Reset requests should use SHUTDOWN_CAUSE_GUEST_RESET not
SHUTDOWN_CAUSE_GUEST_SHUTDOWN.
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20210624110057.2398779-1-kraxel@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Commit [1] moved _SUN variable from only hot-pluggable to
all devices. This made linux kernel enumerate extra slots
that weren't present before. If extra slot happens to be
be enumerated first and there is a device in th same slot
but on other bridge, linux kernel will add -N suffix to
slot name of the later, thus changing NIC name compared to
QEMU 5.2. This in some case confuses systemd, if it is
using SLOT NIC naming scheme and interface name becomes
not the same as it was under QEMU-5.2.
Reproducer QEMU CLI:
-M pc-i440fx-5.2 -nodefaults \
-device pci-bridge,chassis_nr=1,id=pci.1,bus=pci.0,addr=0x3 \
-device virtio-net-pci,id=nic1,bus=pci.1,addr=0x1 \
-device virtio-net-pci,id=nic2,bus=pci.1,addr=0x2 \
-device virtio-net-pci,id=nic3,bus=pci.1,addr=0x3
with RHEL8 guest produces following results:
v5.2:
kernel: virtio_net virtio0 ens1: renamed from eth0
kernel: virtio_net virtio2 ens3: renamed from eth2
kernel: virtio_net virtio1 enp1s2: renamed from eth1
(slot 2 is assigned to empty bus 0 slot and virtio1
is assigned to 2-2 slot, and renaming falls back,
for some reason, to path based naming scheme)
v6.0:
kernel: virtio_net virtio0 ens1: renamed from eth0
kernel: virtio_net virtio2 ens3: renamed from eth2
systemd-udevd[299]: Error changing net interface name 'eth1' to 'ens3': File exists
systemd-udevd[299]: could not rename interface '3' from 'eth1' to 'ens3': File exists
(with commit [1] kernel assigns virtio2 to 3-2 slot
since bridge advertises _SUN=0x3 and kernel assigns
slot 3 to bridge. Still it manages to rename virtio2
correctly to ens3, however systemd gets confused with virtio1
where slot allocation exactly the same (2-2) as in 5.2 case
and tries to rename it to ens3 which is rightfully taken by
virtio2)
I'm not sure what breaks in systemd interface renaming (it probably
should be investigated), but on QEMU side we can safely revert
_SUN to 5.2 behavior (i.e. avoid cold-plugged bridges and non
hot-pluggable device classes), without breaking acpi-index, which uses
slot numbers but it doesn't have to use _SUN, it could use an arbitrary
variable name that has the same slot value).
It will help existing VMs to keep networking with non trivial
configs in working order since systemd will do its interface
renaming magic as it used to do.
1)
Fixes: b7f23f62e4 (pci: acpi: add _DSM method to PCI devices)
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20210624204229.998824-3-imammedo@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Tested-by: John Sucaet <john.sucaet@ekinops.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20210624204229.998824-2-imammedo@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Tested-by: John Sucaet <john.sucaet@ekinops.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When the card is plugged back, reset the partially_hotplugged flag to false
Bug: https://bugzilla.redhat.com/show_bug.cgi?id=1787194
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Message-Id: <20210629152937.619193-1-lvivier@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
At some point, after unplugging virtio-pci the virtio device may be unrealised,
but the memory regions may be present in flatview. So, it's a possible situation
when memory region's callbacks are called for "unplugged" device.
Previous two patches made sure this case does not cause QEMU to crash.
This patch adds check for "notify" memory region. Now reads will return "-1" if a virtio
device is not present on a virtio bus.
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1938042
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1743098
Signed-off-by: Andrew Melnychenko <andrew@daynix.com>
Message-Id: <20210609095843.141378-4-andrew@daynix.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Now, if virtio device is not present on virtio-bus - pci config callbacks
will not lead to possible crush. The read will return "-1" which should be
interpreted by a driver that pci device may be unplugged.
Signed-off-by: Andrew Melnychenko <andrew@daynix.com>
Message-Id: <20210609095843.141378-3-andrew@daynix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
During unplug the virtio device is unplugged from virtio-bus on pci. In some cases,
requests to virtio-pci mm may acquire during/after unplug. Added check that virtio
device is on the bus, for "common" memory region.
Signed-off-by: Andrew Melnychenko <andrew@daynix.com>
Message-Id: <20210609095843.141378-2-andrew@daynix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
libFuzzer triggered the following assertion:
cat << EOF | qemu-system-i386 -M pc-q35-5.0 \
-nographic -monitor none -serial none \
-qtest stdio -d guest_errors -trace pci\*
outl 0xcf8 0xf2000060
outl 0xcfc 0x8400056e
EOF
pci_cfg_write mch 00:0 @0x60 <- 0x8400056e
Aborted (core dumped)
This is because guest wrote MCH_HOST_BRIDGE_PCIEXBAR_LENGTH_RVD
(reserved value) to the PCIE XBAR register.
There is no indication on the datasheet about what occurs when
this value is written. Simply ignore it on QEMU (and report an
guest error):
pci_cfg_write mch 00:0 @0x60 <- 0x8400056e
Q35: Reserved PCIEXBAR LENGTH
pci_cfg_read mch 00:0 @0x0 -> 0x8086
pci_cfg_read mch 00:0 @0x0 -> 0x29c08086
...
Cc: qemu-stable@nongnu.org
Reported-by: Alexander Bulekov <alxndr@bu.edu>
BugLink: https://bugs.launchpad.net/qemu/+bug/1878641
Fixes: df2d8b3ed4 ("q35: Introduce q35 pc based chipset emulator")
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210526142438.281477-1-f4bug@amsat.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Alexander Bulekov <alxndr@bu.edu>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The device model batching its ioeventfds in a single MR transaction is
an optimization. Clarify this in virtio-scsi, virtio-blk and generic
virtio code. Also clarify that the transaction must commit before
closing ioeventfds so that no one is tempted to merge the loops
in the start functions error path and in the stop functions.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <162125799728.1394228.339855768563326832.stgit@bahia.lan>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
virtio devices support separate iothreads waiting for
events from file descriptors. These are asynchronous
events that can't be recorded and replayed, therefore
this patch disables ioeventfd for all devices when
record or replay is enabled.
Signed-off-by: Pavel Dovgalyuk <Pavel.Dovgalyuk@ispras.ru>
Message-Id: <162125678869.1252810.4317416444097392406.stgit@pasha-ThinkPad-X280>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch *doesn't* update all of the docstring standards across the
QEMU package directory to make our docstring usage consistent. It
*doesn't* fix the formatting to make it look pretty or reasonable in
generated output. It *does* fix a few small instances where Sphinx would
emit a build warning because of malformed ReST -- If we built our Python
docs with Sphinx.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Willian Rampazzo <willianr@redhat.com>
Reviewed-by: Wainer dos Santos Moschetta <wainersm@redhat.com>
Message-id: 20210629214323.1329806-16-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
For reasons that at-present escape me, pipenv insists on creating a stub
pyproject.toml file. This file is a nuisance, because its mere presence
changes the behavior of various tools.
For instance, this stub file will cause "pip install --user -e ." to
fail in spectacular fashion with misleading errors. "pip install -e ."
works okay, but for some reason pip does not support editable installs
to the user directory when using PEP517.
References:
https://github.com/pypa/pip/pull/9990https://github.com/pypa/pip/issues/7953
As outlined in ea1213b7cc, it is still too early for us to consider
moving to a PEP-517 exclusive package. We must support older
distributions, so squash the annoyance for now. (Python 3.6 shipped Dec
2016, PEP517 support showed up in pip sometime in 2019 or so.)
Add 'pyproject.toml' to the 'make clean' target, and also delete it
after every pipenv invocation issued by the Makefile.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Willian Rampazzo <willianr@redhat.com>
Reviewed-by: Wainer dos Santos Moschetta <wainersm@redhat.com>
Message-id: 20210629214323.1329806-15-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
Update for visual parity with all the remaining targets.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Willian Rampazzo <willianr@redhat.com>
Reviewed-by: Wainer dos Santos Moschetta <wainersm@redhat.com>
Message-id: 20210629214323.1329806-14-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
Update for visual parity with the other targets.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Willian Rampazzo <willianr@redhat.com>
Reviewed-by: Wainer dos Santos Moschetta <wainersm@redhat.com>
Message-id: 20210629214323.1329806-13-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
This is a *third* way to run the Python tests. Unlike the first two
(check-pipenv, check-tox), this version does not require any specific
interpreter version -- making it a lot easier to tell people to run it
as a quick smoketest prior to submission to GitLab CI.
Summary:
Checked via GitLab CI:
- check-pipenv: tests our oldest python & dependencies
- check-tox: tests newest dependencies on all non-EOL python versions
Executed only incidentally:
- check-dev: tests newest dependencies on whichever python version
('make check' does not set up any environment at all, it just runs the
tests in your current environment. All four invocations perform the
exact same tests, just in different execution environments.)
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Willian Rampazzo <willianr@redhat.com>
Reviewed-by: Wainer dos Santos Moschetta <wainersm@redhat.com>
Tested-by: Wainer dos Santos Moschetta <wainersm@redhat.com>
Message-id: 20210629214323.1329806-12-jsnow@redhat.com
[Maintainer edit: added .dev-venv/ to .gitignore. --js]
Acked-by: Wainer dos Santos Moschetta <wainersm@redhat.com>
Acked-by: Willian Rampazzo <willianr@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
flake8 is a little eager to check everything it can. Limit it to
checking inside the qemu namespace directory only. Update setup.cfg now
that the exclude patterns are no longer necessary.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Willian Rampazzo <willianr@redhat.com>
Reviewed-by: Wainer dos Santos Moschetta <wainersm@redhat.com>
Tested-by: Wainer dos Santos Moschetta <wainersm@redhat.com>
Message-id: 20210629214323.1329806-11-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
I missed the 'check-tox' target. Add that, but split the large .PHONY
specifier at the top into its component pieces and move them near the
targets they describe so that they're much harder to forget to update.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Wainer dos Santos Moschetta <wainersm@redhat.com>
Reviewed-by: Willian Rampazzo <willianr@redhat.com>
Message-id: 20210629214323.1329806-10-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
Move it up near the check-pipenv help text, and update it to suggest parity.
(At the time I first added it, I wasn't sure if I would be keeping it,
but I've come to appreciate it as it has actually helped uncover bugs I
would not have noticed without it. It should stay.)
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Willian Rampazzo <willianr@redhat.com>
Reviewed-by: Wainer dos Santos Moschetta <wainersm@redhat.com>
Message-id: 20210629214323.1329806-9-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
Well, Cleber was right, this is a better name.
In preparation for adding a different kind of virtual environment check
(One that simply uses whichever version of Python you happen to have),
rename this test 'check-pipenv' so that it matches the CI job
'check-python-pipenv'.
Remove the "If you don't know which test to run" hint, because it's not
actually likely you have Python 3.6 installed to be able to run the
test. It's still the test I'd most prefer you to run, but it's not the
test you are most likely to be able to run.
Rename the 'venv' target to 'pipenv' as well, and move the more
pertinent help text under the 'check-pipenv' target.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Willian Rampazzo <willianr@redhat.com>
Reviewed-by: Wainer dos Santos Moschetta <wainersm@redhat.com>
Message-id: 20210629214323.1329806-8-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
It's not encouraged, but it's legitimate to want to know how to do.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Willian Rampazzo <willianr@redhat.com>
Reviewed-by: Wainer dos Santos Moschetta <wainersm@redhat.com>
Message-id: 20210629214323.1329806-7-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
Clarifying a few points; removing the reference to 'setuptools' because
it isn't referenced anywhere else in this document and doesn't really
provide any useful information to a Python newcomer.
Adjusting the language elsewhere to be less ambiguous and have fewer
run-on sentences.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Willian Rampazzo <willianr@redhat.com>
Reviewed-by: Wainer dos Santos Moschetta <wainersm@redhat.com>
Message-id: 20210629214323.1329806-6-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
tox is already testing the most recent versions. Let's use pipenv to
test the oldest versions we claim to support. This matches the stylistic
choice to have pipenv always test our oldest supported Python version, 3.6.
The effect of this is that the python-check-pipenv CI job on gitlab will
now test against much older versions of these linters, which will help
highlight incompatible changes that might otherwise go unnoticed.
Update instructions for adding and bumping versions in setup.cfg. The
reason for deleting the line that gets added to Pipfile is largely just
to avoid having the version minimums specified in multiple places in
config checked into the tree.
(This patch was written by deleting Pipfile and Pipfile.lock, then
explicitly installing each dependency manually at a specific
version. Then, I restored the prior Pipfile and re-ran `pipenv lock
--dev --keep-outdated` to re-add the qemu dependency back to the pipenv
environment while keeping the "old" packages. It's annoying, yes, but I
think the improvement to test coverage is worthwhile.)
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Willian Rampazzo <willianr@redhat.com>
Reviewed-by: Wainer dos Santos Moschetta <wainersm@redhat.com>
Message-id: 20210629214323.1329806-5-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
These suppressions only apply to a small handful of places. Instead of
disabling them globally, disable them just in the cases where we
need. The design of the machine class grew quite organically with tons
of constructor and class instance variables -- there's little chance of
meaningfully refactoring it in the near term, so just suppress the
warnings for that class.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Willian Rampazzo <willianr@redhat.com>
Reviewed-by: Wainer dos Santos Moschetta <wainersm@redhat.com>
Message-id: 20210629214323.1329806-4-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
https://www.python.org/dev/peps/pep-0561/#specification
Create 'py.typed' files in each subpackage that indicate to mypy that
this is a typed module, so that users of any of these packages can use
mypy to check their code as well.
Note: Theoretically it's possible to ditch MANIFEST.in in favor of using
package_data in setup.cfg, but I genuinely could not figure out how to
get it to include things from the *source root* into the *package root*;
only how to include things from each subpackage. I tried!
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Willian Rampazzo <willianr@redhat.com>
Reviewed-by: Wainer dos Santos Moschetta <wainersm@redhat.com>
Message-id: 20210629214323.1329806-3-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
Pylint updated to 2.9.0 upstream, adding new warnings for things that
re-use the 'err' variable. Luckily, this only breaks the
python-check-tox job, which is allowed to fail as a warning.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Wainer dos Santos Moschetta <wainersm@redhat.com>
Reviewed-by: Willian Rampazzo <willianr@redhat.com>
Message-id: 20210629214323.1329806-2-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
* namespace eui64 support (Heinrich)
* aiocb refactoring (Klaus)
* controller parameter for auto zone transitioning (Niklas)
* misc fixes and additions (Gollu, Klaus, Keith)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEUigzqnXi3OaiR2bATeGvMW1PDekFAmDbap8ACgkQTeGvMW1P
Denz9wf9GtU4z7G0pQpFlv1smWPvQfv9qlkGiRvGcIQjEgPjcKjEsJC1CqtG6nZ5
BGYzey706iM7NAs6wPkyUyHgWXl+N/Ku5nNBvNJuzTN5J9aHgnqehe8civvS6ONU
0WtAQEEZCLu0Qbvw6KawCShXrJ6Jpmu+bYGggYEy5+baumLF0Qj50l2wRiDbImNu
rE3iZuhEenwnNNSTTkyt2RT8lSzizAtth4bAqzl3Zw1Q3NO+qDCL0wPOWD7YuD8p
LTZ8/ojB1+YUI3JrMM4MlzbJyGstdk2Y5zq6QpAcf86agaaFEmS0iqjOic52ImpL
VzmZZZ0W7kmhJVc5H/Q5y/KAFIHnFA==
=efjI
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/nvme/tags/nvme-next-pull-request' into staging
hw/nvme patches
* namespace eui64 support (Heinrich)
* aiocb refactoring (Klaus)
* controller parameter for auto zone transitioning (Niklas)
* misc fixes and additions (Gollu, Klaus, Keith)
# gpg: Signature made Tue 29 Jun 2021 19:46:55 BST
# gpg: using RSA key 522833AA75E2DCE6A24766C04DE1AF316D4F0DE9
# gpg: Good signature from "Klaus Jensen <its@irrelevant.dk>" [unknown]
# gpg: aka "Klaus Jensen <k.jensen@samsung.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: DDCA 4D9C 9EF9 31CC 3468 4272 63D5 6FC5 E55D A838
# Subkey fingerprint: 5228 33AA 75E2 DCE6 A247 66C0 4DE1 AF31 6D4F 0DE9
* remotes/nvme/tags/nvme-next-pull-request: (23 commits)
hw/nvme: add 'zoned.zasl' to documentation
hw/nvme: fix pin-based interrupt behavior (again)
hw/nvme: fix missing check for PMR capability
hw/nvme: documentation fix
hw/nvme: fix endianess conversion and add controller list
Partially revert "hw/block/nvme: drain namespaces on sq deletion"
hw/nvme: reimplement format nvm to allow cancellation
hw/nvme: reimplement zone reset to allow cancellation
hw/nvme: reimplement the copy command to allow aio cancellation
hw/nvme: add dw0/1 to the req completion trace event
hw/nvme: use prinfo directly in nvme_check_prinfo and nvme_dif_check
hw/nvme: remove assert from nvme_get_zone_by_slba
hw/nvme: save reftag when generating pi
hw/nvme: reimplement dsm to allow cancellation
hw/nvme: add nvme_block_status_all helper
hw/nvme: reimplement flush to allow cancellation
hw/nvme: default for namespace EUI-64
hw/nvme: namespace parameter for EUI-64
hw/nvme: fix csi field for cns 0x00 and 0x11
hw/nvme: add param to control auto zone transitioning to zone state closed
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Commit dabefdd6 removed code that was supposed to try reconnecting
during .realize(), but actually just crashed and had several design
problems.
This adds the feature back without the crash in simple cases while also
fixing some design problems: Reconnection is now only tried if there was
a problem with the connection and not an error related to the content
(which would fail again the same way in the next attempt). Reconnection
is limited to three attempts (four with the initial attempt) so that we
won't end up in an infinite loop if a problem is permanent. If the
backend restarts three times in the very short time window of device
initialisation, we have bigger problems and erroring out is the right
course of action.
In the case that a connection error occurs and we reconnect, the error
message is printed using error_report_err(), but otherwise ignored.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20210609154658.350308-8-kwolf@redhat.com>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This function is the part that we will want to retry if the connection
is lost during initialisation, so factor it out to keep the following
patch simpler.
The error path for vhost_dev_get_config() forgot disconnecting the
chardev, add this while touching the code.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20210609154658.350308-7-kwolf@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Instead of just returning 0/-1 and letting the caller make up a
meaningless error message, add an Error parameter to allow reporting the
real error and switch to 0/-errno so that different kind of errors can
be distinguished in the caller.
config_len in vhost_user_get_config() is defined by the device, so if
it's larger than VHOST_USER_MAX_CONFIG_SIZE, this is a programming
error. Turn the corresponding check into an assertion.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20210609154658.350308-6-kwolf@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Instead of letting the caller make up a meaningless error message, add
an Error parameter to allow reporting the real error.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20210609154658.350308-5-kwolf@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Instead of just returning 0/-1 and letting the caller make up a
meaningless error message, switch to 0/-errno so that different kinds of
errors can be distinguished in the caller.
This involves changing a few more callbacks in VhostOps to return
0/-errno: .vhost_set_owner(), .vhost_get_features() and
.vhost_virtqueue_set_busyloop_timeout(). The implementations of these
functions are trivial as they generally just send a message to the
backend.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20210609154658.350308-4-kwolf@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Instead of just returning 0/-1 and letting the caller make up a
meaningless error message, add an Error parameter to allow reporting the
real error and switch to 0/-errno so that different kind of errors can
be distinguished in the caller.
Specifically, in vhost-user, EPROTO is used for all errors that relate
to the connection itself, whereas other error codes are used for errors
relating to the content of the connection. This will allow us later to
automatically reconnect when the connection goes away, without ending up
in an endless loop if it's a permanent error in the configuration.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20210609154658.350308-3-kwolf@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This allows callers to return better error messages instead of making
one up while the real error ends up on stderr. Most callers can
immediately make use of this because they already have an Error
parameter themselves. The others just keep printing the error with
error_report_err().
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20210609154658.350308-2-kwolf@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Currently the SSH block driver supports MD5 and SHA1 for host key
fingerprints. This is a cryptographically sensitive operation and
so these hash algorithms are inadequate by modern standards. This
adds support for SHA256 which has been supported in libssh since
the 0.8.1 release.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20210622115156.138458-1-berrange@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Richard W.M. Jones <rjones@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Code consuming the "crypto/tlscreds*.h" APIs doesn't need
to access its internals. Move the structure definitions to
the "tlscredspriv.h" private header (only accessible by
implementations). The public headers (in include/) still
forward-declare the structures typedef.
Note, tlscreds.c and 3 of the 5 modified source files already
include "tlscredspriv.h", so only add it to tls-cipher-suites.c
and tlssession.c.
Removing the internals from the public header solves a bug
introduced by commit 7de2e85653 ("yank: Unregister function
when using TLS migration") which made migration/qemu-file-channel.c
include "io/channel-tls.h", itself sometime depends on GNUTLS,
leading to a build failure on OSX:
[2/35] Compiling C object libmigration.fa.p/migration_qemu-file-channel.c.o
FAILED: libmigration.fa.p/migration_qemu-file-channel.c.o
cc -Ilibmigration.fa.p -I. -I.. -Iqapi [ ... ] -o libmigration.fa.p/migration_qemu-file-channel.c.o -c ../migration/qemu-file-channel.c
In file included from ../migration/qemu-file-channel.c:29:
In file included from include/io/channel-tls.h:26:
In file included from include/crypto/tlssession.h:24:
include/crypto/tlscreds.h:28:10: fatal error: 'gnutls/gnutls.h' file not found
#include <gnutls/gnutls.h>
^~~~~~~~~~~~~~~~~
1 error generated.
Reported-by: Stefan Weil <sw@weilnetz.de>
Suggested-by: Daniel P. Berrangé <berrange@redhat.com>
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/407
Fixes: 7de2e85653 ("yank: Unregister function when using TLS migration")
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Avoid accessing QCryptoTLSCreds internals by using
the qcrypto_tls_creds_check_endpoint() helper.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Avoid accessing QCryptoTLSCreds internals by using
the qcrypto_tls_creds_check_endpoint() helper.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Avoid accessing QCryptoTLSCreds internals by using
the qcrypto_tls_creds_check_endpoint() helper.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Avoid accessing QCryptoTLSCreds internals by using
the qcrypto_tls_creds_check_endpoint() helper.
Tested-by: Akihiko Odaki <akihiko.odaki@gmail.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Avoid accessing QCryptoTLSCreds internals by using
the qcrypto_tls_creds_check_endpoint() helper.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Introduce the qcrypto_tls_creds_check_endpoint() helper
to access QCryptoTLSCreds internal 'endpoint' field.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
TCG_TARGET_HAS_MEMORY_BSWAP is already unset for this backend,
which means that MO_BSWAP be handled by the middle-end and
will never be seen by the backend. Thus the indexes used with
qemu_{ld,st}_helpers will always be zero.
Tidy the comments and asserts in tcg_out_qemu_{ld,st}_direct.
It is not that we do not handle bswap "yet", but never will.
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The memory bswap support in the aarch64 backend merely dates from
a time when it was required. There is nothing special about the
backend support that could not have been provided by the middle-end
even prior to the introduction of the bswap flags.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
