The running_irq and last_active arrays represent state which
doesn't exist in a real hardware GIC. The only thing we use
them for is updating the running priority when an interrupt
is completed, but in fact we can use the active-priority
registers to do this. The running priority is always the
priority corresponding to the lowest set bit in the active
priority registers, because only one interrupt at any
particular priority can be active at once.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1438089748-5528-5-git-send-email-peter.maydell@linaro.org
A GICv2 has both GICC_APR<n> and GICC_NSAPR<n> registers, with
the latter holding the active priority bits for Group 1 interrupts
(usually Nonsecure interrupts), and the Nonsecure view of the
GICC_APR<n> is the second half of the GICC_NSAPR<n> registers.
Turn our half-hearted implementation of APR<n> into a proper
implementation of both APR<n> and NSAPR<n>:
* Add the underlying state for NSAPR<n>
* Make sure APR<n> aren't visible for pre-GICv2
* Implement reading of NSAPR<n>
* Make non-secure reads of APR<n> behave correctly
* Implement writing to APR<n> and NSAPR<n>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1438089748-5528-4-git-send-email-peter.maydell@linaro.org
Extracted duplicated initialization code from SW-emulated and KVM GIC
implementations and put into gic_init_irqs_and_mmio()
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Message-id: 8ea5b2781ef39cb5989420987fc73c70e377687d.1438758065.git.p.fedin@samsung.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The arm_gic_common reset function was missing reset code for
several of the GIC's state fields:
* bpr[]
* abpr[]
* priority1[]
* priority2[]
* sgi_pending[]
* irq_target[] (SMP configurations only)
These probably went unnoticed because most guests will either
never touch them, or will write to them in the process of
configuring the GIC before enabling interrupts.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1435602345-32210-1-git-send-email-peter.maydell@linaro.org
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
ICCICR/GICC_CTLR is banked in GICv1 implementations with Security
Extensions or in GICv2 in independent from Security Extensions.
This makes it possible to enable forwarding of interrupts from
the CPU interfaces to the connected processors for Group0 and Group1.
We also allow to set additional bits like AckCtl and FIQEn by changing
the type from bool to uint32. Since the field does not only store the
enable bit anymore and since we are touching the vmstate, we use the
opportunity to rename the field to cpu_ctlr.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1430502643-25909-9-git-send-email-peter.maydell@linaro.org
Message-id: 1429113742-8371-9-git-send-email-greg.bellows@linaro.org
[PMM: rewrote to store state in a single uint32_t rather than
keeping the NS and S banked variants separate; this considerably
simplifies the get/set functions]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
ICDDCR/GICD_CTLR is banked if the GIC has the security extensions,
and the S (or only) copy has separate enable bits for Group0 and
Group1 enable if the GIC implements interrupt groups.
EnableGroup0 (Bit [1]) in GICv1 is architecturally IMPDEF. Since this
bit (Enable Non-secure) is present in the integrated GIC of the Cortex-A9
MPCore, we support this bit in our GICv1 implementation too.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1430502643-25909-7-git-send-email-peter.maydell@linaro.org
Message-id: 1429113742-8371-8-git-send-email-greg.bellows@linaro.org
[PMM: rewritten to store the state in a single s->ctlr uint32,
with the NS register handled as an alias of bit 1 in that value;
added vmstate version bump]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Interrupt Group Registers allow the guest to configure interrupts
into one of two groups, where Group0 are higher priority and may
be routed to IRQ or FIQ, and Group1 are lower priority and always
routed to IRQ. (In a GIC with the security extensions Group0 is
Secure interrupts and Group 1 is NonSecure.)
The GICv2 always supports interrupt grouping; the GICv1 does only
if it implements the security extensions.
This patch implements the ability to read and write the registers;
the actual functionality the bits control will be added in a
subsequent patch.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1430502643-25909-5-git-send-email-peter.maydell@linaro.org
Message-id: 1429113742-8371-7-git-send-email-greg.bellows@linaro.org
[PMM: bring GIC_*_GROUP macros into line with the others, ie a
simple SET/CLEAR/TEST rather than GROUP0/GROUP1;
utility gic_has_groups() function;
minor style fixes;
bump vmstate version]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a QOM property which allows the GIC Security Extensions to be
enabled. These are an optional part of the GICv1 and GICv2 architecture.
This commit just adds the property and some sanity checks that it
is only enabled on GIC revisions that support it.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1430502643-25909-3-git-send-email-peter.maydell@linaro.org
Message-id: 1429113742-8371-5-git-send-email-greg.bellows@linaro.org
[PMM: changed property name, added checks that it isn't set for
older GIC revisions or if using the KVM VGIC; reworded commit message]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use constant rather than a plain number.
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Adam Lackorzynski <adam@os.inf.tu-dresden.de>
Message-id: 1408372255-12358-5-git-send-email-adam@os.inf.tu-dresden.de
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The GICC_APRn registers are not currently supported by the ARM GIC v2.0
emulation. This patch adds the missing state.
Note that we also change the number of APRs to use a define GIC_NR_APRS
based on the maximum number of preemption levels. This patch also adds
RAZ/WI accessors for the four registers on the emulated CPU interface.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a binary_point field to the gic emulation structure and support
setting/getting this register now when we have it. We don't actually
support interrupt grouping yet, oh well.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Right now the arm gic emulation doesn't keep track of the source of an
SGI (which apparently Linux guests don't use, or they're fine with
assuming CPU 0 always).
Add the necessary matrix on the GICState structure and maintain the data
when setting and clearing the pending state of an IRQ and make the state
visible to the guest.
Note that we always choose to present the source as the lowest-numbered
CPU in case multiple cores have signalled the same SGI number to a core
on the system.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* QOM interface fixes and unit test
* Device no_user sanitization and documentation
* Device error reporting improvement
* Conversion of APIC, ICC, IOAPIC to QOM realization model
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=WrhM
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'afaerber/tags/qom-devices-for-anthony' into staging
QOM infrastructure fixes and device conversions
* QOM interface fixes and unit test
* Device no_user sanitization and documentation
* Device error reporting improvement
* Conversion of APIC, ICC, IOAPIC to QOM realization model
# gpg: Signature made Tue 24 Dec 2013 09:04:05 AM PST using RSA key ID 3E7E013F
# gpg: Good signature from "Andreas Färber <afaerber@suse.de>"
# gpg: aka "Andreas Färber <afaerber@suse.com>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 174F 0347 1BCC 221A 6175 6F96 FA2E D12D 3E7E 013F
* afaerber/tags/qom-devices-for-anthony: (24 commits)
qdev-monitor: Improve error message for -device nonexistant
ioapic: QOM'ify ioapic
ioapic: Cleanup for QOM'ification
icc_bus: QOM'ify ICC
apic: QOM'ify APIC
apic: Cleanup for QOM'ification
qdev: Drop misleading qbus_free() function
qom: Detect bad reentrance during object_class_foreach()
tests: Test QOM interface casting
qom: Do not register interface "types" in the type table and fix names
qom: Split out object and class caches
qdev: Document that pointer properties kill device_add
hw: cannot_instantiate_with_device_add_yet due to pointer props
qdev-monitor: Avoid device_add crashing on non-device driver name
qdev: Do not let the user try to device_add when it cannot work
isa: Clean up use of cannot_instantiate_with_device_add_yet
vt82c686: Clean up use of cannot_instantiate_with_device_add_yet
piix3 piix4: Clean up use of cannot_instantiate_with_device_add_yet
ich9: Document why cannot_instantiate_with_device_add_yet
pci-host: Consistently set cannot_instantiate_with_device_add_yet
...
TRIGGER can really mean mean anything (e.g. was it triggered, is it
level-triggered, is it edge-triggered, etc.). Rename to EDGE_TRIGGER to
make the code comprehensible without looking up the data structure.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Message-id: 1387606179-22709-2-git-send-email-christoffer.dall@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
device_add plugs devices into suitable bus. For "real" buses, that
actually connects the device. For sysbus, the connections need to be
made separately, and device_add can't do that. The device would be
left unconnected, and could not possibly work.
Quite a few, but not all sysbus devices already set
cannot_instantiate_with_device_add_yet in their class init function.
Set it in their abstract base's class init function
sysbus_device_class_init(), and remove the now redundant assignments
from device class init functions.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel.a@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
In an ideal world, machines can be built by wiring devices together
with configuration, not code. Unfortunately, that's not the world we
live in right now. We still have quite a few devices that need to be
wired up by code. If you try to device_add such a device, it'll fail
in sometimes mysterious ways. If you're lucky, you get an
unmysterious immediate crash.
To protect users from such badness, DeviceClass member no_user used to
make device models unavailable with -device / device_add, but that
regressed in commit 18b6dad. The device model is still omitted from
help, but is available anyway.
Attempts to fix the regression have been rejected with the argument
that the purpose of no_user isn't clear, and it's prone to misuse.
This commit clarifies no_user's purpose. Anthony suggested to rename
it cannot_instantiate_with_device_add_yet_due_to_internal_bugs, which
I shorten somewhat to keep checkpatch happy. While there, make it
bool.
Every use of cannot_instantiate_with_device_add_yet gets a FIXME
comment asking for rationale. The next few commits will clean them
all up, either by providing a rationale, or by getting rid of the use.
With that done, the regression fix is hopefully acceptable.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel.a@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Rename NCPU to GIC_NCPU and move GICState away from gic_internal.h.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
