This doesn't require write access to the CPU structure.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <158941060817.240484.14621015211317485106.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
That "b" means "base address" and thus shouldn't be in the name
of actual entries and related constants.
This patch keeps the synthetic patb_entry field of the spapr
virtual hypervisor unchanged until I figure out if that has
an impact on the migration stream.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190215170029.15641-11-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
In target/ppc/mmu-hash64.c there already exists the function
ppc_hash64_get_phys_page_debug() to get the physical (real) address for
a given effective address in hash mode.
Implement the function ppc_radix64_get_phys_page_debug() to allow a real
address to be obtained for a given effective address in radix mode.
This is used when a debugger is attached to qemu.
Previously we just had a comment saying this is unimplemented which then
fell through to the default case and caused an abort due to
unrecognised mmu model as the default had no case for the V3 mmu, which
was misleading at best.
We reuse ppc_radix64_walk_tree() which is used by the radix fault
handler since the process of walking the radix tree is identical.
Reported-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
ISA V3.00 introduced a new radix mmu model. Implement the page fault
handler for this so we can run a tcg guest in radix mode and perform
address translation correctly.
In real mode (mmu turned off) addresses are masked to remove the top
4 bits and then are subject to partition scoped translation, since we only
support pseries at this stage it is only necessary to perform the masking
and then we're done.
In virtual mode (mmu turned on) address translation if performed as
follows:
1. Use the quadrant to determine the fully qualified address.
The fully qualified address is defined as the combination of the effective
address, the effective logical partition id (LPID) and the effective
process id (PID). Based on the quadrant (EA63:62) we set the pid and lpid
like so:
quadrant 0: lpid = LPIDR, pid = PIDR
quadrant 1: HV only (not allowed in pseries)
quadrant 2: HV only (not allowed in pseries)
quadrant 3: lpid = LPIDR, pid = 0
If we can't get the fully qualified address we raise a segment interrupt.
2. Find the guest radix tree
We ask the virtual hypervisor for the partition table which was registered
with H_REGISTER_PROC_TBL which points us to the process table in guest
memory. We then index this table by pid to get the process table entry
which points us to the appropriate radix tree to translate the address.
If the process table isn't big enough to contain an entry for the current
pid then we raise a storage interrupt.
3. Walk the radix tree
Next we walk the radix tree where each level is a table of page directory
entries indexed by some number of bits from the effective address, where
the number of bits is determined by the table size. We continue to walk
the tree (while entries are valid and the table is of minimum size) until
we reach a table of page table entries, indicated by having the leaf bit
set. The appropriate pte is then checked for sufficient access permissions,
the reference and change bits are updated and the real address is
calculated from the real page number bits of the pte and the low bits of
the effective address.
If we can't find an entry or can't access the entry bacause of permissions
then we raise a storage interrupt.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
[dwg: Add missing parentheses to macro]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
