Callers must pass ELF machine, byte swapping and symbol LSB clearing
information to ELF loader. A.out loader needs page size information, pass
that too as a parameter.
Extract prototypes to a separate file. Move loader.[ch] and elf_ops.h under hw.
Adjust callers. Also use target_phys_addr_t instead of target_ulong for
addresses: loader addresses aren't virtual.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Sorry folks, but it has to be. One more of these invasive qdev patches.
We have a serious design bug in the qdev interface: device init
callbacks can't signal failure because the init() callback has no
return value. This patch fixes it.
We have already one case in-tree where this is needed:
Try -device virtio-blk-pci (without drive= specified) and watch qemu
segfault. This patch fixes it.
With usb+scsi being converted to qdev we'll get more devices where the
init callback can fail for various reasons.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Level 15 interrupts are broadcast to all CPUs, each CPU can clear the
interrupt using the local Clear Pending register.
Update intbit_to_level table.
Don't try to raise level 0 interrupts.
Calculate pending interrupts based on the separate inputs from master
register. Setting or resetting the pending level isn't correct because of
overlap of levels.
Level 14 is always used for CPU timer interrupts, remove the property.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
First step cleaning up the drives handling. This one does nothing but
removing drives_table[], still it became seriously big.
drive_get_index() is gone and is replaced by drives_get() which hands
out DriveInfo pointers instead of a table index. This needs adaption in
*tons* of places all over.
The drives are now maintained as linked list.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This patch is a major overhaul of the device properties. The properties
are saved directly in the device state struct now, the linked list of
property values is gone.
Advantages:
* We don't have to maintain the list with the property values.
* The value in the property list and the value actually used by
the device can't go out of sync any more (used to happen for
the pci.devfn == -1 case) because there is only one place where
the value is stored.
* A record describing the property is required now, you can't set
random properties any more.
There are bus-specific and device-specific properties. The former
should be used for properties common to all bus drivers. Typical
use case is bus addressing, i.e. pci.devfn and i2c.address.
Properties have a PropertyInfo struct attached with name, size and
function pointers to parse and print properties. A few common property
types have PropertyInfos defined in qdev-properties.c. Drivers are free
to implement their own very special property parsers if needed.
Properties can have default values. If unset they are zero-filled.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This reverts commit 8217606e6e (and
updates later added users of qemu_register_reset), we solved the
problem it originally addressed less invasively.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
We have both IRQ sinks and GPIO inputs. These are in principle exactly
the same thing, so remove the former.
Signed-off-by: Paul Brook <paul@codesourcery.com>
Add the parameter 'order' to qemu_register_reset and sort callbacks on
registration. On system reset, callbacks with lower order will be
invoked before those with higher order. Update all existing users to the
standard order 0.
Note: At least for x86, the existing users seem to assume that handlers
are called in their registration order. Therefore, the patch preserves
this property. If someone feels bored, (s)he could try to identify this
dependency and express it properly on callback registration.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
f80f9ec changed the order that machines are registered which had the effect of
changing the default machine. This changeset introduces a new is_default field
so that machine types can declare that they are the default for an architecture.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
My previous commit, f92f8afebe, broke -vnc (spotted by Glauber Costa). This
is because it's necessary to tell when the no special display parameters have
been passed and default to SDL or VNC appropriately.
This refactors the display selection logic to be less complicated which has
the effect of fixing the regression mentioned above.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The vga_ram_size argument to machine init functions always has the same
value, and is ignored by many machines (including SPARC32 which has an
obsolete ifdef for VGA_RAM_SIZE).
Remove it and push VGA_RAM_SIZE into vga_int.h.
Signed-off-by: Paul Brook <paul@codesourcery.com>
All archs have some kind of firmware to load and can be fine with it
already. So there is not much use in enforcing the presence of a disk.
If the system setup requires one, the user will notice it anyway once
the firmware/bios fails to boot from it.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@6899 c046a42c-6fe2-441c-8c8c-71466251a162
Use firmware configuration device for boot device, kernel, initrd and
kernel command line parameters on PPC, Sparc32 and Sparc64.
Update OpenBIOS images to r479 which supports the change.
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@6777 c046a42c-6fe2-441c-8c8c-71466251a162
Refactor the monitor API and prepare it for decoupled terminals:
term_print functions are renamed to monitor_* and all monitor services
gain a new parameter (mon) that will once refer to the monitor instance
the output is supposed to appear on. However, the argument remains
unused for now. All monitor command callbacks are also extended by a mon
parameter so that command handlers are able to pass an appropriate
reference to monitor output services.
For the case that monitor outputs so far happen without clearly
identifiable context, the global variable cur_mon is introduced that
shall once provide a pointer either to the current active monitor (while
processing commands) or to the default one. On the mid or long term,
those use case will be obsoleted so that this variable can be removed
again.
Due to the broad usage of the monitor interface, this patch mostly deals
with converting users of the monitor API. A few of them are already
extended to pass 'mon' from the command handler further down to internal
functions that invoke monitor_printf.
At this chance, monitor-related prototypes are moved from console.h to
a new monitor.h. The same is done for the readline API.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@6711 c046a42c-6fe2-441c-8c8c-71466251a162
Patch 5/7
This patch changes the graphical_console_init function to return an
allocated DisplayState instead of a QEMUConsole.
This patch contains just the graphical_console_init change and few other
modifications mainly in console.c and vl.c.
It was necessary to move the display frontends (e.g. sdl and vnc)
initialization after machine->init in vl.c.
This patch does *not* include any required changes to any device, these
changes come with the following patches.
Patch 6/7
This patch changes the QEMUMachine init functions not to take a
DisplayState as an argument because is not needed any more;
In few places the graphic hardware initialization function was called
only if DisplayState was not NULL, now they are always called.
Apart from these cases, the rest are all mechanical substitutions.
Patch 7/7
This patch updates the graphic device code to use the new
graphical_console_init function.
As for the previous patch, in few places graphical_console_init was called
only if DisplayState was not NULL, now it is always called.
Apart from these cases, the rest are all mechanical substitutions.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@6344 c046a42c-6fe2-441c-8c8c-71466251a162
The Z85C30 on the PowerMAC machines have one interrupt per serial
channel, while the Sparc machines have only one for both. Allow the
emulated device to use one IRQ per channel.
Patch by Laurent Vivier.
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@6295 c046a42c-6fe2-441c-8c8c-71466251a162
Some NIC init functions are only called when that model is
the only valid model. In that case, it makes sense to use
qemu_check_nic_model() from the NIC init function itself.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@6286 c046a42c-6fe2-441c-8c8c-71466251a162
Swap the two CharDriverState arguments so that the first argument
corresponds to the channel A and the second argument to the channel B.
Modify hw/sun4m.c accordingly.
This fixes the order of the serial ports on the PPC machines.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@6284 c046a42c-6fe2-441c-8c8c-71466251a162
Blue Swirl
Gerd Hoffmann
Jan Kiszka
Paul Brook
Jan Kiszka
Anthony Liguori
pbrook
aliguori
blueswir1
aurel32