This is to enable them to be used outside of dp8393x.c.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
CC: Jason Wang <jasowang@redhat.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230621085353.113233-15-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Commit 3fe9a838ec "dp8393x: Always use 32-bit accesses" set .impl.min_access_size
and .impl.max_access_size to 4 to try and fix the Linux jazzsonic driver which uses
32-bit accesses.
The problem with forcing the register access to 32-bit in this way is that since the
dp8393x uses 16-bit registers, a manual endian swap is required for devices on big
endian machines with 32-bit accesses.
For both access sizes and machine endians the QEMU memory API can do the right thing
automatically: all that is needed is to set .impl.min_access_size to 2 to declare that
the dp8393x implements 16-bit registers.
Normally .impl.max_access_size should also be set to 2, however that doesn't quite
work in this case since the register stride is specified using a (dynamic) it_shift
property which is applied during the MMIO access itself. The effect of this is that
for a 32-bit access the memory API performs 2 x 16-bit accesses, but the use of
it_shift within the MMIO access itself causes the register value to be repeated in both
the top 16-bits and bottom 16-bits. The Linux jazzsonic driver expects the stride to be
zero-extended up to access size and therefore fails to correctly detect the dp8393x
device due to the extra data in the top 16-bits.
The solution here is to remove .impl.max_access_size so that the memory API will
correctly zero-extend the 16-bit registers to the access size up to and including
it_shift. Since it_shift is never greater than 2 than this will always do the right
thing for both 16-bit and 32-bit accesses regardless of the machine endian, allowing
the manual endian swap code to be removed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Fixes: 3fe9a838ec ("dp8393x: Always use 32-bit accesses")
Message-Id: <20210705214929.17222-2-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Finn Thain <fthain@linux-m68k.org>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Instead of accessing N registers via a single address_space API
call using a temporary buffer (stored in the device state) and
updating each register, move the address_space call in the
register put/get. The load/store and word size checks are moved
to put/get too. This simplifies a bit, making the code easier
to read.
Co-developed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Co-developed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Finn Thain <fthain@linux-m68k.org>
Message-Id: <20210710174954.2577195-8-f4bug@amsat.org>
Per the DP83932C datasheet from July 1995:
4.0 SONIC Registers
4.1 THE CAM UNIT
The Content Addressable Memory (CAM) consists of sixteen
48-bit entries for complete address filtering of network
packets. Each entry corresponds to a 48-bit destination
address that is user programmable and can contain any
combination of Multicast or Physical addresses. Each entry
is partitioned into three 16-bit CAM cells accessible
through CAM Address Ports (CAP 2, CAP 1 and CAP 0) with
CAP0 corresponding to the least significant 16 bits of
the Destination Address and CAP2 corresponding to the
most significant bits.
Store the CAM registers as 16-bit as it simplifies the code.
Having now the CAM registers as arrays of 3 uint16_t, we can avoid
using the VMSTATE_BUFFER_UNSAFE macro by using VMSTATE_UINT16_2DARRAY
which is more appropriate. This breaks the migration stream however.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Finn Thain <fthain@linux-m68k.org>
Message-Id: <20210710174954.2577195-5-f4bug@amsat.org>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Finn Thain <fthain@linux-m68k.org>
Message-Id: <20210710174954.2577195-3-f4bug@amsat.org>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Replace address_space_rw(is_write=1) by address_space_write()
and remove pointless cast.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Finn Thain <fthain@linux-m68k.org>
Message-Id: <20210710174954.2577195-2-f4bug@amsat.org>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Currently when a LOAD CAM command is executed the entries are loaded into the
CAM from memory in order which is incorrect. According to the datasheet the
first entry in the CAM descriptor is the entry index which means that each
descriptor may update any single entry in the CAM rather than the Nth entry.
Decode the CAM entry index and use it store the descriptor in the appropriate
slot in the CAM. This fixes the issue where the MacOS toolbox loads a single
CAM descriptor into the final slot in order to perform a loopback test which
must succeed before the Ethernet port is enabled.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Finn Thain <fthain@linux-m68k.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210625065401.30170-10-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
According to the datasheet the dp8393x chipset does not contain any NVRAM capable
of storing a MAC address or checksum. Now that both the MIPS jazz and m68k q800
boards generate the PROM region and checksum themselves, remove the generated
PROM from the dp8393x device itself.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Finn Thain <fthain@linux-m68k.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210625065401.30170-6-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Finn Thain <fthain@linux-m68k.org>
Message-Id: <20210625065401.30170-3-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Also fix a simple comment typo of "constrainst" to "constraints".
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Finn Thain <fthain@linux-m68k.org>
Message-Id: <20210625065401.30170-2-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This patch switches to use qemu_receive_packet() which can detect
reentrancy and return early.
This is intended to address CVE-2021-3416.
Cc: Prasad J Pandit <ppandit@redhat.com>
Cc: qemu-stable@nongnu.org
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com
Signed-off-by: Jason Wang <jasowang@redhat.com>
An integer underflow could occur during packet transmission due to 'tx_len' not
being updated if SONIC_TFC register is set to zero. Check for negative 'tx_len'
when removing existing FCS.
RHBZ: https://bugzilla.redhat.com/show_bug.cgi?id=1899722
Signed-off-by: Mauro Matteo Cascella <mcascell@redhat.com>
Reported-by: Gaoning Pan <pgn@zju.edu.cn>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-id: 20201124092445.658647-1-mcascell@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some typedefs and macros are defined after the type check macros.
This makes it difficult to automatically replace their
definitions with OBJECT_DECLARE_TYPE.
Patch generated using:
$ ./scripts/codeconverter/converter.py -i \
--pattern=QOMStructTypedefSplit $(git grep -l '' -- '*.[ch]')
which will split "typdef struct { ... } TypedefName"
declarations.
Followed by:
$ ./scripts/codeconverter/converter.py -i --pattern=MoveSymbols \
$(git grep -l '' -- '*.[ch]')
which will:
- move the typedefs and #defines above the type check macros
- add missing #include "qom/object.h" lines if necessary
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-9-ehabkost@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-10-ehabkost@redhat.com>
Message-Id: <20200831210740.126168-11-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The NetCanReceive handler return whether the device can or
can not receive new packets. Make it obvious by returning
a boolean type.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This commit was produced with the Coccinelle script
scripts/coccinelle/memory-region-housekeeping.cocci.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
A portion of a recent patch got lost due to a merge snafu. That patch is
now commit 88f632fbb1 ("dp8393x: Mask EOL bit from descriptor addresses").
This patch restores the portion that got lost.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <alpine.LNX.2.22.394.2003041421280.12@nippy.intranet>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Section 3.4.7 of the datasheet explains that,
The RBE bit in the Interrupt Status register is set when the
SONIC finishes using the second to last receive buffer and reads
the last RRA descriptor. Actually, the SONIC is not truly out of
resources, but gives the system an early warning of an impending
out of resources condition.
RBE does not mean actual receive buffer exhaustion, and reception should
not be stopped. This is important because Linux will not check and clear
the RBE interrupt until it receives another packet. But that won't
happen if can_receive returns false. This bug causes the SONIC to become
deaf (until reset).
Fix this with a new flag to indicate actual receive buffer exhaustion.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The jazzsonic driver in Linux uses the Silicon Revision register value
to probe the chip. The driver fails unless the SR register contains 4.
Unfortunately, reading this register in QEMU usually returns 0 because
the s->regs[] array gets wiped after a software reset.
Fixes: bd8f1ebce4 ("net/dp8393x: fix hardware reset")
Suggested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Jason Wang <jasowang@redhat.com>
These operations need to take place regardless of whether or not
rx descriptors have been used up (that is, EOL flag was observed).
The algorithm is now the same for a packet that was withheld as for
a packet that was not.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Jason Wang <jasowang@redhat.com>
When the SONIC receives a packet into the last available descriptor, it
retains ownership of that descriptor for as long as necessary.
Section 3.4.7 of the datasheet says,
When the system appends more descriptors, the SONIC releases ownership
of the descriptor after writing 0000h to the RXpkt.in_use field.
The packet can now be processed by the host, so raise a PKTRX interrupt,
just like the normal case.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The existing code has a bug where the Remaining Buffer Word Count (RBWC)
is calculated with a truncating division, which gives the wrong result
for odd-sized packets.
Section 1.4.1 of the datasheet says,
Once the end of the packet has been reached, the serializer will
fill out the last word (16-bit mode) or long word (32-bit mode)
if the last byte did not end on a word or long word boundary
respectively. The fill byte will be 0FFh.
Implement buffer padding so that buffer limits are correctly enforced.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Section 3.4.1 of the datasheet says,
The alignment of the RRA is confined to either word or long word
boundaries, depending upon the data width mode. In 16-bit mode,
the RRA must be aligned to a word boundary (A0 is always zero)
and in 32-bit mode, the RRA is aligned to a long word boundary
(A0 and A1 are always zero).
This constraint has been implemented for 16-bit mode; implement it
for 32-bit mode too.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
A received packet consumes pkt_size bytes in the buffer and the frame
checksum that's appended to it consumes another 4 bytes. The Receive
Buffer Address register takes the former quantity into account but
not the latter. So the next packet written to the buffer overwrites
the frame checksum. Fix this.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Add a bounds check to prevent a large packet from causing a buffer
overflow. This is defensive programming -- I haven't actually tried
sending an oversized packet or a jumbo ethernet frame.
The SONIC handles packets that are too big for the buffer by raising
the RBAE interrupt and dropping them. Linux uses that interrupt to
count dropped packets.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Jason Wang <jasowang@redhat.com>
It doesn't make sense to clear the command register bit unless the
command was actually issued.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Follow the algorithm given in the National Semiconductor DP83932C
datasheet in section 3.4.7:
At the next reception, the SONIC re-reads the last RXpkt.link field,
and updates its CRDA register to point to the next descriptor.
The chip is designed to allow the host to provide a new list of
descriptors in this way.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This function re-uses its 'size' argument as a scratch variable.
Instead, declare a local 'size' variable for that purpose so that the
function result doesn't get messed up.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Jason Wang <jasowang@redhat.com>
According to the datasheet, section 3.4.4, "in 32-bit mode ... the SONIC
always writes long words".
Therefore, use the same technique for the 'in_use' field that is used
everywhere else, and write the full long word.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The DP83932 and DP83934 have 32 data lines. The datasheet says,
Data Bus: These bidirectional lines are used to transfer data on the
system bus. When the SONIC is a bus master, 16-bit data is transferred
on D15-D0 and 32-bit data is transferred on D31-D0. When the SONIC is
accessed as a slave, register data is driven onto lines D15-D0.
D31-D16 are held TRI-STATE if SONIC is in 16-bit mode. If SONIC is in
32-bit mode, they are driven, but invalid.
Always use 32-bit accesses both as bus master and bus slave.
Force the MSW to zero in bus master mode.
This gets the Linux 'jazzsonic' driver working, and avoids the need for
prior hacks to make the NetBSD 'sn' driver work.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The Least Significant bit of a descriptor address register is used as
an EOL flag. It has to be masked when the register value is to be used
as an actual address for copying memory around. But when the registers
are to be updated the EOL bit should not be masked.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The address_space_rw() function allows either reads or writes
depending on the is_write argument passed to it; this is useful
when the direction of the access is determined programmatically
(as for instance when handling the KVM_EXIT_MMIO exit reason).
Under the hood it just calls either address_space_write() or
address_space_read_full().
We also use it a lot with a constant is_write argument, though,
which has two issues:
* when reading "address_space_rw(..., 1)" this is less
immediately clear to the reader as being a write than
"address_space_write(...)"
* calling address_space_rw() bypasses the optimization
in address_space_read() that fast-paths reads of a
fixed length
This commit was produced with the included Coccinelle script
scripts/coccinelle/exec_rw_const.cocci.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20200218112457.22712-1-peter.maydell@linaro.org>
[PMD: Update macvm_set_cr0() reported by Laurent Vivier]
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Since its introduction in commit ac1970fbe8, address_space_rw()
takes a boolean 'is_write' argument. Fix the codebase by using
an explicit boolean type.
This commit was produced with the included Coccinelle script
scripts/coccinelle/exec_rw_const.
Inspired-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
This commit was produced with the included Coccinelle script
scripts/coccinelle/exec_rw_const.
Two lines in hw/net/dp8393x.c that Coccinelle produced that
were over 80 characters were re-wrapped by hand.
Suggested-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
The NetReceive prototype gets a const buffer:
typedef ssize_t (NetReceive)(NetClientState *, const uint8_t *, size_t);
We already have the address_space_write() method to write a const
buffer to an address space. Use it to avoid:
hw/net/i82596.c: In function ‘i82596_receive’:
hw/net/i82596.c:644:54: error: passing argument 4 of ‘address_space_rw’ discards ‘const’ qualifier from pointer target type [-Werror=discarded-qualifiers]
This commit was produced with the included Coccinelle script
scripts/coccinelle/exec_rw_const.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Link property is the correct way to pass a MemoryRegion to a device
for DMA purposes.
Sidenote: as a sysbus device, this remains non-usercreatable
even though we can drop the specific flag here.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Tested-by: Laurent Vivier <laurent@vivier.eu>
RXpkt.in_use is always 16 bit wide, but when the bus access mode is 32bit
and the endianness is big, we must access the second word and not the
first. This patch adjusts the offset according to the size and endianness.
This fixes DHCP for Q800 guest.
Fixes: be92084198 ("dp8393x: manage big endian bus")
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Tested-by: Hervé Poussineau <hpoussin@reactos.org>
Message-Id: <20191106112341.23735-3-laurent@vivier.eu>
Move it from the stack.
It's only 24 bytes, and this simplifies the dp8393x_get()/
dp8393x_put() interface.
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Message-Id: <20191106112341.23735-2-laurent@vivier.eu>
This is needed by Quadra 800, this card can run on little-endian
or big-endian bus.
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Tested-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Message-Id: <20191026164546.30020-5-laurent@vivier.eu>
In my "build everything" tree, changing hw/qdev-properties.h triggers
a recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
Many places including hw/qdev-properties.h (directly or via hw/qdev.h)
actually need only hw/qdev-core.h. Include hw/qdev-core.h there
instead.
hw/qdev.h is actually pointless: all it does is include hw/qdev-core.h
and hw/qdev-properties.h, which in turn includes hw/qdev-core.h.
Replace the remaining uses of hw/qdev.h by hw/qdev-properties.h.
While there, delete a few superfluous inclusions of hw/qdev-core.h.
Touching hw/qdev-properties.h now recompiles some 1200 objects.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Daniel P. Berrangé" <berrange@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190812052359.30071-22-armbru@redhat.com>
In my "build everything" tree, changing migration/vmstate.h triggers a
recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get VMStateDescription. The previous commit made
that unnecessary.
Include migration/vmstate.h only where it's still needed. Touching it
now recompiles only some 1600 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-16-armbru@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing hw/irq.h triggers a recompile
of some 5400 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get qemu_irq and.or qemu_irq_handler.
Move the qemu_irq and qemu_irq_handler typedefs from hw/irq.h to
qemu/typedefs.h, and then include hw/irq.h only where it's still
needed. Touching it now recompiles only some 500 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-13-armbru@redhat.com>
Currently we use memory_region_init_rom_nomigrate() to create
the "dp3893x-prom" memory region, and we don't manually register
it with vmstate_register_ram(). This currently means that its
contents are migrated but as a ram block whose name is the empty
string; in future it may mean they are not migrated at all. Use
memory_region_init_ram() instead.
Note that this is a a cross-version migration compatibility break
for the MIPS "magnum" and "pica61" machines.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Aleksandar Markovic <aleksandar.markovic@wavecomp.com>
Message-id: 20180706174309.27110-1-peter.maydell@linaro.org
Rename memory_region_init_ram() to memory_region_init_ram_nomigrate().
This leaves the way clear for us to provide a memory_region_init_ram()
which does handle migration.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1499438577-7674-4-git-send-email-peter.maydell@linaro.org
cannot_instantiate_with_device_add_yet was introduced by commit
efec3dd631 to replace no_user. It was
supposed to be a temporary measure.
When it was introduced, we had 54
cannot_instantiate_with_device_add_yet=true lines in the code.
Today (3 years later) this number has not shrunk: we now have
57 cannot_instantiate_with_device_add_yet=true lines. I think it
is safe to say it is not a temporary measure, and we won't see
the flag go away soon.
Instead of a long field name that misleads people to believe it
is temporary, replace it a shorter and less misleading field:
user_creatable.
Except for code comments, changes were generated using the
following Coccinelle patch:
@@
expression DC;
@@
(
-DC->cannot_instantiate_with_device_add_yet = false;
+DC->user_creatable = true;
|
-DC->cannot_instantiate_with_device_add_yet = true;
+DC->user_creatable = false;
)
@@
typedef ObjectClass;
expression dc;
identifier class, data;
@@
static void device_class_init(ObjectClass *class, void *data)
{
...
dc->hotpluggable = true;
+dc->user_creatable = true;
...
}
@@
@@
struct DeviceClass {
...
-bool cannot_instantiate_with_device_add_yet;
+bool user_creatable;
...
}
@@
expression DC;
@@
(
-!DC->cannot_instantiate_with_device_add_yet
+DC->user_creatable
|
-DC->cannot_instantiate_with_device_add_yet
+!DC->user_creatable
)
Cc: Alistair Francis <alistair.francis@xilinx.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Cc: Markus Armbruster <armbru@redhat.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Thomas Huth <thuth@redhat.com>
Acked-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Acked-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20170503203604.31462-2-ehabkost@redhat.com>
[ehabkost: kept "TODO remove once we're there" comment]
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
