The register index is currently printed and this is confusing.
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Message-Id: <20211005052604.1674891-3-pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This model implements enough behaviour to do basic functionality tests
such as device initialisation and read out of dummy sample values. The
sample value generation strategy is similar to the STM ADC already in
the tree.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
[clg : support for multiple engines (AST2600) ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
[pdel : refactored engine register struct fields to regs[] array field]
[pdel : added guest-error checking for upper-8 channel regs in AST2600]
[pdel : allow 16-bit reads of the channel data registers]
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Message-Id: <20211005052604.1674891-2-pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The gpio array is declared as a dense array:
qemu_irq gpios[ASPEED_GPIO_NR_PINS];
(AST2500 has 228, AST2400 has 216, AST2600 has 208)
However, this array is used like a matrix of GPIO sets
(e.g. gpio[NR_SETS][NR_PINS_PER_SET] = gpio[8][32])
size_t offset = set * GPIOS_PER_SET + gpio;
qemu_set_irq(s->gpios[offset], !!(new & mask));
This can result in an out-of-bounds access to "s->gpios" because the
gpio sets do _not_ have the same length. Some of the groups (e.g.
GPIOAB) only have 4 pins. 228 != 8 * 32 == 256.
To fix this, I converted the gpio array from dense to sparse, to that
match both the hardware layout and this existing indexing code.
Fixes: 4b7f956862 ("hw/gpio: Add basic Aspeed GPIO model for AST2400 and AST2500")
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Message-Id: <20211008033501.934729-2-pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Some of the pin declarations in the Aspeed GPIO module were incorrect,
probably because of confusion over which bits in the input and output
uint32_t's correspond to which groups in the label array. Since the
uint32_t literals are in big endian, it's sort of the opposite of what
would be intuitive. The least significant bit in ast2500_set_props[6]
corresponds to GPIOY0, not GPIOAB7.
GPIOxx indicates input and output capabilities, GPIxx indicates only
input, GPOxx indicates only output.
AST2500:
- Previously had GPIW0..GPIW7 and GPIX0..GPIX7, that's correct.
- Previously had GPIOY0..GPIOY3, should have been GPIOY0..GPIOY7.
- Previously had GPIOAB0..GPIOAB3 and GPIAB4..GPIAB7, should only have
been GPIOAB0..GPIOAB3.
AST2600:
- GPIOT0..GPIOT7 should have been GPIT0..GPIT7.
- GPIOU0..GPIOU7 should have been GPIU0..GPIU7.
- GPIW0..GPIW7 should have been GPIOW0..GPIOW7.
- GPIOY0..GPIOY7 and GPIOZ0...GPIOZ7 were disabled.
Fixes: 4b7f956862 ("hw/gpio: Add basic Aspeed GPIO model for AST2400 and AST2500")
Fixes: 36d737ee82 ("hw/gpio: Add in AST2600 specific implementation")
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Damien Hedde <damien.hedde@greensocs.com>
Reviewed-by: Rashmica Gupta <rashmica.g@gmail.com>
Message-Id: <20210928032456.3192603-2-pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Introduce an AspeedI2CBus SysBusDevice model and attach the associated
memory region and IRQ to the newly instantiated objects.
Before this change, the I2C bus IRQs were all attached to the
SysBusDevice model of the I2C controller. Adapt the AST2600 SoC
realize routine to take into account this change.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The AST2400 SPI controller has a transitional HW interface and it
stores the address width currently in use in a different register than
all the other SMC controllers. It needs special handling when working
in 4B mode.
Make it clear through a class handler. This also removes another use
of the segments array.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This simplifies the reset handler and has the benefit to remove some
"bad" use of the segments array as an identifier of the controller model.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
AspeedSMCFlash is a small structure representing the AHB memory window
through which the contents of a flash device can be accessed with MMIOs.
Introduce an AspeedSMCFlash SysBusDevice model and attach the associated
memory region to the newly instantiated objects.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
'cs' is a more appropriate name to index SPI flash devices.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
AspeedSMCFlash::size is only used to compute the initial size of the
boot_rom region. Not very useful, so directly call memory_region_size()
instead.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
There is no need to keep a reference of the flash qdev in the AspeedSMCFlash
state: the SPI bus takes ownership and will release its resources. Remove
AspeedSMCFlash::flash.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The characteristics of the Aspeed controllers are described in a
AspeedSMCController structure which is redundant with the
AspeedSMCClass. Move all attributes under the class and adapt the code
to use class attributes instead.
This is a large change but it is functionally equivalent.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
There is no real reason to use this name. It's simply nice to have in
the monitor output but it's a burden for the following patch which
removes the AspeedSMCController structure describing the controller.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
It unifies the errors reported by the Aspeed SMC model and also
removes some use of ctrl->name which will help us for the next
patches.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The Aspeed SoCs have a dual boot function for firmware fail-over
recovery. The system auto-reboots from the second flash if the main
flash does not boot successfully within a certain amount of time. This
function is called alternate boot (ABR) in the FMC controllers.
On AST2400/AST2500, ABR is enabled by hardware strapping in SCU70 to
enable the 2nd watchdog timer, on AST2600, through register SCU510.
If the boot on the the main flash succeeds, the firmware should
disable the 2nd watchdog timer. If not, the BMC is reset and the CE0
and CE1 mappings are swapped to restart the BMC from the 2nd flash.
On the AST2600, the ABR registers controlling the 2nd watchdog timer
were moved from the watchdog register to the FMC controller and the
FMC model should be able to control WDT2 through its own register set.
This requires more work. For now, add dummy read/write handlers to let
the FW disable the 2nd watchdog without error.
Reviewed-by: Peter Delevoryas <pdel@fb.com>
Reported-by: Peter Delevoryas <pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Whilst the in-built Quadra 800 framebuffer exists within the Nubus address
space for slot 9, it has its own dedicated interrupt on VIA2. Force the
macfb device to occupy slot 9 in the q800 machine and wire its IRQ to the
separate video interrupt since this is what is expected by the MacOS
interrupt handler.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20211007221253.29024-14-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The MacOS driver expects a 60.15Hz vertical blank interrupt to be generated by
the framebuffer which in turn schedules the mouse driver via the Vertical Retrace
Manager.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20211007221253.29024-13-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
According to Apple Technical Note HW26: "Macintosh Quadra Built-In Video" the
in-built framebuffer encodes each 24-bit pixel into 4 bytes. Adjust the 24-bit
RGB pixel encoding accordingly which agrees with the encoding expected by MacOS
when changing into 24-bit colour mode.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20211007221253.29024-12-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The MacOS driver expects the RGB values for the pixel to be in entries 0 and 1
of the colour palette.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20211007221253.29024-11-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The monitor modes table is found by experimenting with the Monitors Control
Panel in MacOS and analysing the reads/writes. From this it can be found that
the mode is controlled by writes to the DAFB_MODE_CTRL1 and DAFB_MODE_CTRL2
registers.
Implement the first block of DAFB registers as a register array including the
existing sense register, the newly discovered control registers above, and also
the DAFB_MODE_VADDR1 and DAFB_MODE_VADDR2 registers which are used by NetBSD to
determine the current video mode.
These experiments also show that the offset of the start of video RAM and the
stride can change depending upon the monitor mode, so update macfb_draw_graphic()
and both the BI_MAC_VADDR and BI_MAC_VROW bootinfo for the q800 machine
accordingly.
Finally update macfb_common_realize() so that only the resolution and depth
supported by the display type can be specified on the command line, and add an
error hint showing the list of supported resolutions and depths if the user tries
to specify an invalid display mode.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20211007221253.29024-10-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Since the available resolutions and colour depths are determined by the attached
display type, add a qdev property to allow the display type to be specified.
The main resolutions of interest are high resolution 1152x870 with 8-bit colour
and SVGA resolution up to 800x600 with 24-bit colour so update the q800 machine
to allow high resolution mode if specified and otherwise fall back to SVGA.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20211007221253.29024-9-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The MacOS toolbox ROM uses the monitor sense to detect the display type and then
offer a fixed set of resolutions and colour depths accordingly. Implement the
monitor sense using information found in Apple Technical Note HW26: "Macintosh
Quadra Built-In Video" along with some local experiments.
Since the default configuration is 640 x 480 with 8-bit colour then hardcode
the sense register to return MACFB_DISPLAY_VGA for now.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20211007221253.29024-8-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Currently macfb_common_realize() defines the framebuffer RAM memory region as
being non-migrateable but then immediately registers it for migration. Replace
memory_region_init_ram_nomigrate() with memory_region_init_ram() which is clearer
and does exactly the same thing.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20211007221253.29024-6-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The palette_current index counter has a maximum size of 256 * 3 to cover a full
color palette of 256 RGB entries. Linux assumes that the palette_current index
wraps back around to zero after writing 256 RGB entries so ensure that
palette_current is reset at this point to prevent data corruption within
MacfbState.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20211007221253.29024-5-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
During realize memory_region_init_ram_nomigrate() is used to initialise the RAM
memory region used for the framebuffer but the owner object reference is
incorrect since MacFbState is a typedef and not a QOM type.
Change the memory region owner to be the corresponding DeviceState to fix the
issue and prevent random crashes during macfb_common_realize().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Fixes: 8ac919a065 ("hw/m68k: add Nubus macfb video card")
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20211007221253.29024-4-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
As per the current Error API best practices, change macfb_commom_realize() to return
a boolean indicating success to reduce errp boiler-plate handling code. Note that
memory_region_init_ram_nomigrate() is also updated to use &error_abort to indicate
a non-recoverable error, matching the behaviour recommended after similar
discussions on memory API failures for the recent nubus changes.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20211007221253.29024-3-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Make sure any errors that occur within the macfb realize chain are detected
and handled correctly to prevent crashes and to ensure that error messages are
reported back to the user.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20211007221253.29024-2-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Mark the shakti_c machine as not user creatable.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/639
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <c617a04d4e3dd041a3427b47a1b1d5ab475a2edd.1632871759.git.alistair.francis@wdc.com>
At present the codes detect whether the DMA channel is claimed by:
claimed = !!s->chan[ch].control & CONTROL_CLAIM;
As ! has higher precedence over & (bitwise and), this is essentially
claimed = (!!s->chan[ch].control) & CONTROL_CLAIM;
which is wrong, as any non-zero bit set in the control register will
produce a result of a claimed channel.
Fixes: de7c7988d2 ("hw/dma: sifive_pdma: reset Next* registers when Control.claim is set")
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210927072124.1564129-1-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
- Embed SerialMM in MchpPfSoCMMUartState and QOM-initialize it
- Alias SERIAL_MM 'chardev' property on MCHP_PFSOC_UART
- Forward SerialMM sysbus IRQ in mchp_pfsoc_mmuart_realize()
- Add DeviceReset() method
- Add vmstate structure for migration
- Register device in 'input' category
- Keep mchp_pfsoc_mmuart_create() behavior
Note, serial_mm_init() calls qdev_set_legacy_instance_id().
This call is only needed for backwards-compatibility of incoming
migration data with old versions of QEMU which implemented migration
of devices with hand-rolled code. Since this device didn't previously
handle migration at all, then it doesn't need to set the legacy
instance ID.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210925133407.1259392-4-f4bug@amsat.org
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Our device have 2 different I/O regions:
- a 16550 UART mapped for 32-bit accesses
- 13 extra registers
Instead of mapping each region on the main bus, introduce
a container, map the 2 devices regions on the container,
and map the container on the main bus.
Before:
(qemu) info mtree
...
0000000020100000-000000002010001f (prio 0, i/o): serial
0000000020100020-000000002010101f (prio 0, i/o): mchp.pfsoc.mmuart
0000000020102000-000000002010201f (prio 0, i/o): serial
0000000020102020-000000002010301f (prio 0, i/o): mchp.pfsoc.mmuart
0000000020104000-000000002010401f (prio 0, i/o): serial
0000000020104020-000000002010501f (prio 0, i/o): mchp.pfsoc.mmuart
0000000020106000-000000002010601f (prio 0, i/o): serial
0000000020106020-000000002010701f (prio 0, i/o): mchp.pfsoc.mmuart
After:
(qemu) info mtree
...
0000000020100000-0000000020100fff (prio 0, i/o): mchp.pfsoc.mmuart
0000000020100000-000000002010001f (prio 0, i/o): serial
0000000020100020-0000000020100fff (prio 0, i/o): mchp.pfsoc.mmuart.regs
0000000020102000-0000000020102fff (prio 0, i/o): mchp.pfsoc.mmuart
0000000020102000-000000002010201f (prio 0, i/o): serial
0000000020102020-0000000020102fff (prio 0, i/o): mchp.pfsoc.mmuart.regs
0000000020104000-0000000020104fff (prio 0, i/o): mchp.pfsoc.mmuart
0000000020104000-000000002010401f (prio 0, i/o): serial
0000000020104020-0000000020104fff (prio 0, i/o): mchp.pfsoc.mmuart.regs
0000000020106000-0000000020106fff (prio 0, i/o): mchp.pfsoc.mmuart
0000000020106000-000000002010601f (prio 0, i/o): serial
0000000020106020-0000000020106fff (prio 0, i/o): mchp.pfsoc.mmuart.regs
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Message-id: 20210925133407.1259392-3-f4bug@amsat.org
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The current MCHP_PFSOC_MMUART_REG_SIZE definition represent the
size occupied by all the registers. However all registers are
32-bit wide, and the MemoryRegionOps handlers are restricted to
32-bit:
static const MemoryRegionOps mchp_pfsoc_mmuart_ops = {
.read = mchp_pfsoc_mmuart_read,
.write = mchp_pfsoc_mmuart_write,
.impl = {
.min_access_size = 4,
.max_access_size = 4,
},
Avoid being triskaidekaphobic, simplify by using the number of
registers.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210925133407.1259392-2-f4bug@amsat.org
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The category of sifive_uart device is not set. Put it into the
'input' category.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210926105003.2716-3-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The category of shakti_uart device is not set. Put it into the
'input' category.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210926105003.2716-2-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The category of ibex_uart device is not set. Put it into the
'input' category.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210926105003.2716-1-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Linux limits the size of iovecs to 1024 (UIO_MAXIOV in the kernel
sources, IOV_MAX in POSIX). Because of this, on some host adapters
requests with many iovecs are rejected with -EINVAL by the
io_submit() or readv()/writev() system calls.
In fact, the same limit applies to SG_IO as well. To fix both the
EINVAL and the possible performance issues from using fewer iovecs
than allowed by Linux (some HBAs have max_segments as low as 128),
introduce a separate entry in BlockLimits to hold the max_segments
value from sysfs. This new limit is used only for SG_IO and clamped
to bs->bl.max_iov anyway, just like max_hw_transfer is clamped to
bs->bl.max_transfer.
Reported-by: Halil Pasic <pasic@linux.ibm.com>
Cc: Hanna Reitz <hreitz@redhat.com>
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: qemu-block@nongnu.org
Cc: qemu-stable@nongnu.org
Fixes: 18473467d5 ("file-posix: try BLKSECTGET on block devices too, do not round to power of 2", 2021-06-25)
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210923130436.1187591-1-pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
A huge acpi refactoring.
Fixes, cleanups all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmFcxB8PHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpldIH/jpPtsQr8oC1RrP8lTmiWh9vC9c3Xa5xfH7k
lXOn01kPprAWsm+qpoydOKJk/6v8TJ2E5nQ5AIU5EQvOEqSp8VnO0swHvTC7bwBa
1mGBvN3Ssjd/XFcgEc1xRJMzTO+Z1uF9tlq9ymDhLDtnuswyu5fl71NoXNVqE4st
r9wQrDX1lgzAUzL2QBr/g8wzx7aDS9HIyTrbl+ehzVEBrNKggo+AQgtSpyS1lxEC
NCIirfoaGgTKKrMASms5dXW44XNL/lXsZtheYrfF5nLiatCcthJNGnZ/BhUelH2B
EjXax7zs3IpWvRoGxRyqxElWgaCA2IXVvtLsT3WBqrTmi0Hoku8=
=nFLU
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pc,pci,virtio: features, fixes
A huge acpi refactoring.
Fixes, cleanups all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Tue 05 Oct 2021 02:31:11 PM PDT
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
* remotes/mst/tags/for_upstream: (47 commits)
hw/i386/amd_iommu: Add description/category to TYPE_AMD_IOMMU_PCI
hw/i386/amd_iommu: Rename SysBus specific functions as amdvi_sysbus_X()
hw/i386/amd_iommu: Rename amdviPCI TypeInfo
nvdimm: release the correct device list
virtio-balloon: Fix page-poison subsection name
bios-tables-test: Update ACPI DSDT table golden blobs for q35
hw/i386/acpi: fix conflicting IO address range for acpi pci hotplug in q35
bios-tables-test: allow changes in DSDT ACPI tables for q35
acpi: AcpiGenericAddress no longer used to map/access fields of MMIO, drop packed attribute
acpi: remove no longer used build_header()
acpi: build_facs: use build_append_int_noprefix() API to compose table
acpi: arm/virt: build_gtdt: use acpi_table_begin()/acpi_table_end() instead of build_header()
acpi: arm/virt: build_spcr: use acpi_table_begin()/acpi_table_end() instead of build_header()
acpi: arm/virt: build_spcr: fix invalid cast
acpi: arm/virt: convert build_iort() to endian agnostic build_append_FOO() API
acpi: arm: virt: build_iort: use acpi_table_begin()/acpi_table_end() instead of build_header()
acpi: arm: virt: build_dsdt: use acpi_table_begin()/acpi_table_end() instead of build_header()
acpi: build_dsdt_microvm: use acpi_table_begin()/acpi_table_end() instead of build_header()
acpi: arm/virt: madt: use build_append_int_noprefix() API to compose MADT table
acpi: x86: madt: use build_append_int_noprefix() API to compose MADT table
...
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
TYPE_AMD_IOMMU_PCI is user-creatable but not well described.
Implement its class_init() handler to add it to the 'Misc
devices' category, and add a description.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210926175648.1649075-4-f4bug@amsat.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Various functions are SysBus specific. Rename them using the
consistent amdvi_sysbus_XXX() pattern, to differentiate them
from PCI specific functions (which we'll add in the next
commit).
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210926175648.1649075-3-f4bug@amsat.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Per 'QEMU Coding Style':
Naming
======
Variables are lower_case_with_underscores; easy to type and read.
Rename amdviPCI variable as amdvi_pci.
amdviPCI_register_types() register more than PCI types:
TYPE_AMD_IOMMU_DEVICE inherits TYPE_X86_IOMMU_DEVICE which
itself inherits TYPE_SYS_BUS_DEVICE.
Rename it more generically as amdvi_register_types().
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210926175648.1649075-2-f4bug@amsat.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Message-Id: <20210624110415.187164-1-lizhijian@cn.fujitsu.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
The subsection name for page-poison was typo'd as:
vitio-balloon-device/page-poison
Note the missing 'r' in virtio.
When we have a machine type that enables page poison, and the guest
enables it (which needs a new kernel), things fail rather unpredictably.
The fallout from this is that most of the other subsections fail to
load, including things like the feature bits in the device, one
possible fallout is that the physical addresses of the queues
then get aligned differently and we fail with an error about
last_avail_idx being wrong.
It's not obvious to me why this doesn't produce a more obvious failure,
but virtio's vmstate loading is a bit open-coded.
Fixes: 7483cbbaf8 ("virtio-balloon: Implement support for page poison reporting feature")
bz: https://bugzilla.redhat.com/show_bug.cgi?id=1984401
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20210914131716.102851-1-dgilbert@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-Id: <20210924122802.1455362-35-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Drop usage of packed structures and explicit endian
conversions when building table and use endian agnostic
build_append_int_noprefix() API to build it.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-Id: <20210924122802.1455362-34-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
it replaces error-prone pointer arithmetic for build_header() API,
with 2 calls to start and finish table creation,
which hides offsets magic from API user.
while at it, replace packed structure with endian agnostic
build_append_FOO() API.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-Id: <20210924122802.1455362-33-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
it replaces error-prone pointer arithmetic for build_header() API,
with 2 calls to start and finish table creation,
which hides offsets magic from API user.
while at it, replace packed structure with endian agnostic
build_append_FOO() API.
PS:
Spec is Microsoft hosted, however 1.02 is no where to be found
(MS lists only the current revision) and the current revision is 1.07,
so bring comments in line with 1.07 as this is the only available spec.
There is no content change between originally implemented 1.02
(using QEMU code as reference) and 1.07. The only change is renaming
'Reserved2' field to 'Language', with the same 0 value.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-Id: <20210924122802.1455362-32-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
