This fixes another failure with ExtINT, demonstrated by QNX. The failure
mode is as follows:
- IPI sent to cpu 0 (bit set in APIC irr)
- IPI accepted by cpu 0 (bit cleared in irr, set in isr)
- IPI sent to cpu 0 (bit set in both irr and isr)
- PIC interrupt sent to cpu 0
The PIC interrupt causes CPU_INTERRUPT_HARD to be set, but
apic_irq_pending observes that the highest pending APIC interrupt priority
(the IPI) is the same as the processor priority (since the IPI is still
being handled), so apic_get_interrupt returns a spurious interrupt rather
than the pending PIC interrupt. The result is an endless sequence of
spurious interrupts, since nothing will clear CPU_INTERRUPT_HARD.
Instead, ExtINT interrupts should have ignored the processor priority.
Calling apic_check_pic early in apic_get_interrupt ensures that
apic_deliver_pic_intr is called instead of delivering the spurious
interrupt. apic_deliver_pic_intr then clears CPU_INTERRUPT_HARD if needed.
Reported-by: Richard Bilson <rbilson@qnx.com>
Tested-by: Richard Bilson <rbilson@qnx.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch fixes an obscure failure of the QNX kernel on QEMU x86 SMP.
In QNX, all hardware interrupts come via the PIC, and are delivered by
the cpu 0 LAPIC in ExtINT mode, while IPIs are delivered by the LAPIC
in fixed mode.
This bug happens as follows:
- cpu 0 masks a particular PIC interrupt
- IPI sent to cpu 0 (CPU_INTERRUPT_HARD is set)
- before the IPI is accepted, the masked interrupt line is asserted by the
device
Since the interrupt is masked, apic_deliver_pic_intr will clear
CPU_INTERRUPT_HARD. The IPI will still be set in the APIC irr, but since
CPU_INTERRUPT_HARD is not set the cpu will not notice. Depending on the
scenario this can cause a system hang, i.e. if cpu 0 is expected to unmask
the interrupt.
In order to fix this, do a full check of the APIC before an EXTINT
is acknowledged. This can result in clearing CPU_INTERRUPT_HARD, but
can also result in delivering the lost IPI.
Reported-by: Richard Bilson <rbilson@qnx.com>
Tested-by: Richard Bilson <rbilson@qnx.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
After the next patch, if a masked PIC interrupts causes CPU_INTERRUPT_POLL
to be set, the CPU will spuriously get out of halted state. While this
is technically valid, we should avoid that.
Make CPU_INTERRUPT_POLL run apic_update_irq in the right thread and then
look at CPU_INTERRUPT_HARD. If CPU_INTERRUPT_HARD does not get set,
do not report the CPU as having work.
Also move the handling of software-disabled APIC from apic_update_irq
to apic_irq_pending, and always trigger CPU_INTERRUPT_POLL. This will
be important once we will add a case that resets CPU_INTERRUPT_HARD
from apic_update_irq. We want to run it even if we go through
CPU_INTERRUPT_POLL, and even if the local APIC is software disabled.
Reported-by: Richard Bilson <rbilson@qnx.com>
Tested-by: Richard Bilson <rbilson@qnx.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch adds missed sipi_vector and wait_for_sipi fields to a new
subsection of the vmstate of the apic_common module. Saving and loading
of these fields makes migration of the apic state deterministic.
Signed-off-by: Pavel Dovgalyuk <Pavel.Dovgaluk@ispras.ru>
[Initialize the field in pre_load and kvm_apic_realize. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The in-kernel OpenPIC emulation only supports a single map. However, we
map the OpenPIC at 2 locations: The CPU visible one and the PCI visible
one. For KVM acceleration, we only care about the first one.
To make sure that we only map that first mapping and not the PCI map that
happens dynamically later during bootup, ignore maps that happen when
we are already considering ourselves mapped.
Credits due are to Bogdan and Mihai for debugging this.
Reported-by: Bogdan Purcareata <bogdan.purcareata@freescale.com>
Reported-by: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This removes num_irq parameter from gic_init_irqs_and_distributor as it is not
used.
Signed-off-by: KONRAD Frederic <fred.konrad@greensocs.com>
Message-id: 1412859651-15060-1-git-send-email-fred.konrad@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Steps:
1.enable qemu debug print, using simply scprit as below:
grep "//#define DEBUG" * -rl | xargs sed -i "s/\/\/#define DEBUG/#define DEBUG/g"
2. make -j
3. get some warning:
hw/i2c/pm_smbus.c: In function 'smb_ioport_writeb':
hw/i2c/pm_smbus.c:142: warning: format '%04x' expects type 'unsigned int', but argument 2 has type 'hwaddr'
hw/i2c/pm_smbus.c:142: warning: format '%02x' expects type 'unsigned int', but argument 3 has type 'uint64_t'
hw/i2c/pm_smbus.c: In function 'smb_ioport_readb':
hw/i2c/pm_smbus.c:209: warning: format '%04x' expects type 'unsigned int', but argument 2 has type 'hwaddr'
hw/intc/i8259.c: In function 'pic_ioport_read':
hw/intc/i8259.c:373: warning: format '%02x' expects type 'unsigned int', but argument 2 has type 'hwaddr'
hw/input/pckbd.c: In function 'kbd_write_command':
hw/input/pckbd.c:232: warning: format '%02x' expects type 'unsigned int', but argument 2 has type 'uint64_t'
hw/input/pckbd.c: In function 'kbd_write_data':
hw/input/pckbd.c:333: warning: format '%02x' expects type 'unsigned int', but argument 2 has type 'uint64_t'
hw/isa/apm.c: In function 'apm_ioport_writeb':
hw/isa/apm.c:44: warning: format '%x' expects type 'unsigned int', but argument 2 has type 'hwaddr'
hw/isa/apm.c:44: warning: format '%02x' expects type 'unsigned int', but argument 3 has type 'uint64_t'
hw/isa/apm.c: In function 'apm_ioport_readb':
hw/isa/apm.c:67: warning: format '%x' expects type 'unsigned int', but argument 2 has type 'hwaddr'
hw/timer/mc146818rtc.c: In function 'cmos_ioport_write':
hw/timer/mc146818rtc.c:394: warning: format '%02x' expects type 'unsigned int', but argument 3 has type 'uint64_t'
hw/i386/pc.c: In function 'port92_write':
hw/i386/pc.c:479: warning: format '%02x' expects type 'unsigned int', but argument 2 has type 'uint64_t'
Fix them.
Cc: qemu-trivial@nongnu.org
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Take IRQ target mask into account when determining the highest priority
pending interrupt.
Signed-off-by: Sergey Fedorov <serge.fdrv@gmail.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Message-id: 1407947471-26981-1-git-send-email-serge.fdrv@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use constant rather than a plain number.
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Adam Lackorzynski <adam@os.inf.tu-dresden.de>
Message-id: 1408372255-12358-5-git-send-email-adam@os.inf.tu-dresden.de
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Only SGIs must be WI, done by forcing them to their default
(edge-triggered).
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Adam Lackorzynski <adam@os.inf.tu-dresden.de>
Message-id: 1408372255-12358-4-git-send-email-adam@os.inf.tu-dresden.de
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Setting the model is only available in pre-v1 GIC models.
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Adam Lackorzynski <adam@os.inf.tu-dresden.de>
Message-id: 1408372255-12358-3-git-send-email-adam@os.inf.tu-dresden.de
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The GICD_ICFGR register covers 4 interrupts per byte.
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Adam Lackorzynski <adam@os.inf.tu-dresden.de>
Message-id: 1408372255-12358-2-git-send-email-adam@os.inf.tu-dresden.de
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
To be more array friendly and to indicate the IRQs are initially
disconnected.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
To indicate the IRQs are initially disconnected.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
This implements interrupt release function so IRQs can be returned back
to the pool for reuse in cases such as PCI hot plug.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alexander Graf <agraf@suse.de>
The current allocator returns IRQ numbers from a pool and does not
support IRQs reuse in any form as it did not keep track of what it
previously returned, it only keeps the last returned IRQ. Some use
cases such as PCI hot(un)plug may require IRQ release and reallocation.
This moves an allocator from SPAPR to XICS.
This switches IRQ users to use new API.
This uses LSI/MSI flags to know if interrupt is allocated.
The interrupt release function will be posted as a separate patch.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alexander Graf <agraf@suse.de>
Since islsi[] array has been merged into the ICSState struct,
we must not reset flags as they tell if the interrupt is in use.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alexander Graf <agraf@suse.de>
PAPR allows having multiple interrupt sources such as PHB.
This adds a source lookup function and makes use of it.
Since at the moment QEMU only supports a single source,
no change in behaviour is expected.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alexander Graf <agraf@suse.de>
The existing interrupt allocation scheme in SPAPR assumes that
interrupts are allocated at the start time, continously and the config
will not change. However, there are cases when this is not going to work
such as:
1. migration - we will have to have an ability to choose interrupt
numbers for devices in the command line and this will create gaps in
interrupt space.
2. PCI hotplug - interrupts from unplugged device need to be returned
back to interrupt pool, otherwise we will quickly run out of interrupts.
This replaces a separate lslsi[] array with a byte in the ICSIRQState
struct and defines "LSI" and "MSI" flags. Neither of these flags set
signals that the descriptor is not allocated and not in use.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alexander Graf <agraf@suse.de>
At the moment spapr_rtas_register() allocates a new token number for every
new RTAS callback so numbers are not fixed and depend on the number of
supported RTAS handlers and the exact order of spapr_rtas_register() calls.
These tokens are copied into the device tree and remain the same during
the guest lifetime.
When we start another guest to receive a migration, it calls
spapr_rtas_register() as well. If the number of RTAS handlers or their
order is different in QEMU on source and destination sides, the "/rtas"
node in the device tree will differ. Since migration overwrites the device
tree (as it overwrites the entire RAM), the actual RTAS config on
the destination side gets broken.
This defines global contant values for every RTAS token which QEMU
is using today.
This changes spapr_rtas_register() to accept a token number instead of
allocating one. This changes all users of spapr_rtas_register().
This changes XICS-KVM not to cache tokens registered with KVM as they
constant now.
This makes TOKEN_BASE global as RTAS_XXX use TOKEN_BASE as
a base. TOKEN_MAX is moved and renamed too and its value is changed
to the last token + 1. Boundary checks for token values are adjusted.
This reserves token numbers for "os-term" handlers and PCI hotplug
which we are working on.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alexander Graf <agraf@suse.de>
The returned reset value was wrong (off by one zero nibble), and
qemu didn't log unimplemented writes to the PRIGROUP field.
Signed-off-by: Oran Avraham <oranav@gmail.com>
Message-id: 1403010447-4627-1-git-send-email-oranav@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When we trigger a system reset, the in-kernel openpic controller should also
get reset. This happens through a write to the GCR.RESET register which is
the same mechanism a guest would use to manually reset the device.
Signed-off-by: Alexander Graf <agraf@suse.de>
The openpic emulation code maintains an allowable-CPU's bitmap
("destmask") for each IRQ source which is calculated from the IDR
register value whenever the guest OS writes to it. However, if the
guest OS relies on the system to set the IDR register to a default
value at reset, and does not write IDR, then destmask does not get
updated, and interrupts do not get propagated to the guest.
Additionally, if an IRQ source is marked as critical, the source's
internal "output" and "nomask" fields are not correctly reset when the
PIC is reset.
Fix both these issues by calling write_IRQreg_idr from within
openpic_reset, instead of simply setting the IDR register to the
specified idr_reset value.
Signed-off-by: Paul Janzen <pcj@pauljanzen.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch moves the definition of openpic_reset after the various
register read/write functions. No functional change. It is in
preparation for using the register read/write functions in
openpic_reset.
Signed-off-by: Paul Janzen <pcj@pauljanzen.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
After previous Peter patch, they are redundant. This way we don't
assign them except when needed. Once there, there were lots of case
where the ".fields" indentation was wrong:
.fields = (VMStateField []) {
and
.fields = (VMStateField []) {
Change all the combinations to:
.fields = (VMStateField[]){
The biggest problem (appart from aesthetics) was that checkpatch complained
when we copy&pasted the code from one place to another.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Acked-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
After previous Peter patch, they are redundant. This way we don't
assign them except when needed. Once there, there were lots of case
where the ".fields" indentation was wrong:
.fields = (VMStateField []) {
and
.fields = (VMStateField []) {
Change all the combinations to:
.fields = (VMStateField[]){
The biggest problem (appart from aesthetics) was that checkpatch complained
when we copy&pasted the code from one place to another.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Acked-by: Alexey Kardashevskiy <aik@ozlabs.ru>
The IRQ_testbit() function is never used; remove it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Try to inject floating interrupts via the flic if it is available.
This allows us to inject the full range of floating interrupts.
Reviewed-by: Jens Freimann <jfrei@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
If we run with an old kernel that does not support KVM_CAP_IRQ_ROUTING,
we don't have to do anything in the ->register_io_adapter and
->io_adapter_map callbacks and therefore should return 0 instead of
-ENOSYS (just as the non-kvm flic does).
This fixes using adapter interrupts when running under an older kernel,
which broke with "s390x: add I/O adapter registration".
Reported-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
SysBusDevice::init is depracated. Convert to Object::init
as prescribed by QOM conventions.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Make use of the new s390 adapter irq routing support to enable real
in-kernel irqfds for virtio-ccw with adapter interrupts.
Note that s390 doesn't provide the common KVM_CAP_IRQCHIP capability, but
rather needs KVM_CAP_S390_IRQCHIP to be enabled. This is to ensure backward
compatibility.
Reviewed-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Register an I/O adapter interrupt source for when virtio-ccw devices start
using adapter interrupts.
Reviewed-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Introduce a common parent class for both cases, where kvm and non-kvm
can hook up callbacks. This will be used by follow-on patches for
adapter registration and mapping.
We now always have a flic, regardless of whether we use kvm; the
non-kvm implementation just doesn't do anything.
Reviewed-by: Jens Freimann <jfrei@linux.vnet.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=gg8m
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/juanquintela/tags/migration/20140515' into staging
migration/next for 20140515
# gpg: Signature made Thu 15 May 2014 02:32:25 BST using RSA key ID 5872D723
# gpg: Can't check signature: public key not found
* remotes/juanquintela/tags/migration/20140515:
usb: fix up post load checks
migration: show average throughput when migration finishes
savevm: Remove all the unneeded version_minimum_id_old (rest)
savevm: Remove all the unneeded version_minimum_id_old (usb)
Split ram_save_block
arch_init: Simplify code for load_xbzrle()
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
After previous Peter patch, they are redundant. This way we don't
assign them except when needed. Once there, there were lots of case
where the ".fields" indentation was wrong:
.fields = (VMStateField []) {
and
.fields = (VMStateField []) {
Change all the combinations to:
.fields = (VMStateField[]){
The biggest problem (appart from aesthetics) was that checkpatch complained
when we copy&pasted the code from one place to another.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Add missing 'break' after handling of AW_A10_PIC_BASE_ADDR write.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
After commit 767adce2d, they are redundant. This way we don't assign them
except when needed. Once there, there were lots of cases where the ".fields"
indentation was wrong:
.fields = (VMStateField []) {
and
.fields = (VMStateField []) {
Change all the combinations to:
.fields = (VMStateField[]){
The biggest problem (apart from aesthetics) was that checkpatch complained
when we copy&pasted the code from one place to another.
Signed-off-by: Juan Quintela <quintela@redhat.com>
[PMM: fixed minor conflict, corrected commit message typos]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
SIPI interrupts are ignored on the bootstrap. Never accept one.
Cc: Andreas Faerber <afaerber@suse.de>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The MER register only has two valid bits. This is now used by
the linux kernel to auto-detect endianness, and causes Linux 3.15-rc1
and later to hang when run under qemu-microblaze. Mask valid bits before
writing the register to solve the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
[Edgar: Untabified]
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
MAINTAINERS updated with link to the security process documentation
apic version modified to make more guests happy
On top of that, bugfixes all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTalwhAAoJECgfDbjSjVRpyqcIAKniYsCcKiUjIpTjo4hSHkNN
zBfMlnqyFNMB8e6rQ7yqt8WCp/fzzsiqjYF07Ycmcmfnbfh907C90Ei37CWQpObv
GlY41Qx4qUJxYbrqXJCcmOoR+UmAhrIzlr4TLs4DuasLglXGaPla0PcQgzYCNxsk
m6f2FvyazAkr4FpT+y67YceHM6xlBoPOI2wLPcSPXWN775xZdfA/w/oFcTRdKlny
V9Eo2WTKtQXrz5rPg9U+jLJhKn1e67DHt2CoQqvQtMg2BUSX7YmLdzF3N5I4eiwt
DYPf4YO/LIJnkKpKVWFLrYWwccXDacSvqIDQOuCU0nydlHnXviGRcUIWh15x0a8=
=vbBe
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pc,net,MAINTAINERS,build updates
MAINTAINERS updated with link to the security process documentation
apic version modified to make more guests happy
On top of that, bugfixes all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Wed 07 May 2014 17:15:29 BST using RSA key ID D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
* remotes/mst/tags/for_upstream:
configure: make source tree build more robust
MAINTAINERS: addresses for responsible disclosure
pm_smbus: correctly report unclaimed cycles
smbus: return -1 if nothing found at the given address
smbus: allow returning an error from reads
apic: use emulated lapic version 0x14 on pc machines >= 2.1
pc: add compat_props placeholder for 2.0 machine type
i8259: don't abort when trying to use level sensitive irqs
acpi: fix tables for no-hpet configuration
acpi-build: properly decrement objects' reference counters
acpi/pcihp.c: Rewrite acpi_pcihp_get_bsel using object_property_get_int
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add "version" property to local apic, and have it default to
0x14 for pc machines starting at 2.1. For compatibility with
previous releases, pc machines up to 2.0 will have their local
apic version set to 0x11.
Signed-off-by: Gabriel L. Somlo <somlo@cmu.edu>
Acked-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This is a guest-triggerable error, as seen when using Xenix 2.3.4.
Replace hw_error by LOG_UNIMPL, so that guests can continue.
With this patch, I can install and use Xenix 2.3.4a without any problem.
I can also start installation of Xenix 2.3.4q, but it fails due to not
finding an hard disk.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=VoYL
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/juanquintela/tags/migration/20140505' into staging
migration/next for 20140505
# gpg: Signature made Mon 05 May 2014 21:27:24 BST using RSA key ID 5872D723
# gpg: Can't check signature: public key not found
* remotes/juanquintela/tags/migration/20140505: (36 commits)
migration: expose xbzrle cache miss rate
migration: expose the bitmap_sync_count to the end
migration: Add counts of updating the dirty bitmap
XBZRLE: Fix one XBZRLE corruption issues
migration: remove duplicate code
Coverity: Fix failure path for qemu_accept in migration
Init the XBZRLE.lock in ram_mig_init
Provide init function for ram migration
Count used RAMBlock pages for migration_dirty_pages
Make qemu_peek_buffer loop until it gets it's data
Disallow outward migration while awaiting incoming migration
virtio: validate config_len on load
virtio-net: out-of-bounds buffer write on load
openpic: avoid buffer overrun on incoming migration
ssi-sd: fix buffer overrun on invalid state load
savevm: Ignore minimum_version_id_old if there is no load_state_old
usb: sanity check setup_index+setup_len in post_load
vmstate: s/VMSTATE_INT32_LE/VMSTATE_INT32_POSITIVE_LE/
virtio-scsi: fix buffer overrun on invalid state load
zaurus: fix buffer overrun on invalid state load
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
CVE-2013-4534
opp->nb_cpus is read from the wire and used to determine how many
IRQDest elements to read into opp->dst[]. If the value exceeds the
length of opp->dst[], MAX_CPU, opp->dst[] can be overrun with arbitrary
data from the wire.
Fix this by failing migration if the value read from the wire exceeds
MAX_CPU.
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Using error_is_set(ERRP) to find out whether a function failed is
either wrong, fragile, or unnecessarily opaque. It's wrong when ERRP
may be null, because errors go undetected when it is. It's fragile
when proving ERRP non-null involves a non-local argument. Else, it's
unnecessarily opaque (see commit 84d18f0).
I guess the error_is_set(errp) in the DeviceClass realize() methods
are merely fragile right now, because I can't find a call chain that
passes a null errp argument.
Make the code more robust and more obviously correct: receive the
error in a local variable, then propagate it through the parameter.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
* implement XScale cache lockdown cp15 ops
* fix v7M CPUID base register
* implement WFE and YIELD as yields for A64
* fix A64 "BLR LR"
* support Cortex-A57 in virt machine model
* a few other minor AArch64 bugfixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=F2C9
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20140501' into staging
target-arm queue:
* implement XScale cache lockdown cp15 ops
* fix v7M CPUID base register
* implement WFE and YIELD as yields for A64
* fix A64 "BLR LR"
* support Cortex-A57 in virt machine model
* a few other minor AArch64 bugfixes
# gpg: Signature made Thu 01 May 2014 15:42:17 BST using RSA key ID 14360CDE
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>"
* remotes/pmaydell/tags/pull-target-arm-20140501:
hw/arm/virt: Add support for Cortex-A57
hw/arm/virt: Put GIC register banks on 64K boundaries
hw/arm/virt: Create the GIC ourselves rather than (ab)using a15mpcore_priv
target-arm: Correct a comment refering to EL0
target-arm: A64: Fix a typo when declaring TLBI ops
target-arm: A64: Handle blr lr
target-arm: Make vbar_write 64bit friendly on 32bit hosts
target-arm: implement WFE/YIELD as a yield for AArch64
armv7m_nvic: fix CPUID Base Register
target-arm: Implement XScale cache lockdown operations as NOPs
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
cp15.c0_cpuid is never initialized for ARMv7-M; take the value directly
from cpu->midr instead.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Message-id: 1398036308-32166-1-git-send-email-rabin@rab.in
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Convert existing users of KVM_ENABLE_CAP to new helper.
Reviewed-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
These functions don't need type casts (as does cpu_physical_memory_rw)
and also make the code better readable.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The pending register is read-only and the value returned upon a read
reflects the state of irq input pins (interrupts are level triggered).
This patch implements such behaviour.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Li Guang <lig.fnst@cn.fujitsu.com>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: 1395771730-16882-3-git-send-email-b.galvani@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch implements proper updating of the vector register which
should hold, according to the A10 user manual, the vector address for
the interrupt currently active on the CPU IRQ input.
Interrupt priority is not implemented at the moment and thus the first
pending interrupt is returned.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Li Guang <lig.fnst@cn.fujitsu.com>
Message-id: 1395771730-16882-2-git-send-email-b.galvani@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Commit 6f1834a2b exposed a bug in openpic_kvm where we don't filter
for memory events that only happen to the region we want to know
events about.
Add proper filtering, fixing the e500plat target with KVM.
Signed-off-by: Alexander Graf <agraf@suse.de>
Message-id: 1396431718-14908-1-git-send-email-agraf@suse.de
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
SystemTap sdt.h sometimes results in compiled probes without sufficient
information to extract arguments. This can be solved in a slightly
hacky way by encouraging the compiler to place arguments into registers.
This patch fixes the apic_reset_irq_delivered() trace event on Fedora 20
with gcc-4.8.2-7.fc20 and systemtap-sdt-devel-2.4-2.fc20 on x86_64.
Signed-off-by: Frank Ch. Eigler <fche@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Avoid undefined behaviour shifting left into the sign bit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Add U suffix to avoid undefined behaviour. This is only strictly
necessary for the 1 << 31 cases; for consistency we extend it
to other constants in the same group.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Use unsigned arithmetic for operations on the mask word
in the foreach_apic() macro, to avoid relying on undefined
behaviour when shifting into the sign bit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Codespell found and fixed these new typos:
* doesnt -> doesn't
* funtion -> function
* perfomance -> performance
* remaing -> remaining
A coding style issue (line too long) was fixed manually.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Currently interrupt priorities are set to 0 (highest) at the very
beginning of the guest execution which is not correct and makes the guest
produce random interrupt error messages such as:
"Interrupt 0x1001 (real) is invalid, disabling it".
This also prevents interrupt states from correct migration.
This initializes priority to 0xFF as the emulated XICS does.
Suggested-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Both QEMU and KVM have already accumulated a significant number of
optimizations based on the hard-coded assumption that ioapic polarity
will always use the ActiveHigh convention, where the logical and
physical states of level-triggered irq lines always match (i.e.,
active(asserted) == high == 1, inactive == low == 0). QEMU guests
are expected to follow directions given via ACPI and configure the
ioapic with polarity 0 (ActiveHigh). However, even when misbehaving
guests (e.g. OS X <= 10.9) set the ioapic polarity to 1 (ActiveLow),
QEMU will still use the ActiveHigh signaling convention when
interfacing with the emulated ioapic.
This patch modifies the emulated ioapic to completely ignore polarity
as set by the guest OS, enabling misbehaving guests to work alongside
those which comply with the ActiveHigh polarity specified by QEMU's
ACPI tables.
Signed-off-by: Gabriel L. Somlo <somlo@cmu.edu>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This makes use of @cpu_dt_id and related API in:
1. emulated XICS hypercall handlers as they receive fixed CPU indexes;
2. XICS-KVM to enable in-kernel XICS on right CPU;
3. device-tree renderer.
This removes @cpu_index fixup as @cpu_dt_id is used instead so QEMU monitor
can accept command-line CPU indexes again.
This changes kvm_arch_vcpu_id() to use ppc_get_vcpu_dt_id() as at the moment
KVM CPU id and device tree ID are calculated using the same algorithm.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Mike Day <ncmike@ncultra.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
- sclp event facility: cleanup structure. This allows to use
realize/unrealize as well as migration support via vmsd
- reboot: Two fixes that make reboot much more reliable
- ipl: make elf loading more robust
- flic interrupt controller: This allows to migrate floating
interrupts, as well as clear them on reset etc.
- enable async_pf feature of KVM on s390
- several sclp fixes and cleanups
- several sigp fixes and cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=toIt
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/borntraeger/tags/kvm-s390-20140227' into staging
Several features, fixes and cleanups for kvm/s390:
- sclp event facility: cleanup structure. This allows to use
realize/unrealize as well as migration support via vmsd
- reboot: Two fixes that make reboot much more reliable
- ipl: make elf loading more robust
- flic interrupt controller: This allows to migrate floating
interrupts, as well as clear them on reset etc.
- enable async_pf feature of KVM on s390
- several sclp fixes and cleanups
- several sigp fixes and cleanups
* remotes/borntraeger/tags/kvm-s390-20140227: (22 commits)
s390x/ipl: Fix crash of ELF images with arbitrary entry points
s390x/kvm: Rework priv instruction handlers
s390x/kvm: Add missing SIGP CPU RESET order
s390x/kvm: Rework SIGP INITIAL CPU RESET handler
s390x/cpu: Use ioctl to reset state in the kernel
s390-ccw.img: new binary rom to match latest fixes
s390-ccw.img: Fix sporadic errors with ccw boot image - initialize css
s390-ccw.img: Fix sporadic reboot hangs: Initialize next_idx
s390x/event-facility: exploit realize/unrealize
s390x/event-facility: add support for live migration
s390x/event-facility: code restructure
s390x/event-facility: some renaming
s390x/sclp: Fixed setting of condition code register
s390x/sclp: Add missing checks to SCLP handler
s390x/sclp: Fixed the size of sccb and code parameter
s390x/eventfacility: mask out commands
s390x/virtio-hcall: Specification exception for illegal subcodes
s390x/virtio-hcall: Add range check for hypervisor call
s390x/kvm: Fixed bad SIGP SET-ARCHITECTURE handler
s390x/async_pf: Check for apf extension and enable pfault
...
Conflicts:
linux-headers/linux/kvm.h
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
S390 can also use async page faults, to enhance guest scheduling.
In case of live migration we want to disable the feature and let
all pending request finish.
Signed-off-by: Dominik Dingel <dingel@linux.vnet.ibm.com>
Signed-off-by: Jens Freimann <jfrei@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
This patch implements a floating-interrupt controller device (flic)
which interacts with the s390 flic kvm_device.
Signed-off-by: Jens Freimann <jfrei@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Save and restore the ARM KVM VGIC state from the kernel. We rely on
QEMU to marshal the GICState data structure and therefore simply
synchronize the kernel state with the QEMU emulated state in both
directions.
We take some care on the restore path to check the VGIC has been
configured with enough IRQs and CPU interfaces that we can properly
restore the state, and for separate set/clear registers we first fully
clear the registers and then set the required bits.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Message-id: 1392687921-26921-1-git-send-email-christoffer.dall@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Support creating the ARM vgic device through the device control API and
setting the base address for the distributor and cpu interfaces in KVM
VMs using this API.
Because the older KVM_CREATE_IRQCHIP interface needs the irq chip to be
created prior to creating the VCPUs, we first test if we can use the
device control API in kvm_arch_irqchip_create (using the test flag from
the device control API). If we cannot, it means we have to fall back to
KVM_CREATE_IRQCHIP and use the older ioctl at this point in time. If
however, we can use the device control API, we don't do anything and
wait until the arm_gic_kvm driver initializes and let that use the
device control API.
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Message-id: 1392687720-26806-5-git-send-email-christoffer.dall@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The GIC_SET_LEVEL macro unfortunately overwrote the entire level
bitmask instead of just or'ing on the necessary bits, causing active
level PPIs on a core to clear PPIs on other cores.
Cc: qemu-stable@nongnu.org
Reported-by: Rob Herring <rob.herring@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Message-id: 1393031030-8692-1-git-send-email-christoffer.dall@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Exynos4210 combiner has IIC_NIRQ inputs and IIC_NGRP outputs;
use the correct constant in the loop initializing our output
sysbus IRQs so that we don't overrun the output_irq[] array.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1392659611-8439-1-git-send-email-peter.maydell@linaro.org
Reviewed-by: Andreas Färber <afaerber@suse.de>
Cc: qemu-stable@nongnu.org
* Fix a bug causing an assertion in the NVIC on ARMv7M models
* More A64 Neon instructions
* Refactor cpreg API to separate out access check functions, as
groundwork for AArch64 system mode
* Fix bug in linux-user A64 store-exclusive of XZR
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=h/1p
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20140220' into staging
target-arm queue:
* Fix a bug causing an assertion in the NVIC on ARMv7M models
* More A64 Neon instructions
* Refactor cpreg API to separate out access check functions, as
groundwork for AArch64 system mode
* Fix bug in linux-user A64 store-exclusive of XZR
# gpg: Signature made Thu 20 Feb 2014 11:12:57 GMT using RSA key ID 14360CDE
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>"
* remotes/pmaydell/tags/pull-target-arm-20140220: (30 commits)
linux-user: AArch64: Fix exclusive store of the zero register
target-arm: A64: Implement unprivileged load/store
target-arm: A64: Implement narrowing three-reg-diff operations
target-arm: A64: Implement the wide 3-reg-different operations
target-arm: A64: Add most remaining three-reg-diff widening ops
target-arm: A64: Add opcode comments to disas_simd_three_reg_diff
target-arm: A64: Implement store-exclusive for system mode
target-arm: Fix incorrect type for value argument to write_raw_cp_reg
target-arm: Remove failure status return from read/write_raw_cp_reg
target-arm: Remove unnecessary code now read/write fns can't fail
target-arm: Drop success/fail return from cpreg read and write functions
target-arm: Convert miscellaneous reginfo structs to accessfn
target-arm: Convert generic timer reginfo to accessfn
target-arm: Convert performance monitor reginfo to accessfn
target-arm: Split cpreg access checks out from read/write functions
target-arm: Stop underdecoding ARM946 PRBS registers
target-arm: Log bad system register accesses with LOG_UNIMP
target-arm: Remove unused ARMCPUState sr substruct
target-arm: Restrict check_ap() use of S and R bits to v6 and earlier
target-arm: Define names for SCTLR bits
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Commit 40d225009e accidentally changed the behaviour of
gic_acknowledge_irq() for the NVIC. The NVIC doesn't have SGIs,
so this meant we hit an assertion:
gic_acknowledge_irq: Assertion `s->sgi_pending[irq][cpu] != 0' failed.
Return NVIC acknowledge-irq to its previous behaviour, like 11MPCore.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Replace them with uint8/32/64.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
The GICC_APRn registers are not currently supported by the ARM GIC v2.0
emulation. This patch adds the missing state.
Note that we also change the number of APRs to use a define GIC_NR_APRS
based on the maximum number of preemption levels. This patch also adds
RAZ/WI accessors for the four registers on the emulated CPU interface.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a binary_point field to the gic emulation structure and support
setting/getting this register now when we have it. We don't actually
support interrupt grouping yet, oh well.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Right now the arm gic emulation doesn't keep track of the source of an
SGI (which apparently Linux guests don't use, or they're fine with
assuming CPU 0 always).
Add the necessary matrix on the GICState structure and maintain the data
when setting and clearing the pending state of an IRQ and make the state
visible to the guest.
Note that we always choose to present the source as the lowest-numbered
CPU in case multiple cores have signalled the same SGI number to a core
on the system.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The existing implementation of the pending behavior in gic_set_irq,
gic_complete_irq, and the distributor pending set/clear registers does
not follow the semantics of the GICv2.0 specs, but may implement the
11MPCore support. Therefore, maintain the existing semantics for
11MPCore and v7M NVIC and change the behavior to be in accordance with
the GICv2.0 specs for "generic implementations" (s->revision == 1 ||
s->revision == 2).
Generic implementations distinguish between setting a level-triggered
interrupt pending through writes to the GICD_ISPENDR and when hardware
raises the interrupt line. Writing to the GICD_ICPENDR will not cause
the interrupt to become non-pending if the line is still active, and
conversely, if the line is deactivated but the interrupt is marked as
pending through a write to GICD_ISPENDR, the interrupt remains pending.
Handle this situation in the GIC_TEST_PENDING (which now becomes a
static inline named gic_test_pending) and let the 'pending' field
correspond only to the latched state of the D-flip flop in the GICv2.0
specs Figure 4-10.
The following changes are added:
gic_test_pending:
Make this a static inline and split out the 11MPCore from the generic
behavior. For the generic behavior, consider interrupts pending if:
((s->irq_state[irq].pending & (cm) != 0) ||
(!GIC_TEST_EDGE_TRIGGER(irq) && GIC_TEST_LEVEL(irq, cm))
gic_set_irq:
Split out the 11MPCore from the generic behavior. For the generic
behavior, always GIC_SET_LEVEL() on positive level, but only
GIC_SET_PENDING for edge-triggered interrupts and always simply
GIC_CLEAR_LEVEL() on negative level.
gic_complete_irq:
Only resample the line for line-triggered interrupts on an 11MPCore.
Generic implementations will sample the line directly in
gic_test_pending().
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Fix two bugs that would allow changing the state of SGIs through the
ICPENDR and ISPENDRs.
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Instead of hardcoding 16 various places in the code, use a define to
make it more clear what is going on.
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* QOM interface fixes and unit test
* Device no_user sanitization and documentation
* Device error reporting improvement
* Conversion of APIC, ICC, IOAPIC to QOM realization model
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=WrhM
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'afaerber/tags/qom-devices-for-anthony' into staging
QOM infrastructure fixes and device conversions
* QOM interface fixes and unit test
* Device no_user sanitization and documentation
* Device error reporting improvement
* Conversion of APIC, ICC, IOAPIC to QOM realization model
# gpg: Signature made Tue 24 Dec 2013 09:04:05 AM PST using RSA key ID 3E7E013F
# gpg: Good signature from "Andreas Färber <afaerber@suse.de>"
# gpg: aka "Andreas Färber <afaerber@suse.com>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 174F 0347 1BCC 221A 6175 6F96 FA2E D12D 3E7E 013F
* afaerber/tags/qom-devices-for-anthony: (24 commits)
qdev-monitor: Improve error message for -device nonexistant
ioapic: QOM'ify ioapic
ioapic: Cleanup for QOM'ification
icc_bus: QOM'ify ICC
apic: QOM'ify APIC
apic: Cleanup for QOM'ification
qdev: Drop misleading qbus_free() function
qom: Detect bad reentrance during object_class_foreach()
tests: Test QOM interface casting
qom: Do not register interface "types" in the type table and fix names
qom: Split out object and class caches
qdev: Document that pointer properties kill device_add
hw: cannot_instantiate_with_device_add_yet due to pointer props
qdev-monitor: Avoid device_add crashing on non-device driver name
qdev: Do not let the user try to device_add when it cannot work
isa: Clean up use of cannot_instantiate_with_device_add_yet
vt82c686: Clean up use of cannot_instantiate_with_device_add_yet
piix3 piix4: Clean up use of cannot_instantiate_with_device_add_yet
ich9: Document why cannot_instantiate_with_device_add_yet
pci-host: Consistently set cannot_instantiate_with_device_add_yet
...
To make the code slightly cleaner to look at and make the save/restore
code easier to understand, introduce this function to set the priority of
interrupts.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Message-id: 1387606179-22709-3-git-send-email-christoffer.dall@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
TRIGGER can really mean mean anything (e.g. was it triggered, is it
level-triggered, is it edge-triggered, etc.). Rename to EDGE_TRIGGER to
make the code comprehensible without looking up the data structure.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Message-id: 1387606179-22709-2-git-send-email-christoffer.dall@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Convert 'init' function to QOM's 'realize' for ioapic and kvm-ioapic.
Change variable 'ioapic_no' from static to global. Then we can drop
the 'instance_no' function argument.
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Some cleanups:
* ioapic_common.c: Rename 'register_types' to 'ioapic_common_register_types'
* Replace inline 'DEVICE(s)' with local 'DeviceState *dev' variable
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Convert 'init' function to QOM's 'realize' for apic, kvm/apic and
xen/xen_apic.
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Do some cleanup, including:
1. Remove DO_UPCAST() for APICCommonState
2. Change DeviceState pointers from 'd' to 'dev', better to understand
3. Rename 'register_types' to specifically 'apic_common_register_types'
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Pointer properties can be set only by code, not by device_add. A
device with a pointer property can work with device_add only when the
property may remain null.
This is the case for property "interrupt_vector" of device
"etraxfs,pic". Add a comment there.
Set cannot_instantiate_with_device_add_yet for the other devices with
pointer properties, with a comment explaining why.
Juha Riihimäki and Peter Maydell deserve my thanks for making "pointer
property must not remain null" blatantly obvious in the OMAP devices.
Only device "smbus-eeprom" is actually changed. The others are all
sysbus devices, which get cannot_instantiate_with_device_add_yet set
in their abstract base's class init function. Setting it again in
their class init function is technically redundant, but serves as
insurance for when sysbus devices become available with device_add,
and as documentation.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@gmail.com> (for ETRAX)
Signed-off-by: Andreas Färber <afaerber@suse.de>
Drop it when there's no obvious reason why device_add could not work.
Else keep and document why.
* isa-fdc: drop
* i8042: drop, even though its I/O base is hardcoded (because you
could conceivably still add one to a board that has none), and even
though PC board code wires up the A20 line (because that wiring is
optional)
* port92: keep because it needs additional wiring by port92_init()
* mc146818rtc: keep because it needs to be wired up by rtc_init()
* m48t59_isa: keep because needs to be wired up by m48t59_init_isa()
* isa-pit, kvm-pit: keep (in their abstract base pic-common) because
the PIT needs additional wiring by board code, depending on HPET
presence
* pcspk: keep because of pointer property pit, and because realize
sets global pcspk_state
* vmmouse: keep because of pointer property ps2_mouse
* vmport: keep because realize sets global port_state
* isa-i8259, kvm-i8259: keep (in their abstract base pic-common),
because the PICs' IRQ input lines are set up by board code, and the
wiring of the slave to the master is hard-coded in device model code
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
device_add plugs devices into suitable bus. For "real" buses, that
actually connects the device. For sysbus, the connections need to be
made separately, and device_add can't do that. The device would be
left unconnected, and could not possibly work.
Quite a few, but not all sysbus devices already set
cannot_instantiate_with_device_add_yet in their class init function.
Set it in their abstract base's class init function
sysbus_device_class_init(), and remove the now redundant assignments
from device class init functions.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel.a@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
In an ideal world, machines can be built by wiring devices together
with configuration, not code. Unfortunately, that's not the world we
live in right now. We still have quite a few devices that need to be
wired up by code. If you try to device_add such a device, it'll fail
in sometimes mysterious ways. If you're lucky, you get an
unmysterious immediate crash.
To protect users from such badness, DeviceClass member no_user used to
make device models unavailable with -device / device_add, but that
regressed in commit 18b6dad. The device model is still omitted from
help, but is available anyway.
Attempts to fix the regression have been rejected with the argument
that the purpose of no_user isn't clear, and it's prone to misuse.
This commit clarifies no_user's purpose. Anthony suggested to rename
it cannot_instantiate_with_device_add_yet_due_to_internal_bugs, which
I shorten somewhat to keep checkpatch happy. While there, make it
bool.
Every use of cannot_instantiate_with_device_add_yet gets a FIXME
comment asking for rationale. The next few commits will clean them
all up, either by providing a rationale, or by getting rid of the use.
With that done, the regression fix is hopefully acceptable.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel.a@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Move state struct, type constant and cast macro to a new header.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Embed GICState and replace SysBus initfn with realizefn.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Rename NCPU to GIC_NCPU and move GICState away from gic_internal.h.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
This enables IRQFD support for sPAPR. The feature decreases the latency
of interrupt handling.
To enable IRQFD for MSI, this sets kvm_gsi_direct_mapping to true which
enables direct MSI mapping.
To enable IRQFD for LSI (level triggered INTx interrupts), a PCI host bus
callback is required. The patch for that is coming next.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alexander Graf <agraf@suse.de>
This implements H_XIRR_X hypercall in addition to H_XIRR as
it is mandatory for PAPR+ and there is no way for the guest to
detect whether it is supported or not so just add it.
As the Partition Adjunct Option is not supported at the moment,
the CPPR parameter of the hypercall is ignored.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alexander Graf <agraf@suse.de>
This adds support for the H_IPOLL hypercall which the guest
uses to poll for a pending interrupt. This hypercall is
mandatory for PAPR+ and there is no way for the guest to
detect whether it is supported or not so just add it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Recent (host) kernels support emulating the PAPR defined "XICS" interrupt
controller system within KVM. This patch allows qemu to initialize and
configure the in-kernel XICS, and keep its state in sync with qemu's XICS
state as necessary.
This should give considerable performance improvements. e.g. on a simple
IPI ping-pong test between hardware threads, using qemu XICS gives us
around 5,000 irqs/second, whereas the in-kernel XICS gives us around
70,000 irqs/s on the same hardware configuration.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
[Mike Qiu <qiudayu@linux.vnet.ibm.com>: fixed mistype which caused ics_set_kvm_state() to fail]
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
This adds a cpu_setup callback to the XICS device class (as XICS-KVM
will do it different), xics_cpu_setup() will call it if it is set.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alexander Graf <agraf@suse.de>
The upcoming XICS-KVM support will use bits of emulated XICS code.
So this introduces new level of hierarchy - "xics-common" class. Both
emulated XICS and XICS-KVM will inherit from it and override class
callbacks when required.
The new "xics-common" class implements:
1. replaces static "nr_irqs" and "nr_servers" properties with
the dynamic ones and adds callbacks to be executed when properties
are set.
2. xics_cpu_setup() callback renamed to xics_common_cpu_setup() as
it is a common part for both XICS'es
3. xics_reset() renamed to xics_common_reset() for the same reason.
The emulated XICS changes:
1. the part of xics_realize() which creates ICPs is moved to
the "nr_servers" property callback as realize() is too late to
create/initialize devices and instance_init() is too early to create
devices as the number of child devices comes via the "nr_servers"
property.
2. added ics_initfn() which does a little part of what xics_realize() did.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
This adds missing const specifiers to ICS and ICP TypeInfo's.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
This fixes XICS according new QOM rules.
This converts ICS's init() callbacks to realize().
This converts legacy qdev_init_nofail() to property_set(realized).
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The upcoming support of in-kernel XICS will redefine migration callbacks
for both ICS and ICP so classes and callback pointers are added.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alexander Graf <agraf@suse.de>
This replaces old-style fprintf with new style error_report.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
This simple change makes following patches nicer.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
* Fix QOM and ISA documentation errors
* Extend object_initialize() et al. to check the instance size
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=LiUs
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'afaerber/tags/qom-devices-for-anthony' into staging
QOM device refactorings
* Fix QOM and ISA documentation errors
* Extend object_initialize() et al. to check the instance size
# gpg: Signature made Fri 30 Aug 2013 02:19:48 PM CDT using RSA key ID 3E7E013F
# gpg: Can't check signature: public key not found
# By Andreas Färber (14) and others
# Via Andreas Färber
* afaerber/tags/qom-devices-for-anthony:
isa: Fix documentation of isa_register_portio_list()
qom: Assert instance size in object_initialize_with_type()
qom: Pass available size to object_initialize()
qdev: Pass size to qbus_create_inplace()
virtio-mmio: Pass size to virtio_mmio_bus_new()
virtio-ccw: Pass size to virtio_ccw_bus_new()
s390-virtio-bus: Pass size to virtio_s390_bus_new()
virtio-pci: Pass size to virtio_pci_bus_new()
usb: Pass size to usb_bus_new()
scsi: Pass size to scsi_bus_new()
pci: Pass size to pci_bus_new_inplace()
ide: Pass size to ide_bus_new()
ipack: Pass size to ipack_bus_new_inplace()
intel-hda: Pass size to hda_codec_bus_init()
qom: Fix object_initialize_with_type() argument name in documentation
virtio: Remove unnecessary OBJECT() casts
object: Fix typo in qom/object.h
Registration of global state belongs into realize so move it there.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
To be passed on to object_initialize_with_type().
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com> (virtio-ccw)
Signed-off-by: Andreas Färber <afaerber@suse.de>
This is an autogenerated patch using scripts/switch-timer-api.
Switch the entire code base to using the new timer API.
Note this patch may introduce some line length issues.
Signed-off-by: Alex Bligh <alex@alex.org.uk>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Create a new abstract base type and let omap-intc and omap2-intc inherit
from it. Introduce a type constant and use QOM casts.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Introduce type constant, use QOM casts and prepare SysBus initfn for QOM
realize by resolving SysBusDevice vs. DeviceState "dev" name conflict.
Acked-by: Peter Chubb <peter.chubb@nicta.com.au>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Basically, in HW the layout of the interrupt network is:
- One ICP per processor thread (the "presenter"). This contains the
registers to fetch a pending interrupt (ack), EOI, and control the
processor priority.
- One ICS per logical source of interrupts (ie, one per PCI host
bridge, and a few others here or there). This contains the per-interrupt
source configuration (target processor(s), priority, mask) and the
per-interrupt internal state.
Under PAPR, there is a single "virtual" ICS ... somewhat (it's a bit
oddball what pHyp does here, arguably there are two but we can ignore
that distinction). There is no register level access. A pair of firmware
(RTAS) calls is used to configure each virtual interrupt.
So our model here is somewhat the same. We have one ICS in the emulated
XICS which arguably *is* the emulated XICS, there's no point making it a
separate "device", that would just be gross, and each VCPU has an
associated ICP.
Yet we call the "XICS" struct icp_state and then the ICPs
'struct icp_server_state'. It's particularly confusing when all of the
functions have xics_prefixes yet take *icp arguments.
Rename:
struct icp_state -> XICSState
struct icp_server_state -> ICPState
struct ics_state -> ICSState
struct ics_irq_state -> ICSIRQState
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Message-id: 1374175984-8930-12-git-send-email-aliguori@us.ibm.com
[aik: added ics_resend() on post_load]
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Since current_cpu is CPUState it no longer depends on CPUPPCState.
Move ppce500_set_mpic_proxy() to a new hw/ppc/ppc_e500.h because
hw/ppc/ppc.h is too heavily using CPUPPCState and PowerPCCPU.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Move next_cpu from CPU_COMMON to CPUState.
Move first_cpu variable to qom/cpu.h.
gdbstub needs to use CPUState::env_ptr for now.
cpu_copy() no longer needs to save and restore cpu_next.
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
[AF: Rebased, simplified cpu_copy()]
Signed-off-by: Andreas Färber <afaerber@suse.de>
Split qdev initfn into instance_init and realize functions.
Change one occurrence of "klass" while at it.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Introduce type constant and cast macro.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Enables support for the in-kernel MPIC that thas been merged into the
KVM next branch. This includes irqfd/KVM_IRQ_LINE support from Alex
Graf (along with some other improvements).
Note from Alex regarding kvm_irqchip_create():
On x86, one would call kvm_irqchip_create() to initialize an
in-kernel interrupt controller. That function then goes ahead and
initializes global capability variables as well as the default irq
routing table.
On ppc, we can't call kvm_irqchip_create() because we can have
different types of interrupt controllers. So we want to do all the
things that function would do for us in the in-kernel device init
handler.
Signed-off-by: Scott Wood <scottwood@freescale.com>
[agraf: squash in kvm_irqchip_commit_routes patch, fix non-kvm build,
fix ppcemb]
Signed-off-by: Alexander Graf <agraf@suse.de>
This is a little strange. It is lowering the parent IRQ pin on input
when HIE is cleared. There is no such behaviour in the real hardware.
ISR changes based on interrupt pin state are already guarded on HIE
being set. So we can just delete this if in its entirety.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
When the Hardware Interrupt Enable (HIE) bit is set, software cannot
change ISR. Add write guard accordingly.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Acking a level sensitive interrupt should have no effect if the
interrupt pin is still asserted. The current implementation requires
and edge condition to occur for setting a level sensitive IRQ, which
means an ACK can clear a level sensitive interrupt, until the original
source strobes the interrupt again.
Fix by keeping track of the interrupt pin state and setting ISR based
on this every time update_irq() is called.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
For level sensitive interrupts, ISR bits are cleared when the input pin
is lowered. This is incorrect. Only software can clear ISR bits (via
IAR or direct write to ISR with !MER(2)).
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
* 'realize-isa.v2' of git://github.com/afaerber/qemu-cpu:
qdev: Drop FROM_QBUS() macro
isa: QOM'ify ISADevice
isa: QOM'ify ISABus
i8259: Convert PICCommonState to use QOM realizefn
kvm/i8259: QOM'ify some more
i8259: QOM'ify some more
i8254: Convert PITCommonState to QOM realizefn
kvm/i8254: QOM'ify some more
i8254: QOM'ify some more
isa: Use realizefn for ISADevice
cs4231a: QOM'ify some more
gus: QOM'ify some more
Use qemu_set_irq rather than if-elsing qemu_irq_(lower|raise). No
functional change, just reduces verbosity.
Cc: qemu-trivial@nongnu.org
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Instead of having the parent provide PICCommonClass::init,
let the children override DeviceClass::realize themselves.
This pushes the responsibility of saving and calling the parent's
realizefn to the children.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Drop ISADeviceClass::init and the resulting no-op initfn and let
children implement their own realizefn. Adapt error handling.
Split off an instance_init where sensible.
Signed-off-by: Andreas Färber <afaerber@suse.de>
apic has its own version of bitops, with the
difference that it works on u32 and not long.
Add apic_ prefix to avoid namespace clashes.
We should look into reusing standard bitops long-term,
but that's not entirely trivial.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Sun4c and Sun4d architectures and related CPUs are not fully implemented
(especially Sun4c MMU) and there has been no interest for them.
Likewise, a few CPUs (Cypress, Ross etc) are only half implemented.
Remove the machines and CPUs, they can be re-added if needed later.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
It allows APIC to be hotplugged.
* map APIC's mmio at board level if it is present
* do not register mmio region for each APIC, since
only one is used/mapped
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Put APIC_SPACE_SIZE in a public header so that it can be
reused elsewhere later.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Eliminate DO_UPCAST() for PICCommonState. Prepares for ISA realizefn.
Also give the i8259_common type registration functions unique names
while at it.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Message-id: 1367093935-29091-6-git-send-email-afaerber@suse.de
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The recent rearrangement of include files had some minor errors:
devices.h is not ARM specific and should not be in arm/
arm.h should be in arm/
Move these two headers to correct this.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Minor fixes to documentation and code comments.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Paolo Bonzini
Pavel Dovgalyuk
Alexander Graf
KONRAD Frederic
Peter Maydell
Gonglei
Sergey Fedorov
Adam Lackorzynski
Peter Crosthwaite
Jan Kiszka
Alexey Kardashevskiy
Oran Avraham
Paul Janzen
Juan Quintela
Cornelia Huck
Guenter Roeck
Gabriel L. Somlo
Hervé Poussineau
Michael Roth
Markus Armbruster
Rabin Vincent
Stefan Weil
Beniamino Galvani
Frank Ch. Eigler
Prasad Joshi
Dominik Dingel
Jens Freimann
Christoffer Dall
Edgar E. Iglesias
Anthony Liguori
xiaoqiang zhao
liguang
Andreas Färber
Benjamin Herrenschmidt
David Gibson
Anthony Liguori
Alex Bligh
Anthony Liguori
Hu Tao
Scott Wood
Blue Swirl
Michael S. Tsirkin
Dong Xu Wang
Igor Mammedov