...
}
for qdev_realize(), qdev_realize_and_unref(), qbus_realize() and their
wrappers isa_realize_and_unref(), pci_realize_and_unref(),
sysbus_realize(), sysbus_realize_and_unref(), usb_realize_and_unref().
Coccinelle script:
@@
identifier fun = {
isa_realize_and_unref, pci_realize_and_unref, qbus_realize,
qdev_realize, qdev_realize_and_unref, sysbus_realize,
sysbus_realize_and_unref, usb_realize_and_unref
};
expression list args, args2;
typedef Error;
Error *err;
@@
- fun(args, &err, args2);
- if (err)
+ if (!fun(args, &err, args2))
{
...
}
Chokes on hw/arm/musicpal.c's lcd_refresh() with the unhelpful error
message "no position information". Nothing to convert there; skipped.
Fails to convert hw/arm/armsse.c, because Coccinelle gets confused by
ARMSSE being used both as typedef and function-like macro there.
Converted manually.
A few line breaks tidied up manually.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-Id: <20200707160613.848843-5-armbru@redhat.com>
The FROM_SSI_SLAVE() macro predates QOM and is used as a typesafe way
to cast from an SSISlave* to the instance struct of a subtype of
TYPE_SSI_SLAVE. Switch to using the QOM cast macros instead, which
have the same effect (by writing the QOM macros if the types were
previously missing them.)
(The FROM_SSI_SLAVE() macro allows the SSISlave member of the
subtype's struct to be anywhere as long as it is named "ssidev",
whereas a QOM cast macro insists that it is the first thing in the
subtype's struct. This is true for all the types we convert here.)
This removes all the uses of FROM_SSI_SLAVE() so we can delete the
definition.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20200628142429.17111-18-peter.maydell@linaro.org
qdev_prop_set_drive() can fail. None of the other qdev_prop_set_FOO()
can; they abort on error.
To clean up this inconsistency, rename qdev_prop_set_drive() to
qdev_prop_set_drive_err(), and create a qdev_prop_set_drive() that
aborts on error.
Coccinelle script to update callers:
@ depends on !(file in "hw/core/qdev-properties-system.c")@
expression dev, name, value;
symbol error_abort;
@@
- qdev_prop_set_drive(dev, name, value, &error_abort);
+ qdev_prop_set_drive(dev, name, value);
@@
expression dev, name, value, errp;
@@
- qdev_prop_set_drive(dev, name, value, errp);
+ qdev_prop_set_drive_err(dev, name, value, errp);
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200622094227.1271650-14-armbru@redhat.com>
This is the transformation explained in the commit before previous.
Takes care of just one pattern that needs conversion. More to come in
this series.
Coccinelle script:
@ depends on !(file in "hw/arm/highbank.c")@
expression bus, type_name, dev, expr;
@@
- dev = qdev_create(bus, type_name);
+ dev = qdev_new(type_name);
... when != dev = expr
- qdev_init_nofail(dev);
+ qdev_realize_and_unref(dev, bus, &error_fatal);
@@
expression bus, type_name, dev, expr;
identifier DOWN;
@@
- dev = DOWN(qdev_create(bus, type_name));
+ dev = DOWN(qdev_new(type_name));
... when != dev = expr
- qdev_init_nofail(DEVICE(dev));
+ qdev_realize_and_unref(DEVICE(dev), bus, &error_fatal);
@@
expression bus, type_name, expr;
identifier dev;
@@
- DeviceState *dev = qdev_create(bus, type_name);
+ DeviceState *dev = qdev_new(type_name);
... when != dev = expr
- qdev_init_nofail(dev);
+ qdev_realize_and_unref(dev, bus, &error_fatal);
@@
expression bus, type_name, dev, expr, errp;
symbol true;
@@
- dev = qdev_create(bus, type_name);
+ dev = qdev_new(type_name);
... when != dev = expr
- object_property_set_bool(OBJECT(dev), true, "realized", errp);
+ qdev_realize_and_unref(dev, bus, errp);
@@
expression bus, type_name, expr, errp;
identifier dev;
symbol true;
@@
- DeviceState *dev = qdev_create(bus, type_name);
+ DeviceState *dev = qdev_new(type_name);
... when != dev = expr
- object_property_set_bool(OBJECT(dev), true, "realized", errp);
+ qdev_realize_and_unref(dev, bus, errp);
The first rule exempts hw/arm/highbank.c, because it matches along two
control flow paths there, with different @type_name. Covered by the
next commit's manual conversions.
Missing #include "qapi/error.h" added manually.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-10-armbru@redhat.com>
[Conflicts in hw/misc/empty_slot.c and hw/sparc/leon3.c resolved]
It's wrong to use same err object as errp parameter for several
function calls without intermediate checking for error: we'll crash if
try to set err object twice. Fix that.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20200317125741.15301-1-vsementsov@virtuozzo.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
In my "build everything" tree, changing hw/qdev-properties.h triggers
a recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
Many places including hw/qdev-properties.h (directly or via hw/qdev.h)
actually need only hw/qdev-core.h. Include hw/qdev-core.h there
instead.
hw/qdev.h is actually pointless: all it does is include hw/qdev-core.h
and hw/qdev-properties.h, which in turn includes hw/qdev-core.h.
Replace the remaining uses of hw/qdev.h by hw/qdev-properties.h.
While there, delete a few superfluous inclusions of hw/qdev-core.h.
Touching hw/qdev-properties.h now recompiles some 1200 objects.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Daniel P. Berrangé" <berrange@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190812052359.30071-22-armbru@redhat.com>
In my "build everything" tree, changing migration/vmstate.h triggers a
recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get VMStateDescription. The previous commit made
that unnecessary.
Include migration/vmstate.h only where it's still needed. Touching it
now recompiles only some 1600 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-16-armbru@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Rather than looking inside the definition of a BusState with "s->bus.qbus",
use the QOM prefered style: "BUS(&s->bus)".
This patch was generated using the following Coccinelle script:
// Use BUS() macros to access BusState.qbus
@use_bus_macro_to_access_qbus@
expression obj;
identifier bus;
@@
-&obj->bus.qbus
+BUS(&obj->bus)
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20190528164020.32250-6-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Device models aren't supposed to go on fishing expeditions for
backends. They should expose suitable properties for the user to set.
For onboard devices, board code sets them.
Device ssi-sd picks up its block backend in its init() method with
drive_get_next() instead. This mistake is already marked FIXME since
commit af9e40a.
Unset user_creatable to remove the mistake from our external
interface. Since the SSI bus doesn't support hotplug, only -device
can be affected. Only certain ARM machines have ssi-sd and provide an
SSI bus for it; this patch breaks -device ssi-sd for these machines.
No actual use of -device ssi-sd is known.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Thomas Huth <thuth@redhat.com>
Message-id: 20181009060835.4608-1-armbru@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The load/store API will ease further code movement.
Per the Physical Layer Simplified Spec. "3.6 Bus Protocol":
"In the CMD line the Most Significant Bit (MSB) is transmitted
first, the Least Significant Bit (LSB) is the last."
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Remove those unneeded includes to speed up the compilation
process a little bit. (Continue 7eceff5b5a cleanup)
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180528232719.4721-13-f4bug@amsat.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
On reset the bus will reset the card,
we can now drop the device_reset() call.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180216022933.10945-5-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Since ssi-sd is still using the legacy SD card API, the SD
card created by sd_init() is not plugged into any bus. This
means that the controller has to reset it manually.
Failing to do this mostly didn't affect the guest since the
guest typically does a programmed SD card reset as part of
its SD controller driver initialization, but meant that
migration failed because it's only in sd_reset() that we
set up the wpgrps_size field.
In the case of sd-ssi, we have to implement an entire
reset function since there wasn't one previously, and
that requires a QOM cast macro that got omitted when this
device was QOMified.
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1515506513-31961-4-git-send-email-peter.maydell@linaro.org
Changed a few types to fixed sized types in the ssi_sd_state
Now saving/loading a byte for the cmdarg/response bytes that were
previously saved as uint32
Bumped version number to deal with those changes.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-id: 1472035246-12483-4-git-send-email-dgilbert@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This enables qemu to handle late inits and report errors. All the SSI
slave routine names were changed accordingly. Code was modified to
handle errors when possible (m25p80 and ssi-sd)
Tested with the m25p80 slave object.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1467138270-32481-2-git-send-email-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-38-git-send-email-peter.maydell@linaro.org
Move the ssi.h include file into the ssi directory.
While touching the code also fix the typdef lines as
checkpatch complains.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Create a sd directory under include/hw/ and move sd.h to
include/hw/sd/
Signed-off-by: Sai Pavan Boddu <saipava@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Drives defined with if!=none are for board initialization to wire up.
Board code calls drive_get() or similar to find them, and creates
devices with their qdev drive properties set accordingly.
Except a few devices go on a fishing expedition for a suitable backend
instead of exposing a drive property for board code to set: they call
driver_get() or drive_get_next() in their realize() or init() method
to implicitly connect to the "next" backend with a certain interface
type.
Picking up backends that way works when the devices are created by
board code. But it's inappropriate for -device or device_add. Not
only is this inconsistent with how the other block device models work
(they connect to a backend explicitly identified by a "drive"
property), it breaks when the "next" backend has been picked up by the
board already.
Example:
$ qemu-system-arm -S -M connex -pflash flash.img -device ssi-sd
Aborted (core dumped)
Mark them with suitable FIXME comments.
Cc: Andrzej Zaborowski <balrogg@gmail.com>
Cc: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Cc: "Andreas Färber" <andreas.faerber@web.de>
Cc: Michael Walle <michael@walle.cc>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Device models should access their block backends only through the
block-backend.h API. Convert them, and drop direct includes of
inappropriate headers.
Just four uses of BlockDriverState are left:
* The Xen paravirtual block device backend (xen_disk.c) opens images
itself when set up via xenbus, bypassing blockdev.c. I figure it
should go through qmp_blockdev_add() instead.
* Device model "usb-storage" prompts for keys. No other device model
does, and this one probably shouldn't do it, either.
* ide_issue_trim_cb() uses bdrv_aio_discard() instead of
blk_aio_discard() because it fishes its backend out of a BlockAIOCB,
which has only the BlockDriverState.
* PC87312State has an unused BlockDriverState[] member.
The next two commits take care of the latter two.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The patch is big, but all it really does is replacing
dinfo->bdrv
by
blk_bs(blk_by_legacy_dinfo(dinfo))
The replacement is repetitive, but the conversion of device models to
BlockBackend is imminent, and will shorten it to just
blk_legacy_dinfo(dinfo).
Line wrapping muddies the waters a bit. I also omit tests whether
dinfo->bdrv is null, because it never is.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Benoît Canet <benoit.canet@nodalink.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
CVE-2013-4537
s->arglen is taken from wire and used as idx
in ssi_sd_transfer().
Validate it before access.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Convert legacy ->qdev style casts from TYPE_SSI_SLAVE to TYPE_DEVICE.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
[AF: Introduce local DeviceState variable for transition to QOM realize]
Signed-off-by: Andreas Färber <afaerber@suse.de>
IF_NONE allows read-only, which makes forbidding it in this place
for other types pretty much pointless.
Instead, make sure that all devices for which the check would have
errored out check in their init function that they don't get a read-only
BlockDriverState. This catches even cases where IF_NONE and -device is
used.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
