Enable SVQ with VIRTIO_NET_F_CTRL_RX feature.
Signed-off-by: Hawkins Jiawei <yin31149@gmail.com>
Acked-by: Eugenio Pérez <eperezma@redhat.com>
Message-Id: <5d6173a6d7c4c514c98362b404c019f52d73b06c.1688743107.git.yin31149@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Due to the size limitation of the out buffer sent to the vdpa device,
which is determined by vhost_vdpa_net_cvq_cmd_len(), excessive CVQ
command is truncated in QEMU. As a result, the vdpa device rejects
this flawd CVQ command.
However, the problem is that, the VIRTIO_NET_CTRL_MAC_TABLE_SET
CVQ command has a variable length, which may exceed
vhost_vdpa_net_cvq_cmd_len() if the guest sets more than
`MAC_TABLE_ENTRIES` MAC addresses for the filter table.
This patch solves this problem by following steps:
* Increase the out buffer size to vhost_vdpa_net_cvq_cmd_page_len(),
which represents the size of the buffer that is allocated and mmaped.
This ensures that everything works correctly as long as the guest
sets fewer than `(vhost_vdpa_net_cvq_cmd_page_len() -
sizeof(struct virtio_net_ctrl_hdr)
- 2 * sizeof(struct virtio_net_ctrl_mac)) / ETH_ALEN` MAC addresses.
Considering the highly unlikely scenario for the guest setting
more than that number of MAC addresses for the filter table, this
should work fine for the majority of cases.
* If the CVQ command exceeds vhost_vdpa_net_cvq_cmd_page_len(),
instead of directly sending this CVQ command, QEMU should send
a VIRTIO_NET_CTRL_RX_PROMISC CVQ command to vdpa device. Addtionally,
a fake VIRTIO_NET_CTRL_MAC_TABLE_SET command including
(`MAC_TABLE_ENTRIES` + 1) non-multicast MAC addresses and
(`MAC_TABLE_ENTRIES` + 1) multicast MAC addresses should be provided
to the device model.
By doing so, the vdpa device turns promiscuous mode on, aligning
with the VirtIO standard. The device model marks
`n->mac_table.uni_overflow` and `n->mac_table.multi_overflow`,
which aligns with the state of the vdpa device.
Note that the bug cannot be triggered at the moment, since
VIRTIO_NET_F_CTRL_RX feature is not enabled for SVQ.
Fixes: 7a7f87e94c ("vdpa: Move command buffers map to start of net device")
Signed-off-by: Hawkins Jiawei <yin31149@gmail.com>
Message-Id: <267e15e4eed2d7aeb9887f193da99a13d22a2f1d.1688743107.git.yin31149@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We can access the CVQ header through `struct virtio_net_ctrl_hdr`,
instead of accessing it through a `uint8_t` pointer,
which improves the code's readability and maintainability.
Signed-off-by: Hawkins Jiawei <yin31149@gmail.com>
Message-Id: <cd522e06a4371e9d6b8a1c1a86f90a92401d56e8.1688743107.git.yin31149@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
QEMU uses vhost_svq_translate_addr() to translate addresses
between the QEMU's virtual address and the SVQ IOVA. In order
to validate this translation, QEMU checks whether the translated
range falls within the mapped range.
Yet the problem is that, the value of `needle_last`, which is calculated
by `needle.translated_addr + iovec[i].iov_len`, should represent the
exclusive boundary of the translated range, rather than the last
inclusive addresses of the range. Consequently, QEMU fails the check
when the translated range matches the size of the mapped range.
This patch solves this problem by fixing the `needle_last` value to
the last inclusive address of the translated range.
Note that this bug cannot be triggered at the moment, because QEMU
is unable to translate such a big range due to the truncation of
the CVQ command in vhost_vdpa_net_handle_ctrl_avail().
Fixes: 34e3c94eda ("vdpa: Add custom IOTLB translations to SVQ")
Signed-off-by: Hawkins Jiawei <yin31149@gmail.com>
Message-Id: <ee31c5420ffc8e6a29705ddd30badb814ddbae1d.1688743107.git.yin31149@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch introduces vhost_vdpa_net_load_rx_mode()
and vhost_vdpa_net_load_rx() to restore the packet
receive filtering state in relation to
VIRTIO_NET_F_CTRL_RX feature at device's startup.
Signed-off-by: Hawkins Jiawei <yin31149@gmail.com>
Message-Id: <804cedac93e19ba3b810d52b274ca5ec11469f09.1688743107.git.yin31149@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch refactors vhost_vdpa_net_load_mac() to
restore the MAC address filtering state at device's startup.
Signed-off-by: Hawkins Jiawei <yin31149@gmail.com>
Message-Id: <4b9550c14bc8c98c8f48e04dbf3d3ac41489d3fd.1688743107.git.yin31149@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
According to VirtIO standard, "The driver MUST follow
the VIRTIO_NET_CTRL_MAC_TABLE_SET command by a le32 number,
followed by that number of non-multicast MAC addresses,
followed by another le32 number, followed by that number
of multicast addresses."
Considering that these data is not stored in contiguous memory,
this patch refactors vhost_vdpa_net_load_cmd() to accept
scattered data, eliminating the need for an addtional data copy or
packing the data into s->cvq_cmd_out_buffer outside of
vhost_vdpa_net_load_cmd().
Signed-off-by: Hawkins Jiawei <yin31149@gmail.com>
Message-Id: <3482cc50eebd13db4140b8b5dec9d0cc25b20b1b.1688743107.git.yin31149@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The current implementers of ARI are all SR-IOV devices. The ARI next
function number field is undefined for VF according to PCI Express Base
Specification Revision 5.0 Version 1.0 section 9.3.7.7. The PF still
requires some defined value so end the linked list formed with the field
by specifying 0 as required for any ARI implementation according to
section 7.8.7.2.
For migration, the field will keep having 1 as its value on the old
QEMU machine versions.
Fixes: 2503461691 ("pcie: Add some SR/IOV API documentation in docs/pcie_sriov.txt")
Fixes: 44c2c09488 ("hw/nvme: Add support for SR-IOV")
Fixes: 3a977deebe ("Intrdocue igb device emulation")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Ani Sinha <anisinha@redhat.com>
Message-Id: <20230710153838.33917-3-akihiko.odaki@daynix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Currently the only implementers of ARI is SR-IOV devices, and they
behave similar. Share the ARI next function number.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Ani Sinha <anisinha@redhat.com>
Message-Id: <20230710153838.33917-2-akihiko.odaki@daynix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Lets document some more of the core VirtIODevice structure.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230710153522.3469097-7-alex.bennee@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230710153522.3469097-6-alex.bennee@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230710153522.3469097-5-alex.bennee@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Fixes: 544f0278af (virtio: introduce macro VIRTIO_CONFIG_IRQ_IDX)
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230710153522.3469097-4-alex.bennee@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
These are useful functions for when you want proper inheritance of
functionality across realize/unrealize calls.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230710153522.3469097-3-alex.bennee@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
I'm still not sure how I achieve by use case of the parent class
defining the following properties:
static Property vud_properties[] = {
DEFINE_PROP_CHR("chardev", VHostUserDevice, chardev),
DEFINE_PROP_UINT16("id", VHostUserDevice, id, 0),
DEFINE_PROP_UINT32("num_vqs", VHostUserDevice, num_vqs, 1),
DEFINE_PROP_END_OF_LIST(),
};
But for the specialisation of the class I want the id to default to
the actual device id, e.g.:
static Property vu_rng_properties[] = {
DEFINE_PROP_UINT16("id", VHostUserDevice, id, VIRTIO_ID_RNG),
DEFINE_PROP_UINT32("num_vqs", VHostUserDevice, num_vqs, 1),
DEFINE_PROP_END_OF_LIST(),
};
And so far the API for doing that isn't super clear.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20230710153522.3469097-2-alex.bennee@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
QEMU uses vhost_handle_guest_kick() to forward guest's available
buffers to the vdpa device in SVQ avail ring.
In vhost_handle_guest_kick(), a `g_autofree` `elem` is used to
iterate through the available VirtQueueElements. This `elem` is
then passed to `svq->ops->avail_handler`, specifically to the
vhost_vdpa_net_handle_ctrl_avail(). If this handler fails to
process the CVQ command, vhost_handle_guest_kick() regains
ownership of the `elem`, and either frees it or requeues it.
Yet the problem is that, vhost_vdpa_net_handle_ctrl_avail()
mistakenly frees the `elem`, even if it fails to forward the
CVQ command to vdpa device. This can result in a use-after-free
for the `elem` in vhost_handle_guest_kick().
This patch solves this problem by refactoring
vhost_vdpa_net_handle_ctrl_avail() to only freeing the `elem` if
it owns it.
Fixes: bd907ae4b0 ("vdpa: manual forward CVQ buffers")
Signed-off-by: Hawkins Jiawei <yin31149@gmail.com>
Message-Id: <e3f2d7db477734afe5c6a5ab3fa8b8317514ea34.1688746840.git.yin31149@gmail.com>
Reviewed-by: Eugenio Pérez <eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When trying to migrate a machine type pc-q35-6.0 or lower, with this
cmdline options,
-device driver=pcie-root-port,port=18,chassis=19,id=pcie-root-port18,bus=pcie.0,addr=0x12 \
-device driver=nec-usb-xhci,p2=4,p3=4,id=nex-usb-xhci0,bus=pcie-root-port18,addr=0x12.0x1
the following bug happens after all ram pages were sent:
qemu-kvm: get_pci_config_device: Bad config data: i=0x6e read: 0 device: 40 cmask: ff wmask: 0 w1cmask:19
qemu-kvm: Failed to load PCIDevice:config
qemu-kvm: Failed to load pcie-root-port:parent_obj.parent_obj.parent_obj
qemu-kvm: error while loading state for instance 0x0 of device '0000:00:12.0/pcie-root-port'
qemu-kvm: load of migration failed: Invalid argument
This happens on pc-q35-6.0 or lower because of:
{ "ICH9-LPC", ACPI_PM_PROP_ACPI_PCIHP_BRIDGE, "off" }
In this scenario, hotplug_handler_plug() calls pcie_cap_slot_plug_cb(),
which sets dev->config byte 0x6e with bit PCI_EXP_SLTSTA_PDS to signal PCI
hotplug for the guest. After a while the guest will deal with this hotplug
and qemu will clear the above bit.
Then, during migration, get_pci_config_device() will compare the
configs of both the freshly created device and the one that is being
received via migration, which will differ due to the PCI_EXP_SLTSTA_PDS bit
and cause the bug to reproduce.
To avoid this fake incompatibility, there are tree fields in PCIDevice that
can help:
- wmask: Used to implement R/W bytes, and
- w1cmask: Used to implement RW1C(Write 1 to Clear) bytes
- cmask: Used to enable config checks on load.
According to PCI Express® Base Specification Revision 5.0 Version 1.0,
table 7-27 (Slot Status Register) bit 6, the "Presence Detect State" is
listed as RO (read-only), so it only makes sense to make use of the cmask
field.
So, clear PCI_EXP_SLTSTA_PDS bit on cmask, so the fake incompatibility on
get_pci_config_device() does not abort the migration.
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=2215819
Signed-off-by: Leonardo Bras <leobras@redhat.com>
Message-Id: <20230706045546.593605-3-leobras@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
The current error messages in virtio_iommu_set_page_size_mask()
sound quite similar for different situations and miss the IOMMU
memory region that causes the issue.
Clarify them and rework the comment.
Also remove the trace when the new page_size_mask is not applied as
the current frozen granule is kept. This message is rather confusing
for the end user and anyway the current granule would have been used
by the driver.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Message-Id: <20230705165118.28194-3-eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Tested-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
When running on a 64kB page size host and protecting a VFIO device
with the virtio-iommu, qemu crashes with this kind of message:
qemu-kvm: virtio-iommu page mask 0xfffffffffffff000 is incompatible
with mask 0x20010000
qemu: hardware error: vfio: DMA mapping failed, unable to continue
This is due to the fact the IOMMU MR corresponding to the VFIO device
is enabled very late on domain attach, after the machine init.
The device reports a minimal 64kB page size but it is too late to be
applied. virtio_iommu_set_page_size_mask() fails and this causes
vfio_listener_region_add() to end up with hw_error();
To work around this issue, we transiently enable the IOMMU MR on
machine init to collect the page size requirements and then restore
the bypass state.
Fixes: 90519b9053 ("virtio-iommu: Add bypass mode support to assigned device")
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-Id: <20230705165118.28194-2-eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Tested-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
PCIe downstream ports only have a single device 0, so PCI Express devices can
only be plugged into slot 0 on a PCIe port. Add a warning to let users know
when the invalid configuration is used. We may enforce this more strongly later
once we get more clarity on whether we are introducing a bad regression for
users currently using the wrong configuration.
The change has been tested to not break or alter behaviors of ARI capable
devices by instantiating seven vfs on an emulated igb device (the maximum
number of vfs the igb device supports). The vfs are instantiated correctly
and are seen to have non-zero device/slot numbers in the conventional PCI BDF
representation.
CC: jusual@redhat.com
CC: imammedo@redhat.com
CC: mst@redhat.com
CC: akihiko.odaki@daynix.com
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=2128929
Signed-off-by: Ani Sinha <anisinha@redhat.com>
Reviewed-by: Julia Suvorova <jusual@redhat.com>
Message-Id: <20230705115925.5339-6-anisinha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Akihiko Odaki <akihiko.odaki@daynix.com>
The test attaches a SCSI controller to a non-zero slot and a pcie-to-pci bridge
on slot 0 on the same pcie-root-port. Since a downstream device can be attached
to a pcie-root-port only on slot 0, the above test configuration is not allowed.
Additionally using pcie.0 as id for pcie-to-pci bridge is incorrect as that id
is reserved only for the root bus.
In the test scenario, there is no need to attach a pcie-root-port to the
root complex. A SCSI controller can be attached to a pcie-to-pci bridge
which can then be directly attached to the root bus (pcie.0).
Fix the test and simplify it.
CC: mst@redhat.com
CC: imammedo@redhat.com
CC: Michael Labiuk <michael.labiuk@virtuozzo.com>
Acked-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Ani Sinha <anisinha@redhat.com>
Message-Id: <20230705115925.5339-5-anisinha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
PCIE ports only have one slot, slot 0. Hence, non-zero slots are not available
for PCIE devices on PCIE root ports. Fix test_acpi_q35_tcg_no_acpi_hotplug()
so that the test does not use them.
Signed-off-by: Ani Sinha <anisinha@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20230705115925.5339-3-anisinha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We are going to fix bio-tables-test in the next patch and hence need to
make sure the acpi tests continue to pass.
Signed-off-by: Ani Sinha <anisinha@redhat.com>
Acked-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20230705115925.5339-2-anisinha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
With TPM CRM device, vhost-vdpa reports an error when it tries
to register a listener for a non aligned memory region:
qemu-system-x86_64: vhost_vdpa_listener_region_add received unaligned region
qemu-system-x86_64: vhost_vdpa_listener_region_del received unaligned region
This error can be confusing for the user whereas we only need to skip
the region (as it's already done after the error_report())
Rather than introducing a special case for TPM CRB memory section
to not display the message in this case, simply replace the
error_report() by a trace function (with more information, like the
memory region name).
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Message-Id: <20230704071931.575888-2-lvivier@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
According to VirtIO standard, "The class, command and
command-specific-data are set by the driver,
and the device sets the ack byte.
There is little it can do except issue a diagnostic
if ack is not VIRTIO_NET_OK."
Therefore, QEMU should stop sending the queued SVQ commands and
cancel the device startup if the device's ack is not VIRTIO_NET_OK.
Yet the problem is that, vhost_vdpa_net_load_offloads() returns 1 based on
`*s->status != VIRTIO_NET_OK` when the device's ack is VIRTIO_NET_ERR.
As a result, net->nc->info->load() also returns 1, this makes
vhost_net_start_one() incorrectly assume the device state is
successfully loaded by vhost_vdpa_net_load() and return 0, instead of
goto `fail` label to cancel the device startup, as vhost_net_start_one()
only cancels the device startup when net->nc->info->load() returns a
negative value.
This patch fixes this problem by returning -EIO when the device's
ack is not VIRTIO_NET_OK.
Fixes: 0b58d3686a ("vdpa: Add vhost_vdpa_net_load_offloads()")
Signed-off-by: Hawkins Jiawei <yin31149@gmail.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Eugenio Pérez <eperezma@redhat.com>
Message-Id: <b0396b80e96322b86f1a0b10c098fc1edd947d72.1688438055.git.yin31149@gmail.com>
Tested-by: Lei Yang <leiyang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
According to VirtIO standard, "The class, command and
command-specific-data are set by the driver,
and the device sets the ack byte.
There is little it can do except issue a diagnostic
if ack is not VIRTIO_NET_OK."
Therefore, QEMU should stop sending the queued SVQ commands and
cancel the device startup if the device's ack is not VIRTIO_NET_OK.
Yet the problem is that, vhost_vdpa_net_load_mq() returns 1 based on
`*s->status != VIRTIO_NET_OK` when the device's ack is VIRTIO_NET_ERR.
As a result, net->nc->info->load() also returns 1, this makes
vhost_net_start_one() incorrectly assume the device state is
successfully loaded by vhost_vdpa_net_load() and return 0, instead of
goto `fail` label to cancel the device startup, as vhost_net_start_one()
only cancels the device startup when net->nc->info->load() returns a
negative value.
This patch fixes this problem by returning -EIO when the device's
ack is not VIRTIO_NET_OK.
Fixes: f64c7cda69 ("vdpa: Add vhost_vdpa_net_load_mq")
Signed-off-by: Hawkins Jiawei <yin31149@gmail.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Eugenio Pérez <eperezma@redhat.com>
Message-Id: <ec515ebb0b4f56368751b9e318e245a5d994fa72.1688438055.git.yin31149@gmail.com>
Tested-by: Lei Yang <leiyang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
According to VirtIO standard, "The class, command and
command-specific-data are set by the driver,
and the device sets the ack byte.
There is little it can do except issue a diagnostic
if ack is not VIRTIO_NET_OK."
Therefore, QEMU should stop sending the queued SVQ commands and
cancel the device startup if the device's ack is not VIRTIO_NET_OK.
Yet the problem is that, vhost_vdpa_net_load_mac() returns 1 based on
`*s->status != VIRTIO_NET_OK` when the device's ack is VIRTIO_NET_ERR.
As a result, net->nc->info->load() also returns 1, this makes
vhost_net_start_one() incorrectly assume the device state is
successfully loaded by vhost_vdpa_net_load() and return 0, instead of
goto `fail` label to cancel the device startup, as vhost_net_start_one()
only cancels the device startup when net->nc->info->load() returns a
negative value.
This patch fixes this problem by returning -EIO when the device's
ack is not VIRTIO_NET_OK.
Fixes: f73c0c43ac ("vdpa: extract vhost_vdpa_net_load_mac from vhost_vdpa_net_load")
Signed-off-by: Hawkins Jiawei <yin31149@gmail.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Eugenio Pérez <eperezma@redhat.com>
Message-Id: <a21731518644abbd0c495c5b7960527c5911f80d.1688438055.git.yin31149@gmail.com>
Tested-by: Lei Yang <leiyang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
pci_new() automatically retains a reference to a virtual function when
registering it so we need to release the reference when unregistering.
Fixes: 7c0fa8dff8 ("pcie: Add support for Single Root I/O Virtualization (SR/IOV)")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Message-Id: <20230411090408.48366-1-akihiko.odaki@daynix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
There is also pci_new() which creates non-multifunction PCI devices.
Accordingly the parameter is always set to true when a multi function PCI
device is to be created.
The reason for the parameter's existence seems to be that it is used in the
internal PCI code as well which is the only location where it gets set to
false. This one usage can be resolved by factoring out an internal helper
function.
Remove this redundant, error-prone parameter.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20230304114043.121024-6-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
There is also pci_create_simple() which creates non-multifunction PCI
devices. Accordingly the parameter is always set to true when a multi
function PCI device is to be created.
The reason for the parameter's existence seems to be that it is used in the
internal PCI code as well which is the only location where it gets set to
false. This one usage can be replaced by trivial code.
Remove this redundant, error-prone parameter.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20230304114043.121024-5-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
I440FX realization is currently mixed with PIIX3 creation. Furthermore, it is
common practice to only set properties between a device's qdev_new() and
qdev_realize(). Clean up to resolve both issues.
Since I440FX spawns a PCI bus let's also move the pci_bus initialization there.
Note that when running `qemu-system-x86_64 -M pc -S` before and after this
patch, `info mtree` in the QEMU console doesn't show any differences except that
the ordering is different.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230630073720.21297-18-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
i440fx_init() is a legacy init function. The previous patches worked towards
TYPE_I440FX_PCI_HOST_BRIDGE to be instantiated the QOM way. Do this now by
transforming the parameters passed to i440fx_init() into property assignments.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20230630073720.21297-17-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
I440FX needs a different PCI device model if the "igd-passthru" property is
enabled. The type name is currently passed as a parameter to i440fx_init(). This
parameter will be replaced by a property assignment once i440fx_init() gets
resolved.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20230630073720.21297-16-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Introduce the properties in anticipation of QOM'ification; Q35 has the same
properties.
Note that we want to avoid a "ram size" property in the QOM interface since it
seems redundant to both properties introduced in this change. Thus the removal
of the ram_size parameter. We assume the invariant of both properties to sum up
to "ram size" which is already asserted in pc_memory_init(). Under Xen the
invariant seems to hold as well, so we now also check it there.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20230630073720.21297-15-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Introduce the property in anticipation of QOM'ification; Q35 has the same
property.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20230630073720.21297-14-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The goal is to eliminate i440fx_init() which is a legacy init function. This
neccessitates the memory regions to be properties, like in Q35, which will be
assigned in board code.
Since i440fx needs different PCI devices in Xen mode, and since i440fx shall
be self-contained, the PCI device will be created during realization of the
host. Thus the pointers need to be moved to the host structure to be usable as
properties.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230630073720.21297-13-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
i440fx_realize() realizes the PCI device inside the host bridge
(PCII440FXState), but is implemented between i440fx_pcihost_realize() and
i440fx_init() which deal with the host bridge itself (I440FXState). Since we
want to append i440fx_init() to i440fx_pcihost_realize() later let's move
i440fx_realize() out of the way.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230630073720.21297-12-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
`PCIHostState` is often referred to as `phb`, own device state usually as `s`.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230630073720.21297-11-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230630073720.21297-10-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The parent-child relation is usually established near a child's qdev_new(). For
i440fx this allows for reusing the machine parameter, thus avoiding
qdev_get_machine() which relies on a global variable.
Suggested-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20230630073720.21297-9-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Eliminates an else branch.
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230630073720.21297-8-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20230630073720.21297-7-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The Q35 PCI host already has a PCI_HOST_BYPASS_IOMMU property. However, the
host initializes this property itself by accessing global machine state,
thereby assuming it to be a PC machine. Avoid this by having board code
set this property.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230630073720.21297-6-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Introduce a macro to avoid copy and pasting strings which can easily
cause typos.
Suggested-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20230630073720.21297-5-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The Q35 PCI host currently sets the PC machine's PCI bus attribute
through global state, thereby assuming the machine to be a PC machine.
The Q35 machine code already holds on to Q35's pci bus attribute, so can
easily set its own property while preserving encapsulation.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230630073720.21297-4-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Fixes the following clangd warning (-Winitializer-overrides):
q35.c:297:19: Initializer overrides prior initialization of this subobject
q35.c:292:19: previous initialization is here
Settle on little endian which is consistent with using pci_host_conf_le_ops.
Fixes: bafc90bdc5 ("q35: implement TSEG")
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230630073720.21297-3-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The variable is redundant to "phb" and is never used by its real type.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20230630073720.21297-2-shentey@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
A device reset is issued per device, not per VQ. The legacy device reset
message, VHOST_USER_RESET_OWNER, is already a per device message. Therefore,
this change adds the proper message, VHOST_USER_RESET_DEVICE, to per device
messages.
Signed-off-by: Tom Lonergan <tom.lonergan@nutanix.com>
Message-Id: <20230628163927.108171-3-tom.lonergan@nutanix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Some devices, like virtio-scsi, consist of one vhost_dev, while others, like
virtio-net, contain multiple vhost_devs. The QEMU vhost-user code has a
concept of one-time messages which is misleading. One-time messages are sent
once per operation on the device, not once for the lifetime of the device.
Therefore, as discussed in [1], vhost_user_one_time_request should be
renamed to vhost_user_per_device_request and the relevant comments updated
to match the real functionality.
[1] https://lore.kernel.org/qemu-devel/20230127083027-mutt-send-email-mst@kernel.org/
Signed-off-by: Tom Lonergan <tom.lonergan@nutanix.com>
Message-Id: <20230628163927.108171-2-tom.lonergan@nutanix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
