In the TZ Memory Protection Controller, the BLK_MAX register is supposed
to return the maximum permitted value of the BLK_IDX register. Our
implementation incorrectly returned max+1 (ie the total number of
valid index values, since BLK_IDX is zero-based).
Correct this off-by-one error. Since we consistently initialize
and use s->blk_max throughout the implementation as the 'size'
of the LUT, just adjust the value we return when the guest reads
the BLK_MAX register, rather than trying to change the semantics
of the s->blk_max internal struct field.
Fixes: https://bugs.launchpad.net/qemu/+bug/1806824
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20181213183249.3468-1-peter.maydell@linaro.org
This stubs enables the microbit-micropython firmware to run
on the microbit machine.
Signed-off-by: Steffen Görtz <contrib@steffen-goertz.de>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190103091119.9367-12-stefanha@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch adds the model for the nRF51 timer peripheral.
Currently, only the TIMER mode is implemented.
Signed-off-by: Steffen Görtz <contrib@steffen-goertz.de>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190103091119.9367-9-stefanha@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This adds a model of the nRF51 GPIO peripheral.
Reference Manual: http://infocenter.nordicsemi.com/pdf/nRF51_RM_v3.0.pdf
The nRF51 series microcontrollers support up to 32 GPIO pins in various configurations.
The pins can be used as input pins with pull-ups or pull-down.
Furthermore, three different output driver modes per level are
available (disconnected, standard, high-current).
The GPIO-Peripheral has a mechanism for detecting level changes which is
not featured in this model.
Signed-off-by: Steffen Görtz <contrib@steffen-goertz.de>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190103091119.9367-6-stefanha@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use RNG in SOC.
Signed-off-by: Steffen Görtz <contrib@steffen-goertz.de>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190103091119.9367-5-stefanha@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a model of the NRF51 random number generator peripheral.
This is a simple random generator that continuously generates
new random values after startup.
Reference Manual: http://infocenter.nordicsemi.com/pdf/nRF51_RM_v3.0.pdf
Signed-off-by: Steffen Görtz <contrib@steffen-goertz.de>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190103091119.9367-4-stefanha@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Adds a header that provides definitions that are used
across nRF51 peripherals
Signed-off-by: Steffen Görtz <contrib@steffen-goertz.de>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190103091119.9367-3-stefanha@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
From the "A10 User Manual V1.20" p.29: "3.2. Memory Mapping" and:
7. System Control
7.1. Overview
A10 embeds a high-speed SRAM which has been split into five segments.
See detailed memory mapping in following table:
Area Address Size (Bytes)
A1 0x00000000-0x00003FFF 16K
A2 0x00004000-0x00007FFF 16K
A3 0x00008000-0x0000B3FF 13K
A4 0x0000B400-0x0000BFFF 3K
Since for emulation purpose we don't need the segmentations, we simply define
the 'A' area as a single 48KB SRAM.
We don't implement the following others areas:
- 'B': 'Secure RAM' (64K),
- 'C': Debug/ISP SRAM
- 'D': USB SRAM
(qemu) info mtree
address-space: memory
0000000000000000-ffffffffffffffff (prio 0, i/o): system
0000000000000000-000000000000bfff (prio 0, ram): sram A
0000000001c00000-0000000001c00fff (prio -1000, i/o): a10-sram-ctrl
0000000001c0b000-0000000001c0bfff (prio 0, i/o): aw_emac
0000000001c18000-0000000001c18fff (prio 0, i/o): ahci
0000000001c18080-0000000001c180ff (prio 0, i/o): allwinner-ahci
0000000001c20400-0000000001c207ff (prio 0, i/o): allwinner-a10-pic
0000000001c20c00-0000000001c20fff (prio 0, i/o): allwinner-A10-timer
0000000001c28000-0000000001c2801f (prio 0, i/o): serial
0000000040000000-0000000047ffffff (prio 0, ram): cubieboard.ram
Reported-by: Charlie Smurthwaite <charlie@atech.media>
Tested-by: Charlie Smurthwaite <charlie@atech.media>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20190104142921.878-1-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Plug a couple of "board creation time" memory leaks.
Fixes: 6f16da53ff ("hw/arm: versal: Add a virtual Xilinx Versal board")
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190104104749.5314-2-edgar.iglesias@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This reverts commit 01fd41ab3f.
The generic loader device (-device loader,file=kernel.bin) can be used
to load a kernel instead of the -kernel option. Some boards have flash
memory (pflash) that is set via the -pflash or -drive options.
Allow starting QEMU without the -kernel option to accommodate these
scenarios.
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190103144124.18917-1-stefanha@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Create two separate CPU clusters for APUs and RPUs.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20181207090135.7651-17-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This commit adds the cpu-cluster type. It aims at gathering CPUs from
the same cluster in a machine.
For now it only has a `cluster-id` property.
Documentation in cluster.h written with the help of Peter Maydell.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20181207090135.7651-2-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In previous commit:
commit 7dea29e4af
Author: Li Qiang <liq3ea@gmail.com>
Date: Fri Oct 19 03:50:36 2018 -0700
hw: ccid-card-emulated: cleanup resource when realize in error path
The emulated_realize method was changed so that it jumps to a cleanup
label to de-initialize state upon error. This change failed to ensure
the success path exited the method before this point though. So the
mutexes are always destroyed even in normal operation. The result is
as crashtastic as expected:
$ qemu-system-x86_64 -usb -device usb-ccid,id=ccid0 -device ccid-card-emulated,backend=nss-emulated,id=smartcard0,bus=ccid0.0
qemu-system-x86_64: util/qemu-thread-posix.c:64: qemu_mutex_lock_impl: Assertion `mutex->initialized' failed.
Aborted (core dumped)
Fixes: 7dea29e4af
Reported-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20181221134115.27973-1-berrange@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
hostmem-file and hostmem-memfd use the whole object path for the
memory region name, and hostname-ram uses only the path component (the
object id, or canonical path basename):
qemu -m 1024 -object memory-backend-file,id=mem,size=1G,mem-path=/tmp/foo -numa node,memdev=mem -monitor stdio
(qemu) info ramblock
Block Name PSize Offset Used Total
/objects/mem 4 KiB 0x0000000000000000 0x0000000040000000 0x0000000040000000
qemu -m 1024 -object memory-backend-memfd,id=mem,size=1G -numa node,memdev=mem -monitor stdio
(qemu) info ramblock
Block Name PSize Offset Used Total
/objects/mem 4 KiB 0x0000000000000000 0x0000000040000000 0x0000000040000000
qemu -m 1024 -object memory-backend-ram,id=mem,size=1G -numa node,memdev=mem -monitor stdio
(qemu) info ramblock
Block Name PSize Offset Used Total
mem 4 KiB 0x0000000000000000 0x0000000040000000 0x0000000040000000
For consistency, change to use object id for -file and -memfd as well
with >= 4.0.
Having a consistent naming allows to migrate to different hostmem
backends.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
It's now possible to use the common function.
Teach object_apply_global_props() to warn if Error argument is NULL.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
All qdev_prop_register_global() set &error_fatal for errp, except
'-rtc driftfix=slew', which arguably should also use &error_fatal, as
otherwise failing to apply the property would only report a warning.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
A step towards being able to call a common function,
object_apply_global_props().
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
All globals are now either provided via -global or through -cpu
features (CPU features are implemented by registering globals).
If the global isn't being used, it should warn in either case.
We can thus consider that all global_props are "user-provided"
globals. No need to track this per-globals anymore.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
This will allow to apply compat properties on other objects than QDev easily.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
Use static arrays instead. I decided to rename the conflicting
pc_compat_2_1() function with pc_compat_2_1_fn().
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
Use static arrays instead. I decided to rename the conflicting
pc_compat_2_1() function with pc_compat_2_1_fn().
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
Use static arrays instead. I decided to rename the conflicting
pc_compat_2_2() function with pc_compat_2_2_fn().
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
Use static arrays instead. I decided to rename the conflicting
pc_compat_2_3() function with pc_compat_2_3_fn().
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
Similarly to accel properties, move compat properties out of globals
registration, and apply the machine compat properties during
device_post_init().
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
Instead of registering compat properties as globals, let's keep them
in their own array, to avoid mixing with user globals.
Introduce object_apply_global_props() function, to apply compatibility
properties from a GPtrArray.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
qemu_extra_params_fw[] has external linkage, but is used
only in fw_cfg_bootsplash(), it makes sense to make it
locally.
Signed-off-by: Li Qiang <liq3ea@gmail.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <1542777026-2788-4-git-send-email-liq3ea@gmail.com>
[PMD: Removed qemu_extra_params_fw declaration in vl.c]
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
fw_cfg_reboot() gets option parameter "reboot-timeout" with
qemu_opt_get(), then converts it to an integer by hand. It neglects to
check that conversion for errors, and fails to reject negative values.
Positive values above the limit get reported and replaced by the limit.
This patch checks for conversion errors properly, and reject all values
outside 0...0xffff.
Signed-off-by: Li Qiang <liq3ea@gmail.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <1542777026-2788-3-git-send-email-liq3ea@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
fw_cfg_bootsplash() gets option parameter "splash-time"
with qemu_opt_get(), then converts it to an integer by hand.
It neglects to check that conversion for errors. This is
needlessly complicated and error-prone. But as "splash-time
not specified" is not the same as "splash-time=T" for any T,
we need use qemu_opt_get() to check if splash time exists.
This patch also make the qemu exit when finding or loading
splash file failed.
Signed-off-by: Li Qiang <liq3ea@gmail.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <1542777026-2788-2-git-send-email-liq3ea@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
read_splashfile() reports "failed to read splash file" without
further details. Get the details from g_file_get_contents(), and
include them in the error message. Also remove unnecessary 'res'
variable.
Signed-off-by: Li Qiang <liq3ea@gmail.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <1541052148-28752-1-git-send-email-liq3ea@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
This pull request contains the first set of RISC-V patches I'd like to
target for the 3.2 development cycle. It's really just a collection of
bug fixes with one major new feature: PCIe can now be attached to RISC-V
guests.
This has passed my usual test of booting the latest Linux RC into a
Fedora disk image on the virt machine.
-----BEGIN PGP SIGNATURE-----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=BAOm
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/palmer/tags/riscv-for-master-3.2-part1' into staging
RISC-V Changes for 3.2, Part 1
This pull request contains the first set of RISC-V patches I'd like to
target for the 3.2 development cycle. It's really just a collection of
bug fixes with one major new feature: PCIe can now be attached to RISC-V
guests.
This has passed my usual test of booting the latest Linux RC into a
Fedora disk image on the virt machine.
# gpg: Signature made Fri 21 Dec 2018 16:01:29 GMT
# gpg: using RSA key EF4CA1502CCBAB41
# gpg: Good signature from "Palmer Dabbelt <palmer@dabbelt.com>"
# gpg: aka "Palmer Dabbelt <palmer@sifive.com>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 00CE 76D1 8349 60DF CE88 6DF8 EF4C A150 2CCB AB41
* remotes/palmer/tags/riscv-for-master-3.2-part1:
MAINTAINERS: Mark RISC-V as Supported
riscv/cpu: use device_class_set_parent_realize
target/riscv/pmp.c: Fix pmp_decode_napot()
sifive_uart: Implement interrupt pending register
RISC-V: Enable second UART on sifive_e and sifive_u
RISC-V: Fix PLIC pending bitfield reads
RISC-V: Fix CLINT timecmp low 32-bit writes
RISC-V: Add hartid and \n to interrupt logging
sifive_u: Set 'clock-frequency' DT property for SiFive UART
sifive_u: Add clock DT node for GEM ethernet
riscv: Enable VGA and PCIE_VGA
hw/riscv/virt: Connect the gpex PCIe
hw/riscv/virt: Adjust memory layout spacing
hw/riscv/virt: Increase the number of interrupts
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
pvrdma_idx_ring_has_[data/space] routines also return invalid
index PVRDMA_INVALID_IDX[=-1], if ring has no data/space. Check
return value from these routines to avoid plausible infinite loops.
Reported-by: Li Qiang <liq3ea@163.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
With commit 4481985c (rdma: check num_sge does not exceed MAX_SGE)
macro VENDOR_ERR_NO_SGE is no longer in use - delete it.
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
create_cq and create_qp routines allocate ring object, but it's
not released in case of an error, leading to memory leakage.
Reported-by: Li Qiang <liq3ea@163.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
When creating CQ/QP rings, an object can have up to
PVRDMA_MAX_FAST_REG_PAGES 8 pages. Check 'npages' parameter
to avoid excessive memory allocation or a null dereference.
Reported-by: Li Qiang <liq3ea@163.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
rdma back-end has scatter/gather array ibv_sge[MAX_SGE=4] set
to have 4 elements. A guest could send a 'PvrdmaSqWqe' ring element
with 'num_sge' set to > MAX_SGE, which may lead to OOB access issue.
Add check to avoid it.
Reported-by: Saar Amar <saaramar5@gmail.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
If during pvrdma device initialisation an error occurs,
pvrdma_realize() does not release memory resources, leading
to memory leakage.
Reported-by: Li Qiang <liq3ea@163.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-Id: <20181212175817.815-1-ppandit@redhat.com>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
When device goes down the function fini_ports loops over all entries in
gid table regardless of the fact whether entry is valid or not. In case
that entry is not valid we'd like to skip from any further processing in
backend device.
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Signed-off-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
bitmap_zero_extend is designed to work for extending, not for
shrinking.
Using g_free instead.
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Signed-off-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
In order to clean some external resources such as GIDs, QPs etc,
register to receive notification when VM is shutdown.
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Signed-off-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Device supports only one port, let's remove a dead code that handles
more than one port.
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Signed-off-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Driver checks error code let's set it.
In addition, for code simplification purposes, set response's fields
ack, response and err outside of the scope of command handlers.
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Signed-off-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Add ability to pass specific WC attributes to CQE such as GRH_BIT flag.
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Signed-off-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
User should be able to control the device by changing Ethernet function
state so if user runs 'ifconfig ens3 down' the PVRDMA function should be
down as well.
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Signed-off-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
node_guid should be set once device is load.
Make node_guid be GID format (32 bit) of PCI function 0 vmxnet3 device's
MAC.
A new function was added to do the conversion.
So for example the MAC 56:b6:44:e9:62:dc will be converted to GID
54b6:44ff:fee9:62dc.
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Signed-off-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
pvrdma setup requires vmxnet3 device on PCI function 0 and PVRDMA device
on PCI function 1.
pvrdma device needs to access vmxnet3 device object for several reasons:
1. Make sure PCI function 0 is vmxnet3.
2. To monitor vmxnet3 device state.
3. To configure node_guid accoring to vmxnet3 device's MAC address.
To be able to access vmxnet3 device the definition of VMXNET3State is
moved to a new header file.
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Dmitry Fleytman <dmitry.fleytman@gmail.com>
Signed-off-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
The control over the RDMA device's GID table is done by updating the
device's Ethernet function addresses.
Usually the first GID entry is determined by the MAC address, the second
by the first IPv6 address and the third by the IPv4 address. Other
entries can be added by adding more IP addresses. The opposite is the
same, i.e. whenever an address is removed, the corresponding GID entry
is removed.
The process is done by the network and RDMA stacks. Whenever an address
is added the ib_core driver is notified and calls the device driver
add_gid function which in turn update the device.
To support this in pvrdma device we need to hook into the create_bind
and destroy_bind HW commands triggered by pvrdma driver in guest.
Whenever a change is made to the pvrdma port's GID table a special QMP
message is sent to be processed by libvirt to update the address of the
backend Ethernet device.
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Marcel Apfelbaum<marcel.apfelbaum@gmail.com>
Signed-off-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
opcode for WC should be set by the device and not taken from work
element.
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Signed-off-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
The function pvrdma_post_cqe populates CQE entry with opcode from the
given completion element. For receive operation value was not set. Fix
it by setting it to IBV_WC_RECV.
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Signed-off-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
MAD (Management Datagram) packets are widely used by various modules
both in kernel and in user space for example the rdma_* API which is
used to create and maintain "connection" layer on top of RDMA uses
several types of MAD packets.
For more information please refer to chapter 13.4 in Volume 1
Architecture Specification, Release 1.1 available here:
https://www.infinibandta.org/ibta-specifications-download/
To support MAD packets the device uses an external utility
(contrib/rdmacm-mux) to relay packets from and to the guest driver.
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Marcel Apfelbaum<marcel.apfelbaum@gmail.com>
Signed-off-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Upon completion of incoming packet the device pushes CQE to driver's RX
ring and notify the driver (msix).
While for data-path incoming packets the driver needs the ability to
control whether it wished to receive interrupts or not, for control-path
packets such as incoming MAD the driver needs to be notified anyway, it
even do not need to re-arm the notification bit.
Enhance the notification field to support this.
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Signed-off-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Return value of 0 means ok, we want to free the memory only in case of
error.
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Message-Id: <20181025061700.17050-1-yuval.shaia@oracle.com>
Reviewed-by: Marcel Apfelbaum<marcel.apfelbaum@gmail.com>
Signed-off-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
This pull request supersedes the one from 2018-12-13.
This is a revised first ppc pull request for qemu-4.0. Highlights
are:
* Most of the code for the POWER9 "XIVE" interrupt controller
(not complete yet, but we're getting there)
* A number of g_new vs. g_malloc cleanups
* Some IRQ wiring cleanups
* A fix for how we advertise NUMA nodes to the guest for pseries
-----BEGIN PGP SIGNATURE-----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=IN1s
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-4.0-20181221' into staging
ppc patch queue 2018-12-21
This pull request supersedes the one from 2018-12-13.
This is a revised first ppc pull request for qemu-4.0. Highlights
are:
* Most of the code for the POWER9 "XIVE" interrupt controller
(not complete yet, but we're getting there)
* A number of g_new vs. g_malloc cleanups
* Some IRQ wiring cleanups
* A fix for how we advertise NUMA nodes to the guest for pseries
# gpg: Signature made Fri 21 Dec 2018 05:34:12 GMT
# gpg: using RSA key 6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>"
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-4.0-20181221: (40 commits)
MAINTAINERS: PPC: add a XIVE section
spapr: change default CPU type to POWER9
spapr: introduce an 'ic-mode' machine option
spapr: add an extra OV5 field to the sPAPR IRQ backend
spapr: add a 'reset' method to the sPAPR IRQ backend
spapr: extend the sPAPR IRQ backend for XICS migration
spapr: allocate the interrupt thread context under the CPU core
spapr: add device tree support for the XIVE exploitation mode
spapr: add hcalls support for the XIVE exploitation interrupt mode
spapr: introduce a new machine IRQ backend for XIVE
spapr-iommu: Always advertise the maximum possible DMA window size
spapr/xive: use the VCPU id as a NVT identifier
spapr/xive: introduce a XIVE interrupt controller
ppc/xive: notify the CPU when the interrupt priority is more privileged
ppc/xive: introduce a simplified XIVE presenter
ppc/xive: introduce the XIVE interrupt thread context
ppc/xive: add support for the END Event State Buffers
Changes requirement for "vsubsbs" instruction
spapr: export and rename the xics_max_server_number() routine
spapr: introduce a spapr_irq_init() routine
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
VTD fixes
IR and split irqchip are now the default for Q35
ACPI refactoring
hotplug refactoring
new names for virtio devices
multiple pcie link width/speeds
PCI fixes
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJcG967AAoJECgfDbjSjVRpUlMH/1wy8WW7Br/4JxlWUPsfZTqZ
0Lg2n59wuFzRVS+gLotp6bUaJGR9xn9fKjI1wfD59oVrDTKyauuw82v0OityEs33
ZquFecuJvP6k5N40DkqA9YJjKSw7nUmLrsyrD0t2H43npikP2aD9f6yootrr3oVV
nPwBvyT9ykIBQc7IzsHDiLw3EPdIf+9IR7+l+PLptzV0zK43Jfwi/nzHIQq00UMz
eLM/ejQLIx4BZJnYGS0Cy6v3K7cS3k45LHDY0cGc0id2jHFN2vdQyHCF9I1ps72q
pSlhMaLEwvQSYyre6iFTG5uuvyIPWv3LOkaBEwMSA5B/HXuEb2RKHThYzS9dc68=
=OwW7
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pci, pc, virtio: fixes, features
VTD fixes
IR and split irqchip are now the default for Q35
ACPI refactoring
hotplug refactoring
new names for virtio devices
multiple pcie link width/speeds
PCI fixes
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Thu 20 Dec 2018 18:26:03 GMT
# gpg: using RSA key 281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (44 commits)
x86-iommu: turn on IR by default if proper
x86-iommu: switch intr_supported to OnOffAuto type
q35: set split kernel irqchip as default
pci: Adjust PCI config limit based on bus topology
spapr_pci: perform unplug via the hotplug handler
pci/shpc: perform unplug via the hotplug handler
pci: Reuse pci-bridge hotplug handler handlers for pcie-pci-bridge
pci/pcie: perform unplug via the hotplug handler
pci/pcihp: perform unplug via the hotplug handler
pci/pcihp: overwrite hotplug handler recursively from the start
pci/pcihp: perform check for bus capability in pre_plug handler
s390x/pci: rename hotplug handler callbacks
pci/shpc: rename hotplug handler callbacks
pci/pcie: rename hotplug handler callbacks
hw/i386: Remove deprecated machines pc-0.10 and pc-0.11
hw: acpi: Remove AcpiRsdpDescriptor and fix tests
hw: acpi: Export and share the ARM RSDP build
hw: arm: Support both legacy and current RSDP build
hw: arm: Convert the RSDP build to the buid_append_foo() API
hw: arm: Carry RSDP specific data through AcpiRsdpData
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This option is used to select the interrupt controller mode (XICS or
XIVE) with which the machine will operate. XICS being the default
mode for now.
When running a machine with the XIVE interrupt mode backend, the guest
OS is required to have support for the XIVE exploitation mode. In the
case of legacy OS, the mode selected by CAS should be XICS and the OS
should fail to boot. However, QEMU could possibly detect it, terminate
the boot process and reset to stop in the SLOF firmware. This is not
yet handled.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The interrupt modes supported by the hypervisor are advertised to the
guest with new bits definitions of the option vector 5 of property
"ibm,arch-vec-5-platform-support. The byte 23 bits 0-1 of the OV5 are
defined as follow :
0b00 PAPR 2.7 and earlier (Legacy systems)
0b01 XIVE Exploitation mode only
0b10 Either available
If the client/guest selects the XIVE interrupt mode, it informs the
hypervisor by returning the value 0b01 in byte 23 bits 0-1. A 0b00
value indicates the use of the XICS interrupt mode (Legacy systems).
The sPAPR IRQ backend is extended with these definitions and the
values are directly used to populate the "ibm,arch-vec-5-platform-support"
property. The interrupt mode is advertised under TCG and under KVM.
Although a KVM XIVE device is not yet available, the machine can still
operate with kernel_irqchip=off. However, we apply a restriction on
the CPU which is required to be a POWER9 when a XIVE interrupt
controller is in use.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
For the time being, the XIVE reset handler updates the OS CAM line of
the vCPU as it is done under a real hypervisor when a vCPU is
scheduled to run on a HW thread. This will let the XIVE presenter
engine find a match among the NVTs dispatched on the HW threads.
This handler will become even more useful when we introduce the
machine supporting both interrupt modes, XIVE and XICS. In this
machine, the interrupt mode is chosen by the CAS negotiation process
and activated after a reset.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
[dwg: Fix style nits]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Introduce a new sPAPR IRQ handler to handle resend after migration
when the machine is using a KVM XICS interrupt controller model.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Each interrupt mode has its own specific interrupt presenter object,
that we store under the CPU object, one for XICS and one for XIVE.
Extend the sPAPR IRQ backend with a new handler to support them both.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The XIVE interface for the guest is described in the device tree under
the "interrupt-controller" node. A couple of new properties are
specific to XIVE :
- "reg"
contains the base address and size of the thread interrupt
managnement areas (TIMA), for the User level and for the Guest OS
level. Only the Guest OS level is taken into account today.
- "ibm,xive-eq-sizes"
the size of the event queues. One cell per size supported, contains
log2 of size, in ascending order.
- "ibm,xive-lisn-ranges"
the IRQ interrupt number ranges assigned to the guest for the IPIs.
and also under the root node :
- "ibm,plat-res-int-priorities"
contains a list of priorities that the hypervisor has reserved for
its own use. OPAL uses the priority 7 queue to automatically
escalate interrupts for all other queues (DD2.X POWER9). So only
priorities [0..6] are allowed for the guest.
Extend the sPAPR IRQ backend with a new handler to populate the DT
with the appropriate "interrupt-controller" node.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
[dwg: Fix style nits]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The different XIVE virtualization structures (sources and event queues)
are configured with a set of Hypervisor calls :
- H_INT_GET_SOURCE_INFO
used to obtain the address of the MMIO page of the Event State
Buffer (ESB) entry associated with the source.
- H_INT_SET_SOURCE_CONFIG
assigns a source to a "target".
- H_INT_GET_SOURCE_CONFIG
determines which "target" and "priority" is assigned to a source
- H_INT_GET_QUEUE_INFO
returns the address of the notification management page associated
with the specified "target" and "priority".
- H_INT_SET_QUEUE_CONFIG
sets or resets the event queue for a given "target" and "priority".
It is also used to set the notification configuration associated
with the queue, only unconditional notification is supported for
the moment. Reset is performed with a queue size of 0 and queueing
is disabled in that case.
- H_INT_GET_QUEUE_CONFIG
returns the queue settings for a given "target" and "priority".
- H_INT_RESET
resets all of the guest's internal interrupt structures to their
initial state, losing all configuration set via the hcalls
H_INT_SET_SOURCE_CONFIG and H_INT_SET_QUEUE_CONFIG.
- H_INT_SYNC
issue a synchronisation on a source to make sure all notifications
have reached their queue.
Calls that still need to be addressed :
H_INT_SET_OS_REPORTING_LINE
H_INT_GET_OS_REPORTING_LINE
See the code for more documentation on each hcall.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
[dwg: Folded in fix for field accessors]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The XIVE IRQ backend uses the same layout as the new XICS backend but
covers the full range of the IRQ number space. The IRQ numbers for the
CPU IPIs are allocated at the bottom of this space, below 4K, to
preserve compatibility with XICS which does not use that range.
This should be enough given that the maximum number of CPUs is 1024
for the sPAPR machine under QEMU. For the record, the biggest POWER8
or POWER9 system has a maximum of 1536 HW threads (16 sockets, 192
cores, SMT8).
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When deciding about the huge DMA window, the typical Linux pseries guest
uses the maximum allowed RAM size as the upper limit. We did the same
on QEMU side to match that logic. Now we are going to support a GPU RAM
pass through which is not available at the guest boot time as it requires
the guest driver interaction. As the result, the guest requests a smaller
window than it should. Therefore the guest needs to be patched to
understand this new memory and so does QEMU.
Instead of reimplementing here whatever solution we choose for the guest,
this advertises the biggest possible window size limited by 32 bit
(as defined by LoPAPR). Since the window size has to be power-of-two
(the create rtas call receives a window shift, not a size),
this uses 0x8000.0000 as the maximum number of TCEs possible (rather than
32bit maximum of 0xffff.ffff).
This is safe as:
1. The guest visible emulated table is allocated in KVM (actual pages
are allocated in page fault handler) and QEMU (actual pages are allocated
when updated);
2. The hardware table (and corresponding userspace address table)
supports sparse allocation and also checks for locked_vm limit so
it is unable to cause the host any damage.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The IVPE scans the O/S CAM line of the XIVE thread interrupt contexts
to find a matching Notification Virtual Target (NVT) among the NVTs
dispatched on the HW processor threads.
On a real system, the thread interrupt contexts are updated by the
hypervisor when a Virtual Processor is scheduled to run on a HW
thread. Under QEMU, the model will emulate the same behavior by
hardwiring the NVT identifier in the thread context registers at
reset.
The NVT identifier used by the sPAPRXive model is the VCPU id. The END
identifier is also derived from the VCPU id. A set of helpers doing
the conversion between identifiers are provided for the hcalls
configuring the sources and the ENDs.
The model does not need a NVT table but the XiveRouter NVT operations
are provided to perform some extra checks in the routing algorithm.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
sPAPRXive models the XIVE interrupt controller of the sPAPR machine.
It inherits from the XiveRouter and provisions storage for the routing
tables :
- Event Assignment Structure (EAS)
- Event Notification Descriptor (END)
The sPAPRXive model incorporates an internal XiveSource for the IPIs
and for the interrupts of the virtual devices of the guest. This model
is consistent with XIVE architecture which also incorporates an
internal IVSE for IPIs and accelerator interrupts in the IVRE
sub-engine.
The sPAPRXive model exports two memory regions, one for the ESB
trigger and management pages used to control the sources and one for
the TIMA pages. They are mapped by default at the addresses found on
chip 0 of a baremetal system. This is also consistent with the XIVE
architecture which defines a Virtualization Controller BAR for the
internal IVSE ESB pages and a Thread Managment BAR for the TIMA.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
[dwg: Fold in field accessor fixes]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
After the event data was enqueued in the O/S Event Queue, the IVPE
raises the bit corresponding to the priority of the pending interrupt
in the register IBP (Interrupt Pending Buffer) to indicate there is an
event pending in one of the 8 priority queues. The Pending Interrupt
Priority Register (PIPR) is also updated using the IPB. This register
represent the priority of the most favored pending notification.
The PIPR is then compared to the the Current Processor Priority
Register (CPPR). If it is more favored (numerically less than), the
CPU interrupt line is raised and the EO bit of the Notification Source
Register (NSR) is updated to notify the presence of an exception for
the O/S. The check needs to be done whenever the PIPR or the CPPR are
changed.
The O/S acknowledges the interrupt with a special load in the Thread
Interrupt Management Area. If the EO bit of the NSR is set, the CPPR
takes the value of PIPR. The bit number in the IBP corresponding to
the priority of the pending interrupt is reseted and so is the EO bit
of the NSR.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
[dwg: Fix style nits]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The last sub-engine of the XIVE architecture is the Interrupt
Virtualization Presentation Engine (IVPE). On HW, the IVRE and the
IVPE share elements, the Power Bus interface (CQ), the routing table
descriptors, and they can be combined in the same HW logic. We do the
same in QEMU and combine both engines in the XiveRouter for
simplicity.
When the IVRE has completed its job of matching an event source with a
Notification Virtual Target (NVT) to notify, it forwards the event
notification to the IVPE sub-engine. The IVPE scans the thread
interrupt contexts of the Notification Virtual Targets (NVT)
dispatched on the HW processor threads and if a match is found, it
signals the thread. If not, the IVPE escalates the notification to
some other targets and records the notification in a backlog queue.
The IVPE maintains the thread interrupt context state for each of its
NVTs not dispatched on HW processor threads in the Notification
Virtual Target table (NVTT).
The model currently only supports single NVT notifications.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
[dwg: Folded in fix for field accessors]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Each POWER9 processor chip has a XIVE presenter that can generate four
different exceptions to its threads:
- hypervisor exception,
- O/S exception
- Event-Based Branch (EBB)
- msgsnd (doorbell).
Each exception has a state independent from the others called a Thread
Interrupt Management context. This context is a set of registers which
lets the thread handle priority management and interrupt acknowledgment
among other things. The most important ones being :
- Interrupt Priority Register (PIPR)
- Interrupt Pending Buffer (IPB)
- Current Processor Priority (CPPR)
- Notification Source Register (NSR)
These registers are accessible through a specific MMIO region, called
the Thread Interrupt Management Area (TIMA), four aligned pages, each
exposing a different view of the registers. First page (page address
ending in 0b00) gives access to the entire context and is reserved for
the ring 0 view for the physical thread context. The second (page
address ending in 0b01) is for the hypervisor, ring 1 view. The third
(page address ending in 0b10) is for the operating system, ring 2
view. The fourth (page address ending in 0b11) is for user level, ring
3 view.
The thread interrupt context is modeled with a XiveTCTX object
containing the values of the different exception registers. The TIMA
region is mapped at the same address for each CPU.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The Event Notification Descriptor (END) XIVE structure also contains
two Event State Buffers providing further coalescing of interrupts,
one for the notification event (ESn) and one for the escalation events
(ESe). A MMIO page is assigned for each to control the EOI through
loads only. Stores are not allowed.
The END ESBs are modeled through an object resembling the 'XiveSource'
It is stateless as the END state bits are backed into the XiveEND
structure under the XiveRouter and the MMIO accesses follow the same
rules as for the XiveSource ESBs.
END ESBs are not supported by the Linux drivers neither on OPAL nor on
sPAPR. Nevetherless, it provides a mean to study the question in the
future and validates a bit more the XIVE model.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
[dwg: Fold in a later fix for field access]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The XIVE sPAPR IRQ backend will use it to define the number of ENDs of
the IC controller.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Initialize the MSI bitmap from it as this will be necessary for the
sPAPR IRQ backend for XIVE.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
We will need to use xics_max_server_number() to create the sPAPRXive
object modeling the interrupt controller of the machine which is
created before the CPUs.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
[dwg: Fix style nit]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
To complete the event routing, the IVRE sub-engine uses a second table
containing Event Notification Descriptor (END) structures.
An END specifies on which Event Queue (EQ) the event notification
data, defined in the associated EAS, should be posted when an
exception occurs. It also defines which Notification Virtual Target
(NVT) should be notified.
The Event Queue is a memory page provided by the O/S defining a
circular buffer, one per server and priority couple, containing Event
Queue entries. These are 4 bytes long, the first bit being a
'generation' bit and the 31 following bits the END Data field. They
are pulled by the O/S when the exception occurs.
The END Data field is a way to set an invariant logical event source
number for an IRQ. On sPAPR machines, it is set with the
H_INT_SET_SOURCE_CONFIG hcall when the EISN flag is used.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
[dwg: Fold in a later fix from Cédric fixing field accessors]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The XiveRouter models the second sub-engine of the XIVE architecture :
the Interrupt Virtualization Routing Engine (IVRE).
The IVRE handles event notifications of the IVSE and performs the
interrupt routing process. For this purpose, it uses a set of tables
stored in system memory, the first of which being the Event Assignment
Structure (EAS) table.
The EAT associates an interrupt source number with an Event Notification
Descriptor (END) which will be used in a second phase of the routing
process to identify a Notification Virtual Target.
The XiveRouter is an abstract class which needs to be inherited from
to define a storage for the EAT, and other upcoming tables.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
[dwg: Folded in parts of a later fix by Cédric fixing field access]
[dwg: Fix style nits]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The XiveNotifier offers a simple interface, between the XiveSource
object and the main interrupt controller of the machine. It will
forward event notifications to the XIVE Interrupt Virtualization
Routing Engine (IVRE).
Signed-off-by: Cédric Le Goater <clg@kaod.org>
[dwg: Adjust type name string for XiveNotifier]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The 'sent' status of the LSI interrupt source is modeled with the 'P'
bit of the ESB and the assertion status of the source is maintained
with an extra bit under the main XiveSource object. The type of the
source is stored in the same array for practical reasons.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
[dwg: Fix style nit]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The first sub-engine of the overall XIVE architecture is the Interrupt
Virtualization Source Engine (IVSE). An IVSE can be integrated into
another logic, like in a PCI PHB or in the main interrupt controller
to manage IPIs.
Each IVSE instance is associated with an Event State Buffer (ESB) that
contains a two bit state entry for each possible event source. When an
event is signaled to the IVSE, by MMIO or some other means, the
associated interrupt state bits are fetched from the ESB and
modified. Depending on the resulting ESB state, the event is forwarded
to the IVRE sub-engine of the controller doing the routing.
Each supported ESB entry is associated with either a single or a
even/odd pair of pages which provides commands to manage the source:
to EOI, to turn off the source for instance.
On a sPAPR machine, the O/S will obtain the page address of the ESB
entry associated with a source and its characteristic using the
H_INT_GET_SOURCE_INFO hcall. On PowerNV, a similar OPAL call is used.
The xive_source_notify() routine is in charge forwarding the source
event notification to the routing engine. It will be filled later on.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The OpenPIC have 5 outputs per connected CPU. The machine init code hence
needs a bi-dimensional array (smp_cpu lines, 5 columns) to wire up the irqs
between the PIC and the CPUs.
The current code first allocates an array of smp_cpus pointers to qemu_irq
type, then it allocates another array of smp_cpus * 5 qemu_irq and fills the
first array with pointers to each line of the second array. This is rather
convoluted.
Simplify the logic by introducing a structured type that describes all the
OpenPIC outputs for a single CPU, ie, fixed size of 5 qemu_irq, and only
allocate a smp_cpu sized array of those.
This also allows to use g_new(T, n) instead of g_malloc(sizeof(T) * n)
as recommended in HACKING.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The OpenPIC have 5 outputs per connected CPU. The machine init code hence
needs a bi-dimensional array (smp_cpu lines, 5 columns) to wire up the irqs
between the PIC and the CPUs.
The current code first allocates an array of smp_cpus pointers to qemu_irq
type, then it allocates another array of smp_cpus * 5 qemu_irq and fills the
first array with pointers to each line of the second array. This is rather
convoluted.
Simplify the logic by introducing a structured type that describes all the
OpenPIC outputs for a single CPU, ie, fixed size of 5 qemu_irq, and only
allocate a smp_cpu sized array of those.
This also allows to use g_new(T, n) instead of g_malloc(sizeof(T) * n)
as recommended in HACKING.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Because it is a recommended coding practice (see HACKING).
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Because it is a recommended coding practice (see HACKING).
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Because it is a recommended coding practice (see HACKING).
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Because it is a recommended coding practice (see HACKING).
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Because it is a recommended coding practice (see HACKING).
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Because it is a recommended coding practice (see HACKING).
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Laurent Vivier reported off by one with maximum number of NUMA nodes
provided by qemu-kvm being less by one than required according to
description of "ibm,max-associativity-domains" property in LoPAPR.
It appears that I incorrectly treated LoPAPR description of this
property assuming it provides last valid domain (NUMA node here)
instead of maximum number of domains.
### Before hot-add
(qemu) info numa
3 nodes
node 0 cpus: 0
node 0 size: 0 MB
node 0 plugged: 0 MB
node 1 cpus:
node 1 size: 1024 MB
node 1 plugged: 0 MB
node 2 cpus:
node 2 size: 0 MB
node 2 plugged: 0 MB
$ numactl -H
available: 2 nodes (0-1)
node 0 cpus: 0
node 0 size: 0 MB
node 0 free: 0 MB
node 1 cpus:
node 1 size: 999 MB
node 1 free: 658 MB
node distances:
node 0 1
0: 10 40
1: 40 10
### Hot-add
(qemu) object_add memory-backend-ram,id=mem0,size=1G
(qemu) device_add pc-dimm,id=dimm1,memdev=mem0,node=2
(qemu) [ 87.704898] pseries-hotplug-mem: Attempting to hot-add 4 ...
<there is no "Initmem setup node 2 [mem 0xHEX-0xHEX]">
[ 87.705128] lpar: Attempting to resize HPT to shift 21
... <HPT resize messages>
### After hot-add
(qemu) info numa
3 nodes
node 0 cpus: 0
node 0 size: 0 MB
node 0 plugged: 0 MB
node 1 cpus:
node 1 size: 1024 MB
node 1 plugged: 0 MB
node 2 cpus:
node 2 size: 1024 MB
node 2 plugged: 1024 MB
$ numactl -H
available: 2 nodes (0-1)
^^^^^^^^^^^^^^^^^^^^^^^^
Still only two nodes (and memory hot-added to node 0 below)
node 0 cpus: 0
node 0 size: 1024 MB
node 0 free: 1021 MB
node 1 cpus:
node 1 size: 999 MB
node 1 free: 658 MB
node distances:
node 0 1
0: 10 40
1: 40 10
After fix applied numactl(8) reports 3 nodes available and memory
plugged into node 2 as expected.
From David Gibson:
------------------
Qemu makes a distinction between "non NUMA" (nb_numa_nodes == 0) and
"NUMA with one node" (nb_numa_nodes == 1). But from a PAPR guests's
point of view these are equivalent. I don't want to present two
different cases to the guest when we don't need to, so even though the
guest can handle it, I'd prefer we put a '1' here for both the
nb_numa_nodes == 0 and nb_numa_nodes == 1 case.
This consolidates everything discussed previously on mailing list.
Fixes: da9f80fbad ("spapr: Add ibm,max-associativity-domains property")
Reported-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Serhii Popovych <spopovyc@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
The watermark bits are set in the interrupt pending register according
to the configuration of txcnt and rxcnt in the txctrl and rxctrl
registers.
Since the UART TX does not implement a FIFO, the txwm bit is set as long
as the TX watermark level is greater than zero.
Signed-off-by: Nathaniel Graff <nathaniel.graff@sifive.com>
Reviewed-by: Michael Clark <mjc@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Previously the second UARTs on the sifive_e and sifive_u machines
where disabled due to check-qtest-riscv32 and check-qtest-riscv64
failures. Recent changes in the QEMU core serial code have
resolved these failures so the second UARTs can be instantiated.
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Sagar Karandikar <sagark@eecs.berkeley.edu>
Cc: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Cc: Alistair Francis <Alistair.Francis@wdc.com>
Signed-off-by: Michael Clark <mjc@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The address calculation for the pending bitfield had
a copy paste bug. This bug went unnoticed because the Linux
PLIC driver does not read the pending bitfield, rather it
reads pending interrupt numbers from the claim register
and writes acknowledgements back to the claim register.
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Sagar Karandikar <sagark@eecs.berkeley.edu>
Cc: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Cc: Alistair Francis <Alistair.Francis@wdc.com>
Reported-by: Vincent Siles <vincent.siles@ens-lyon.org>
Signed-off-by: Michael Clark <mjc@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
A missing shift made updates to the low order bits
of timecmp erroneously copy the old low order bits
into the high order bits of the 64-bit timecmp
register. Add the missing shift and rename timecmp
local variables to timecmp_hi and timecmp_lo.
This bug didn't show up as the low order bits are
usually written first followed by the high order
bits meaning the high order bits contained an invalid
value between the timecmp_lo and timecmp_hi update.
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Sagar Karandikar <sagark@eecs.berkeley.edu>
Cc: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Cc: Alistair Francis <Alistair.Francis@wdc.com>
Co-Authored-by: Johannes Haring <johannes.haring@gmx.net>
Signed-off-by: Michael Clark <mjc@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
The 'clock-frequency' DT property is required by U-Boot to compute
the divider value. This patch sets the 'clock-frequency' DT property
of the SiFive UART device tree node (similar to virt machine).
Signed-off-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Connect the gpex PCIe device based on the device tree included in the
HiFive Unleashed ROM.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Andrea Bolognani <abologna@redhat.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
When the user didn't specify "intremap" for the IOMMU device, we turn
it on by default if it is supported. This will turn IR on for the
default Q35 platform as long as the IOMMU device is specified on new
kernels.
Signed-off-by: Peter Xu <peterx@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Switch the intr_supported variable from a boolean to OnOffAuto type so
that we can know whether the user specified it or not. With that
we'll have a chance to help the user to choose more wisely where
possible. Introduce x86_iommu_ir_supported() to mask these changes.
No functional change at all.
Signed-off-by: Peter Xu <peterx@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Starting from QEMU 4.0, let's specify "split" as the default value for
kernel-irqchip.
So for QEMU>=4.0 we'll have: allowed=Y,required=N,split=Y
for QEMU<=3.1 we'll have: allowed=Y,required=N,split=N
(omitting all the "kernel_irqchip_" prefix)
Note that this will let the default q35 machine type to depend on
Linux version 4.4 or newer because that's where split irqchip is
introduced in kernel. But it's fine since we're boosting supported
Linux version for QEMU 4.0 to around Linux 4.5. For more information
please refer to the discussion on AMD's RDTSCP:
https://lore.kernel.org/lkml/20181210181328.GA762@zn.tnic/
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
A conventional PCI bus does not support config space accesses above
the standard 256 byte configuration space. PCIe-to-PCI bridges are
not permitted to forward transactions if the extended register address
field is non-zero and must handle it as an unsupported request (PCIe
bridge spec rev 1.0, 4.1.3, 4.1.4). Therefore, we should not support
extended config space if there is a conventional bus anywhere on the
path to a device.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Introduce and use the "unplug" callback.
This is a preparation for multi-stage hotplug handlers, whereby the bus
hotplug handler is overwritten by the machine hotplug handler. This handler
will then pass control to the bus hotplug handler. So to get this running
cleanly, we also have to make sure to go via the hotplug handler chain when
actually unplugging a device after an unplug request. Lookup the hotplug
handler and call "unplug".
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Introduce and use the "unplug" callback.
This is a preparation for multi-stage hotplug handlers, whereby the bus
hotplug handler is overwritten by the machine hotplug handler. This handler
will then pass control to the bus hotplug handler. So to get this running
cleanly, we also have to make sure to go via the hotplug handler chain when
actually unplugging a device after an unplug request. Lookup the hotplug
handler and call "unplug".
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
These functions are essentially the same, we only have to use
object_get_typename() for reporting errors. So let's share the
implementation of hotplug handler callbacks.
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Introduce and use the "unplug" callback.
This is a preparation for multi-stage hotplug handlers, whereby the bus
hotplug handler is overwritten by the machine hotplug handler. This handler
will then pass control to the bus hotplug handler. So to get this running
cleanly, we also have to make sure to go via the hotplug handler chain when
actually unplugging a device after an unplug request. Lookup the hotplug
handler and call "unplug".
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Introduce and use the "unplug" callback.
This is a preparation for multi-stage hotplug handlers, whereby the bus
hotplug handler is overwritten by the machine hotplug handler. This handler
will then pass control to the bus hotplug handler. So to get this running
cleanly, we also have to make sure to go via the hotplug handler chain when
actually unplugging a device after an unplug request. Lookup the hotplug
handler and call "unplug".
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
For now, the hotplug handler is not called for devices that are
being cold plugged. The hotplug handler is setup when the machine
initialization is fully done. Only bridges that were cold plugged are
considered.
Set the hotplug handler for the root piix bus directly when realizing.
Overwrite the hotplug handler of bridges when coldplugging them.
This will now make sure that the ACPI PCI hotplug handler is also called
for cold plugged devices (also on bridges) but not for bridges that were
hotplugged (keeping the current behavior).
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Perform the check in the pre_plug handler. In addition, we need the
capability only if the device is actually hotplugged (and not created
during machine initialization). This is a preparation for coldplugging
pci devices via that hotplug handler.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The callbacks are also called for cold plugged devices. Drop the "hot"
to better match the actual callback names.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Pierre Morel<pmorel@linux.ibm.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The callbacks are also called for cold plugged devices. Drop the "hot"
to better match the actual callback names.
While at it, also rename shpc_device_hotplug_common() to
shpc_device_plug_common().
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The callbacks are also called for cold plugged devices. Drop the "hot"
to better match the actual callback names.
While at it, also rename pcie_cap_slot_hotplug_common() to
pcie_cap_slot_plug_common().
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
They've been deprecated for two releases and nobody complained that they
are still required anymore, so it's time to remove these now.
And while we're at it, mark the other remaining old 0.x machine types
as deprecated (since they can not properly be used for live-migration
anyway).
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Taking the address of a field in a packed struct is a bad idea, because
it might not be actually aligned enough for that pointer type (and
thus cause a crash on dereference on some host architectures). Newer
versions of clang warn about this.
Avoid the problem by using local copies of the PMCW and SCSW
struct fields in copy_schib_from_guest() and copy_schib_to_guest().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20181213120252.21697-1-peter.maydell@linaro.org>
Reviewed-by: Farhan Ali <alifm@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes, with the changes
to the following files manually reverted:
contrib/libvhost-user/libvhost-user-glib.h
contrib/libvhost-user/libvhost-user.c
contrib/libvhost-user/libvhost-user.h
linux-user/mips64/cpu_loop.c
linux-user/mips64/signal.c
linux-user/sparc64/cpu_loop.c
linux-user/sparc64/signal.c
linux-user/x86_64/cpu_loop.c
linux-user/x86_64/signal.c
target/s390x/gen-features.c
tests/migration/s390x/a-b-bios.c
tests/test-rcu-simpleq.c
tests/test-rcu-tailq.c
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20181204172535.2799-1-armbru@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
Acked-by: Halil Pasic <pasic@linux.ibm.com>
Acked-by: Yuval Shaia <yuval.shaia@oracle.com>
Acked-by: Viktor Prutyanov <viktor.prutyanov@phystech.edu>
Now that build_rsdp() supports building both legacy and current RSDP
tables, we can move it to a generic folder (hw/acpi) and have the i386
ACPI code reuse it in order to reduce code duplication.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
We add the ability to build legacy or current RSDP tables, based on the
AcpiRsdpData revision field passed to build_rsdp().
Although arm/virt only uses RSDP v2, adding that capability to
build_rsdp will allow us to share the RSDP build code between ARM and x86.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Instead of filling a mapped and packed C structure field in random order
and being careful about endianness and sizes, build_rsdp() now uses
build_append_int_noprefix() to compose RSDP table.
This makes reviewing and maintaining code easier as this is almost
matching 1:1 the ACPI spec itself.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
That will allow us to generalize the ARM build_rsdp() routine to support
both legacy RSDP (The current i386 implementation) and extended RSDP
(The ARM implementation).
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
AcpiRsdpDescriptor describes revision 2 RSDP table so using sizeof(*rsdp)
for checksum calculation isn't correct since we are adding extra 16 bytes.
But acpi_data_push() zeroes out table, so just by luck we are summing up
exta zeros which still yelds correct checksum.
Fix it up by explicitly stating table size instead of using
pointer arithmetics on stucture.
PS:
Extra 16 bytes are still wasted, but droping them will break migration
for machines older than 2.3 due to size mismatch, for 2.3 and older it's
not an issue since they are using resizable memory regions (a1666142d)
for ACPI blobs. So keep wasting memory to avoid breaking old machines.
Fixes: 72c194f7e (i386: ACPI table generation code from seabios)
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When RSDP table was introduced (d4bec5d87), we calculated only legacy
checksum, and that was incorrect as it
- specified rev=2 and forgot about extended checksum.
- legacy checksum calculated on full table instead of the 1st 20 bytes
Fix it by adding extended checksum calculation and using correct
size for legacy checksum.
While at it use explicit constants to specify sub/full tables
sizes instead of relying on AcpiRsdpDescriptor size and fields offsets.
The follow up commits will convert this table to build_append_int_noprefix() API,
will use constants anyway and remove unused AcpiRsdpDescriptor structure.
Based on "[PATCH v5 05/24] hw: acpi: Implement XSDT support for RSDP"
by Samuel Ortiz, who did it right in his impl.
Fixes: d4bec5d87 ("hw/arm/virt-acpi-build: Generate RSDP table")
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
CC: Ard Biesheuvel <ard.biesheuvel@linaro.org>
CC: Shannon Zhao <shannon.zhaosl@gmail.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
For both x86 and ARM architectures, the internal RSDP build API can
return void as the current return value is unused.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We're going to have 57bits aw-bits support sooner. It's possibly time
to remove the "x-" prefix.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Support DMA read/write draining should be easy for existing VT-d
emulation since the emulation itself does not have any request queue
there so we don't need to do anything to flush the un-commited queue.
What we need to do is to declare the support.
These capabilities are required to pass Windows SVVP test program. It
is verified that when with parameters "x-aw-bits=48,caching-mode=off"
we can pass the Windows SVVP test with this patch applied. Otherwise
we'll fail with:
IOMMU[0] - DWD (DMA write draining) not supported
IOMMU[0] - DWD (DMA read draining) not supported
Segment 0 has no DMA remapping capable IOMMU units
However since these bits are not declared support for QEMU<=3.1, we'll
need a compatibility bit for it and we turn this on by default only
for QEMU>=4.0.
Please refer to VT-d spec 6.5.4 for more information.
CC: Yu Wang <wyu@redhat.com>
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1654550
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Report more *_invalid() tracepoints to error_report_once() so that we
can detect issues even without tracing enabled. Drop those tracepoints.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The iotlb.iova can be zero if failure really happened. Dump the addr
instead.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Change the default speed and width for new machine types to the
fastest and widest currently supported. This should be compatible to
the PCIe 4.0 spec. Pre-QEMU-4.0 machine types remain at 2.5GT/s, x1
width.
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Now that the downstream port will virtually negotiate itself to the
link status of the downstream device, we can remove this emulation.
It's not clear that it was every terribly useful anyway.
Tested-by: Geoffrey McRae <geoff@hostfission.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Allow users to experimentally specify speed and width values for the
generic PCIe root port. Defaults remain at 2.5GT/s & x1 for
compatiblity with the intent to only support changing defaults via
machine types for now.
Note for libvirt testing that pcie-root-port controllers are given
default names like "pci.7" which don't play well with using the
"-set device.$name.$prop=$value" options accessible to us via
<qemu:commandline> options. The solution is to add an <alias> to the
pcie-root-port <controller>, for example:
<controller type='pci' index='7' model='pcie-root-port'>
<model name='pcie-root-port'/>
<target chassis='7' port='0x15'/>
<alias name='ua-gfx0'/>
<address type='pci' domain='0x0000' bus='0x00' slot='0x02' function='0x5'/>
</controller>
The "ua-" here is a mandatory prefix. We can then use:
<qemu:commandline>
<qemu:arg value='-set'/>
<qemu:arg value='device.ua-gfx0.x-speed=8'/>
<qemu:arg value='-set'/>
<qemu:arg value='device.ua-gfx0.x-width=16'/>
</qemu:commandline>
or, without an alias, set globals such as:
<qemu:commandline>
<qemu:arg value='-global'/>
<qemu:arg value='pcie-root-port.x-speed=8'/>
<qemu:arg value='-global'/>
<qemu:arg value='pcie-root-port.x-width=16'/>
</qemu:commandline>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Tested-by: Geoffrey McRae <geoff@hostfission.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Make use of the PCIESlot speed and width fields to update link
information beyond those configured in pcie_cap_v1_fill(). This is
only called for devices supporting a version 2 capability and
automatically skips any non-PCIESlot devices. Only devices with
increased link values generate any visible config space differences.
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Tested-by: Geoffrey McRae <geoff@hostfission.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add fields allowing the PCIe link speed and width of a PCIESlot to
be configured, with an instance_post_init callback on the root port
parent class to set defaults. This allows child classes to set these
via properties or via their own instance_init callback, without
requiring all implementions to support arbitrary user selected values.
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Tested-by: Geoffrey McRae <geoff@hostfission.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Create properties to be able to define speeds and widths for PCIe
links. The only tricky bit here is that our get and set callbacks
translate from the fixed QAPI automagic enums to those we define
in PCI code to represent the actual register segment value.
Cc: Eric Blake <eblake@redhat.com>
Tested-by: Geoffrey McRae <geoff@hostfission.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The PCIe link speed and width between a downstream device and its
upstream port is negotiated on real hardware and susceptible to
dynamic changes due to signal issues and power management. In the
emulated device case there is no real hardware link, but we still
might wish to have some consistency between endpoint and downstream
port via a virtual negotiation. There is of course a real link for
assigned devices and this same virtual negotiation allows the
downstream port to match the endpoint, synchronizing on every read
to support underlying physical hardware dynamically adjusting the
link.
This negotiation is intentionally unidirectional for compatibility.
If the endpoint exceeds the capabilities of the downstream port or
there is no endpoint device, the downstream port reports negotiation
to its maximum speed and width, matching the previous case where
negotiation was absent. De-tuning the endpoint to match a virtual
link doesn't seem to benefit anyone and is a condition we've thus
far reported without functional issues.
Note that PCI_EXP_LNKSTA is already ignored for migration
compatibility via pcie_cap_v1_fill().
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Tested-by: Geoffrey McRae <geoff@hostfission.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In preparation for reporting higher virtual link speeds and widths,
create enums and macros to help us manage them.
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Tested-by: Geoffrey McRae <geoff@hostfission.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When loadvm'ing a *running* snapshot qemu crashes due to an invalid
free. It's fortunately caught early by glibc heap memory corruption
protection and qemu gets killed with SIGABRT.
Steps to reproduce:
1) Create VM (e.g w/ virsh define)
2) Start the VM and take a snapshot while it's running and having a
PCI bridge attached
3) Destroy the VM and revert the running snapshot.
This commit fixes the issue.
Signed-off-by: Matthias Weckbecker <matthias@weckbecker.name>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
SMBIOS is just another firmware interface used by some QEMU models.
We will later introduce more firmware interfaces in this subdirectory.
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This header only declare a single function: smbios_build_type_38_table().
We already have a header that declares such functions: "smbios_build.h".
Move the declaration and remove the header.
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
All the consumers of "hw/smbios/ipmi.h" are located in hw/smbios/.
There is no need to have this include publicly exposed,
reduce the visibility by moving it in hw/smbios/.
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Many of the current virtio-*-pci device types actually represent
3 different types of devices:
* virtio 1.0 non-transitional devices
* virtio 1.0 transitional devices
* virtio 0.9 ("legacy device" in virtio 1.0 terminology)
That would be just an annoyance if it didn't break our device/bus
compatibility QMP interfaces. With these multi-purpose device
types, there's no way to tell management software that
transitional devices and legacy devices require a Conventional
PCI bus.
The multi-purpose device types would also prevent us from telling
management software what's the PCI vendor/device ID for them,
because their PCI IDs change at runtime depending on the bus
where they were plugged.
This patch adds separate device types for each of those virtio
device flavors:
- virtio-*-pci: the existing multi-purpose device types
- Configurable using `disable-legacy` and `disable-modern`
properties
- Legacy driver support is automatically enabled/disabled
depending on the bus where it is plugged
- Supports Conventional PCI and PCI Express buses
(but Conventional PCI is incompatible with
disable-legacy=off)
- Changes PCI vendor/device IDs at runtime
- virtio-*-pci-transitional: virtio-1.0 device supporting legacy drivers
- Supports Conventional PCI buses only, because
it has a PIO BAR
- virtio-*-pci-non-transitional: modern-only
- Supports both Conventional PCI and PCI Express buses
The existing TYPE_* macros for these types will point to an
abstract base type, so existing casts in the code will keep
working for all variants.
A simple test script (tests/acceptance/virtio_version.py) is
included, to check if the new device types are equivalent to
using the `disable-legacy` and `disable-modern` options.
Acked-by: Andrea Bolognani <abologna@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Introduce a helper for registering different flavours of virtio
devices. Convert code to use the helper, but keep only the
existing generic types. Transitional and non-transitional device
types will be added by another patch.
Acked-by: Andrea Bolognani <abologna@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Otherwise it won't be set up correctly and won't work after
miigration.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: qemu-stable@nongnu.org
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When VM boots from the latest version of linux kernel, after
hot-unpluging virtio-blk disks which are hotplugged into
pcie-root-port, the VM's dmesg log shows:
[ 151.046242] pciehp 0000:00:05.0:pcie004: pending interrupts 0x0001 from Slot Status
[ 151.046365] pciehp 0000:00:05.0:pcie004: Slot(0-3): Attention button pressed
[ 151.046369] pciehp 0000:00:05.0:pcie004: Slot(0-3): Powering off due to button press
[ 151.046420] pciehp 0000:00:05.0:pcie004: pending interrupts 0x0010 from Slot Status
[ 151.046425] pciehp 0000:00:05.0:pcie004: pciehp_green_led_blink: SLOTCTRL a8 write cmd 200
[ 151.046464] pciehp 0000:00:05.0:pcie004: pending interrupts 0x0010 from Slot Status
[ 151.046468] pciehp 0000:00:05.0:pcie004: pciehp_set_attention_status: SLOTCTRL a8 write cmd c0
[ 156.163421] pciehp 0000:00:05.0:pcie004: pciehp_get_power_status: SLOTCTRL a8 value read 2f1
[ 156.163427] pciehp 0000:00:05.0:pcie004: pciehp_unconfigure_device: domain🚌dev = 0000:06:00
[ 156.198736] pciehp 0000:00:05.0:pcie004: pending interrupts 0x0010 from Slot Status
[ 156.198772] pciehp 0000:00:05.0:pcie004: pciehp_power_off_slot: SLOTCTRL a8 write cmd 400
[ 157.224124] pciehp 0000:00:05.0:pcie004: pending interrupts 0x0018 from Slot Status
[ 157.224194] pciehp 0000:00:05.0:pcie004: pciehp_green_led_off: SLOTCTRL a8 write cmd 300
[ 157.224220] pciehp 0000:00:05.0:pcie004: pciehp_check_link_active: lnk_status = 2011
[ 157.224223] pciehp 0000:00:05.0:pcie004: Slot(0-3): Link Up
[ 157.224233] pciehp 0000:00:05.0:pcie004: pciehp_get_power_status: SLOTCTRL a8 value read 7f1
[ 157.224281] pciehp 0000:00:05.0:pcie004: pending interrupts 0x0010 from Slot Status
[ 157.224285] pciehp 0000:00:05.0:pcie004: pciehp_power_on_slot: SLOTCTRL a8 write cmd 0
[ 157.224300] pciehp 0000:00:05.0:pcie004: __pciehp_link_set: lnk_ctrl = 0
[ 157.224336] pciehp 0000:00:05.0:pcie004: pending interrupts 0x0010 from Slot Status
[ 157.224339] pciehp 0000:00:05.0:pcie004: pciehp_green_led_blink: SLOTCTRL a8 write cmd 200
[ 159.739294] pci 0000:06:00.0 id reading try 50 times with interval 20 ms to get ffffffff
[ 159.739315] pciehp 0000:00:05.0:pcie004: pciehp_check_link_status: lnk_status = 2011
[ 159.739318] pciehp 0000:00:05.0:pcie004: Failed to check link status
[ 159.739371] pciehp 0000:00:05.0:pcie004: pending interrupts 0x0010 from Slot Status
[ 159.739394] pciehp 0000:00:05.0:pcie004: pciehp_power_off_slot: SLOTCTRL a8 write cmd 400
[ 160.771426] pciehp 0000:00:05.0:pcie004: pending interrupts 0x0010 from Slot Status
[ 160.771452] pciehp 0000:00:05.0:pcie004: pciehp_green_led_off: SLOTCTRL a8 write cmd 300
[ 160.771495] pciehp 0000:00:05.0:pcie004: pending interrupts 0x0010 from Slot Status
[ 160.771499] pciehp 0000:00:05.0:pcie004: pciehp_set_attention_status: SLOTCTRL a8 write cmd 40
[ 160.771535] pciehp 0000:00:05.0:pcie004: pending interrupts 0x0010 from Slot Status
[ 160.771539] pciehp 0000:00:05.0:pcie004: pciehp_green_led_off: SLOTCTRL a8 write cmd 300
After analyzing the log information, it seems that qemu doesn't
change the Link Status from active to inactive after hot-unplug.
This results in the abnormal log after the linux kernel commit
d331710ea78fea merged.
Furthermore, If I hotplug the same virtio-blk disk after hot-unplug,
the virtio-blk would turn on and then back off.
So this patch set the Link Status inactive after hot-unplug and
active after hot-plug.
Signed-off-by: Zheng Xiang <zhengxiang9@huawei.com>
Signed-off-by: Zheng Xiang <xiang.zheng@linaro.org>
Cc: Wang Haibin <wanghaibin.wang@huawei.com>
Cc: qemu-stable@nongnu.org
Reviewed-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The qmp/hmp command 'system_wakeup' is simply a direct call to
'qemu_system_wakeup_request' from vl.c. This function verifies if
runstate is SUSPENDED and if the wake up reason is valid before
proceeding. However, no error or warning is thrown if any of those
pre-requirements isn't met. There is no way for the caller to
differentiate between a successful wakeup or an error state caused
when trying to wake up a guest that wasn't suspended.
This means that system_wakeup is silently failing, which can be
considered a bug. Adding error handling isn't an API break in this
case - applications that didn't check the result will remain broken,
the ones that check it will have a chance to deal with it.
Adding to that, the commit before previous created a new QMP API called
query-current-machine, with a new flag called wakeup-suspend-support,
that indicates if the guest has the capability of waking up from suspended
state. Although such guest will never reach SUSPENDED state and erroring
it out in this scenario would suffice, it is more informative for the user
to differentiate between a failure because the guest isn't suspended versus
a failure because the guest does not have support for wake up at all.
All this considered, this patch changes qmp_system_wakeup to check if
the guest is capable of waking up from suspend, and if it is suspended.
After this patch, this is the output of system_wakeup in a guest that
does not have wake-up from suspend support (ppc64):
(qemu) system_wakeup
wake-up from suspend is not supported by this guest
(qemu)
And this is the output of system_wakeup in a x86 guest that has the
support but isn't suspended:
(qemu) system_wakeup
Unable to wake up: guest is not in suspended state
(qemu)
Reported-by: Balamuruhan S <bala24@linux.vnet.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20181205194701.17836-4-danielhb413@gmail.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
When issuing the qmp/hmp 'system_wakeup' command, what happens in a
nutshell is:
- qmp_system_wakeup_request set runstate to RUNNING, sets a wakeup_reason
and notify the event
- in the main_loop, all vcpus are paused, a system reset is issued, all
subscribers of wakeup_notifiers receives a notification, vcpus are then
resumed and the wake up QAPI event is fired
Note that this procedure alone doesn't ensure that the guest will awake
from SUSPENDED state - the subscribers of the wake up event must take
action to resume the guest, otherwise the guest will simply reboot. At
this moment, only the ACPI machines via acpi_pm1_cnt_init and xen_hvm_init
have wake-up from suspend support.
However, only the presence of 'system_wakeup' is required for QGA to
support 'guest-suspend-ram' and 'guest-suspend-hybrid' at this moment.
This means that the user/management will expect to suspend the guest using
one of those suspend commands and then resume execution using system_wakeup,
regardless of the support offered in system_wakeup in the first place.
This patch creates a new API called query-current-machine [1], that holds
a new flag called 'wakeup-suspend-support' that indicates if the guest
supports wake up from suspend via system_wakeup. The machine is considered
to implement wake-up support if a call to a new 'qemu_register_wakeup_support'
is made during its init, as it is now being done inside acpi_pm1_cnt_init
and xen_hvm_init. This allows for any other machine type to declare wake-up
support regardless of ACPI state or wakeup_notifiers subscription, making easier
for newer implementations that might have their own mechanisms in the future.
This is the expected output of query-current-machine when running a x86
guest:
{"execute" : "query-current-machine"}
{"return": {"wakeup-suspend-support": true}}
Running the same x86 guest, but with the --no-acpi option:
{"execute" : "query-current-machine"}
{"return": {"wakeup-suspend-support": false}}
This is the output when running a pseries guest:
{"execute" : "query-current-machine"}
{"return": {"wakeup-suspend-support": false}}
With this extra tool, management can avoid situations where a guest
that does not have proper suspend/wake capabilities ends up in
inconsistent state (e.g.
https://github.com/open-power-host-os/qemu/issues/31).
[1] the decision of creating the query-current-machine API is based
on discussions in the QEMU mailing list where it was decided that
query-target wasn't a proper place to store the wake-up flag, neither
was query-machines because this isn't a static property of the
machine object. This new API can then be used to store other
dynamic machine properties that are scattered around the code
ATM. More info at:
https://lists.gnu.org/archive/html/qemu-devel/2018-05/msg04235.html
Reported-by: Balamuruhan S <bala24@linux.vnet.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20181205194701.17836-2-danielhb413@gmail.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
backend.
-----BEGIN PGP SIGNATURE-----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=toR4
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/gkurz/tags/for-upstream' into staging
Most notable change in this PR is the full removal of the "handle" fsdev
backend.
# gpg: Signature made Wed 12 Dec 2018 13:20:42 GMT
# gpg: using RSA key 71D4D5E5822F73D6
# gpg: Good signature from "Greg Kurz <groug@kaod.org>"
# gpg: aka "Gregory Kurz <gregory.kurz@free.fr>"
# gpg: aka "[jpeg image of size 3330]"
# Primary key fingerprint: B482 8BAF 9431 40CE F2A3 4910 71D4 D5E5 822F 73D6
* remotes/gkurz/tags/for-upstream:
9p: remove support for the "handle" backend
xen/9pfs: use g_new(T, n) instead of g_malloc(sizeof(T) * n)
9p: use g_new(T, n) instead of g_malloc(sizeof(T) * n)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Convert various devices from sysbus init to instance_init
* Remove the now unused sysbus init support entirely
* Allow AArch64 processors to boot from a kernel placed over 4GB
* hw: arm: musicpal: drop TYPE_WM8750 in object_property_set_link()
* versal: minor fixes to virtio-mmio instantation
* arm: Implement the ARMv8.1-HPD extension
* arm: Implement the ARMv8.2-AA32HPD extension
* arm: Implement the ARMv8.1-LOR extension (as the trivial
"no limited ordering regions provided" minimum)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=fIbS
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20181213' into staging
target-arm queue:
* Convert various devices from sysbus init to instance_init
* Remove the now unused sysbus init support entirely
* Allow AArch64 processors to boot from a kernel placed over 4GB
* hw: arm: musicpal: drop TYPE_WM8750 in object_property_set_link()
* versal: minor fixes to virtio-mmio instantation
* arm: Implement the ARMv8.1-HPD extension
* arm: Implement the ARMv8.2-AA32HPD extension
* arm: Implement the ARMv8.1-LOR extension (as the trivial
"no limited ordering regions provided" minimum)
# gpg: Signature made Thu 13 Dec 2018 14:52:25 GMT
# gpg: using RSA key 3C2525ED14360CDE
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>"
# gpg: aka "Peter Maydell <pmaydell@gmail.com>"
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>"
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20181213: (37 commits)
target/arm: Implement the ARMv8.1-LOR extension
target/arm: Use arm_hcr_el2_eff more places
target/arm: Introduce arm_hcr_el2_eff
target/arm: Implement the ARMv8.2-AA32HPD extension
target/arm: Implement the ARMv8.1-HPD extension
target/arm: Tidy scr_write
target/arm: Fix HCR_EL2.TGE check in arm_phys_excp_target_el
target/arm: Add SCR_EL3 bits up to ARMv8.5
target/arm: Add HCR_EL2 bits up to ARMv8.5
target/arm: Move id_aa64mmfr* to ARMISARegisters
hw/arm: versal: Correct the nr of IRQs to 192
hw/arm: versal: Use IRQs 111 - 118 for virtio-mmio
hw/arm: versal: Reduce number of virtio-mmio instances
hw/arm: versal: Remove bogus virtio-mmio creation
core/sysbus: remove the SysBusDeviceClass::init path
xen_backend: remove xen_sysdev_init() function
usb/tusb6010: Convert sysbus init function to realize function
timer/puv3_ost: Convert sysbus init function to realize function
timer/grlib_gptimer: Convert sysbus init function to realize function
timer/etraxfs_timer: Convert sysbus init function to realize function
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
I introduced indentation using tabs instead of spaces in another
commit. Peter reported the problem, and I failed to fix that
before sending my pull request.
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20181212003147.29604-1-ehabkost@redhat.com
Fixes: 9515976076 ("virt: Eliminate separate instance_init functions")
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In sdhci_sysbus_realize() we override the initialization of
s->iomem that sdhci_common_realize() performs. However we
don't destroy the old memory region before reinitializing
it, which means that the memory allocated for mr->name in
memory_region_do_init() is leaked.
Since sdhci_initfn() already initializes s->io_ops to
&sdhci_mmio_ops, always use that in sdhci_common_realize()
and remove the now-unnecessary reinitialization of the
MMIO region from sdhci_sysbus_realize().
Spotted by clang's leak sanitizer.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20181204132952.2601-4-peter.maydell@linaro.org
The clang leak sanitizer spots a (one-off, trivial) memory
leak in make_dma() due to a missing free.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20181204132952.2601-3-peter.maydell@linaro.org
The load_image() function is now no longer used anywhere, so
we can remove it completely. (Use load_image_size() or
g_file_get_contents() instead.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20181130151712.2312-10-peter.maydell@linaro.org
The load_image() function is deprecated, as it does not let the
caller specify how large the buffer to read the file into is.
Instead use load_image_size().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20181130151712.2312-8-peter.maydell@linaro.org
The load_image() function is deprecated, as it does not let the
caller specify how large the buffer to read the file into is.
Instead use load_image_size().
While we are converting the code, add the missing error check.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20181130151712.2312-7-peter.maydell@linaro.org
The load_image() function is deprecated, as it does not let the
caller specify how large the buffer to read the file into is.
Use the glib g_file_get_contents() function instead, which does
the whole "allocate memory for the file and read it in" operation.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20181130151712.2312-6-peter.maydell@linaro.org
The load_image() function is deprecated, as it does not let the
caller specify how large the buffer to read the file into is.
Instead use load_image_size().
While we are converting this code, add an error-check
for read failure.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20181130151712.2312-5-peter.maydell@linaro.org
The load_image() function is deprecated, as it does not let the
caller specify how large the buffer to read the file into is.
Instead use load_image_size().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 20181130151712.2312-4-peter.maydell@linaro.org
The load_image() function is deprecated, as it does not let the
caller specify how large the buffer to read the file into is.
Instead use load_image_size().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Message-id: 20181130151712.2312-3-peter.maydell@linaro.org
The load_image() function is deprecated, as it does not let the
caller specify how large the buffer to read the file into is.
Use the glib g_file_get_contents() function instead, which does
the whole "allocate memory for the file and read it in" operation.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Message-id: 20181130151712.2312-2-peter.maydell@linaro.org
The API of cpu_physical_memory_write_rom() is odd, because it
takes an AddressSpace, unlike all the other cpu_physical_memory_*
access functions. Rename it to address_space_write_rom(), and
bring its API into line with address_space_write().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 20181122133507.30950-3-peter.maydell@linaro.org
The filename length in MTP metadata is specified by the guest. By
trusting it directly it'd theoretically be possible to get the host to
write memory parts outside the filename buffer into a filename. In
practice though there are usually NUL bytes stopping the string
operations.
Also use the opportunity to not assign the filename member twice.
Signed-off-by: Michael Hanselmann <public@hansmi.ch>
Message-id: ab70659d8d5c580bdf150a5f7d5cc60c8e374ffc.1544740018.git.public@hansmi.ch
[ kraxel: codestyle fix: break a long line ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Open files and directories with O_NOFOLLOW to avoid symlinks attacks.
While being at it also add O_CLOEXEC.
usb-mtp only handles regular files and directories and ignores
everything else, so users should not see a difference.
Because qemu ignores symlinks, carrying out a successful symlink attack
requires swapping an existing file or directory below rootdir for a
symlink and winning the race against the inotify notification to qemu.
Fixes: CVE-2018-16872
Cc: Prasad J Pandit <ppandit@redhat.com>
Cc: Bandan Das <bsd@redhat.com>
Reported-by: Michael Hanselmann <public@hansmi.ch>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Michael Hanselmann <public@hansmi.ch>
Message-id: 20181213122511.13853-1-kraxel@redhat.com
Replace arm_hcr_el2_{fmo,imo,amo} with a more general routine
that also takes SCR_EL3.NS (aka arm_is_secure_below_el3) into
account, as documented for the plethora of bits in HCR_EL2.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20181210150501.7990-2-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use IRQs 111 - 118 for virtio-mmio. The interrupts we're currently
using 160+ are not available in the Versal GIC.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20181129163655.20370-4-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reduce number of virtio-mmio instances. This is in preparation
for correcting the interrupt setup for Versal.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20181129163655.20370-3-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Remove bogus virtio-mmio creation. This was an accidental
left-over an experiment.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-id: 20181129163655.20370-2-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use DeviceClass rather than SysBusDeviceClass in
tusb6010_class_init().
Cc: kraxel@redhat.com
Signed-off-by: Mao Zhongyi <maozhongyi@cmss.chinamobile.com>
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Message-id: 20181130093852.20739-20-maozhongyi@cmss.chinamobile.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use DeviceClass rather than SysBusDeviceClass in
puv3_ost_class_init().
Cc: gxt@mprc.pku.edu.cn
Signed-off-by: Mao Zhongyi <maozhongyi@cmss.chinamobile.com>
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20181130093852.20739-19-maozhongyi@cmss.chinamobile.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use DeviceClass rather than SysBusDeviceClass in
grlib_gptimer_class_init().
Cc: chouteau@adacore.com
Signed-off-by: Mao Zhongyi <maozhongyi@cmss.chinamobile.com>
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20181130093852.20739-18-maozhongyi@cmss.chinamobile.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use DeviceClass rather than SysBusDeviceClass in
etraxfs_timer_class_init().
Cc: edgar.iglesias@gmail.com
Signed-off-by: Mao Zhongyi <maozhongyi@cmss.chinamobile.com>
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20181130093852.20739-17-maozhongyi@cmss.chinamobile.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use DeviceClass rather than SysBusDeviceClass in
nvram_sysbus_class_init().
Cc: pbonzini@redhat.com
Cc: marcandre.lureau@redhat.com
Signed-off-by: Mao Zhongyi <maozhongyi@cmss.chinamobile.com>
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20181130093852.20739-15-maozhongyi@cmss.chinamobile.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use DeviceClass rather than SysBusDeviceClass in
puv3_pm_class_init().
Cc: gxt@mprc.pku.edu.cn
Signed-off-by: Mao Zhongyi <maozhongyi@cmss.chinamobile.com>
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20181130093852.20739-14-maozhongyi@cmss.chinamobile.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use DeviceClass rather than SysBusDeviceClass in
milkymist_pfpu_class_init().
Cc: michael@walle.cc
Signed-off-by: Mao Zhongyi <maozhongyi@cmss.chinamobile.com>
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20181130093852.20739-13-maozhongyi@cmss.chinamobile.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use DeviceClass rather than SysBusDeviceClass in
milkymist_hpdmc_class_init().
Cc: gxt@mprc.pku.edu.cn
Cc: michael@walle.cc
Signed-off-by: Mao Zhongyi <maozhongyi@cmss.chinamobile.com>
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20181130093852.20739-12-maozhongyi@cmss.chinamobile.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Peter Maydell
Steffen Görtz
Philippe Mathieu-Daudé
Edgar E. Iglesias
Stefan Hajnoczi
Luc Michel
Daniel P. Berrangé
Marc-André Lureau
Li Qiang
Prasad J Pandit
Yuval Shaia
Cédric Le Goater
Alexey Kardashevskiy
Greg Kurz
Serhii Popovych
Nathaniel Graff
Michael Clark
Anup Patel
Alistair Francis
Peter Xu
Alex Williamson
David Hildenbrand
Thomas Huth
Markus Armbruster
Samuel Ortiz
Igor Mammedov
Matthias Weckbecker
Philippe Mathieu-Daudé
Eduardo Habkost
Corey Minyard
Zheng Xiang
Daniel Henrique Barboza
Michael Hanselmann
Gerd Hoffmann
Richard Henderson
Mao Zhongyi