Use MAKE_64BIT_MASK instead of open-coding. Remove an odd
vector size check that is unlikely to be more profitable
than 3 64-bit integer stores. Correct the iteration for WORD
to avoid writing too much data.
Fixes RISU tests of PTRUE for VL 256.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20180705191929.30773-3-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Normally this is automatic in the size restrictions that are placed
on vector sizes coming from the implementation. However, for the
legitimate size tuple [oprsz=8, maxsz=32], we need to clear the final
24 bytes of the vector register. Without this check, do_dup selects
TCG_TYPE_V128 and clears only 16 bytes.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20180705191929.30773-2-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
These instructions must perform the sve_access_check, but
since they are implemented as NOPs there is no generated
code to elide when the access check fails.
Fixes: Coverity issues 1393780 & 1393779.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If the CMSDK APB timer is set up with a zero RELOAD value
then it will count down to zero, fire once and then stay
at zero. From the point of view of the ptimer system, the
timer is disabled; but the enable bit in the CTRL register
is still set and if the guest subsequently writes to the
RELOAD or VALUE registers this should cause the timer to
start counting down again.
Add code to the write paths for RELOAD and VALUE so that
we correctly restart the timer in this situation.
Conversely, if the new RELOAD and VALUE are both zero,
we should stop the ptimer.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 20180703171044.9503-5-peter.maydell@linaro.org
The CMSDK APB timer is currently always configured as periodic timer.
This results in the following messages when trying to boot Linux.
Timer with delta zero, disabling
If the timer limit set with the RELOAD command is 0, the timer
needs to be enabled as one-shot timer.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The CMSDK timer interrupt triggers when the counter goes from 1 to 0,
so we want to trigger immediately, rather than waiting for a
clock cycle. Drop the incorrect NO_IMMEDIATE_TRIGGER setting.
We also do not want to get an interrupt if the guest sets the
counter directly to zero, so use the new TRIGGER_ONLY_ON_DECREMENT
policy.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 20180703171044.9503-3-peter.maydell@linaro.org
The CMSDK timer behaviour is that an interrupt is triggered when the
counter counts down from 1 to 0; however one is not triggered if the
counter is manually set to 0 by a guest write to the counter register.
Currently ptimer can't handle this; add a policy option to allow
a ptimer user to request this behaviour.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 20180703171044.9503-2-peter.maydell@linaro.org
smmu_iommu_mr() aims at returning the IOMMUMemoryRegion corresponding
to a given sid. The function extracts both the PCIe bus number and
the devfn to return this data. Current computation of devfn is wrong
as it only returns the PCIe function instead of slot | function.
Fixes 32cfd7f39e ("hw/arm/smmuv3: Cache/invalidate config data")
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1530775623-32399-1-git-send-email-eric.auger@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Here's a final pull request before tomorrow's hard freeze.
There are a number of fixes and improvements to the sm501 display
driver (not strictly ppc related, but used only on ppc and SH).
There's also a handful of unrelated fixes.
Whether all the sm501 changes are bugfixes is somewhat debatable, but
Peter has indicated he's ok with merging those for 3.0.
-----BEGIN PGP SIGNATURE-----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=3f0D
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-3.0-20180709' into staging
ppc patch queue 2018-07-09
Here's a final pull request before tomorrow's hard freeze.
There are a number of fixes and improvements to the sm501 display
driver (not strictly ppc related, but used only on ppc and SH).
There's also a handful of unrelated fixes.
Whether all the sm501 changes are bugfixes is somewhat debatable, but
Peter has indicated he's ok with merging those for 3.0.
# gpg: Signature made Mon 09 Jul 2018 08:42:15 BST
# gpg: using RSA key 6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>"
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-3.0-20180709:
sam460ex: Make sam460ex_load_device_tree() handle all errors internally
sam460ex: Don't check for errors from qemu_fdt_*()
sam460ex: Check for errors from libfdt functions
sam460ex: Update u-boot-sam460ex firmware
ppc: fix default VGA display for PReP machines
target/ppc: fix build on ppc64 host
ppc440_uc: Fix a copy/paste error
sm501: Set updated region dirty after 2D operation
sm501: Fix support for non-zero frame buffer start address
sm501: Log unimplemented raster operation modes
sm501: Implement negated destination raster operation mode
sm501: Use values from the pitch register for 2D operations
sm501: Perform a full update after palette change
sm501: Implement i2c part for reading monitor EDID
spapr/vio: quiet down the "irq" property accessors
ppc: fix default VGA display for Mac machines
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
sam460ex_load_device_tree() handles nearly all possible errors by simply
exiting (within helper functions and macros). It handles two early error
cases by returning an error.
There's no particular point to this, so make it handle those directly as
well, removing the need for the caller to handle a failure. As a bonus it
gives us more specific error messages.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The qemu_fdt_*() helper functions already exit with a message instead of
returning errors, so we don't need to check for errors in the caller.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
In a couple of places sam460ex_load_device_tree() calls "raw" libfdt
functions which can fail, but doesn't check for error codes. At best,
if these fail the guest will be silently started in a non-standard state,
or it could fail entirely.
Fix this by using the _FDT() helper macro which aborts on a libfdt failure.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Update the submodule and u-boot-sam460-20100605.bin to include
following fixes from Sebastian Bauer:
- Fix build with newer gcc
- Decrease unnecessary delay which fixes slow booting from CD
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Call nbd_co_send_extents() with correct length parameter
(extent.length may be smaller than original length).
Also, switch length parameter type to uint32_t, to correspond with
request->len and similar nbd_co_send_bitmap().
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20180704112302.471456-2-vsementsov@virtuozzo.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
Commit 29f9cef "ppc: Include vga cirrus card into the compiling process"
changed the default display adapter for all PPC machines to cirrus. Unfortunately
it missed setting the default display type to stdvga for both PReP machines
causing the display to fail to initialise under OpenHackWare.
Update the MachineClass for both prep and 40p machines so that the default
std(vga) display adapter is the default if no options are specified
which fixes the display for the PReP machines.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When I try to build a ppc64 target on a ppc64 host (gcc 8.1.1), I have:
.../target/ppc/int_helper.c: In function 'helper_vinsertb':
.../target/ppc/int_helper.c:1954:32: error: array subscript 18446744073709551608 is above array bounds of 'uint8_t[16]' {aka 'unsigned char[16]'} [-Werror=array-bounds]
memmove(&r->u8[index], &b->u8[8 - sizeof(r->element)], \
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
.../target/ppc/int_helper.c:1965:1: note: in expansion of macro 'VINSERT'
If we compare with the macro for ppc64le, we can see
sizeof(r->element[0]) should be used instead of sizeof(r->element).
And VINSERT uses only u8, u16, u32 and u64, so the maximum value
of sizeof(r->element[0]) is 8
Suggested-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Set the changed memory region dirty after performed a 2D operation to
ensure that the screen is updated properly.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Display updates and drawing hardware cursor did not work when frame
buffer address was non-zero. Fix this by taking the frame buffer
address into account in these cases. This fixes screen dragging on
AmigaOS. Based on patch by Sebastian Bauer.
Signed-off-by: Sebastian Bauer <mail@sebastianbauer.info>
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The sm501 currently implements only a very limited set of raster operation
modes. After this change, unknown raster operation modes are logged so
these can be easily spotted.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Add support for the negated destination operation mode. This is used e.g.
by AmigaOS for the INVERSEVID drawing mode. With this change, the cursor
in the shell and non-immediate window adjustment are working now.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Before, crt_h_total was used for src_width and dst_width. This is a
property of the current display setting and not relevant for the 2D
operation that also can be done off-screen. The pitch register's purpose
is to describe line pitch relevant of the 2D operation.
Signed-off-by: Sebastian Bauer <mail@sebastianbauer.info>
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Changing the palette of a color index has as an immediate effect on
all pixels with the corresponding index on real hardware. Performing a
full update after a palette change is a simple way to emulate this
effect.
Signed-off-by: Sebastian Bauer <mail@sebastianbauer.info>
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Emulate the i2c part of SM501 which is used to access the EDID info
from a monitor.
The vmstate structure is changed and its version is increased but
SM501 is only used on SH and PPC sam460ex machines that don't support
cross-version migration.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
commit efe2add7cb ("spapr/vio: deprecate the "irq" property")
introduced get/set accessors for the "irq" property to warn of its
usage, but the warning in the get pollutes the monitor 'info qtree'.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Commit 29f9cef39e "ppc: Include vga cirrus card into the compiling process"
changed the default display adapter for all PPC machines to cirrus. Unfortunately
it missed setting the default display type to stdvga for both Mac machines
causing the display to fail to initialise under OpenBIOS.
Update the MachineClass for both Old World and New World Macs so that the
default std(vga) display adapter is the default if no options are specified
which fixes the display for the Mac machines.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The mechanism to find possible type tokens can sometimes be confused and go into an
infinite loop. This happens for example in QEMU for a line that looks like
uint## BITS ##_t S = _S, T = _T; \
uint## BITS ##_t as, at, xs, xt, xd; \
Because the token pasting operator does not have a space before _t, it does not
match $notPermitted. However, (?x) is turned on in the regular expression for
modifiers, and thus ##_t matches the empty string. As a result, annotate_values
goes in an infinite loop.
The solution is simply to remove token pasting operators from the string before
looking for modifiers. In the example above, the string uintBITS_t will be
evaluated as a candidate modifier. This is not optimal, but it works as long
as people do not write things like a##s##m, and it fits nicely into sub
possible.
For a similar reason, \# should be rejected always, even if it is not
at end of line or followed by whitespace.
The same patch was sent to the Linux kernel mailing list.
Reported-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The vector cannot be negative. Coverity now reports this because it sees an
array access before the check, in ioapic_stat_update_irq.
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In the tcp_chr_write function, we checked errno,
but errno was not reset before a read or write operation.
Therefore, this check of errno's actions is often
incorrect after EAGAIN has occurred.
we need check errno together with ret < 0.
Signed-off-by: xinhua.Cao <caoxinhua@huawei.com>
Message-Id: <20180704033642.15996-1-caoxinhua@huawei.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Fixes: 9fc53a10f8
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since commit d6dcc5583e, '-cpu ?' shows the description of the
X86_CPU_TYPE_NAME("max") for the host CPU model:
Enables all features supported by the accelerator in the current host
instead of the expected:
KVM processor with all supported host features
or
HVF processor with all supported host features
This is caused by the early use of kvm_enabled() and hvf_enabled() in
a class_init function. Since the accelerator isn't configured yet, both
helpers return false unconditionally.
A QEMU binary will only be compiled with one of these accelerators, not
both. The appropriate description can thus be decided at build time.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <153055056654.212317.4697363278304826913.stgit@bahia.lan>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Some devices (like nvic in armv7m) are not accessable through
address_space_memory, therefore can not be tested with qtest.
Signed-off-by: Julia Suvorova <jusual@mail.ru>
Message-Id: <20180702065237.27899-1-jusual@mail.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When reviewing Paolo's pr-helper patches I've noticed couple of
problems:
1) socket_path needs to be calculated at two different places
(one for printing out help, the other if socket activation is NOT
used),
2) even though the default socket_path is allocated in
compute_default_paths() it is the only default path the function
handles. For instance, pidfile is allocated outside of this
function. And yet again, at different places than 1)
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Message-Id: <c791ba035f26ea957e8f3602e3009b621769b1ba.1530611283.git.mprivozn@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
After reading a PR IN command with zero request size in prh_read_request,
the resp->result field will be uninitialized and the resp.sz field will
be also uninitialized when returning to prh_co_entry.
If resp->result == GOOD (from a previous successful reply or just luck),
then the assert in prh_write_response might not be triggered and
uninitialized response will be sent.
The fix is to remove the whole handling of sz == 0 in prh_co_entry.
Those errors apply only to PR OUT commands and it's perfectly okay to
catch them later in do_pr_out and multipath_pr_out; the check for
too-short parameters in fact doesn't apply in the easy SG_IO case, as
it can be left to the target firmware even.
The result is that prh_read_request does not fail requests anymore and
prh_co_entry becomes simpler.
Reported-by: Dima Stepanov <dimastep@yandex-team.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
PPC tcg seems to be failing migration tests quite regularly;
we believe this is TCG bugs in dirty bit updating; it's
not clear why PPC fails more but lets skip for the moment.
$ ./tests/migration-test
/ppc64/migration/deprecated: OK
/ppc64/migration/bad_dest: Skipping test: kvm_hv not available OK
/ppc64/migration/postcopy/unix: Skipping test: kvm_hv not available OK
/ppc64/migration/precopy/unix: Skipping test: kvm_hv not available OK
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Message-id: 20180706143105.93472-1-dgilbert@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This series has three tasks:
1. To convert the SiFive U and E machines into SoCs and boards
2. To connect the Cadence GEM device to the SiFive U board
3. Fix some device tree problems with the SiFive U board
After this series the SiFive E and U boards have their SoCs split into
seperate QEMU objects, which can be used on future boards if desired.
The RISC-V Virt and Spike boards have not been converted. They haven't
been converted as they aren't physical boards, so it doesn't make a
whole lot of sense to split them into an SoC and board. The only
disadvantage with this is that they now differ to the SiFive boards.
This series also connect the Cadence GEM device to the SiFive U board.
There are some interrupt line changes requried before this is possible.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9sSsRtSTSGjTuM6PIeENKd+XcFQFAls+wyEACgkQIeENKd+X
cFQ6aAf+L70WdK9yznSHz2yyg6y+ElzaVAvEAPV6dqp/axI28RngirpmFGjn9XJX
5Z2000xoAbAdY4CsPRhYTNhCZ1yYeL1CWByt827LJhOji1oz6HZF3JZmECghU9A0
LPTIF58U5bKRjlG+qQxvdNn5WtFA+o5YrE8R1VpkYXNOcwCszI3MMf2gLOQRrOW3
ZYC15EaIsmwzbnhQiDMzKx4x3TNg4A1qGMkGGf6HLu0tg+sMwsxmTjAOxPAblFnp
7T66Kx+zwAFCQMyIgLGq2bGXae6nUWWTh5P/Mtlll/kBIv9uVujLZlCj0Ndb0wZi
ejptUPFJr4Kr5gE8qtG+Rueb+pGWHg==
=Op/V
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/alistair/tags/pull-riscv-pull-20180705' into staging
RISC-V: SoCify SiFive boards and connect GEM
This series has three tasks:
1. To convert the SiFive U and E machines into SoCs and boards
2. To connect the Cadence GEM device to the SiFive U board
3. Fix some device tree problems with the SiFive U board
After this series the SiFive E and U boards have their SoCs split into
seperate QEMU objects, which can be used on future boards if desired.
The RISC-V Virt and Spike boards have not been converted. They haven't
been converted as they aren't physical boards, so it doesn't make a
whole lot of sense to split them into an SoC and board. The only
disadvantage with this is that they now differ to the SiFive boards.
This series also connect the Cadence GEM device to the SiFive U board.
There are some interrupt line changes requried before this is possible.
# gpg: Signature made Fri 06 Jul 2018 02:17:21 BST
# gpg: using RSA key 21E10D29DF977054
# gpg: Good signature from "Alistair Francis <alistair@alistair23.me>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: F6C4 AC46 D493 4868 D3B8 CE8F 21E1 0D29 DF97 7054
* remotes/alistair/tags/pull-riscv-pull-20180705:
hw/riscv/sifive_u: Connect the Cadence GEM Ethernet device
hw/riscv/sifive_u: Move the uart device tree node under /soc/
hw/riscv/sifive_u: Set the interrupt controller number of interrupts
hw/riscv/sifive_u: Set the soc device tree node as a simple-bus
hw/riscv/sifive_plic: Use gpios instead of irqs
hw/riscv/sifive_e: Create a SiFive E SoC object
hw/riscv/sifive_u: Create a SiFive U SoC object
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Connect the Cadence GEM ethernet device. This also requires us to
expose the plic interrupt lines.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Michael Clark <mjc@sifive.com>
Set the interrupt-controller ndev to the correct number taken from the
HiFive Unleashed board.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Michael Clark <mjc@sifive.com>
To allow Linux to ennumerate devices on the /soc/ node set it as a
"simple-bus".
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Michael Clark <mjc@sifive.com>
Instead of creating the interrupt in lines with qemu_allocate_irq() use
qdev_init_gpio_in() as this gives us the ability to use the qdev*gpio*()
helpers later on.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Suggested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Michael Clark <mjc@sifive.com>
Create a SiFive Unleashed U54 SoC and use that in the sifive_u machine.
We leave the SoC, RAM, device tree and reset/fdt loading as part of the
machine. All the other device creation has been moved to the SoC.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Michael Clark <mjc@sifive.com>
We can't use cross compilers in the current Debian stable and Debian
sid is sketchy as hell. So for powerpc fall back to dog-fooding our
own linux-user to do the build.
As we can only build the base image with a suitably configured
source tree we fall back to checking for its existence when we can't
build it from scratch. However this does mean you don't have to keep
a static powerpc-linux-user in your active configuration just to
update the cross build image.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
We might as well have a custom rule for this. For one thing the
dependencies are different. As the primary dependency for
docker-image-% could never be docker-image-debian-bootstrap we can
drop that test in the main rule as well.
Missing EXECUTABLE, DEB_ARCH and DEB_TYPE are treated as hard faults
now. We also error out if the EXECUTABLE file isn't there. We should
really do this with a dependency on any source rules but currently
subdir-FOO-linux-user isn't enough on a clean build.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
These will have been build with debootstrap so we need to check
against the debian-bootstrap dockerfile. This does mean sticking to
debian-FOO-user as the naming conventions for boot-strapped images.
The actual cross image is built on top.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
