Implement the SYSRESETREQ bit of the AIRCR register
for armv7-m (ie. cortex-m3) to trigger a GPIO out.
Signed-off-by: Michael Davidsaver <mdavidsaver@gmail.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Change the implementation of the Interrupt Control and State Register
in the v7M NVIC to not use the running_irq and last_active internal
state fields in the GIC. These fields don't correspond to state in
a real GIC and will be removed soon.
The changes to the ICSR are:
* the VECTACTIVE field is documented as identical to the IPSR[8:0]
field, so implement it that way
* implement RETTOBASE via looking at the active state bits
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1438089748-5528-2-git-send-email-peter.maydell@linaro.org
Grouping (GICv2) and Security Extensions change the behavior of IAR
reads. Acknowledging Group0 interrupts is only allowed from Secure
state and acknowledging Group1 interrupts from Secure state is only
allowed if AckCtl bit is set.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1430502643-25909-14-git-send-email-peter.maydell@linaro.org
Message-id: 1429113742-8371-14-git-send-email-greg.bellows@linaro.org
[PMM: simplify significantly by reusing the existing
gic_get_current_pending_irq() rather than reimplementing the
same logic here]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Grouping (GICv2) and Security Extensions change the behavior of EOIR
writes. Completing Group0 interrupts is only allowed from Secure state.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1430502643-25909-13-git-send-email-peter.maydell@linaro.org
Message-id: 1429113742-8371-13-git-send-email-greg.bellows@linaro.org
[PMM: Rather than go to great lengths to ignore the UNPREDICTABLE case
of a Secure EOI of a Group1 (NS) irq with AckCtl == 0, we just let
it fall through; add a comment about it.]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
ICCICR/GICC_CTLR is banked in GICv1 implementations with Security
Extensions or in GICv2 in independent from Security Extensions.
This makes it possible to enable forwarding of interrupts from
the CPU interfaces to the connected processors for Group0 and Group1.
We also allow to set additional bits like AckCtl and FIQEn by changing
the type from bool to uint32. Since the field does not only store the
enable bit anymore and since we are touching the vmstate, we use the
opportunity to rename the field to cpu_ctlr.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1430502643-25909-9-git-send-email-peter.maydell@linaro.org
Message-id: 1429113742-8371-9-git-send-email-greg.bellows@linaro.org
[PMM: rewrote to store state in a single uint32_t rather than
keeping the NS and S banked variants separate; this considerably
simplifies the get/set functions]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
ICDDCR/GICD_CTLR is banked if the GIC has the security extensions,
and the S (or only) copy has separate enable bits for Group0 and
Group1 enable if the GIC implements interrupt groups.
EnableGroup0 (Bit [1]) in GICv1 is architecturally IMPDEF. Since this
bit (Enable Non-secure) is present in the integrated GIC of the Cortex-A9
MPCore, we support this bit in our GICv1 implementation too.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1430502643-25909-7-git-send-email-peter.maydell@linaro.org
Message-id: 1429113742-8371-8-git-send-email-greg.bellows@linaro.org
[PMM: rewritten to store the state in a single s->ctlr uint32,
with the NS register handled as an alias of bit 1 in that value;
added vmstate version bump]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Consider the following pseudo code to configure SYSTICK (The
recommended programming sequence from "the definitive guide to the
arm cortex-m3"):
SYSTICK Reload Value Register = 0xffff
SYSTICK Current Value Register = 0
SYSTICK Control and Status Register = 0x7
The pseudo code "SYSTICK Current Value Register = 0" leads to invoking
systick_reload(). As a consequence, the systick.tick member is updated
and the systick timer starts to count down when the ENABLE bit of
SYSTICK Control and Status Register is cleared.
The worst case is that: during the system initialization, the reset
value of the SYSTICK Control and Status Register is 0x00000000.
When the code "SYSTICK Current Value Register = 0" is executed, the
systick.tick member is accumulated with "(s->systick.reload + 1) *
systick_scale(s)". The systick_scale() gets the external_ref_clock
scale because the CLKSOURCE bit of the SYSTICK Control and Status
Register is cleared. This is the incorrect behavior because of the
code "SYSTICK Control and Status Register = 0x7". Actually, we want
the processor clock instead of the external reference clock.
This incorrect behavior defers the generation of the first interrupt.
The patch fixes the above-mentioned issue by setting the systick.tick
member and modifying the systick timer only if the ENABLE bit of
the SYSTICK Control and Status Register is set.
In addition, the Cortex-M3 Devices Generic User Guide mentioned that
"When ENABLE is set to 1, the counter loads the RELOAD value from the
SYST RVR register and then counts down". This patch adheres to the
statement of the user guide.
Signed-off-by: Adrian Huang <adrianhuang0701@gmail.com>
Reviewed-by: Jim Huang <jserv.tw@gmail.com>
[PMM: minor tweak to comment text]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This removes num_irq parameter from gic_init_irqs_and_distributor as it is not
used.
Signed-off-by: KONRAD Frederic <fred.konrad@greensocs.com>
Message-id: 1412859651-15060-1-git-send-email-fred.konrad@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The returned reset value was wrong (off by one zero nibble), and
qemu didn't log unimplemented writes to the PRIGROUP field.
Signed-off-by: Oran Avraham <oranav@gmail.com>
Message-id: 1403010447-4627-1-git-send-email-oranav@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
After commit 767adce2d, they are redundant. This way we don't assign them
except when needed. Once there, there were lots of cases where the ".fields"
indentation was wrong:
.fields = (VMStateField []) {
and
.fields = (VMStateField []) {
Change all the combinations to:
.fields = (VMStateField[]){
The biggest problem (apart from aesthetics) was that checkpatch complained
when we copy&pasted the code from one place to another.
Signed-off-by: Juan Quintela <quintela@redhat.com>
[PMM: fixed minor conflict, corrected commit message typos]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Using error_is_set(ERRP) to find out whether a function failed is
either wrong, fragile, or unnecessarily opaque. It's wrong when ERRP
may be null, because errors go undetected when it is. It's fragile
when proving ERRP non-null involves a non-local argument. Else, it's
unnecessarily opaque (see commit 84d18f0).
I guess the error_is_set(errp) in the DeviceClass realize() methods
are merely fragile right now, because I can't find a call chain that
passes a null errp argument.
Make the code more robust and more obviously correct: receive the
error in a local variable, then propagate it through the parameter.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
cp15.c0_cpuid is never initialized for ARMv7-M; take the value directly
from cpu->midr instead.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Message-id: 1398036308-32166-1-git-send-email-rabin@rab.in
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is an autogenerated patch using scripts/switch-timer-api.
Switch the entire code base to using the new timer API.
Note this patch may introduce some line length issues.
Signed-off-by: Alex Bligh <alex@alex.org.uk>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The recent rearrangement of include files had some minor errors:
devices.h is not ARM specific and should not be in arm/
arm.h should be in arm/
Move these two headers to correct this.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Minor fixes to documentation and code comments.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
