The armv7m systick timer is a 24-bit decrementing, wrap-on-zero,
clear-on-write counter. Our current implementation has various
bugs and dubious workarounds in it (for instance see
https://bugs.launchpad.net/qemu/+bug/1872237).
We have an implementation of a simple decrementing counter
and we put a lot of effort into making sure it handles the
interesting corner cases (like "spend a cycle at 0 before
reloading") -- ptimer.
Rewrite the systick timer to use a ptimer rather than
a raw QEMU timer.
Unfortunately this is a migration compatibility break,
which will affect all M-profile boards.
Among other bugs, this fixes
https://bugs.launchpad.net/qemu/+bug/1872237 :
now writes to SYST_CVR when the timer is enabled correctly
do nothing; when the timer is enabled via SYST_CSR.ENABLE,
the ptimer code will (because of POLICY_NO_IMMEDIATE_RELOAD)
arrange that after one timer tick the counter is reloaded
from SYST_RVR and then counts down from there, as the
architecture requires.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201015151829.14656-3-peter.maydell@linaro.org
The watchdog is part of NPCM7XX's timer module. Its behavior is
controlled by the WTCR register in the timer.
When enabled, the watchdog issues an interrupt signal after a pre-set
amount of cycles, and issues a reset signal shortly after that.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: deleted blank line at end of npcm_watchdog_timer-test.c]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This peripheral has 1 free-running timer and 4 compare registers.
Only the free-running timer is implemented. Add support the
COMPARE registers (each register is wired to an IRQ).
Reference: "BCM2835 ARM Peripherals" datasheet [*]
chapter 12 "System Timer":
The System Timer peripheral provides four 32-bit timer channels
and a single 64-bit free running counter. Each channel has an
output compare register, which is compared against the 32 least
significant bits of the free running counter values. When the
two values match, the system timer peripheral generates a signal
to indicate a match for the appropriate channel. The match signal
is then fed into the interrupt controller.
This peripheral is used since Linux 3.7, commit ee4af5696720
("ARM: bcm2835: add system timer").
[*] https://www.raspberrypi.org/app/uploads/2012/02/BCM2835-ARM-Peripherals.pdf
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-id: 20201010203709.3116542-4-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The variable holding the CTRL_STATUS register is misnamed
'status'. Rename it 'ctrl_status' to make it more obvious
this register is also used to control the peripheral.
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201010203709.3116542-3-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use the BCM2835_SYSTIMER_COUNT definition instead of the
magic '4' value.
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201010203709.3116542-2-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The NPCM730 and NPCM750 SoCs have three timer modules each holding five
timers and some shared registers (e.g. interrupt status).
Each timer runs at 25 MHz divided by a prescaler, and counts down from a
configurable initial value to zero. When zero is reached, the interrupt
flag for the timer is set, and the timer is disabled (one-shot mode) or
reloaded from its initial value (periodic mode).
This implementation is sufficient to boot a Linux kernel configured for
NPCM750. Note that the kernel does not seem to actually turn on the
interrupts.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Message-id: 20200911052101.2602693-4-hskinnemoen@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some typedefs and macros are defined after the type check macros.
This makes it difficult to automatically replace their
definitions with OBJECT_DECLARE_TYPE.
Patch generated using:
$ ./scripts/codeconverter/converter.py -i \
--pattern=QOMStructTypedefSplit $(git grep -l '' -- '*.[ch]')
which will split "typdef struct { ... } TypedefName"
declarations.
Followed by:
$ ./scripts/codeconverter/converter.py -i --pattern=MoveSymbols \
$(git grep -l '' -- '*.[ch]')
which will:
- move the typedefs and #defines above the type check macros
- add missing #include "qom/object.h" lines if necessary
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-9-ehabkost@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-10-ehabkost@redhat.com>
Message-Id: <20200831210740.126168-11-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Move typedef closer to the type check macros, to make it easier
to convert the code to OBJECT_DEFINE_TYPE() in the future.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-19-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The macro definition had an extra semicolon. This was never
noticed because the macro was only being used where it didn't
make a difference.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-11-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
These were designed to facilitate testing but should provide enough
function to be useful in other contexts. Only a subset of the functions
of each peripheral is implemented, mainly due to the lack of a standard
way to handle electrical connections (like GPIO pins).
[AM: Remove word 'Atmel' from filenames and all elements of code]
Suggested-by: Aleksandar Markovic <aleksandar.m.mail@gmail.com>
Signed-off-by: Sarah Harris <S.E.Harris@kent.ac.uk>
Signed-off-by: Ed Robbins <E.J.C.Robbins@kent.ac.uk>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
[rth: Squash info mtree fixes and a file rename from f4bug]
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
[PMD: Use qemu_log_mask(LOG_UNIMP), replace goto by return]
Signed-off-by: Aleksandar Markovic <aleksandar.m.mail@gmail.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Thomas Huth <huth@tuxfamily.org>
Message-Id: <20200705140315.260514-21-huth@tuxfamily.org>
[PMD: Check cpu-frequency-hz property in realize()]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
renesas_cmt: 16bit compare match timer modules.
This part use many renesas's CPU.
Hardware manual.
https://www.renesas.com/us/en/doc/products/mpumcu/doc/rx_family/r01uh0033ej0140_rx62n.pdf
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20200224141923.82118-16-ysato@users.sourceforge.jp>
[PMD: Split from TMR, filled VMStateField for migration]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
renesas_tmr: 8bit timer modules.
This part use many renesas's CPU.
Hardware manual.
https://www.renesas.com/us/en/doc/products/mpumcu/doc/rx_family/r01uh0033ej0140_rx62n.pdf
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20200224141923.82118-16-ysato@users.sourceforge.jp>
[PMD: Split from CMT, filled VMStateField for migration]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Extract timer definitions to 'hw/timer/tmu012.h'.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This is the transformation explained in the commit before previous.
Takes care of just one pattern that needs conversion. More to come in
this series.
Coccinelle script:
@ depends on !(file in "hw/arm/highbank.c")@
expression bus, type_name, dev, expr;
@@
- dev = qdev_create(bus, type_name);
+ dev = qdev_new(type_name);
... when != dev = expr
- qdev_init_nofail(dev);
+ qdev_realize_and_unref(dev, bus, &error_fatal);
@@
expression bus, type_name, dev, expr;
identifier DOWN;
@@
- dev = DOWN(qdev_create(bus, type_name));
+ dev = DOWN(qdev_new(type_name));
... when != dev = expr
- qdev_init_nofail(DEVICE(dev));
+ qdev_realize_and_unref(DEVICE(dev), bus, &error_fatal);
@@
expression bus, type_name, expr;
identifier dev;
@@
- DeviceState *dev = qdev_create(bus, type_name);
+ DeviceState *dev = qdev_new(type_name);
... when != dev = expr
- qdev_init_nofail(dev);
+ qdev_realize_and_unref(dev, bus, &error_fatal);
@@
expression bus, type_name, dev, expr, errp;
symbol true;
@@
- dev = qdev_create(bus, type_name);
+ dev = qdev_new(type_name);
... when != dev = expr
- object_property_set_bool(OBJECT(dev), true, "realized", errp);
+ qdev_realize_and_unref(dev, bus, errp);
@@
expression bus, type_name, expr, errp;
identifier dev;
symbol true;
@@
- DeviceState *dev = qdev_create(bus, type_name);
+ DeviceState *dev = qdev_new(type_name);
... when != dev = expr
- object_property_set_bool(OBJECT(dev), true, "realized", errp);
+ qdev_realize_and_unref(dev, bus, errp);
The first rule exempts hw/arm/highbank.c, because it matches along two
control flow paths there, with different @type_name. Covered by the
next commit's manual conversions.
Missing #include "qapi/error.h" added manually.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-10-armbru@redhat.com>
[Conflicts in hw/misc/empty_slot.c and hw/sparc/leon3.c resolved]
The NRF51 series SoC have 3 timer peripherals, each having
4 counters. To help differentiate which peripheral is accessed,
display the timer ID in the trace events.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200504072822.18799-4-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Move RTC devices under the hw/rtc/ subdirectory.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20191003230404.19384-12-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The M48T59 is a Real Time Clock, not a timer.
Move it under the hw/rtc/ subdirectory.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20191003230404.19384-5-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The MC146818 is a Real Time Clock, not a timer.
Move it under the hw/rtc/ subdirectory.
Use copyright statement from 80cabfad16 for "hw/rtc/mc146818rtc.h".
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20191003230404.19384-4-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The PL031 is a Real Time Clock, not a timer.
Move it under the hw/rtc/ subdirectory.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20191003230404.19384-3-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The AST2600 timer replaces control register 2 with a interrupt status
register. It is set by hardware when an IRQ occurs and cleared by
software.
Modify the vmstate version to take into account the new fields.
Based on previous work from Joel Stanley.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190925143248.10000-8-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The AST2600 timer has a third control register that is used to
implement a set-to-clear feature for the main control register.
On the AST2600, it is not configurable via 0x38 (control register 3)
as it is on the AST2500.
Based on previous work from Joel Stanley.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190925143248.10000-7-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The AST2500 timer has a third control register that is used to
implement a set-to-clear feature for the main control register.
This models the behaviour expected by the AST2500 while maintaining
the same behaviour for the AST2400.
The vmstate version is not increased yet because the structure is
modified again in the following patches.
Based on previous work from Joel Stanley.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190925143248.10000-6-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The most important changes will be on the register range 0x34 - 0x3C
memops. Introduce class read/write operations to handle the
differences between SoCs.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190925143248.10000-5-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Switch the mss-timer code away from bottom-half based ptimers to
the new transaction-based ptimer API. This just requires adding
begin/commit calls around the various places that modify the ptimer
state, and using the new ptimer_init() function to create the timer.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191008171740.9679-20-peter.maydell@linaro.org
In my "build everything" tree, changing sysemu/sysemu.h triggers a
recompile of some 5400 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
Almost a third of its inclusions are actually superfluous. Delete
them. Downgrade two more to qapi/qapi-types-run-state.h, and move one
from char/serial.h to char/serial.c.
hw/semihosting/config.c, monitor/monitor.c, qdev-monitor.c, and
stubs/semihost.c define variables declared in sysemu/sysemu.h without
including it. The compiler is cool with that, but include it anyway.
This doesn't reduce actual use much, as it's still included into
widely included headers. The next commit will tackle that.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-27-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
In my "build everything" tree, changing hw/qdev-properties.h triggers
a recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
Many places including hw/qdev-properties.h (directly or via hw/qdev.h)
actually need only hw/qdev-core.h. Include hw/qdev-core.h there
instead.
hw/qdev.h is actually pointless: all it does is include hw/qdev-core.h
and hw/qdev-properties.h, which in turn includes hw/qdev-core.h.
Replace the remaining uses of hw/qdev.h by hw/qdev-properties.h.
While there, delete a few superfluous inclusions of hw/qdev-core.h.
Touching hw/qdev-properties.h now recompiles some 1200 objects.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Daniel P. Berrangé" <berrange@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190812052359.30071-22-armbru@redhat.com>
In my "build everything" tree, changing hw/hw.h triggers a recompile
of some 2600 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
The previous commits have left only the declaration of hw_error() in
hw/hw.h. This permits dropping most of its inclusions. Touching it
now recompiles less than 200 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-19-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing hw/irq.h triggers a recompile
of some 5400 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get qemu_irq and.or qemu_irq_handler.
Move the qemu_irq and qemu_irq_handler typedefs from hw/irq.h to
qemu/typedefs.h, and then include hw/irq.h only where it's still
needed. Touching it now recompiles only some 500 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-13-armbru@redhat.com>
Back in 2016, we discussed[1] rules for headers, and these were
generally liked:
1. Have a carefully curated header that's included everywhere first. We
got that already thanks to Peter: osdep.h.
2. Headers should normally include everything they need beyond osdep.h.
If exceptions are needed for some reason, they must be documented in
the header. If all that's needed from a header is typedefs, put
those into qemu/typedefs.h instead of including the header.
3. Cyclic inclusion is forbidden.
This patch gets include/ closer to obeying 2.
It's actually extracted from my "[RFC] Baby steps towards saner
headers" series[2], which demonstrates a possible path towards
checking 2 automatically. It passes the RFC test there.
[1] Message-ID: <87h9g8j57d.fsf@blackfin.pond.sub.org>
https://lists.nongnu.org/archive/html/qemu-devel/2016-03/msg03345.html
[2] Message-Id: <20190711122827.18970-1-armbru@redhat.com>
https://lists.nongnu.org/archive/html/qemu-devel/2019-07/msg02715.html
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-2-armbru@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
The PL031 RTC tracks the difference between the guest RTC
and the host RTC using a tick_offset field. For migration,
however, we currently always migrate the offset between
the guest and the vm_clock, even if the RTC clock is not
the same as the vm_clock; this was an attempt to retain
migration backwards compatibility.
Unfortunately this results in the RTC behaving oddly across
a VM state save and restore -- since the VM clock stands still
across save-then-restore, regardless of how much real world
time has elapsed, the guest RTC ends up out of sync with the
host RTC in the restored VM.
Fix this by migrating the raw tick_offset. To retain migration
compatibility as far as possible, we have a new property
migrate-tick-offset; by default this is 'true' and we will
migrate the true tick offset in a new subsection; if the
incoming data has no subsection we fall back to the old
vm_clock-based offset information, so old->new migration
compatibility is preserved. For complete new->old migration
compatibility, the property is set to 'false' for 4.0 and
earlier machine types (this will only affect 'virt-4.0'
and below, as none of the other pl031-using machines are
versioned).
Reported-by: Russell King <rmk@armlinux.org.uk>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-id: 20190709143912.28905-1-peter.maydell@linaro.org
The RTC is modeled to provide time and date functionality. It is
initialised at zero to match the hardware.
There is no modelling of the alarm functionality, which includes the IRQ
line. As there is no guest code to exercise this function that is
acceptable for now.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20190618165311.27066-4-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
No header includes qemu-common.h after this commit, as prescribed by
qemu-common.h's file comment.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190523143508.25387-5-armbru@redhat.com>
[Rebased with conflicts resolved automatically, except for
include/hw/arm/xlnx-zynqmp.h hw/arm/nrf51_soc.c hw/arm/msf2-soc.c
block/qcow2-refcount.c block/qcow2-cluster.c block/qcow2-cache.c
target/arm/cpu.h target/lm32/cpu.h target/m68k/cpu.h target/mips/cpu.h
target/moxie/cpu.h target/nios2/cpu.h target/openrisc/cpu.h
target/riscv/cpu.h target/tilegx/cpu.h target/tricore/cpu.h
target/unicore32/cpu.h target/xtensa/cpu.h; bsd-user/main.c and
net/tap-bsd.c fixed up]
The system_clock_scale global is used only by the armv7m systick
device; move the extern declaration to the armv7m_systick.h header,
and expand the comment to explain what it is and that it should
ideally be replaced with a different approach.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190516163857.6430-2-peter.maydell@linaro.org
Leading underscores are ill-advised because such identifiers are
reserved. Trailing underscores are merely ugly. Strip both.
Our header guards commonly end in _H. Normalize the exceptions.
Done with scripts/clean-header-guards.pl.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190315145123.28030-7-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[Changes to slirp/ dropped, as we're about to spin it off]
Create a new include file for the pl031's device struct,
type macros, etc, so that it can be instantiated using
the "embedded struct" coding style.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
This patch adds the model for the nRF51 timer peripheral.
Currently, only the TIMER mode is implemented.
Signed-off-by: Steffen Görtz <contrib@steffen-goertz.de>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190103091119.9367-9-stefanha@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In file included from /home/thuth/devel/qemu/hw/timer/aspeed_timer.c:16:
/home/thuth/devel/qemu/include/hw/misc/aspeed_scu.h:37:3: error:
redefinition of typedef 'AspeedSCUState' is a C11 feature
[-Werror,-Wtypedef-redefinition]
} AspeedSCUState;
^
/home/thuth/devel/qemu/include/hw/timer/aspeed_timer.h:27:31: note:
previous definition is here
typedef struct AspeedSCUState AspeedSCUState;
Reported-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180921161939.822-2-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Arm Cortex-M System Design Kit includes a "dual-input timer module"
which combines two programmable down-counters. Implement a model
of this device.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180820141116.9118-4-peter.maydell@linaro.org
The timer controller can be driven by either an external 1MHz clock or
by the APB clock. Today, the model makes the assumption that the APB
frequency is always set to 24MHz but this is incorrect.
The AST2400 SoC on the palmetto machines uses a 48MHz input clock
source and the APB can be set to 48MHz. The consequence is a general
system slowdown. The QEMU machines using the AST2500 SoC do not seem
impacted today because the APB frequency is still set to 24MHz.
We fix the timer frequency for all SoCs by linking the Timer model to
the SCU model. The APB frequency driving the timers is now the one
configured for the SoC.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 20180622075700.5923-4-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Peter Maydell
Hao Wu
Philippe Mathieu-Daudé
Eduardo Habkost
Havard Skinnemoen
Michael Rolnik
Yoshinori Sato
Markus Armbruster
Philippe Mathieu-Daudé
Cédric Le Goater
Joel Stanley
Steffen Görtz
Marc-André Lureau