This is needed for a quirk of the Raspberry Pi (bcm2835/6) MMC
controller, where the card insert bit is documented as unimplemented
(always reads zero, doesn't generate interrupts) but is in fact
observed on hardware as set at power on, but is cleared (and remains
clear) on subsequent controller resets.
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: 1450738069-18664-4-git-send-email-Andrew.Baumann@microsoft.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This deletes a block of code that raised a command index error if a
command returned response data, but the guest did not set the
appropriate bits in the response register to handle such a response. I
cannot find any documentation that suggests the controller should
behave in this way, the error code doesn't make sense (command index
error is defined for the case where the index in a response does not
match that of the issued command), and in at least one case (CMD23
issued by UEFI on Raspberry Pi 2), actual hardware does not do this.
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: 1450738069-18664-3-git-send-email-Andrew.Baumann@microsoft.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This check was conditionalising SD card operation on the card being
powered by the SDHCI host controller. It is however possible
(particularly in embedded systems) for the power control of the SD card
to be managed outside of SDHCI. This can be as trivial as hard-wiring
the SD slot VCC to a constant power-rail.
This means the guest SDHCI can validly opt-out of the SDHCI power
control feature while still using the card. So delete this check to
allow operation of the card with SDHCI power control.
This is needed for at least Xilinx Zynq and Raspberry Pi, and
also makes Freescale i.MX25 work for me. The digilent Zybo board
has a public schematic which shows SD VCC hardwiring:
http://digilentinc.com/Data/Products/ZYBO/ZYBO_sch_VB.3.pdf
bottom of page 3.
Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Reviewed-by: Sai Pavan Boddu <saipava@xilinx.com>
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Message-id: 1450738069-18664-2-git-send-email-Andrew.Baumann@microsoft.com
[AB: Add Pi to list of devices fixed in commit message]
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
blk_attach_dev() fails here only when we're working for device
"sdhci-pci" (which already attached the backend), and then we don't
want to attach a second time. If we ever create another failure mode,
we're setting up ourselves to using the same backend from multiple
frontends, which is likely to end in tears. Can't clean this up this
close to the release, so mark it FIXME.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1449503710-3707-3-git-send-email-armbru@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We currently fuse controller and card into a single device model, but
we intend qomify things properly and separate the two. The properties
that really belong to the card would then have to somehow pass-through
to the card's properties. To avoid that complication, either mark
them experimental or drop them.
Properties "capareg", "maxcurr" and the usual PCI device properties
belong to the controller. Property "drive" belongs to the card;
rename it to "x-drive". Properties "logical_block_size",
"physical_block_size", "min_io_size", "opt_io_size",
"discard_granularity" belong to the card, but have no effect; drop
them.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1449503710-3707-2-git-send-email-armbru@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Split sdhci.h into pubilc version (i.e include/hw/sd/sdhci.h) and
internal version (i.e hw/sd/sdhci-interna.h) based on register
declarations and object declaration.
Signed-off-by: Sai Pavan Boddu <saipava@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Create a sd directory under include/hw/ and move sd.h to
include/hw/sd/
Signed-off-by: Sai Pavan Boddu <saipava@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
It is possible for the guest to set an invalid block
size which is larger then the fifo_buffer[] array. This
could cause a buffer overflow.
To avoid this limit the maximum size of the blksize variable.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reported-by: Intel Security ATR <secure@intel.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: abe4c51f513290bbb85d1ee271cb1a3d463d7561.1444067470.git.alistair.francis@xilinx.com
Suggested-by: Igor Mitsyanko <i.mitsyanko@gmail.com>
Reported-by: Intel Security ATR <secure@intel.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Commit 19109131 disabled the sdhci-pci support because it used
drive_get_next(). This patch reenables sdhci-pci and changes it to
pass the drive via a qdev property - for example:
-device sdhci-pci,drive=drive0 -drive id=drive0,if=sd,file=myimage
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Conditional compilation hides few type mismatch warnings, fix it to
compile unconditionally.
Signed-off-by: Sai Pavan Boddu <saipava@xilinx.com>
Suggested-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Fix compile time warnings, because of type mismatch for unsigned long
long type.
Signed-off-by: Sai Pavan Boddu <saipava@xilinx.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
My Coccinelle semantic patch finds a few more, because it also fixes up
the equally pointless conditional
if (foo) {
free(foo);
foo = NULL;
}
Result (feel free to squash it into your patch):
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The free() and g_free() functions both happily accept
NULL on any platform QEMU builds on. As such putting a
conditional 'if (foo)' check before calls to 'free(foo)'
merely serves to bloat the lines of code.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Update the pxa2xx_mmci device to stop using the old_mmio read
and write callbacks in its MemoryRegionOps. This actually
simplifies the code because the separate byte/halfword/word
access functions were all calling into a single function to
do the work anyway.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: 1434117989-7367-6-git-send-email-peter.maydell@linaro.org
The only valid BlockBackend to pass to sd_reset() is the one for
the SD card, which is sd->blk. Drop the second argument from this
function in favour of having it just use sd->blk.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-id: 1430683444-9797-1-git-send-email-peter.maydell@linaro.org
ffs() cannot be replaced with ctz32() when the argument might be zero,
because ffs(0) returns 0 while ctz32(0) returns 32.
The ffs(3) call in sd_normal_command() is a special case though. It can
be converted to ctz32() + 1 because the argument is never zero:
if (!(req.arg >> 8) || (req.arg >> (ctz32(req.arg & ~0xff) + 1))) {
~~~~~~~~~~~~~~~
^--------------- req.arg cannot be zero
Cc: Markus Armbruster <armbru@redhat.com>
Cc: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1427124571-28598-7-git-send-email-stefanha@redhat.com
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Device models aren't supposed to go on fishing expeditions for
backends. They should expose suitable properties for the user to set.
For onboard devices, board code sets them.
A number of sysbus devices pick up block backends in their init() /
instance_init() methods with drive_get_next() instead: sl-nand,
milkymist-memcard, pl181, generic-sdhci.
Likewise, a number of sysbus devices pick up character backends in
their init() / realize() methods with qemu_char_get_next_serial():
cadence_uart, digic-uart, etraxfs,serial, lm32-juart, lm32-uart,
milkymist-uart, pl011, stm32f2xx-usart, xlnx.xps-uartlite.
All these mistakes are already marked FIXME. See the commit that
added these FIXMEs for a more detailed explanation of what's wrong.
Fortunately, only machines ppce500 and pseries-* support -device with
sysbus devices, and none of the devices above is supported with these
machines.
Set cannot_instantiate_with_device_add_yet to preserve our luck.
Cc: Andrzej Zaborowski <balrogg@gmail.com>
Cc: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Cc: Antony Pavlov <antonynpavlov@gmail.com>
Cc: "Edgar E. Iglesias" <edgar.iglesias@gmail.com>
Cc: Michael Walle <michael@walle.cc>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Device models aren't supposed to go on fishing expeditions for
backends. They should expose suitable properties for the user to set.
For onboard devices, board code sets them.
"sdhci-pci" picks up its block backend in its realize() method with
drive_get_next() instead. Already marked FIXME. See the commit that
added the FIXME for a more detailed explanation of what's wrong.
We can't fix this in time for the release, but since the device is new
in 2.3, we can set cannot_instantiate_with_device_add_yet to disable
it before this mistake becomes ABI, and we have to support command
lines like
$ qemu -drive if=sd -drive if=sd,file=sd.img -device sdhci-pci -device sdhci-pci
forever.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Drives defined with if!=none are for board initialization to wire up.
Board code calls drive_get() or similar to find them, and creates
devices with their qdev drive properties set accordingly.
Except a few devices go on a fishing expedition for a suitable backend
instead of exposing a drive property for board code to set: they call
driver_get() or drive_get_next() in their realize() or init() method
to implicitly connect to the "next" backend with a certain interface
type.
Picking up backends that way works when the devices are created by
board code. But it's inappropriate for -device or device_add. Not
only is this inconsistent with how the other block device models work
(they connect to a backend explicitly identified by a "drive"
property), it breaks when the "next" backend has been picked up by the
board already.
Example:
$ qemu-system-arm -S -M connex -pflash flash.img -device ssi-sd
Aborted (core dumped)
Mark them with suitable FIXME comments.
Cc: Andrzej Zaborowski <balrogg@gmail.com>
Cc: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Cc: "Andreas Färber" <andreas.faerber@web.de>
Cc: Michael Walle <michael@walle.cc>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Convert the device models where initialization obviously can't fail.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Gonglei <arei.gonglei@huawei.com>
Support for PCI devices following the "SD Host Controller Simplified
Specification Version 2.00" spec.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Update the sdhci sysbus QOM types and methods so that sysbus is in
their name. This is in preparation for adding PCI versions of these
types and methods.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The SDHCIClass defines a series of class "methods". However, no code
in the QEMU tree overrides these methods or even uses them outside of
sdhci.c.
Remove the virtual methods and replace them with direct calls to the
underlying functions. This simplifies the process of extending the
sdhci code to support PCI devices (which have a different parent
class).
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The Linux SDHCI PCI driver will only register the device if there is a
clock frequency set. So, set a default frequency of 52Mhz.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Device models should access their block backends only through the
block-backend.h API. Convert them, and drop direct includes of
inappropriate headers.
Just four uses of BlockDriverState are left:
* The Xen paravirtual block device backend (xen_disk.c) opens images
itself when set up via xenbus, bypassing blockdev.c. I figure it
should go through qmp_blockdev_add() instead.
* Device model "usb-storage" prompts for keys. No other device model
does, and this one probably shouldn't do it, either.
* ide_issue_trim_cb() uses bdrv_aio_discard() instead of
blk_aio_discard() because it fishes its backend out of a BlockAIOCB,
which has only the BlockDriverState.
* PC87312State has an unused BlockDriverState[] member.
The next two commits take care of the latter two.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The patch is big, but all it really does is replacing
dinfo->bdrv
by
blk_bs(blk_by_legacy_dinfo(dinfo))
The replacement is repetitive, but the conversion of device models to
BlockBackend is imminent, and will shorten it to just
blk_legacy_dinfo(dinfo).
Line wrapping muddies the waters a bit. I also omit tests whether
dinfo->bdrv is null, because it never is.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Benoît Canet <benoit.canet@nodalink.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This dma_memory_read was giving too big a size when begin was non-zero.
This could cause segfaults in some circumstances. Fix.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Replace qemu_allocate_irqs(foo, bar, 1)[0]
with qemu_allocate_irq(foo, bar, 0).
This avoids leaking the dereferenced qemu_irq *.
Cc: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
[PC Changes:
* Applied change to instance in sh4/sh7750.c
]
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Kirill Batuzov <batuzovk@ispras.ru>
[AF: Fix IRQ index in sh4/sh7750.c]
Cc: qemu-stable@nongnu.org
Signed-off-by: Andreas Färber <afaerber@suse.de>
It does a g_free() on the pointer, so don't pass a local &foo reference.
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Cc: qemu-stable@nongnu.org
Signed-off-by: Andreas Färber <afaerber@suse.de>
Drop the sd_acmd_type[] array: it is never used. (The equivalent
sd_cmd_type[] array for normal commands is used to identify
those commands whose argument includes the card address in the
top 16 bits; but for app commands the card address is passed
with the APP_CMD prefix, not with the argument to the app command
itself.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
After previous Peter patch, they are redundant. This way we don't
assign them except when needed. Once there, there were lots of case
where the ".fields" indentation was wrong:
.fields = (VMStateField []) {
and
.fields = (VMStateField []) {
Change all the combinations to:
.fields = (VMStateField[]){
The biggest problem (appart from aesthetics) was that checkpatch complained
when we copy&pasted the code from one place to another.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
CVE-2013-4537
s->arglen is taken from wire and used as idx
in ssi_sd_transfer().
Validate it before access.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Convert legacy ->qdev style casts from TYPE_SSI_SLAVE to TYPE_DEVICE.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
[AF: Introduce local DeviceState variable for transition to QOM realize]
Signed-off-by: Andreas Färber <afaerber@suse.de>
* QTest cleanups and test cases for PCI NICs
* NAND fix for "info qtree"
* Cleanup and extension of QOM machine tests
* IndustryPack test cases and conversion to QOM realize
* I2C cleanups
* Cleanups of legacy qdev properties
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=KRcc
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/afaerber/tags/qom-devices-for-peter' into staging
QOM infrastructure fixes and device conversions
* QTest cleanups and test cases for PCI NICs
* NAND fix for "info qtree"
* Cleanup and extension of QOM machine tests
* IndustryPack test cases and conversion to QOM realize
* I2C cleanups
* Cleanups of legacy qdev properties
# gpg: Signature made Mon 17 Feb 2014 22:15:37 GMT using RSA key ID 3E7E013F
# gpg: Good signature from "Andreas Färber <afaerber@suse.de>"
# gpg: aka "Andreas Färber <afaerber@suse.com>"
* remotes/afaerber/tags/qom-devices-for-peter: (49 commits)
qtest: Include system headers before user headers
qapi: Refine human printing of sizes
qdev: Use QAPI type names for properties
qdev: Add enum property types to QAPI schema
block: Handle "rechs" and "large" translation options
qdev: Remove hex8/32/64 property types
qdev: Remove most legacy printers
qdev: Use human mode in "info qtree"
qapi: Add human mode to StringOutputVisitor
qdev: Inline qdev_prop_parse()
qdev: Legacy properties are just strings
qdev: Legacy properties are now read-only
qdev: Remove legacy parsers for hex8/32/64
qdev: Sizes are now parsed by StringInputVisitor
qapi: Add size parser to StringInputVisitor
qtest: Don't segfault with invalid -qtest option
ipack: Move IndustryPack out of hw/char/
ipoctal232: QOM parent field cleanup
ipack: QOM parent field cleanup for IPackDevice
ipack: QOM parent field cleanup for IPackBus
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Replace them with uint8/32/64.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
device_add plugs devices into suitable bus. For "real" buses, that
actually connects the device. For sysbus, the connections need to be
made separately, and device_add can't do that. The device would be
left unconnected, and could not possibly work.
Quite a few, but not all sysbus devices already set
cannot_instantiate_with_device_add_yet in their class init function.
Set it in their abstract base's class init function
sysbus_device_class_init(), and remove the now redundant assignments
from device class init functions.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel.a@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
In an ideal world, machines can be built by wiring devices together
with configuration, not code. Unfortunately, that's not the world we
live in right now. We still have quite a few devices that need to be
wired up by code. If you try to device_add such a device, it'll fail
in sometimes mysterious ways. If you're lucky, you get an
unmysterious immediate crash.
To protect users from such badness, DeviceClass member no_user used to
make device models unavailable with -device / device_add, but that
regressed in commit 18b6dad. The device model is still omitted from
help, but is available anyway.
Attempts to fix the regression have been rejected with the argument
that the purpose of no_user isn't clear, and it's prone to misuse.
This commit clarifies no_user's purpose. Anthony suggested to rename
it cannot_instantiate_with_device_add_yet_due_to_internal_bugs, which
I shorten somewhat to keep checkpatch happy. While there, make it
bool.
Every use of cannot_instantiate_with_device_add_yet gets a FIXME
comment asking for rationale. The next few commits will clean them
all up, either by providing a rationale, or by getting rid of the use.
With that done, the regression fix is hopefully acceptable.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel.a@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Commit 4f8a066b5f (blockdev: Remove IF_*
check for read-only blockdev_init) added a usage of bdrv_is_read_only()
to sd_init(), which is called for versatilepb, versatileab and
xilinx-zynq-a9 machines among others with NULL argument by default,
causing the new qom-test to fail.
Add a check to prevent this.
Suggested-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
IF_NONE allows read-only, which makes forbidding it in this place
for other types pretty much pointless.
Instead, make sure that all devices for which the check would have
errored out check in their init function that they don't get a read-only
BlockDriverState. This catches even cases where IF_NONE and -device is
used.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
This is an autogenerated patch using scripts/switch-timer-api.
Switch the entire code base to using the new timer API.
Note this patch may introduce some line length issues.
Signed-off-by: Alex Bligh <alex@alex.org.uk>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Add a cast to avoid potentially shifting into the sign bit of
a signed value, which is undefined behaviour in C.
(Detected with clang's -fsanitize=undefined.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1372341831-4264-1-git-send-email-peter.maydell@linaro.org
