UART5 is typically used as the default debug UART on the AST2600, but
UART1 is also designed to be a debug UART. All the AST2600 UART's have
semi-configurable clock rates through registers in the System Control
Unit (SCU), but only UART5 works out of the box with zero-initialized
values. The rest of the UART's expect a few of the registers to be
initialized to non-zero values, or else the clock rate calculation will
yield zero or undefined (due to a divide-by-zero).
For reference, the U-Boot clock rate driver here shows the calculation:
https://github.com/facebook/openbmc-uboot/blob/15f7e0dc01d8/drivers/clk/aspeed/clk_ast2600.c#L357
To summarize, UART5 allows selection from 4 rates: 24 MHz, 192 MHz, 24 /
13 MHz, and 192 / 13 MHz. The other UART's allow selecting either the
"low" rate (UARTCLK) or the "high" rate (HUARTCLK). UARTCLK and HUARTCLK
are configurable themselves:
UARTCLK = UXCLK * R / (N * 2)
HUARTCLK = HUXCLK * HR / (HN * 2)
UXCLK and HUXCLK are also configurable, and depend on the APLL and/or
HPLL clock rates, which also derive from complicated calculations. Long
story short, there's lots of multiplication and division from
configurable registers, and most of these registers are zero-initialized
in QEMU, which at best is unexpected and at worst causes this clock rate
driver to hang from divide-by-zero's. This can also be difficult to
diagnose, because it may cause U-Boot to hang before serial console
initialization completes, requiring intervention from gdb.
This change just initializes all of these registers with default values
from the datasheet.
To test this, I used Facebook's AST2600 OpenBMC image for "fuji", with
the following diff applied (because fuji uses UART1 for console output,
not UART5).
@@ -323,8 +323,8 @@ static void aspeed_soc_ast2600_realize(DeviceState *dev, Error **errp)
}
/* UART - attach an 8250 to the IO space as our UART5 */
- serial_mm_init(get_system_memory(), sc->memmap[ASPEED_DEV_UART5], 2,
- aspeed_soc_get_irq(s, ASPEED_DEV_UART5),
+ serial_mm_init(get_system_memory(), sc->memmap[ASPEED_DEV_UART1], 2,
+ aspeed_soc_get_irq(s, ASPEED_DEV_UART1),
38400, serial_hd(0), DEVICE_LITTLE_ENDIAN);
/* I2C */
Without these clock rate registers being initialized, U-Boot hangs in
the clock rate driver from a divide-by-zero, because the UART1 clock
rate register reads return zero, and there's no console output. After
initializing them with default values, fuji boots successfully.
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
[ clg: Removed _PARAM suffix ]
Message-Id: <20210906134023.3711031-2-pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Witherspoon uses the DPS310 as a temperature sensor. Rainier uses it as
a temperature and humidity sensor.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210629142336.750058-5-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This contains some hardcoded register values that were obtained from the
hardware after reading the temperature.
It does enough to test the Linux kernel driver. The FIFO mode, IRQs and
operation modes other than the default as used by Linux are not modelled.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Message-Id: <20210616073358.750472-2-joel@jms.id.au>
[ clg: - Fixed sequential reading
- Reworked regs_reset_state array
- Moved model under hw/sensor/ ]
Message-Id: <20210629142336.750058-4-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This is the latest revision of the ASPEED 2600 SoC. As there is no
need to model multiple revisions of the same SoC for the moment,
update the SCU AST2600 to model the A3 revision instead of the A1 and
adapt the AST2600 SoC and machines.
Reset values are taken from v8 of the datasheet.
Signed-off-by: Joel Stanley <joel@jms.id.au>
[ clg: - Introduced an Aspeed "ast2600-a3" SoC class
- Commit log update ]
Message-Id: <20210629142336.750058-3-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
These are the devices documented by the Rainier device tree. With this
we can see the guest discovering the multiplexers and probing the eeprom
devices:
i2c i2c-2: Added multiplexed i2c bus 16
i2c i2c-2: Added multiplexed i2c bus 17
i2c i2c-2: Added multiplexed i2c bus 18
i2c i2c-2: Added multiplexed i2c bus 19
i2c-mux-gpio i2cmux: 4 port mux on 1e78a180.i2c-bus adapter
at24 20-0050: 8192 byte 24c64 EEPROM, writable, 1 bytes/write
i2c i2c-4: Added multiplexed i2c bus 20
at24 21-0051: 8192 byte 24c64 EEPROM, writable, 1 bytes/write
i2c i2c-4: Added multiplexed i2c bus 21
at24 22-0052: 8192 byte 24c64 EEPROM, writable, 1 bytes/write
Signed-off-by: Joel Stanley <joel@jms.id.au>
[ clg: Introduced aspeed_eeprom_init ]
Message-Id: <20210629142336.750058-2-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
There was a bit of a thinko in the state calculation where every odd pin
in was reported in e.g. "pwm0" mode rather than "off". This was the
result of an incorrect bit shift for the 2-bit field representing each
LED state.
Fixes: a90d8f8467 ("misc/pca9552: Add qom set and get")
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210723043624.348158-1-andrew@aj.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
There are two GPIO controllers in the ast2600; one is 3.3V and the other
is 1.8V.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Rashmica Gupta <rashmica.g@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210713065854.134634-4-joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
There's no need to define the registers relative to the 0x800 offset
where the controller is mapped, as the device is instantiated as it's
own model at the correct memory address.
Simplify the defines and remove the offset to save future confusion.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Rashmica Gupta <rashmica.g@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210713065854.134634-3-joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The logic in the handling for the control register required toggling the
enable state for writes to stick. Rework the condition chain to allow
sequential writes that do not update the enable state.
Fixes: 854123bf8d ("wdt: Add Aspeed watchdog device model")
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210709053107.1829304-3-andrew@aj.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
While some of the critical fields remain the same, there is variation in
the definition of the control register across the SoC generations.
Reserved regions are adjusted, while in other cases the mutability or
behaviour of fields change.
Introduce a callback to sanitize the value on writes to ensure model
behaviour reflects the hardware.
Fixes: 854123bf8d ("wdt: Add Aspeed watchdog device model")
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210709053107.1829304-2-andrew@aj.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
According to its dts file in the Linux kernel, we need mac0 and mac1 enabled
instead of mac1 and mac2. Also, g220a is based on aspeed-g5 (ast2500) which
doesn't even have the third interface.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210810035742.550391-1-linux@roeck-us.net>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Commit 7582591ae7 ("aspeed: Support AST2600A1 silicon revision") switched
the silicon revision for AST2600 to revision A1. On revision A1, the first
Ethernet interface is operational. Enable it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210808200457.889955-1-linux@roeck-us.net>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
In do_setsockopt(), the code path for the options which take a struct
ip_mreq_source (IP_BLOCK_SOURCE, IP_UNBLOCK_SOURCE,
IP_ADD_SOURCE_MEMBERSHIP and IP_DROP_SOURCE_MEMBERSHIP) fails to
check the return value from lock_user(). Handle this in the usual
way by returning -TARGET_EFAULT.
(In practice this was probably harmless because we'd pass a NULL
pointer to setsockopt() and the kernel would then return EFAULT.)
Fixes: Coverity CID 1459987
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210809155424.30968-1-peter.maydell@linaro.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The sparc_cpu_dump_state() function is only called within
the same file. Make it static.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20210916084002.1918445-1-f4bug@amsat.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
../target/avr/translate.c: In function ‘gen_jmp_ez’:
../target/avr/translate.c:1012:22: error: implicit conversion from ‘enum <anonymous>’ to ‘DisasJumpType’ [-Werror=enum-conversion]
1012 | ctx->base.is_jmp = DISAS_LOOKUP;
| ^
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Michael Rolnik <mrolnik@gmail.com>
Message-Id: <20210706180936.249912-1-sw@weilnetz.de>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Although we have long supported 'qemu-img convert -o
backing_file=foo,backing_fmt=bar', the fact that we have a shortcut -B
for backing_file but none for backing_fmt has made it more likely that
users accidentally run into:
qemu-img: warning: Deprecated use of backing file without explicit backing format
when using -B instead of -o. For similarity with other qemu-img
commands, such as create and compare, add '-F $fmt' as the shorthand
for '-o backing_fmt=$fmt'. Update iotest 122 for coverage of both
spellings.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20210913131735.1948339-1-eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
Split checking for reserved bits out of aligned offset check.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Tested-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20210914122454.141075-11-vsementsov@virtuozzo.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
- use g_autofree for l1_table
- better name for size in bytes variable
- reduce code blocks nesting
- whitespaces, braces, newlines
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20210914122454.141075-9-vsementsov@virtuozzo.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
Check subcluster bitmap of the l2 entry for different types of
clusters:
- for compressed it must be zero
- for allocated check consistency of two parts of the bitmap
- for unallocated all subclusters should be unallocated
(or zero-plain)
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Tested-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Message-Id: <20210914122454.141075-7-vsementsov@virtuozzo.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
We'll reuse the function to fix wrong L2 entry bitmap. Support it now.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20210914122454.141075-6-vsementsov@virtuozzo.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
Split fix_l2_entry_by_zero() out of check_refcounts_l2() to be
reused in further patch.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20210914122454.141075-5-vsementsov@virtuozzo.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
Add helper to parse compressed l2_entry and use it everywhere instead
of open-coding.
Note, that in most places we move to precise coffset/csize instead of
sector-aligned. Still it should work good enough for updating
refcounts.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20210914122454.141075-4-vsementsov@virtuozzo.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
Let's pass the whole L2 entry and not bother with
L2E_COMPRESSED_OFFSET_SIZE_MASK.
It also helps further refactoring that adds generic
qcow2_parse_compressed_l2_entry() helper.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20210914122454.141075-3-vsementsov@virtuozzo.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
- don't use same name for size in bytes and in entries
- use g_autofree for l2_table
- add whitespace
- fix block comment style
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20210914122454.141075-2-vsementsov@virtuozzo.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
If a gitlab CI job is marked as manual-only but is not marked
as allow_failure, then gitlab considers that the pipeline is
"blocked" until the job has been manually triggered. We need
to mark these manual-only jobs as also allow_failure: true
so that gitlab doesn't insist that they have run before it
will consider the pipeline to be complete.
Fixes: 4c9af1ea14
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-id: 20210915123412.8232-1-peter.maydell@linaro.org
Acked-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Willian Rampazzo <willianr@redhat.com>
We cannot write to images opened with O_DIRECT unless we allow them to
be resized so they are aligned to the sector size: Since 9c60a5d197,
bdrv_node_refresh_perm() ensures that for nodes whose length is not
aligned to the request alignment and where someone has taken a WRITE
permission, the RESIZE permission is taken, too).
Let qemu-img convert pass the BDRV_O_RESIZE flag (which causes
blk_new_open() to take the RESIZE permission) when using cache=none for
the target, so that when writing to it, it can be aligned to the target
sector size.
Without this patch, an error is returned:
$ qemu-img convert -f raw -O raw -t none foo.img /mnt/tmp/foo.img
qemu-img: Could not open '/mnt/tmp/foo.img': Cannot get 'write'
permission without 'resize': Image size is not a multiple of request
alignment
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=1994266
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20210819101200.64235-1-hreitz@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
There is no conflict and no dependency if we have parallel writes to
different subclusters of one cluster when the cluster itself is already
allocated. So, relax extra dependency.
Measure performance:
First, prepare build/qemu-img-old and build/qemu-img-new images.
cd scripts/simplebench
./img_bench_templater.py
Paste the following to stdin of running script:
qemu_img=../../build/qemu-img-{old|new}
$qemu_img create -f qcow2 -o extended_l2=on /ssd/x.qcow2 1G
$qemu_img bench -c 100000 -d 8 [-s 2K|-s 2K -o 512|-s $((1024*2+512))] \
-w -t none -n /ssd/x.qcow2
The result:
All results are in seconds
------------------ --------- ---------
old new
-s 2K 6.7 ± 15% 6.2 ± 12%
-7%
-s 2K -o 512 13 ± 3% 11 ± 5%
-16%
-s $((1024*2+512)) 9.5 ± 4% 8.4
-12%
------------------ --------- ---------
So small writes are more independent now and that helps to keep deeper
io queue which improves performance.
271 iotest output becomes racy for three allocation in one cluster.
Second and third writes may finish in different order. Second and
third requests don't depend on each other any more. Still they both
depend on first request anyway. Filter out second and third write
offsets to cover both possible outputs.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20210824101517.59802-4-vsementsov@virtuozzo.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
[hreitz: s/ an / and /]
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
No logic change, just prepare for the following commit. While being
here do also small grammar fix in a comment.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20210824101517.59802-3-vsementsov@virtuozzo.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
Add simple grammar-parsing template benchmark. New tool consume test
template written in bash with some special grammar injections and
produces multiple tests, run them and finally print a performance
comparison table of different tests produced from one template.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20210824101517.59802-2-vsementsov@virtuozzo.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
We must not inactivate child when parent has write permissions on
it.
Calling .bdrv_inactivate() doesn't help: actually only qcow2 has this
handler and it is used to flush caches, not for permission
manipulations.
So, let's simply check cumulative parent permissions before
inactivating the node.
This commit fixes a crash when we do migration during backup: prior to
the commit nothing prevents all nodes inactivation at migration finish
and following backup write to the target crashes on assertion
"assert(!(bs->open_flags & BDRV_O_INACTIVE));" in
bdrv_co_write_req_prepare().
After the commit, we rely on the fact that copy-before-write filter
keeps write permission on target node to be able to write to it. So
inactivation fails and migration fails as expected.
Corresponding test now passes, so, enable it.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20210911120027.8063-3-vsementsov@virtuozzo.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
Add a simple test which tries to run migration during backup.
bdrv_inactivate_all() should fail. But due to bug (see next commit with
fix) it doesn't, nodes are inactivated and continued backup crashes
on assertion "assert(!(bs->open_flags & BDRV_O_INACTIVE));" in
bdrv_co_write_req_prepare().
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20210911120027.8063-2-vsementsov@virtuozzo.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
In mirror_iteration() we call mirror_wait_on_conflicts() with
`self` parameter set to NULL.
Starting from commit d44dae1a7c we dereference `self` pointer in
mirror_wait_on_conflicts() without checks if it is not NULL.
Backtrace:
Program terminated with signal SIGSEGV, Segmentation fault.
#0 mirror_wait_on_conflicts (self=0x0, s=<optimized out>, offset=<optimized out>, bytes=<optimized out>)
at ../block/mirror.c:172
172 self->waiting_for_op = op;
[Current thread is 1 (Thread 0x7f0908931ec0 (LWP 380249))]
(gdb) bt
#0 mirror_wait_on_conflicts (self=0x0, s=<optimized out>, offset=<optimized out>, bytes=<optimized out>)
at ../block/mirror.c:172
#1 0x00005610c5d9d631 in mirror_run (job=0x5610c76a2c00, errp=<optimized out>) at ../block/mirror.c:491
#2 0x00005610c5d58726 in job_co_entry (opaque=0x5610c76a2c00) at ../job.c:917
#3 0x00005610c5f046c6 in coroutine_trampoline (i0=<optimized out>, i1=<optimized out>)
at ../util/coroutine-ucontext.c:173
#4 0x00007f0909975820 in ?? () at ../sysdeps/unix/sysv/linux/x86_64/__start_context.S:91
from /usr/lib64/libc.so.6
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=2001404
Fixes: d44dae1a7c ("block/mirror: fix active mirror dead-lock in mirror_wait_on_conflicts")
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-Id: <20210910124533.288318-1-sgarzare@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
297 so far does not check the named tests, which reside in the tests/
directory (i.e. full path tests/qemu-iotests/tests). Fix it.
Thanks to the previous two commits, all named tests pass its scrutiny,
so we do not have to add anything to SKIP_FILES.
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
Reviewed-by: Willian Rampazzo <willianr@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20210902094017.32902-6-hreitz@redhat.com>
The AbnormalShutdown exception class is not in qemu.machine, but in
qemu.machine.machine. (qemu.machine.AbnormalShutdown was enough for
Python to find it in order to run this test, but pylint complains about
it.)
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20210902094017.32902-5-hreitz@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
There are a couple of things pylint takes issue with:
- The "time" import is unused
- The import order (iotests should come last)
- get_bitmap_hash() doesn't use @self and so should be a function
- Semicolons at the end of some lines
- Parentheses after "if"
- Some lines are too long (80 characters instead of 79)
- inject_test_case()'s @name parameter shadows a top-level @name
variable
- "lambda self: mc(self)" were equivalent to just "mc", but in
inject_test_case(), it is not equivalent, so add a comment and disable
the warning locally
- Always put two empty lines after a function
- f'exec: cat > /dev/null' does not need to be an f-string
Fix them.
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20210902094017.32902-4-hreitz@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
pylint complains that discards1_sha256 and all_discards_sha256 are first
set in non-__init__ methods.
These variables are not really class-variables anyway, so let them
instead be returned by start_postcopy(), thus silencing pylint.
Suggested-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20210902094017.32902-3-hreitz@redhat.com>
169 and 199 have been renamed and moved to tests/ (commit a44be0334b:
"iotests: rename and move 169 and 199 tests"), so we can drop them from
the skip list.
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
Reviewed-by: Willian Rampazzo <willianr@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20210902094017.32902-2-hreitz@redhat.com>
pylint proposes using `[]` instead of `list()` and `{}` instead of
`dict()`, because it is faster. That seems simple enough, so heed its
advice.
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20210824153540.177128-3-hreitz@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
As of recently, pylint complains when `open()` calls are missing an
`encoding=` specified. Everything we have should be UTF-8 (and in fact,
everything should be UTF-8, period (exceptions apply)), so use that.
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20210824153540.177128-2-hreitz@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
bdrv_co_block_status() does it for us, we do not need to do it here.
The advantage of not capping *pnum is that bdrv_co_block_status() can
cache larger data regions than requested by its caller.
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20210812084148.14458-7-hreitz@redhat.com>
bdrv_co_block_status() does it for us, we do not need to do it here.
The advantage of not capping *pnum is that bdrv_co_block_status() can
cache larger data regions than requested by its caller.
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20210812084148.14458-6-hreitz@redhat.com>
