aspeed_smc_is_implemented() filters invalid registers in a peculiar
way. Let's remove it and open code the if conditions. It serves the
same purpose, the aesthetic is better, and new registers can easily be
added.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1467994016-11678-3-git-send-email-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Each controller on the ast2400 has a memory range on which it maps its
flash module slaves. Each slave is assigned a memory segment for its
mapping that can be changed at bootime with the Segment Address
Register. This is not supported in the current implementation so we
are using the defaults provided by the specs.
Each SPI flash slave can then be accessed in two modes: Command and
User. When in User mode, accesses to the memory segment of the slaves
are translated in SPI transfers. When in Command mode, the HW
generates the SPI commands automatically and the memory segment is
accessed as if doing a MMIO. Other SPI controllers call that mode
linear addressing mode.
For this purpose, we are adding below each crontoller an array of
structs gathering for each SPI flash module, a segment rank, a
MemoryRegion to handle the memory accesses and the associated SPI
slave device, which should be a m25p80.
Only the User mode is supported for now but we are preparing ground
for the Command mode. The framework is sufficient to support Linux.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1467138270-32481-8-git-send-email-clg@kaod.org
[PMM: Use g_new0() rather than g_malloc0()]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Aspeed AST2400 soc includes a static memory controller for the BMC
which supports NOR, NAND and SPI flash memory modules. This controller
has two modes : the SMC for the legacy interface which supports only
one module and the FMC for the new interface which supports up to five
modules. The AST2400 also includes a SPI only controller used for the
host firmware, commonly called BIOS on Intel. It can be used in three
mode : a SPI master, SPI slave and SPI pass-through
Below is the initial framework for the SMC controller (FMC mode only)
and the SPI controller: the sysbus object, MMIO for registers
configuration and controls. Each controller has a SPI bus and a
configurable number of CS lines for SPI flash slaves.
The differences between the controllers are small, so they are
abstracted using indirections on the register numbers.
Only SPI flash modules are supported.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1467138270-32481-7-git-send-email-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: added one missing error_propagate]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This enables qemu to handle late inits and report errors. All the SSI
slave routine names were changed accordingly. Code was modified to
handle errors when possible (m25p80 and ssi-sd)
Tested with the m25p80 slave object.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1467138270-32481-2-git-send-email-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-38-git-send-email-peter.maydell@linaro.org
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-36-git-send-email-peter.maydell@linaro.org
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-13-git-send-email-peter.maydell@linaro.org
Separate out the XilinxSPIPS struct into a separate header
file.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Move the ssi.h include file into the ssi directory.
While touching the code also fix the typdef lines as
checkpatch complains.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
To properly indicate they are unconnected.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
To get it out of the default GPIO list. This allows child devices to
use the un-named GPIO namespace without having to be SSI aware. That
is, there is no more need for machines to know about the obscure
policy where GPIO 0 is the SSI chip-select and GPIO 1..N are the
concrete class GPIOs (defined locally as 0..N-1).
This is most notable in stellaris, which uses a device which has both
SSI and concrete level GPIOs.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
After commit 767adce2d, they are redundant. This way we don't assign them
except when needed. Once there, there were lots of cases where the ".fields"
indentation was wrong:
.fields = (VMStateField []) {
and
.fields = (VMStateField []) {
Change all the combinations to:
.fields = (VMStateField[]){
The biggest problem (apart from aesthetics) was that checkpatch complained
when we copy&pasted the code from one place to another.
Signed-off-by: Juan Quintela <quintela@redhat.com>
[PMM: fixed minor conflict, corrected commit message typos]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
CVE-2013-4530
pl022.c did not bounds check tx_fifo_head and
rx_fifo_head after loading them from file and
before they are used to dereference array.
Reported-by: Michael S. Tsirkin <mst@redhat.com
Reported-by: Anthony Liguori <anthony@codemonkey.ws>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Remove two legacy ->qbus style casts from TYPE_SSI_BUS to TYPE_BUS in
ssi.c.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
[AF: Convert one missing ->qbus and rename parent field]
Signed-off-by: Andreas Färber <afaerber@suse.de>
Convert legacy ->qdev style casts from TYPE_SSI_SLAVE to TYPE_DEVICE.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
[AF: Introduce local DeviceState variable for transition to QOM realize]
Signed-off-by: Andreas Färber <afaerber@suse.de>
The LQSPI bus attachment supports byte/halfword and misaligned
accesses. Fixed. Refactored the LQSPI cache to be byte-wise
instead of word wise accordingly.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Message-id: 5ec47b13563ad2d22105a1f26186d7756718394b.1369117359.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Do 16 words per fifo flush. Increases performance and decreases
debug verbosity. This data depth has no real hardware analogue,
so just go with something that has reasonable performance.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Message-id: 5621ee4621941d3639b5cacfdec26bd3148f31d5.1369117359.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The debug printfs on every SPI operation is extremely verbose. Add
a second level of debug for this.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Message-id: f63478b8e5b29cc011cdc10e29f8537bb2fc2b5e.1369117359.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is worth keeping track of when debugging the device model.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Message-id: d3b44ecf23d671798b062eee5dc362c716ea54cd.1369117359.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The QSPI controller was using byte-wide stripes when striping across
the two flashes in dual parallel mode. The real hardware however uses
individual bit striping. QEMU misbehaves in the (corner) case where
data is written/read in dual-parallel mode and read/written back in
single mode.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Message-id: 718a61df1bf746ec06f6da44d12f8317af7b08ce.1369117359.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The CTRL register was RAZ/WI on some of the RW bits. Even though the
function behind these bits is invalid in QEMU, they should still be
guest accessible. Fix.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Message-id: b7aaad93163ce4af0c428635804ac7b77a567b25.1369117359.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The LQSPI mode is supposed to work via the automatic CS mode feature
rather than manipulate CS lines itself. Now that auto CS is implemented
remove LQSPIs CS mode override logic. There is still a need to
manipulate the U_PAGE bit in LQSPI config register to implement
dual-stack mode however.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Message-id: 000c8dd54df09523f17052638100722ef0f5a3af.1369117359.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement the automatic CS control feature. If the MANUAL_CS bit is
cleared then the chip select stay de-asserted as long as the tx FIFO
is empty.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Message-id: 1d67383adc42761af715a93f161344b9284dfc9a.1369117359.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
SPI has a mode where it automatically starts based on tx fifo
occupancy. Implemented.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Message-id: f4e9accb5de87b526fff6ed937f63278db76533b.1369117359.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Invalidate the LQSPI cached page when transitioning into LQSPI mode.
Otherwise there is a possibility that the controller will return stale
data to the guest when transitioning back to LQ_MODE after a page
program.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Message-id: 677490a6ee1953fe5d366e599d665de645ac84db.1369117359.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
QSPI has a bigger FIFO than the regular SPI controller. Differentiate
between the two with correct FIFO sizes for each.
This is the first piece of class data for SPIPS, so this patch sees
the creation of the XilinxSPIPSClass definition and assoicated QOM
constructs.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Message-id: acee25dd5e203215cbc15ca5d3cb5d5b2efebe7b.1369117359.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
You really need this is you want to track a guest banging on LQSPI.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Message-id: 26e508da4af11058d37daa777064c9e5c2a69abb.1369117359.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The real hardware does not produce interrupts in LQSPI mode. Inhibit
generation of interrupts when the LQ_MODE bit is set.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Message-id: dff794a06872009ea7e5733ce6adcff94d18bbd0.1369117359.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
By default these interrupts are clear on read.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Message-id: 999ff0091ed3cc3969a431bf55c00ef934cecc8e.1369117359.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Make SPI and QSPI different classes. QSPIPS is setup as a child of SPIPS.
Only QSPI has the LQSPI functionality, so move all that to the child class.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Message-id: 2cdd0cadb5ba77ca02fde5cae627852dc9a64c71.1369117359.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
