noload kernels are loaded with the u-boot image header and as a result
the header size needs adding to the entry point. Fake up a hdr so the
kernel image is loaded at the right address and the entry point is
adjusted appropriately.
The default location for the uboot file is 32MiB above bottom of DRAM.
This matches the recommendation in Documentation/arm/Booting.
Clarify the load_uimage API to state the passing of a load address when an
image doesn't specify one, or when loading a ramdisk is expected.
Adjust callers of load_uimage, etc.
Signed-off-by: Nick Hudson <skrll@netbsd.org>
Message-id: 11488a08-1fe0-a278-2210-deb64731107f@gmx.co.uk
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Architecturally, it's possible for an AArch64 machine to have
all of its RAM over the 4GB mark, but our kernel/initrd loading
code in boot.c assumes that the upper half of the addresses
to load these images to is always zero. Write the whole 64 bit
address into the bootloader code fragment, not just the low half.
Note that, currently, none of the existing QEMU machines have
their main memory over 4GBs, so this was not a user-visible bug.
Signed-off-by: Ricardo Perez Blanco <ricardo.perez_blanco@nokia.com>
[PMM: revised commit message and tweaked some long lines]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
"The Image must be placed text_offset bytes from a 2MB aligned base
address anywhere in usable system RAM and called there."
For the virt board, we write our startup bootloader at the very
bottom of RAM, so that bit can't be used for the image. To avoid
overlap in case the image requests to be loaded at an offset
smaller than our bootloader, we increment the load offset to the
next 2MB.
This fixes a boot failure for Xen AArch64.
Signed-off-by: Stewart Hildebrand <stewart.hildebrand@dornerworks.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Message-id: b8a89518794b4436af0c151ed10de4fa@dornerworks.com
[PMM: Rephrased a comment a bit]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The kernel booting specification for an AArch32 kernel requires that
it is booted in Hyp mode if available; otherwise the kernel can't
enable KVM. We were incorrectly leaving the kernel in SVC mode.
If we're booting an AArch32 kernel in the Nonsecure state and Hyp
mode is available, start in it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-id: 20180820153020.21478-7-peter.maydell@linaro.org
Use an int64_t as a return type to restore
the negative check for arm_load_as.
Signed-off-by: Adam Lackorzynski <adam@l4re.org>
Message-id: 20180730173712.GG4987@os.inf.tu-dresden.de
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When running dtc on the guest /proc/device-tree we get the
following warning: Warning (unit_address_vs_reg): Node /memory
has a reg or ranges property, but no unit name".
Let's fix that by adding the unit address to the node name. We also
don't create the /memory node anymore in create_fdt(). We directly
create it in load_dtb. /chosen still needs to be created in create_fdt
as the uart needs it. In case the user provided his own dtb, we nop
all memory nodes found in root and create new one(s).
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1530044492-24921-4-git-send-email-eric.auger@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When QEMU is started with following CLI
-machine virt,gic-version=3,accel=kvm -cpu host -bios AAVMF_CODE.fd
it crashes with abort at
accel/kvm/kvm-all.c:2164:
KVM_SET_DEVICE_ATTR failed: Group 6 attr 0x000000000000c665: Invalid argument
Which is caused by implicit dependency of kvm_arm_gicv3_reset() on
arm_gicv3_icc_reset() where the later is called by CPU reset
reset callback.
However commit:
3b77f6c arm/boot: split load_dtb() from arm_load_kernel()
broke CPU reset callback registration in case
arm_load_kernel()
...
if (!info->kernel_filename || info->firmware_loaded)
branch is taken, i.e. it's sufficient to provide a firmware
or do not provide kernel on CLI to skip cpu reset callback
registration, where before offending commit the callback
has been registered unconditionally.
Fix it by registering the callback right at the beginning of
arm_load_kernel() unconditionally instead of doing it at the end.
NOTE:
we probably should eliminate that dependency anyways as well as
separate arch CPU reset parts from arm_load_kernel() into CPU
itself, but that refactoring that I probably would have to do
anyways later for CPU hotplug to work.
Reported-by: Auger Eric <eric.auger@redhat.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1527070950-208350-1-git-send-email-imammedo@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
load_dtb() depends on arm_load_kernel() to figure out place
in RAM where it should be loaded, but it's not required for
arm_load_kernel() to work. Sometimes it's neccesary for
devices added with -device/device_add to be enumerated in
DTB as well, which's lead to [1] and surrounding commits to
add 2 more machine_done notifiers with non obvious ordering
to make dynamic sysbus devices initialization happen in
the right order.
However instead of moving whole arm_load_kernel() in to
machine_done, it's sufficient to move only load_dtb() into
virt_machine_done() notifier and remove ArmLoadKernelNotifier/
/PlatformBusFDTNotifierParams notifiers, which saves us ~90LOC
and simplifies code flow quite a bit.
Later would allow to consolidate DTB generation within one
function for 'mach-virt' board and make it reentrant so it
could generate updated DTB in device hotplug secenarios.
While at it rename load_dtb() to arm_load_dtb() since it's
public now.
Add additional field skip_dtb_autoload to struct arm_boot_info
to allow manual DTB load later in mach-virt and to avoid touching
all other boards to explicitly call arm_load_dtb().
1) (ac9d32e hw/arm/boot: arm_load_kernel implemented as a machine init done notifier)
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1525691524-32265-4-git-send-email-imammedo@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Even though nothing is currently broken (since all boards
use first_cpu as boot cpu), make sure that boot_info is set
on all CPUs.
If some board would like support heterogenuos setup (i.e.
init boot_info on subset of CPUs) in future, it should add
a reasonable API to do it, instead of starting assigning
boot_info from some CPU and till the end of present CPUs
list.
Ref:
"Message-ID: <CAFEAcA_NMWuA8WSs3cNeY6xX1kerO_uAcN_3=fK02BEhHJW86g@mail.gmail.com>"
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1525176522-200354-5-git-send-email-imammedo@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
if arm_load_kernel() were passed non first_cpu, QEMU would end up
with partially set do_cpu_reset() callback leaving some CPUs without it.
Make sure that do_cpu_reset() is registered for all CPUs by enumerating
CPUs from first_cpu.
(In practice every board that we have was passing us the first CPU
as the boot CPU, either directly or indirectly, so this wasn't
causing incorrect behaviour.)
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: added a note that this isn't a behaviour change]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Change the code to avoid exiting QEMU if user provided DTB contains
manually specified /psci node and skip any /psci related fixups
instead.
Fixes: 4cbca7d9b4 ("hw/arm: Move virt's PSCI DT fixup code to
arm/boot.c")
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reported-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Message-id: 20180402205654.14572-1-andrew.smirnov@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If we're directly booting a Linux kernel and the CPU supports both
EL3 and EL2, we start the kernel in EL2, as it expects. We must also
set the SCR_EL3.HCE bit in this situation, so that the HVC
instruction is enabled rather than UNDEFing. Otherwise at least some
kernels will panic when trying to initialize KVM in the guest.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180313153458.26822-4-peter.maydell@linaro.org
Add some assertions that if we're about to boot an AArch64 kernel,
the board code has not mistakenly set either secure_boot or
secure_board_setup. It doesn't make sense to set secure_boot,
because all AArch64 kernels must be booted in non-secure mode.
It might in theory make sense to set secure_board_setup, but
we don't currently support that, because only the AArch32
bootloader[] code calls this hook; bootloader_aarch64[] does not.
Since we don't have a current need for this functionality, just
assert that we don't try to use it. If it's needed we'll add
it later.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180313153458.26822-3-peter.maydell@linaro.org
Spotted by ASAN:
QTEST_QEMU_BINARY=aarch64-softmmu/qemu-system-aarch64 tests/boot-serial-test
Direct leak of 48 byte(s) in 1 object(s) allocated from:
#0 0x7ff8a9b0ca38 in __interceptor_calloc (/lib64/libasan.so.4+0xdea38)
#1 0x7ff8a8ea7f75 in g_malloc0 ../glib/gmem.c:124
#2 0x55fef3d99129 in error_setv /home/elmarco/src/qemu/util/error.c:59
#3 0x55fef3d99738 in error_setg_internal /home/elmarco/src/qemu/util/error.c:95
#4 0x55fef323acb2 in load_elf_hdr /home/elmarco/src/qemu/hw/core/loader.c:393
#5 0x55fef2d15776 in arm_load_elf /home/elmarco/src/qemu/hw/arm/boot.c:830
#6 0x55fef2d16d39 in arm_load_kernel_notify /home/elmarco/src/qemu/hw/arm/boot.c:1022
#7 0x55fef3dc634d in notifier_list_notify /home/elmarco/src/qemu/util/notify.c:40
#8 0x55fef2fc3182 in qemu_run_machine_init_done_notifiers /home/elmarco/src/qemu/vl.c:2716
#9 0x55fef2fcbbd1 in main /home/elmarco/src/qemu/vl.c:4679
#10 0x7ff89dfed009 in __libc_start_main (/lib64/libc.so.6+0x21009)
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Instead of loading kernels, device trees, and the like to
the system address space, use the CPU's address space. This
is important if we're trying to load the file to memory or
via an alias memory region that is provided by an SoC
object and thus not mapped into the system address space.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180220180325.29818-3-peter.maydell@linaro.org
-----BEGIN PGP SIGNATURE-----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=DMbf
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/armbru/tags/pull-misc-2018-02-07-v4' into staging
Miscellaneous patches for 2018-02-07
# gpg: Signature made Fri 09 Feb 2018 12:52:51 GMT
# gpg: using RSA key 3870B400EB918653
# gpg: Good signature from "Markus Armbruster <armbru@redhat.com>"
# gpg: aka "Markus Armbruster <armbru@pond.sub.org>"
# Primary key fingerprint: 354B C8B3 D7EB 2A6B 6867 4E5F 3870 B400 EB91 8653
* remotes/armbru/tags/pull-misc-2018-02-07-v4:
Move include qemu/option.h from qemu-common.h to actual users
Drop superfluous includes of qapi/qmp/qjson.h
Drop superfluous includes of qapi/qmp/dispatch.h
Include qapi/qmp/qnull.h exactly where needed
Include qapi/qmp/qnum.h exactly where needed
Include qapi/qmp/qbool.h exactly where needed
Include qapi/qmp/qstring.h exactly where needed
Include qapi/qmp/qdict.h exactly where needed
Include qapi/qmp/qlist.h exactly where needed
Include qapi/qmp/qobject.h exactly where needed
qdict qlist: Make most helper macros functions
Eliminate qapi/qmp/types.h
Typedef the subtypes of QObject in qemu/typedefs.h, too
Include qmp-commands.h exactly where needed
Drop superfluous includes of qapi/qmp/qerror.h
Include qapi/error.h exactly where needed
Drop superfluous includes of qapi-types.h and test-qapi-types.h
Clean up includes
Use #include "..." for our own headers, <...> for others
vnc: use stubs for CONFIG_VNC=n dummy functions
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
qemu-common.h includes qemu/option.h, but most places that include the
former don't actually need the latter. Drop the include, and add it
to the places that actually need it.
While there, drop superfluous includes of both headers, and
separate #include from file comment with a blank line.
This cleanup makes the number of objects depending on qemu/option.h
drop from 4545 (out of 4743) to 284 in my "build everything" tree.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180201111846.21846-20-armbru@redhat.com>
[Semantic conflict with commit bdd6a90a9e in block/nvme.c resolved]
Move virt's PSCI DT fixup code to arm/boot.c and set this fixup to
happen automatically for every board that doesn't mark "psci-conduit"
as disabled. This way emulated boards other than "virt" that rely on
PSIC for SMP could benefit from that code.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Philippe Mathieu-Daudé <f4bug@amsat.org>
Cc: Marcel Apfelbaum <marcel.apfelbaum@zoho.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: qemu-devel@nongnu.org
Cc: qemu-arm@nongnu.org
Cc: yurovsky@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Replace a large number of the fprintf(stderr, "*\n" calls with
error_report(). The functions were renamed with these commands and then
compiler issues where manually fixed.
find ./* -type f -exec sed -i \
'N;N;N;N;N;N;N;N;N;N;N;N; {s|fprintf(stderr, "\(.*\)\\n"\(.*\));|error_report("\1"\2);|Ig}' \
{} +
find ./* -type f -exec sed -i \
'N;N;N;N;N;N;N;N;N;N;N; {s|fprintf(stderr, "\(.*\)\\n"\(.*\));|error_report("\1"\2);|Ig}' \
{} +
find ./* -type f -exec sed -i \
'N;N;N;N;N;N;N;N;N; {s|fprintf(stderr, "\(.*\)\\n"\(.*\));|error_report("\1"\2);|Ig}' \
{} +
find ./* -type f -exec sed -i \
'N;N;N;N;N;N;N;N; {s|fprintf(stderr, "\(.*\)\\n"\(.*\));|error_report("\1"\2);|Ig}' \
{} +
find ./* -type f -exec sed -i \
'N;N;N;N;N;N;N; {s|fprintf(stderr, "\(.*\)\\n"\(.*\));|error_report("\1"\2);|Ig}' \
{} +
find ./* -type f -exec sed -i \
'N;N;N;N;N;N; {s|fprintf(stderr, "\(.*\)\\n"\(.*\));|error_report("\1"\2);|Ig}' \
{} +
find ./* -type f -exec sed -i \
'N;N;N;N;N; {s|fprintf(stderr, "\(.*\)\\n"\(.*\));|error_report("\1"\2);|Ig}' \
{} +
find ./* -type f -exec sed -i \
'N;N;N;N; {s|fprintf(stderr, "\(.*\)\\n"\(.*\));|error_report("\1"\2);|Ig}' \
{} +
find ./* -type f -exec sed -i \
'N;N;N; {s|fprintf(stderr, "\(.*\)\\n"\(.*\));|error_report("\1"\2);|Ig}' \
{} +
find ./* -type f -exec sed -i \
'N;N; {s|fprintf(stderr, "\(.*\)\\n"\(.*\));|error_report("\1"\2);|Ig}' \
{} +
find ./* -type f -exec sed -i \
'N; {s|fprintf(stderr, "\(.*\)\\n"\(.*\));|error_report("\1"\2);|Ig}' \
{} +
Some lines where then manually tweaked to pass checkpatch.
The 'qemu: ' prefix was manually removed from the hw/arm/boot.c file.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Cc: qemu-arm@nongnu.org
Conversions that aren't followed by exit() dropped, because they might
be inappropriate.
Also trim trailing punctuation from error messages.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180203084315.20497-3-armbru@redhat.com>
The arm64 boot protocol stipulates that the kernel must be loaded
TEXT_OFFSET bytes beyond a 2 MB aligned base address, where TEXT_OFFSET
could be any 4 KB multiple between 0 and 2 MB, and whose value can be
found in the header of the Image file.
So after attempts to load the arm64 kernel image as an ELF file or as a
U-Boot image have failed (both of which have their own way of specifying
the load offset), try to determine the TEXT_OFFSET from the image after
loading it but before mapping it as a ROM mapping into the guest address
space.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1489414630-21609-1-git-send-email-ard.biesheuvel@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
While customary, the /chosen and /memory devicetree nodes do not have to
exist. Create if necessary. Also create the /memory/device_type property
if needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 1479346221-18474-1-git-send-email-linux@roeck-us.net
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When kernel and device tree are specified in the QEMU commandline, then
this device tree may be modified e.g. to add virtio_mmio devices.
With a bootloader e.g. on a flash device these extra devices are not
available.
With this change, the device tree can be specified at the QEMU commandline.
The modified device tree made available to the bootloader with the same
mechanism already supported by device trees fully generated by QEMU.
Signed-off-by: Michael Olbrich <m.olbrich@pengutronix.de>
Message-id: 1473520054-402-1-git-send-email-m.olbrich@pengutronix.de
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Generate memory nodes according to NUMA topology. Set numa-node-id
property for cpu and memory nodes.
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1461667229-9216-2-git-send-email-zhaoshenglong@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The 32-bit ARM Linux kernel booting ABI requires that r0 is 0
when calling the kernel image. A bug in commit 10b8ec73e6
meant that for boards which use the write_board_setup hook (which
means "highbank", "midway", "raspi2" and "xilinx-zynq-a9") we
were incorrectly skipping the "clear r0" instruction in the
mini-bootloader. Use the right offset in the "add lr, pc, #n"
instruction so that we return from the board-setup code to the
correct place.
Signed-off-by: Sylvain Garrigues <sylvain@sylvaingarrigues.com>
[PMM: Expanded commit message]
Cc: qemu-stable@nongnu.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Commit 57cb38b included qapi/error.h into qemu/osdep.h to get the
Error typedef. Since then, we've moved to include qemu/osdep.h
everywhere. Its file comment explains: "To avoid getting into
possible circular include dependencies, this file should not include
any other QEMU headers, with the exceptions of config-host.h,
compiler.h, os-posix.h and os-win32.h, all of which are doing a
similar job to this file and are under similar constraints."
qapi/error.h doesn't do a similar job, and it doesn't adhere to
similar constraints: it includes qapi-types.h. That's in excess of
100KiB of crap most .c files don't actually need.
Add the typedef to qemu/typedefs.h, and include that instead of
qapi/error.h. Include qapi/error.h in .c files that need it and don't
get it now. Include qapi-types.h in qom/object.h for uint16List.
Update scripts/clean-includes accordingly. Update it further to match
reality: replace config.h by config-target.h, add sysemu/os-posix.h,
sysemu/os-win32.h. Update the list of includes in the qemu/osdep.h
comment quoted above similarly.
This reduces the number of objects depending on qapi/error.h from "all
of them" to less than a third. Unfortunately, the number depending on
qapi-types.h shrinks only a little. More work is needed for that one.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
[Fix compilation without the spice devel packages. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Support ARM big-endian ELF files in system-mode emulation. When loading
an elf, determine the endianness mode expected by the elf, and set the
relevant CPU state accordingly.
With this, big-endian modes are now fully supported via system-mode LE,
so there is no need to restrict the elf loading to the TARGET
endianness so the ifdeffery on TARGET_WORDS_BIGENDIAN goes away.
Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: fix typo in comments]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some CPUs are of an opposite data-endianness to other components in the
system. Sometimes elfs have the data sections layed out with this CPU
data-endianness accounting for when loaded via the CPU, so byte swaps
(relative to other system components) will occur.
The leading example, is ARM's BE32 mode, which is is basically LE with
address manipulation on half-word and byte accesses to access the
hw/byte reversed address. This means that word data is invariant
across LE and BE32. This also means that instructions are still LE.
The expectation is that the elf will be loaded via the CPU in this
endianness scheme, which means the data in the elf is reversed at
compile time.
As QEMU loads via the system memory directly, rather than the CPU, we
need a mechanism to reverse elf data endianness to implement this
possibility.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch aligns the prototype with qemu_fdt_getprop. The caller
can choose whether the function self-asserts on error (passing
&error_fatal as Error ** argument, corresponding to the legacy behavior),
or behaves differently such as simply output a message.
In this later case the caller can use the new lenp parameter to interpret
the error if any.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The new version is slightly different, to support Rasbperry Pi (in
particular, Pi1's arm11 core which doesn't support v7 instructions
such as MOVW).
Tested-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When booting Linux on AArch64 enabled cores, setup EL1 and
EL2 to use AArch64.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1449505425-32022-4-git-send-email-peter.maydell@linaro.org
Add a flag that when set, will cause the primary CPU to start in secure
mode, even if the overall boot is non-secure. This is useful for when
there is a board-setup blob that needs to run from secure mode, but
device and secondary CPU init should still be done as-normal for a non-
secure boot.
Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: d1170774d5446d715fced7739edfc61a5be931f9.1447007690.git.crosthwaite.peter@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add an API for boards to inject their own preboot software (or
firmware) sequence.
The software then returns to the bootloader via the link register. This
allows boards to do their own little bits of firmware setup without
needed to replace the bootloader completely (which is the requirement
for existing firmware support).
The blob is loaded by a callback if and only if doing a linux boot
(similar to the existing write_secondary support).
Rewrite the comment for the primary boot blob.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: 070295644c6ac84696d743913296e8cfefb48c15.1446182614.git.crosthwaite.peter@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
These comments start immediately after the current longest name in the
list. Tab them out to the next tab stop to give a little breathing room
and prepare for FIXUP_BOARD_SETUP which will require more indent.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: b9b9bb8f1c307c1ef8a3f26ff1f34fabb34b332e.1446182614.git.crosthwaite.peter@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
For ARM we have a little minimalist bootloader in hw/arm/boot.c which
takes the place of firmware if we're directly booting a Linux kernel.
Unfortunately a few devices need special case handling in this situation
to do the initialization which on real hardware would be done by
firmware. (In particular if we're booting a kernel in NonSecure state
then we need to make a TZ-aware GIC put all its interrupts into Group 1,
or the guest will be unable to use them.)
Create a new QOM interface which can be implemented by devices which
need to do something different from their default reset behaviour.
The callback will be called after machine initialization and before
first reset.
Suggested-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1441383782-24378-3-git-send-email-peter.maydell@linaro.org
The Linux kernel on aarch64 creates a page table entry at early bootup
that spans the 2MB range on memory spanning the fdt start address:
[ ALIGN_DOWN(fdt, 2MB) ... ALIGN_DOWN(fdt, 2MB) + 2MB ]
This means that when our current 4k alignment happens to fall at the end
of the aligned region, Linux tries to access memory that is not mapped.
The easy fix is to instead increase the alignment to 2MB, making Linux's
logic always succeed.
We leave the existing 4k alignment for 32bit kernels to not cause any
regressions due to space constraints.
Reported-by: Andreas Schwab <schwab@suse.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use cpu_set_pc() across the board for setting program counters. This
removes instances of system level code having to reach into the CPU
env.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
[AF: Avoid repeated casts with local variables]
Signed-off-by: Andreas Färber <afaerber@suse.de>
commit ac9d32e396 had the consequence to
register the do_cpu_reset after the rom_reset one. Hence they get
executed in the wrong order. This commit restores the registration of
do_cpu_reset in arm_load_kernel.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Reported-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Tested-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: 1434111582-9325-1-git-send-email-eric.auger@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Device tree nodes for the platform bus and its children dynamic sysbus
devices are added in a machine init done notifier. To load the dtb once,
after those latter nodes are built and before ROM freeze, the actual
arm_load_kernel existing code is moved into a notifier notify function,
arm_load_kernel_notify. arm_load_kernel now only registers the
corresponding notifier.
Machine files that do not support platform bus stay unchanged. Machine
files willing to support dynamic sysbus devices must call arm_load_kernel
before sysbus-fdt arm_register_platform_bus_fdt_creator to make sure
dynamic sysbus device nodes are integrated in the dtb.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Reviewed-by: Shannon Zhao <zhaoshenglong@huawei.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1433244554-12898-3-git-send-email-eric.auger@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Switch all the uses of ld/st*_phys to address_space_ld/st*,
except for those cases where the address space is the CPU's
(ie cs->as). This was done with the following script which
generates a Coccinelle patch.
A few over-80-columns lines in the result were rewrapped by
hand where Coccinelle failed to do the wrapping automatically,
as well as one location where it didn't put a line-continuation
'\' when wrapping lines on a change made to a match inside
a macro definition.
===begin===
#!/bin/sh -e
# Usage:
# ./ldst-phys.spatch.sh > ldst-phys.spatch
# spatch -sp_file ldst-phys.spatch -dir . | sed -e '/^+/s/\t/ /g' > out.patch
# patch -p1 < out.patch
for FN in ub uw_le uw_be l_le l_be q_le q_be uw l q; do
cat <<EOF
@ cpu_matches_ld_${FN} @
expression E1,E2;
identifier as;
@@
ld${FN}_phys(E1->as,E2)
@ other_matches_ld_${FN} depends on !cpu_matches_ld_${FN} @
expression E1,E2;
@@
-ld${FN}_phys(E1,E2)
+address_space_ld${FN}(E1,E2, MEMTXATTRS_UNSPECIFIED, NULL)
EOF
done
for FN in b w_le w_be l_le l_be q_le q_be w l q; do
cat <<EOF
@ cpu_matches_st_${FN} @
expression E1,E2,E3;
identifier as;
@@
st${FN}_phys(E1->as,E2,E3)
@ other_matches_st_${FN} depends on !cpu_matches_st_${FN} @
expression E1,E2,E3;
@@
-st${FN}_phys(E1,E2,E3)
+address_space_st${FN}(E1,E2,E3, MEMTXATTRS_UNSPECIFIED, NULL)
EOF
done
===endit===
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Update to arm_cpu_reset() to reset into the highest available exception level
based on the set ARM features.
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1422029835-4696-4-git-send-email-greg.bellows@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Introduce the new boolean field "arm_boot_info.firmware_loaded". When this
field is set, it means that the portion of guest DRAM that the VCPU
normally starts to execute, or the pflash chip that the VCPU normally
starts to execute, has been populated by board-specific code with
full-fledged guest firmware code, before the board calls
arm_load_kernel().
Simultaneously, "arm_boot_info.firmware_loaded" guarantees that the board
code has set up the global firmware config instance, for arm_load_kernel()
to find with fw_cfg_find().
Guest kernel (-kernel) and guest firmware (-bios, -pflash) has always been
possible to specify independently on the command line. The following cases
should be considered:
nr -bios -pflash -kernel description
unit#0
-- ------- ------- ------- -------------------------------------------
1 present present absent Board code rejects this case, -bios and
present present present -pflash unit#0 are exclusive. Left intact
by this patch.
2 absent absent present Traditional kernel loading, with qemu's
minimal board firmware. Left intact by this
patch.
3 absent present absent Preexistent case for booting guest firmware
present absent absent loaded with -bios or -pflash. Left intact
by this patch.
4 absent absent absent Preexistent case for not loading any
firmware or kernel up-front. Left intact by
this patch.
5 present absent present New case introduced by this patch: kernel
absent present present image is passed to externally loaded
firmware in unmodified form, using fw_cfg.
An easy way to see that this patch doesn't interfere with existing cases
is to realize that "info->firmware_loaded" is constant zero at this point.
Which makes the "outer" condition unchanged, and the "inner" condition
(with the fw_cfg-related code) dead.
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1419250305-31062-11-git-send-email-pbonzini@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Adds the secure_boot boolean field to the arm_boot_info descriptor. This
fields is used to indicate whether Linux should boot into secure or non-secure
state if the ARM EL3 feature is enabled. The default is to leave the CPU in an
unaltered reset state. On EL3 enabled systems, the reset state is secure and
can be overridden by setting the added field to false.
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1418684992-8996-11-git-send-email-greg.bellows@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Coverity reports the 'size' may be used uninitialized, but that can't happen,
because the caller has checked "if (binfo->dtb_filename || binfo->get_dtb)"
before call 'load_dtb'.
Here we simply remove the 'if (binfo->get_dtb)' to satisfy coverity.
Signed-off-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
Message-id: 1416826240-12368-1-git-send-email-zhang.zhanghailiang@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Such address translation is needed when load address recorded in uImage
is a virtual address. When the actual load address is requested, return
untranslated address: user that needs the translated address can always
apply translation function to it and those that need it untranslated
don't need to do the inverse translation.
Add translation function pointer and its parameter to uimage_load
prototype. Update all existing users.
No user-visible functional changes.
Cc: qemu-stable@nongnu.org
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Move the registering of CPU reset handlers to before the point where
we leave the function in the -bios (not -kernel) case, so CPU reset
works correctly with -bios as well.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add support for loading DTB images when booting ELF images using
-kernel. If there are no conflicts with the placement of the ELF
segments, the DTB image is loaded at the base of RAM.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Message-id: 1410453915-9344-5-git-send-email-ard.biesheuvel@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If we are running the 'virt' machine, we may have a device tree blob but no
kernel to supply it to if no -kernel option was passed. In that case, copy it
to the base of RAM where it can be picked up by a bootloader.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Message-id: 1410453915-9344-4-git-send-email-ard.biesheuvel@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add an address limit input parameter to load_dtb() so that we can
tell load_dtb() how much memory the dtb is allowed to consume. If
the dtb doesn't fit, return 0, otherwise return the actual size of
the loaded dtb.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Message-id: 1410453915-9344-3-git-send-email-ard.biesheuvel@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
