The nRF51 contains three regions of non-volatile memory (NVM):
- CODE (R/W): contains code
- FICR (R): Factory information like code size, chip id etc.
- UICR (R/W): Changeable configuration data. Lock bits, Code
protection configuration, Bootloader address, Nordic SoftRadio
configuration, Firmware configuration.
Read and write access to the memories is managed by the
Non-volatile memory controller.
Memory schema:
[ CPU ] -+- [ NVM, either FICR, UICR or CODE ]
| |
\- [ NVMC ]
Signed-off-by: Steffen Görtz <contrib@steffen-goertz.de>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Tested-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20190201023357.22596-2-stefanha@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
A flawed test lead to the instructions always being treated as
unallocated encodings.
Fixes: https://bugs.launchpad.net/bugs/1813460
Signed-off-by: Remi Denis-Courmont <remi.denis.courmont@huawei.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Since QEMU does not support the ARMv8.2-LVA, Large Virtual Address,
extension (yet), the VA address space is 48-bits plus a sign bit. User
mode can only handle the positive half of the address space, so that
makes a limit of 48 bits.
(With LVA, it would be 53 and 52 bits respectively.)
The incorrectly large address space conflicts with PAuth instructions,
which use bits 48-54 and 56-63 for the pointer authentication code. This
also conflicts with (as yet unsupported by QEMU) data tagging and with
the ARMv8.5-MTE extension.
Signed-off-by: Remi Denis-Courmont <remi.denis.courmont@huawei.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Initialize the keys to a non-zero value on process start.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Drop the pac properties. This approach cannot work as written
because the properties are applied before arm_cpu_reset, which
zeros SCTLR_EL1 (amongst everything else).
We can re-introduce the properties if they turn out to be useful.
But since linux 5.0 enables all of the keys, they may not be.
Fixes: 1ae9cfbd47
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Until now, the set_pc logic was unclear, which raised questions about
whether it should be used directly, applying a value to PC or adding
additional checks, for example, set the Thumb bit in Arm cpu. Let's set
the set_pc logic for “Configure the PC, as was done in the ELF file”
and implement synchronize_with_tb hook for preserving PC to cpu_tb_exec.
Signed-off-by: Julia Suvorova <jusual@mail.ru>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190129121817.7109-1-jusual@mail.ru
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
These bits become writable with the ARMv8.3-PAuth extension.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190129143511.12311-1-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Make PMU overflow interrupts more accurate by using a timer to predict
when they will overflow rather than waiting for an event to occur which
allows us to otherwise check them.
Signed-off-by: Aaron Lindsay <aaron@os.amperecomputing.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190124162401.5111-3-aaron@os.amperecomputing.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Whenever we notice that a counter overflow has occurred, send an
interrupt. This is made more reliable with the addition of a timer in a
follow-on commit.
Signed-off-by: Aaron Lindsay <aaron@os.amperecomputing.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190124162401.5111-2-aaron@os.amperecomputing.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In disas_simd_indexed(), for the case of "complex fp", each indexable
element is a complex pair, so the total size is twice that indicated
in the 'size' field in the encoding. We were trying to do this
"double the size" operation with a left shift by 1, but this is
incorrect because the 'size' field is a MO_8/MO_16/MO_32/MO_64
value, and doubling the size should be done by a simple increment.
This meant we were mishandling FCMLA (by element) of values where
the real and imaginary parts are 32-bit floats, and would incorrectly
UNDEF this encoding. (No other insns take this code path, and for
16-bit floats it happens that 1 << 1 and 1 + 1 are both the same).
Reported-by: Laurent Desnogues <laurent.desnogues@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Laurent Desnogues <laurent.desnogues@gmail.com>
Message-id: 20190129140411.682-3-peter.maydell@linaro.org
The FCMLA (by element) instruction exists in the
"vector x indexed element" encoding group, but not in
the "scalar x indexed element" group. Correctly UNDEF
the unallocated encodings.
Reported-by: Laurent Desnogues <laurent.desnogues@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Laurent Desnogues <laurent.desnogues@gmail.com>
Message-id: 20190129140411.682-2-peter.maydell@linaro.org
The tcg_register_iommu_notifier() code has a GArray of
TCGIOMMUNotifier structs which it has registered by passing
memory_region_register_iommu_notifier() a pointer to the embedded
IOMMUNotifier field. Unfortunately, if we need to enlarge the
array via g_array_set_size() this can cause a realloc(), which
invalidates the pointer that memory_region_register_iommu_notifier()
put into the MemoryRegion's iommu_notify list. This can result
in segfaults.
Switch the GArray to holding pointers to the TCGIOMMUNotifier
structs, so that we can individually allocate and free them.
Cc: qemu-stable@nongnu.org
Fixes: 1f871c5e6b ("exec.c: Handle IOMMUs in address_space_translate_for_iotlb()")
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190128174241.5860-1-peter.maydell@linaro.org
In the AdvSIMD scalar x indexed element and vector x indexed element
encoding group, the SDOT and UDOT instructions are vector only,
and their opcode is unallocated in the scalar group. Correctly
UNDEF this unallocated encoding.
Reported-by: Laurent Desnogues <laurent.desnogues@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Laurent Desnogues <laurent.desnogues@gmail.com>
Message-id: 20190125182626.9221-8-peter.maydell@linaro.org
In the encoding groups
* floating-point data-processing (1 source)
* floating-point data-processing (2 source)
* floating-point data-processing (3 source)
* floating-point immediate
* floating-point compare
* floating-ponit conditional compare
* floating-point conditional select
bit 31 is M and bit 29 is S (and bit 30 is 0, already checked at
this point in the decode). None of these groups allocate any
encoding for M=1 or S=1. We checked this in disas_fp_compare(),
disas_fp_ccomp() and disas_fp_csel(), but missed it in disas_fp_1src(),
disas_fp_2src(), disas_fp_3src() and disas_fp_imm().
We also missed that in the fp immediate encoding the imm5 field
must be all zeroes.
Correctly UNDEF the unallocated encodings here.
Reported-by: Laurent Desnogues <laurent.desnogues@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Laurent Desnogues <laurent.desnogues@gmail.com>
Message-id: 20190125182626.9221-7-peter.maydell@linaro.org
In the "add/subtract (extended register)" encoding group, the "opt"
field in bits [23:22] must be zero. Correctly UNDEF the unallocated
encodings where this field is not zero.
Reported-by: Laurent Desnogues <laurent.desnogues@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Laurent Desnogues <laurent.desnogues@gmail.com>
Message-id: 20190125182626.9221-6-peter.maydell@linaro.org
In the AdvSIMD load/store single structure encodings, the
non-post-indexed case should have zeroes in [20:16] (which is the
Rm field for the post-indexed case). Bit 31 must also be zero
(a check we got right in ldst_multiple but not here). Correctly
UNDEF these unallocated encodings.
Reported-by: Laurent Desnogues <laurent.desnogues@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Laurent Desnogues <laurent.desnogues@gmail.com>
Message-id: 20190125182626.9221-5-peter.maydell@linaro.org
In the AdvSIMD load/store multiple structures encodings,
the non-post-indexed case should have zeroes in [20:16]
(which is the Rm field for the post-indexed case).
Correctly UNDEF the currently unallocated encodings which
have non-zeroes in those bits.
Reported-by: Laurent Desnogues <laurent.desnogues@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Laurent Desnogues <laurent.desnogues@gmail.com>
Message-id: 20190125182626.9221-4-peter.maydell@linaro.org
The PRFM prefetch insn in the load/store with imm9 encodings
requires idx field 0b00; we were underdecoding this by
only checking !is_unpriv (which is equivalent to idx != 2).
Correctly UNDEF the unallocated encodings where idx == 0b01
and 0b11 as well as 0b10.
Reported-by: Laurent Desnogues <laurent.desnogues@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Laurent Desnogues <laurent.desnogues@gmail.com>
Message-id: 20190125182626.9221-3-peter.maydell@linaro.org
The "system instructions" and "system register move" subcategories
of "branches, exception generating and system instructions" for A64
only apply if bits [23:22] are zero; other values are currently
unallocated. Correctly UNDEF these unallocated encodings.
Reported-by: Laurent Desnogues <laurent.desnogues@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Laurent Desnogues <laurent.desnogues@gmail.com>
Message-id: 20190125182626.9221-2-peter.maydell@linaro.org
Add a model of the MPS2 FPGA image described in Application Note
AN521. This is identical to the AN505 image, except that it uses
the SSE-200 rather than the IoTKit and so has two Cortex-M33 CPUs.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-24-peter.maydell@linaro.org
In preparation for adding support for the AN521 MPS2 image, we need
to handle wiring up the MPS2 device interrupt lines to both CPUs in
the SSE-200, rather than just the one that the IoTKit has.
Abstract out a "connect to the IoTKit interrupt line" function
and make it connect to a splitter which feeds both sets of inputs
for the SSE-200 case.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-23-peter.maydell@linaro.org
Add a model of the SSE-200, now we have put in all
the code that lets us make it different from the IoTKit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-22-peter.maydell@linaro.org
Instantiate a copy of the CPU_IDENTITY register block for each CPU
in an SSE-200.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-21-peter.maydell@linaro.org
The SSE-200 has a CPU_IDENTITY register block, which is a set of
read-only registers. As well as the usual PID/CID registers, there
is a single CPUID register which indicates whether the CPU is CPU 0
or CPU 1. Implement a model of this register block.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-20-peter.maydell@linaro.org
The SSE-200 has a "CPU local security control" register bank; add an
unimplemented-device stub for it. (The register bank has only one
interesting register, which allows the guest to lock down changes
to various CPU registers so they cannot be modified further. We
don't support that in our Cortex-M33 model anyway.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-19-peter.maydell@linaro.org
The SSE-200 gives each CPU a register bank to use to control its
L1 instruction cache. Put in an unimplemented-device stub for this.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-18-peter.maydell@linaro.org
Add unimplemented-device stubs for the various Power Policy Unit
devices that the SSE-200 has.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-17-peter.maydell@linaro.org
The SSE-200 has two Message Handling Units (MHUs), which sit behind
the APB PPC0. Wire up some unimplemented-device stubs for these,
since we don't yet implement a real model of this device.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-16-peter.maydell@linaro.org
The SYS_VERSION and SYS_CONFIG register values differ between the
IoTKit and SSE-200. Make them configurable via QOM properties rather
than hard-coded, and set them appropriately in the ARMSSE code that
instantiates the IOTKIT_SYSINFO device.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-15-peter.maydell@linaro.org
Create a cluster object to hold each CPU in the SSE. They are
logically distinct and may be configured differently (for instance
one may not have an FPU where the other does).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-14-peter.maydell@linaro.org
Give each CPU its own container memory region. This is necessary
for two reasons:
* some devices are instantiated one per CPU and the CPU sees only
its own device
* since a memory region can only be put into one container, we must
give each armv7m object a different MemoryRegion as its 'memory'
property, or a dual-CPU configuration will assert on realize when
the second armv7m object tries to put the MR into a container when
it is already in the first armv7m object's container
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-13-peter.maydell@linaro.org
The SSE-200 has two Cortex-M33 CPUs. These see the same view
of memory, with the exception of the "private CPU region" which
has per-CPU devices. Internal device interrupts for SSE-200
devices are mostly wired up to both CPUs, with the exception of
a few per-CPU devices. External GPIO inputs on the SSE-200
device are provided for the second CPU's interrupts above 32,
as is already the case for the first CPU.
Refactor the code to support creation of multiple CPUs.
For the moment we leave all CPUs with the same view of
memory: this will not work in the multiple-CPU case, but
we will fix this in the following commit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-12-peter.maydell@linaro.org
For the IoTKit the SRAM bank size is always 32K (15 bits); for the
SSE-200 this is a configurable parameter, which defaults to 32K but
can be changed when it is built into a particular SoC. For instance
the Musca-B1 board sets it to 128K (17 bits).
Make the bank size a QOM property. We follow the SSE-200 hardware in
naming the parameter SRAM_ADDR_WIDTH, which specifies the number of
address bits of a single SRAM bank.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-11-peter.maydell@linaro.org
The SSE-200 has four banks of SRAM, each with its own
Memory Protection Controller, where the IoTKit has only one.
Make the number of SRAM banks a field in ARMSSEInfo.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-10-peter.maydell@linaro.org
The SSE-200 has 4 banks of SRAM, each with its own internal
Memory Protection Controller. The interrupt status for these
extra MPCs appears in the same security controller SECMPCINTSTATUS
register as the MPC for the IoTKit's single SRAM bank. Enhance the
iotkit-secctl device to allow 4 MPCs. (If the particular IoTKit/SSE
variant in use does not have all 4 MPCs then the unused inputs will
simply result in the SECMPCINTSTATUS bits being zero as required.)
The hardcoded constant "1"s in armsse.c indicate the actual number
of SRAM MPCs the IoTKit has, and will be replaced in the following
commit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-9-peter.maydell@linaro.org
Rename the files that used to be iotkit.[ch] to
armsse.[ch] to reflect the fact they new cover
multiple Arm subsystems for embedded.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-8-peter.maydell@linaro.org
Rename various internal uses of 'iotkit' in hw/arm/iotkit.c to
'armsse', for consistency. The remaining occurences are:
* related to the devices TYPE_IOTKIT_SYSCTL, TYPE_IOTKIT_SYSINFO,
etc, which this refactor is not touching
* references that apply specifically to the IoTKit (like
the lack of a private CPU region)
* the vmstate, which keeps its old "iotkit" name for
migration compatibility reasons
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-7-peter.maydell@linaro.org
The Arm SSE-200 Subsystem for Embedded is a revised and
extended version of the older IoTKit SoC. Prepare for
adding a model of it by refactoring the IoTKit code into
an abstract base class which contains the functionality,
driven by a class data block specific to each subclass.
(This is the same approach used by the existing bcm283x
SoC family implementation.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-6-peter.maydell@linaro.org
The Arm IoTKit was effectively the forerunner of a series of
subsystems for embedded SoCs, named the SSE-050, SSE-100 and SSE-200:
https://developer.arm.com/products/system-design/subsystems
These are generally quite similar, though later iterations have
extra devices that earlier ones do not.
We want to add a model of the SSE-200, which means refactoring the
IoTKit code into an abstract base class and subclasses (using the
same design that the bcm283x SoC and Aspeed SoC family
implementations do). As a first step, rename the IoTKit struct and
QOM macros to ARMSSE, which is what we're going to name the base
class. We temporarily retain TYPE_IOTKIT to avoid changing the
code that instantiates a TYPE_IOTKIT device here and then changing
it back again when it is re-introduced as a subclass.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-5-peter.maydell@linaro.org
Expose "start-powered-off" as a property of the ARMv7M container,
which we just pass through to the CPU object in the same way that we
do for "init-svtor" and "idau". (We want this for the SSE-200, which
powers up only the first CPU at reset and leaves the second powered
down.)
As with the other CPU properties here, we can't just use alias
properties, because the CPU QOM object is not created until armv7m
realize time.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-4-peter.maydell@linaro.org
Rather than just creating the CPUs with object_new, make them child
objects of the armv7m container. This will allow the cluster code to
find the CPUs if an armv7m object is made a child of a cluster object.
object_new_with_props() will do the parenting for us.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-3-peter.maydell@linaro.org
Currently the ARMv7M NVIC object's realize method assumes that the
CPU the NVIC is attached to is CPU 0, because it thinks there can
only ever be one CPU in the system. To allow a dual-Cortex-M33
setup we need to remove this assumption; instead the armv7m
wrapper object tells the NVIC its CPU, in the same way that it
already tells the CPU what the NVIC is.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-2-peter.maydell@linaro.org
set object owner in memory_region_init_ram() instead
of NULL.
Signed-off-by: kumar sourav <sourav.jb1988@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190125155630.17430-1-sourav.jb1988@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The new device_id property specifies which value to use for the vendor
specific designator in the Device Identification VPD page.
In particular, this is necessary for libvirt to maintain guest ABI
compatibility when no serial number is given and a VM is switched from
-drive (where the BlockBackend name is used) to -blockdev (where the
vendor specific designator is left out by default).
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
scsi-disk includes in the Device Identification VPD page, depending on
configuration amongst others, a vendor specific designator that consists
either of the serial number if given or the BlockBackend name (which is
a host detail that better shouldn't have been leaked to the guest, but
now we have to maintain it for compatibility).
With anonymous BlockBackends, i.e. scsi-disk devices constructed with
drive=<node-name>, and no serial number explicitly specified, this ends
up as an empty string. If this happens to more than one disk, we have
accidentally signalled to the OS that this is a multipath setup, which
is obviously not what was intended.
Instead of using an empty string for the vendor specific designator,
simply leave out that designator, which makes Linux detect such setups
as separate disks again.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
The cmd() method of the QEMUQtestProtocol class sends a qtest command
to QEMU but doesn't wait for the return message ("OK", "FAIL", "ERR").
Because of this, it can return control to the caller before the
command has actually finished.
In cases like clock_step or clock_set this means that cmd() can return
before all the timers triggered by the clock change have been fired.
This can be fixed by making cmd() wait for the output of the qtest
command.
This fixes iotests 093 and 136, which are flaky since commit
8258292e18 when the machine is under heavy workload.
Signed-off-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
bdrv_co_invalidate_cache() clears the BDRV_O_INACTIVE flag before
actually activating a node so that the correct permissions etc. are
taken. In case of errors, the flag must be restored so that the next
call to bdrv_co_invalidate_cache() retries activation.
Restoring the flag was missing in the error path for a failed
parent->role->activate() call. The consequence is that this attempt to
activate all images correctly fails because we still set errp, however
on the next attempt BDRV_O_INACTIVE is already clear, so we return
success without actually retrying the failed action.
An example where this is observable in practice is migration to a QEMU
instance that has a raw format block node attached to a guest device
with share-rw=off (the default) while another process holds
BLK_PERM_WRITE for the same image. In this case, all activation steps
before parent->role->activate() succeed because raw can tolerate other
writers to the image. Only the parent callback (in particular
blk_root_activate()) tries to implement the share-rw=on property and
requests exclusive write permissions. This fails when the migration
completes and correctly displays an error. However, a manual 'cont' will
incorrectly resume the VM without calling blk_root_activate() again.
This case is described in more detail in the following bug report:
https://bugzilla.redhat.com/show_bug.cgi?id=1531888
Fix this by correctly restoring the BDRV_O_INACTIVE flag in the error
path.
Cc: qemu-stable@nongnu.org
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Tested-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Steffen Görtz
Remi Denis-Courmont
Richard Henderson
Julia Suvorova
Aaron Lindsay OS
Peter Maydell
kumar sourav
Kevin Wolf
Alberto Garcia