The MacOS toolbox ROM performs 4 byte reads/writes when transferring data to
and from the target. Since the SCSI bus is 16-bits wide, use the memory API
to split a 4 byte access into 2 x 2 byte accesses.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-31-mark.cave-ayland@ilande.co.uk>
Now that all data is transferred via the FIFO (ti_buf) there is no need to track
the source buffer being used for the data transfer. This also eliminates the
need for a separate subsection for PDMA state migration.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-30-mark.cave-ayland@ilande.co.uk>
PDMA as implemented on the Quadra 800 uses DREQ to load data into the FIFO
up to a maximum of 16 bytes at a time. The MacOS toolbox ROM requires this
because it mixes FIFO and PDMA transfers whilst checking the FIFO status
and counter registers to ensure success.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-29-mark.cave-ayland@ilande.co.uk>
Currently the target selection for PDMA is done after the SCSI command has been
delivered which is not correct. Perform target selection as part of the initial
get_cmd() call when the command is submitted: if no target is present, don't
raise DRQ.
If the target is present then switch to the command phase since the MacOS toolbox
ROM checks for this before attempting to submit the SCSI command.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-28-mark.cave-ayland@ilande.co.uk>
This better describes the purpose of the function.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-27-mark.cave-ayland@ilande.co.uk>
The cmdbuf is really just a copy of FIFO data (including extra message phase
bytes) so its pdma_origin is effectively TI. Fortunately we already know when
we are receiving a SCSI command since do_cmd == 1 which enables us to
distinguish between the two cases in esp_pdma_read()/esp_pdma_write().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-26-mark.cave-ayland@ilande.co.uk>
Real hardware simply counts down using the in-built TC to determine when the
the PDMA request is complete. Use the TC to determine the PDMA transfer length
which then enables us to remove the redundant pdma_len variable.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-25-mark.cave-ayland@ilande.co.uk>
This eliminates the last user of the PDMA-specific pdma_cur variable which can
now be removed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-24-mark.cave-ayland@ilande.co.uk>
Here the updates to async_len and ti_size are moved into the corresponding
esp_pdma_read()/esp_pdma_write() function to eliminate the reference to
pdma_cur in do_dma_pdma_cb().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-23-mark.cave-ayland@ilande.co.uk>
Now that PDMA SCSI commands are accumulated in cmdbuf in the same way as normal
commands, the existing logic for locating the start of the SCSI command in
cmdbuf via cmdlen can be used. This enables the PDMA-specific pdma_start and
also get_pdma_buf() to be removed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-22-mark.cave-ayland@ilande.co.uk>
Now that all SCSI commands are accumulated in cmdbuf, remove the buf and buflen
parameters from get_cmd() since these always reference cmdbuf and ESP_CMDBUF_SZ
respectively.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-21-mark.cave-ayland@ilande.co.uk>
Now that all SCSI commands are accumulated in cmdbuf, remove the buf parameter
from do_cmd() since this always points to cmdbuf.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-20-mark.cave-ayland@ilande.co.uk>
ESP SCSI commands are already accumulated in cmdbuf and so there is no need to
keep a separate pdma_buf buffer. Accumulate SCSI commands for PDMA transfers in
cmdbuf instead of pdma_buf so update cmdlen accordingly and change pdma_origin
for PDMA transfers to CMD which allows the PDMA origin to be removed.
This commit also removes a stray memcpy() from get_cmd() which is a no-op because
cmdlen is always zero at the start of a command.
Notionally the removal of pdma_buf from vmstate_esp_pdma also breaks migration
compatibility for the PDMA subsection until its complete removal by the end of
the series.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-19-mark.cave-ayland@ilande.co.uk>
This is the first step in removing get_pdma_buf() from esp.c.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-17-mark.cave-ayland@ilande.co.uk>
The limiting of DMA transfers to the maximum size of the available data is already
handled by esp_do_dma() and do_dma_pdma_cb().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-15-mark.cave-ayland@ilande.co.uk>
The ESP device already keeps track of the remaining bytes left to transfer via
its TC (transfer counter) register which is decremented for each byte that
is transferred across the SCSI bus.
Switch the transfer logic to use the value of TC instead of dma_left and then
remove dma_left completely, adding logic to the vmstate_esp post_load() function
to transfer the old dma_left value to the TC register during migration from
older versions.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-14-mark.cave-ayland@ilande.co.uk>
The value of dma_counter is set once at the start of the transfer and remains
the same until the transfer is complete. This allows the check in esp_transfer_data
to be simplified since dma_left will always be non-zero until the transfer is
completed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-13-mark.cave-ayland@ilande.co.uk>
Perform the length adjustment whereby a value of 0 in the STC represents
a transfer length of 0x10000 at the point where the TC is loaded at the
start of a DMA command rather than just when a TI (Transfer Information)
command is executed. This better matches the description as given in the
datasheet.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-12-mark.cave-ayland@ilande.co.uk>
This function simplifies reading the STC register value without having to manually
shift each individual 8-bit value.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-11-mark.cave-ayland@ilande.co.uk>
These functions simplify reading and writing the TC register value without having to
manually shift each individual 8-bit value.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-10-mark.cave-ayland@ilande.co.uk>
The transfer direction is currently determined by checking the sign of ti_size
but as this series progresses ti_size can be zero at the end of the transfer.
Use the SCSI phase to determine the transfer direction as used in other SCSI
controller implementations.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-9-mark.cave-ayland@ilande.co.uk>
This will become more useful later when trying to debug mixed FIFO and PDMA
requests.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-8-mark.cave-ayland@ilande.co.uk>
Move the trace event to the end of the function so that it correctly reports
the returned value if it doesn't come directly from the rregs array.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-7-mark.cave-ayland@ilande.co.uk>
This enables us to determine whether the command being issued is for a DMA or a
non-DMA transfer.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-6-mark.cave-ayland@ilande.co.uk>
The QOM object representing ESPState is currently embedded within both the
SYSBUS_ESP and PCI_ESP devices with migration state handled by embedding
vmstate_esp within each device using VMSTATE_STRUCT.
Since the vmstate_esp fields are embedded directly within the migration
stream, the incoming vmstate_esp version_id is lost. The only version information
available is that from vmstate_sysbus_esp_scsi and vmstate_esp_pci_scsi, but
those versions represent their respective devices and not that of the underlying
ESPState.
Resolve this by adding a new version-dependent field in vmstate_sysbus_esp_scsi
and vmstate_esp_pci_scsi which stores the vmstate_esp version_id field within
ESPState to be used to allow migration from older QEMU versions.
Finally bump the vmstate_esp version to 5 to cover the upcoming ESPState changes
within this patch series.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-5-mark.cave-ayland@ilande.co.uk>
Make this new QOM device state a child device of both the sysbus-esp and esp-pci
implementations.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-4-mark.cave-ayland@ilande.co.uk>
The existing ESP QOM type currently represents a sysbus device with an embedded
ESP state. Rename the type to SYSBUS_ESP accordingly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-3-mark.cave-ayland@ilande.co.uk>
Some SCSI drivers like virtio have an internal mapping for the
host_status. This patch moves the host_status translation into
the SCSI drivers to allow those drivers to set up the correct
values.
Signed-off-by: Hannes Reinecke <hare@suse.de>.
[Added default handling to avoid touching all drivers. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently sg_io_sense_from_errno() converts the two input parameters
'errno' and 'io_hdr' into sense code and SCSI status. Having
split the function off into scsi_sense_from_errno() and
scsi_sense_from_host_status(), both of which are available generically,
we now inline the logic in the callers so that scsi-disk and
scsi-generic will be able to pass host_status to the HBA.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Message-Id: <20201116184041.60465-7-hare@suse.de>
[Put together from "scsi-disk: Add sg_io callback to evaluate status"
and what remains of "scsi: split sg_io_sense_from_errno() in two functions",
with many other fixes. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If a READ CAPACITY command would fail, for example s->qdev.blocksize would be
set to zero and cause a division by zero on the next use.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
PCI_DEVICE has overwritten DeviceState::unrealize (pci_qdev_unrealize).
However, LSI53C895A, which is a subclass of PCI_DEVICE, overwrites it
again and doesn't save the parent's implementation so the PCI_DEVICE's
implementation of DeviceState::unrealize will never be called when
unrealize a LSI53C895A device. And it will lead to memory leak and
unplug failure.
For a PCI device, it's better to implement PCIDevice::exit instead of
DeviceState::unrealize. So let's change to use PCIDevice::exit.
Fixes: a8632434c7 ("lsi: implement I/O memory space for Memory Move instructions")
Cc: qemu-stable@nongnu.org
Signed-off-by: Peng Liang <liangpeng10@huawei.com>
Message-Id: <20210302133016.1221081-1-liangpeng10@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The command complete callback has a SCSIRequest as the first argument,
and the status field of that structure is identical to the 'status'
argument. So drop the argument from the callback.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Message-Id: <20201116184041.60465-3-hare@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Right now, recoverable sense values are only passed directly to the
guest only for rerror=report. However, when rerror/werror are 'stop'
we still don't want the host to be involved on every UNIT ATTENTION
(especially considered that the QMP event will not have enough information
to act on the report).
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Instead of fishing it from *r->status, just pass the SCSI status
as a positive value of the second parameter and an errno as a
negative value.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The new function is an extension of the switch statement in scsi-disk.c
which also includes the errno cases only found in sg_io_sense_from_errno.
This allows us to consolidate the errno handling.
Extracted from a patch by Hannes Reinecke <hare@suse.de>.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When requested to ignore errors, just do nothing and let the
request complete normally. This means that the request will
be accounted correctly.
This is what commit 40dce4ee61 ("scsi-disk: fix rerror/werror=ignore",
2018-10-19) was supposed to do:
Fixes: 40dce4ee61 ("scsi-disk: fix rerror/werror=ignore", 2018-10-19)
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If virtio_scsi_dataplane_start fails, there is a small window when it drops the
aio lock (in aio_wait_bh_oneshot) and the dataplane's AIO handler can
still run during that window.
This is done after the dataplane was marked as fenced, thus we use this flag
to avoid it doing any IO.
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20201217150040.906961-2-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
'enospc' is the default for -drive, but qemu allows user to set
drive option werror. If werror of scsi-generic is set to 'report'
by user, qemu will not allow vm to start.
This patch allow user to set werror as 'report' for scsi-generic.
Signed-off-by: Zihao Chang <changzihao1@huawei.com>
Reviewed-by: Fam Zheng <fam@euphon.net>
Message-Id: <20201103061240.1364-1-changzihao1@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add tracepoints for SG_IO commands to allow for debugging
of SG_IO commands.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Message-Id: <20201116183114.55703-4-hare@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The current code sets an infinite timeout on SG_IO requests,
causing the guest to stall if the host experiences a frame
loss.
This patch adds an 'io_timeout' parameter for SCSIDevice to
make the SG_IO timeout configurable, and also shortens the
default timeout to 30 seconds to avoid infinite stalls.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Message-Id: <20201116183114.55703-3-hare@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Count number of queues that we initialized and only deinitialize these that we
initialized successfully.
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20201217150040.906961-3-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently, blk_is_read_only() tells whether a given BlockBackend can
only be used in read-only mode because its root node is read-only. Some
callers actually try to answer a slightly different question: Is the
BlockBackend configured to be writable, by taking write permissions on
the root node?
This can differ, for example, for CD-ROM devices which don't take write
permissions, but may be backed by a writable image file. scsi-cd allows
write requests to the drive if blk_is_read_only() returns false.
However, the write request will immediately run into an assertion
failure because the write permission is missing.
This patch introduces separate functions for both questions.
blk_supports_write_perm() answers the question whether the block
node/image file can support writable devices, whereas blk_is_writable()
tells whether the BlockBackend is currently configured to be writable.
All calls of blk_is_read_only() are converted to one of the two new
functions.
Fixes: https://bugs.launchpad.net/bugs/1906693
Cc: qemu-stable@nongnu.org
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20210118123448.307825-2-kwolf@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The documentation for bdrv_set_aio_context_ignore() states this:
* The caller must own the AioContext lock for the old AioContext of bs, but it
* must not own the AioContext lock for new_context (unless new_context is the
* same as the current context of bs).
As blk_set_aio_context() makes use of this function, this rule also
applies to it.
Fix all occurrences where this rule wasn't honored.
Suggested-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Sergio Lopez <slp@redhat.com>
Message-Id: <20201214170519.223781-2-slp@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
Add trace events for virtio command and response tracing.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Message-Id: <20201116183114.55703-2-hare@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 8118f0950f "migration: Append JSON description of migration
stream" needs a JSON writer. The existing qobject_to_json() wasn't a
good fit, because it requires building a QObject to convert. Instead,
migration got its very own JSON writer, in commit 190c882ce2 "QJSON:
Add JSON writer". It tacitly limits numbers to int64_t, and strings
contents to characters that don't need escaping, unlike
qobject_to_json().
The previous commit factored the JSON writer out of qobject_to_json().
Replace migration's JSON writer by it.
Cc: Juan Quintela <quintela@redhat.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20201211171152.146877-17-armbru@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Move the property types and property macros implemented in
qdev-properties-system.c to a new qdev-properties-system.h
header.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20201211220529.2290218-16-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
There is (mostly theoretical) race between removal of a scsi device and
scsi_dma_restart_bh.
It used to be easier to hit this race prior to my / Paulo's patch series
that added rcu to scsi bus device handling code, but IMHO this race
should still be possible to hit, at least in theory.
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=1854811
Fix it anyway with a patch that was proposed by Paulo in the above bugzilla.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20201210125929.1136390-2-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Linux has some OS-specific (and sometimes weird) mappings for various SCSI
statuses and sense codes. The most important is probably RESERVATION
CONFLICT. Add them so that they can be reported back to the guest
kernel.
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There is no "version 2" of the "Lesser" General Public License.
It is either "GPL version 2.0" or "Lesser GPL version 2.1".
This patch replaces all occurrences of "Lesser GPL version 2" with
"Lesser GPL version 2.1" in comment section.
This patch contains all the files, whose maintainer I could not get
from ‘get_maintainer.pl’ script.
Signed-off-by: Chetan Pant <chetan4windows@gmail.com>
Message-Id: <20201023124424.20177-1-chetan4windows@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
[thuth: Adapted exec.c and qdev-monitor.c to new location]
Signed-off-by: Thomas Huth <thuth@redhat.com>
Currently scsi_target_emulate_report_luns iterates over the child device list
twice, and there is no guarantee that this list is the same in both iterations.
The reason for iterating twice is that the first iteration calculates
how much memory to allocate. However if we use a dynamic array we can
avoid iterating twice, and therefore we avoid this race.
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=1866707
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20200913160259.32145-10-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20201006123904.610658-14-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This will help us to avoid the scsi device disappearing
after we took a reference to it.
It doesn't by itself forbid case when we try to access
an unrealized device
Suggested-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20200913160259.32145-9-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20201006123904.610658-13-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add scsi_device_get which finds the scsi device
and takes a reference to it.
Suggested-by: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20200913160259.32145-8-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20201006123904.610658-12-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The device core first places a device on the bus and then realizes it.
Make scsi_device_find avoid returing such devices to avoid
races in drivers that use an iothread (currently virtio-scsi)
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1812399
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20200913160259.32145-7-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20201006123904.610658-11-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20201006123904.610658-6-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This fixes the race between device emulation code that tries to find
a child device to dispatch the request to (e.g a scsi disk),
and hotplug of a new device to that bus.
Note that this doesn't convert all the readers of the list
but only these that might go over that list without BQL held.
This is a very small first step to make this code thread safe.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20200913160259.32145-5-mlevitsk@redhat.com>
[Use RCU_READ_LOCK_GUARD in more places, adjust testcase now that
the delay in DEVICE_DELETED due to RCU is more consistent. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20201006123904.610658-9-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This change will allow us to convert the bus children list to RCU,
while not changing the logic of this function
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20200913160259.32145-2-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
cur_mon really needs to be coroutine-local as soon as we move monitor
command handlers to coroutines and let them yield. As a first step, just
remove all direct accesses to cur_mon so that we can implement this in
the getter function later.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20201005155855.256490-4-kwolf@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Currently in 'megasas_map_sgl' when 'iov_count=0' will just return
success however the 'cmd' doens't contain any iov. This will cause
the assert in 'scsi_dma_complete' failed. This is because in
'dma_blk_cb' the 'dbs->sg_cur_index == dbs->sg->nsg' will be true
and just call 'dma_complete'. However now there is no aiocb returned.
This fixes the LP#1878263:
-->https://bugs.launchpad.net/qemu/+bug/1878263
Reported-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Li Qiang <liq3ea@163.com>
Message-Id: <20200815141940.44025-3-liq3ea@163.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The caller of 'megasas_map_sgl' will only check if the return
is zero or not. If it return 0 it means success, as in the next
patch we will consider 'iov_count=0' is an error, so let's
return -1 to indicate a failure.
Signed-off-by: Li Qiang <liq3ea@163.com>
Message-Id: <20200815141940.44025-2-liq3ea@163.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Several important steps during device scan depend on SCSI type of the
device. For example, max_transfer property is only determined and
assigned if the device has the type of TYPE_DISK.
Host-managed ZBC disks retain most of the properties of regular SCSI
drives, but they have their own SCSI device type, 0x14. This prevents
the proper assignment of max_transfer property for HM-zoned devices in
scsi-generic driver leading to I/O errors if the maximum i/o size
calculated at the guest exceeds the host value.
To fix this, define TYPE_ZBC to have the standard value from SCSI ZBC
standard spec. Several scan steps that were previously done only for
TYPE_DISK devices, are now performed for the SCSI devices having
TYPE_ZBC too.
Reported-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Message-Id: <20200811225122.17342-3-dmitry.fomichev@wdc.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Qemu will send GET_INFLIGHT_FD and SET_INFLIGH_FD to backend, and
the backend setup the inflight memory to track the io.
Change-Id: I805d6189996f7a1b44c65f0b12ef7473b1789510
Signed-off-by: Li Feng <fengli@smartx.com>
Message-Id: <20200909122021.1055174-1-fengli@smartx.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When debugging QEMU it is often useful to put a breakpoint on the
error_setg_internal method impl.
Unfortunately the object_property_add / object_class_property_add
methods call object_property_find / object_class_property_find methods
to check if a property exists already before adding the new property.
As a result there are a huge number of calls to error_setg_internal
on startup of most QEMU commands, making it very painful to set a
breakpoint on this method.
Most callers of object_find_property and object_class_find_property,
however, pass in a NULL for the Error parameter. This simplifies the
methods to remove the Error parameter entirely, and then adds some
new wrapper methods that are able to raise an Error when needed.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200914135617.1493072-1-berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Make the type checking macro name consistent with the TYPE_*
constant.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Message-Id: <20200902224311.1321159-40-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Some typedefs and macros are defined after the type check macros.
This makes it difficult to automatically replace their
definitions with OBJECT_DECLARE_TYPE.
Patch generated using:
$ ./scripts/codeconverter/converter.py -i \
--pattern=QOMStructTypedefSplit $(git grep -l '' -- '*.[ch]')
which will split "typdef struct { ... } TypedefName"
declarations.
Followed by:
$ ./scripts/codeconverter/converter.py -i --pattern=MoveSymbols \
$(git grep -l '' -- '*.[ch]')
which will:
- move the typedefs and #defines above the type check macros
- add missing #include "qom/object.h" lines if necessary
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-9-ehabkost@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-10-ehabkost@redhat.com>
Message-Id: <20200831210740.126168-11-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
We do not implement hotplug in the vscsi bus, but we forgot to
tell qdev about it. The result is that users are able to hotplug
devices in the vscsi bus, the devices appear in qdev, but they
aren't usable by the guest OS unless the user reboots it first.
Setting qbus hotplug_handler to NULL will tell qdev-monitor, via
qbus_is_hotpluggable(), that we do not support hotplug operations
in spapr_vscsi.
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1862059
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20200820190635.379657-1-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Use self-explicit definitions instead of magic '512' value.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Message-Id: <20200814082841.27000-8-f4bug@amsat.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
This will make future conversion to use OBJECT_DECLARE* easier.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Message-Id: <20200826184334.4120620-9-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This will make future conversion to OBJECT_DECLARE* easier.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-41-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Rename the PVSCSI_DEVICE_CLASS() and PVSCSI_DEVICE_GET_CLASS()
macros to be consistent with the PVSCSI() instance cast macro.
This will allow us to register the type cast macros using
OBJECT_DECLARE_TYPE later.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-4-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Rename the MEGASAS_DEVICE_CLASS() and MEGASAS_DEVICE_GET_CLASS()
macros to be consistent with the MEGASAS() instance cast macro.
This will allow us to register the type cast macros using
OBJECT_DECLARE_TYPE later.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-3-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Automatically size the number of virtio-scsi-pci, vhost-scsi-pci, and
vhost-user-scsi-pci request virtqueues to match the number of vCPUs.
Other transports continue to default to 1 request virtqueue.
A 1:1 virtqueue:vCPU mapping ensures that completion interrupts are
handled on the same vCPU that submitted the request. No IPI is
necessary to complete an I/O request and performance is improved. The
maximum number of MSI-X vectors and virtqueues limit are respected.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20200818143348.310613-6-stefanha@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The event and control virtqueues are always present, regardless of the
multi-queue configuration. Define a constant so that virtqueue number
calculations are easier to read.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Pankaj Gupta <pankaj.gupta.linux@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Message-Id: <20200818143348.310613-5-stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Meson doesn't enjoy the same flexibility we have with Make in choosing
the include path. In particular the tracing headers are using
$(build_root)/$(<D).
In order to keep the include directives unchanged,
the simplest solution is to generate headers with patterns like
"trace/trace-audio.h" and place forwarding headers in the source tree
such that for example "audio/trace.h" includes "trace/trace-audio.h".
This patch is too ugly to be applied to the Makefiles now. It's only
a way to separate the changes to the tracing header files from the
Meson rewrite of the tracing logic.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When migrate_add_blocker(blocker, &errp) is followed by
error_propagate(errp, err), we can often just as well do
migrate_add_blocker(..., errp).
Do that with this Coccinelle script:
@@
expression blocker, err, errp;
expression ret;
@@
- ret = migrate_add_blocker(blocker, &err);
- if (err) {
+ ret = migrate_add_blocker(blocker, errp);
+ if (ret < 0) {
... when != err;
- error_propagate(errp, err);
...
}
@@
expression blocker, err, errp;
@@
- migrate_add_blocker(blocker, &err);
- if (err) {
+ if (migrate_add_blocker(blocker, errp) < 0) {
... when != err;
- error_propagate(errp, err);
...
}
Double-check @err is not used afterwards. Dereferencing it would be
use after free, but checking whether it's null would be legitimate.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20200707160613.848843-43-armbru@redhat.com>
When all we do with an Error we receive into a local variable is
propagating to somewhere else, we can just as well receive it there
right away. Convert
if (!foo(..., &err)) {
...
error_propagate(errp, err);
...
return ...
}
to
if (!foo(..., errp)) {
...
...
return ...
}
where nothing else needs @err. Coccinelle script:
@rule1 forall@
identifier fun, err, errp, lbl;
expression list args, args2;
binary operator op;
constant c1, c2;
symbol false;
@@
if (
(
- fun(args, &err, args2)
+ fun(args, errp, args2)
|
- !fun(args, &err, args2)
+ !fun(args, errp, args2)
|
- fun(args, &err, args2) op c1
+ fun(args, errp, args2) op c1
)
)
{
... when != err
when != lbl:
when strict
- error_propagate(errp, err);
... when != err
(
return;
|
return c2;
|
return false;
)
}
@rule2 forall@
identifier fun, err, errp, lbl;
expression list args, args2;
expression var;
binary operator op;
constant c1, c2;
symbol false;
@@
- var = fun(args, &err, args2);
+ var = fun(args, errp, args2);
... when != err
if (
(
var
|
!var
|
var op c1
)
)
{
... when != err
when != lbl:
when strict
- error_propagate(errp, err);
... when != err
(
return;
|
return c2;
|
return false;
|
return var;
)
}
@depends on rule1 || rule2@
identifier err;
@@
- Error *err = NULL;
... when != err
Not exactly elegant, I'm afraid.
The "when != lbl:" is necessary to avoid transforming
if (fun(args, &err)) {
goto out
}
...
out:
error_propagate(errp, err);
even though other paths to label out still need the error_propagate().
For an actual example, see sclp_realize().
Without the "when strict", Coccinelle transforms vfio_msix_setup(),
incorrectly. I don't know what exactly "when strict" does, only that
it helps here.
The match of return is narrower than what I want, but I can't figure
out how to express "return where the operand doesn't use @err". For
an example where it's too narrow, see vfio_intx_enable().
Silently fails to convert hw/arm/armsse.c, because Coccinelle gets
confused by ARMSSE being used both as typedef and function-like macro
there. Converted manually.
Line breaks tidied up manually. One nested declaration of @local_err
deleted manually. Preexisting unwanted blank line dropped in
hw/riscv/sifive_e.c.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20200707160613.848843-35-armbru@redhat.com>
The previous commit enables conversion of
qdev_prop_set_drive_err(..., &err);
if (err) {
...
}
to
if (!qdev_prop_set_drive_err(..., errp)) {
...
}
Coccinelle script:
@@
identifier fun = qdev_prop_set_drive_err;
expression list args;
typedef Error;
Error *err;
@@
- fun(args, &err);
- if (err)
+ if (!fun(args, &err))
{
...
}
One line break tidied up manually.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20200707160613.848843-33-armbru@redhat.com>
The previous commit enables conversion of
foo(..., &err);
if (err) {
...
}
to
if (!foo(..., errp)) {
...
}
for QOM functions that now return true / false on success / error.
Coccinelle script:
@@
identifier fun = {
object_apply_global_props, object_initialize_child_with_props,
object_initialize_child_with_propsv, object_property_get,
object_property_get_bool, object_property_parse, object_property_set,
object_property_set_bool, object_property_set_int,
object_property_set_link, object_property_set_qobject,
object_property_set_str, object_property_set_uint, object_set_props,
object_set_propv, user_creatable_add_dict,
user_creatable_complete, user_creatable_del
};
expression list args, args2;
typedef Error;
Error *err;
@@
- fun(args, &err, args2);
- if (err)
+ if (!fun(args, &err, args2))
{
...
}
Fails to convert hw/arm/armsse.c, because Coccinelle gets confused by
ARMSSE being used both as typedef and function-like macro there.
Convert manually.
Line breaks tidied up manually.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20200707160613.848843-29-armbru@redhat.com>
The object_property_set_FOO() setters take property name and value in
an unusual order:
void object_property_set_FOO(Object *obj, FOO_TYPE value,
const char *name, Error **errp)
Having to pass value before name feels grating. Swap them.
Same for object_property_set(), object_property_get(), and
object_property_parse().
Convert callers with this Coccinelle script:
@@
identifier fun = {
object_property_get, object_property_parse, object_property_set_str,
object_property_set_link, object_property_set_bool,
object_property_set_int, object_property_set_uint, object_property_set,
object_property_set_qobject
};
expression obj, v, name, errp;
@@
- fun(obj, v, name, errp)
+ fun(obj, name, v, errp)
Chokes on hw/arm/musicpal.c's lcd_refresh() with the unhelpful error
message "no position information". Convert that one manually.
Fails to convert hw/arm/armsse.c, because Coccinelle gets confused by
ARMSSE being used both as typedef and function-like macro there.
Convert manually.
Fails to convert hw/rx/rx-gdbsim.c, because Coccinelle gets confused
by RXCPU being used both as typedef and function-like macro there.
Convert manually. The other files using RXCPU that way don't need
conversion.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20200707160613.848843-27-armbru@redhat.com>
[Straightforwad conflict with commit 2336172d9b "audio: set default
value for pcspk.iobase property" resolved]
Convert
foo(..., &err);
if (err) {
...
}
to
if (!foo(..., &err)) {
...
}
for qdev_realize(), qdev_realize_and_unref(), qbus_realize() and their
wrappers isa_realize_and_unref(), pci_realize_and_unref(),
sysbus_realize(), sysbus_realize_and_unref(), usb_realize_and_unref().
Coccinelle script:
@@
identifier fun = {
isa_realize_and_unref, pci_realize_and_unref, qbus_realize,
qdev_realize, qdev_realize_and_unref, sysbus_realize,
sysbus_realize_and_unref, usb_realize_and_unref
};
expression list args, args2;
typedef Error;
Error *err;
@@
- fun(args, &err, args2);
- if (err)
+ if (!fun(args, &err, args2))
{
...
}
Chokes on hw/arm/musicpal.c's lcd_refresh() with the unhelpful error
message "no position information". Nothing to convert there; skipped.
Fails to convert hw/arm/armsse.c, because Coccinelle gets confused by
ARMSSE being used both as typedef and function-like macro there.
Converted manually.
A few line breaks tidied up manually.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-Id: <20200707160613.848843-5-armbru@redhat.com>
qbus_set_hotplug_handler() is a simple wrapper around
object_property_set_link().
object_property_set_link() fails when the property doesn't exist, is
not settable, or its .check() method fails. These are all programming
errors here, so passing &error_abort to qbus_set_hotplug_handler() is
appropriate.
Most of its callers do. Exceptions:
* pcie_cap_slot_init(), shpc_init(), spapr_phb_realize() pass NULL,
i.e. they ignore errors.
* spapr_machine_init() passes &error_fatal.
* s390_pcihost_realize(), virtio_serial_device_realize(),
s390_pcihost_plug() pass the error to their callers. The latter two
keep going after the error, which looks wrong.
Drop the @errp parameter, and instead pass &error_abort to
object_property_set_link().
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Daniel P. Berrangé" <berrange@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20200630090351.1247703-15-armbru@redhat.com>
All callers pass &error_abort. Drop the parameter.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Daniel P. Berrangé" <berrange@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20200630090351.1247703-14-armbru@redhat.com>
Some tracepoints in megasas.c use a guest-controlled value as an index
into the mfi_frame_desc[] array. Thus a malicious guest could cause an
out-of-bounds error here. Fortunately, the impact is very low since this
can only happen when the corresponding tracepoints have been enabled
before, but the problem should be fixed anyway with a proper check.
Buglink: https://bugs.launchpad.net/qemu/+bug/1882065
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20200615072629.32321-1-thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
qdev_prop_set_drive() can fail. None of the other qdev_prop_set_FOO()
can; they abort on error.
To clean up this inconsistency, rename qdev_prop_set_drive() to
qdev_prop_set_drive_err(), and create a qdev_prop_set_drive() that
aborts on error.
Coccinelle script to update callers:
@ depends on !(file in "hw/core/qdev-properties-system.c")@
expression dev, name, value;
symbol error_abort;
@@
- qdev_prop_set_drive(dev, name, value, &error_abort);
+ qdev_prop_set_drive(dev, name, value);
@@
expression dev, name, value, errp;
@@
- qdev_prop_set_drive(dev, name, value, errp);
+ qdev_prop_set_drive_err(dev, name, value, errp);
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200622094227.1271650-14-armbru@redhat.com>
Several block device properties related to blocksize configuration must
be in certain relationship WRT each other: physical block must be no
smaller than logical block; min_io_size, opt_io_size, and
discard_granularity must be a multiple of a logical block.
To ensure these requirements are met, add corresponding consistency
checks to blkconf_blocksizes, adjusting its signature to communicate
possible error to the caller. Also remove the now redundant consistency
checks from the specific devices.
Signed-off-by: Roman Kagan <rvkagan@yandex-team.ru>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Message-Id: <20200528225516.1676602-3-rvkagan@yandex-team.ru>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This is the transformation explained in the commit before previous.
Takes care of just one pattern that needs conversion. More to come in
this series.
Coccinelle script:
@ depends on !(file in "hw/arm/highbank.c")@
expression bus, type_name, dev, expr;
@@
- dev = qdev_create(bus, type_name);
+ dev = qdev_new(type_name);
... when != dev = expr
- qdev_init_nofail(dev);
+ qdev_realize_and_unref(dev, bus, &error_fatal);
@@
expression bus, type_name, dev, expr;
identifier DOWN;
@@
- dev = DOWN(qdev_create(bus, type_name));
+ dev = DOWN(qdev_new(type_name));
... when != dev = expr
- qdev_init_nofail(DEVICE(dev));
+ qdev_realize_and_unref(DEVICE(dev), bus, &error_fatal);
@@
expression bus, type_name, expr;
identifier dev;
@@
- DeviceState *dev = qdev_create(bus, type_name);
+ DeviceState *dev = qdev_new(type_name);
... when != dev = expr
- qdev_init_nofail(dev);
+ qdev_realize_and_unref(dev, bus, &error_fatal);
@@
expression bus, type_name, dev, expr, errp;
symbol true;
@@
- dev = qdev_create(bus, type_name);
+ dev = qdev_new(type_name);
... when != dev = expr
- object_property_set_bool(OBJECT(dev), true, "realized", errp);
+ qdev_realize_and_unref(dev, bus, errp);
@@
expression bus, type_name, expr, errp;
identifier dev;
symbol true;
@@
- DeviceState *dev = qdev_create(bus, type_name);
+ DeviceState *dev = qdev_new(type_name);
... when != dev = expr
- object_property_set_bool(OBJECT(dev), true, "realized", errp);
+ qdev_realize_and_unref(dev, bus, errp);
The first rule exempts hw/arm/highbank.c, because it matches along two
control flow paths there, with different @type_name. Covered by the
next commit's manual conversions.
Missing #include "qapi/error.h" added manually.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-10-armbru@redhat.com>
[Conflicts in hw/misc/empty_slot.c and hw/sparc/leon3.c resolved]
Use unsigned type for the MegasasState fields which hold positive
numeric values.
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Reviewed-by: Darren Kenny <darren.kenny@oracle.com>
Message-Id: <20200513192540.1583887-4-ppandit@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
While in megasas_handle_frame(), megasas_enqueue_frame() may
set a NULL frame into MegasasCmd object for a given 'frame_addr'
address. Add check to avoid a NULL pointer dereference issue.
Reported-by: Alexander Bulekov <alxndr@bu.edu>
Fixes: https://bugs.launchpad.net/qemu/+bug/1878259
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Acked-by: Alexander Bulekov <alxndr@bu.edu>
Reviewed-by: Darren Kenny <darren.kenny@oracle.com>
Message-Id: <20200513192540.1583887-3-ppandit@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
A guest user may set 'reply_queue_head' field of MegasasState to
a negative value. Later in 'megasas_lookup_frame' it is used to
index into s->frames[] array. Use unsigned type to avoid OOB
access issue.
Also check that 'index' value stays within s->frames[] bounds
through the while() loop in 'megasas_lookup_frame' to avoid OOB
access.
Reported-by: Ren Ding <rding@gatech.edu>
Reported-by: Hanqing Zhao <hanqing@gatech.edu>
Reported-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Acked-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20200513192540.1583887-2-ppandit@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We use the Object type all over the place.
Forward declare it in "qemu/typedefs.h".
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200504115656.6045-2-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Mark Cave-Ayland
Hannes Reinecke
Paolo Bonzini
Peng Liang
Maxim Levitsky
Zihao Chang
Philippe Mathieu-Daudé
Kevin Wolf
Sergio Lopez
Peter Maydell
Markus Armbruster
Eduardo Habkost
Chetan Pant
Li Qiang
Dmitry Fomichev
Li Feng
Daniel P. Berrangé
Daniel Henrique Barboza
Stefan Hajnoczi
Marc-André Lureau
Thomas Huth
Roman Kagan
Prasad J Pandit