The Legacy virtio-pci interface always uses BAR 0. VIRTIO 1.0 may need
to use a different BAR index, so make it configurable.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20191023100425.12168-15-stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The VIRTIO 1.0 code will need to perform additional steps but it will
reuse the common virtqueue setup/cleanup code. Make these functions
public.
Make sure to invoke callbacks via QVirtioBus instead of directly calling
the virtio-pci Legacy versions of these functions.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Sergio Lopez <slp@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20191023100425.12168-14-stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The MSI-X vectors are programmed differently in the VIRTIO 1.0 and
Legacy interfaces. Introduce callbacks so different implementations can
be used depending on the interface version.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Sergio Lopez <slp@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20191023100425.12168-13-stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Instead of just passing the vring page frame number, pass the full
QVirtQueue. This will allow the VIRTIO 1.0 transport to program the
fine-grained vring address registers in the future.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Sergio Lopez <slp@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20191023100425.12168-12-stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
VIRTIO 1.0 PCI devices have multiple PCI_CAP_ID_VNDR capabilities so we
need a way to iterate over them. Extend qpci_find_capability() to take
the last address.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
--
v3:
* Document qpci_find_capability()
Message-Id: <20191023100425.12168-11-stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
VIRTIO 1.0 uses little-endian for the vring. Legacy VIRTIO uses guest
endianness. Adjust the code to handle both.
Note that qvirtio_readq() is not defined because it has no users. All
the other accessors are really needed.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20191023100425.12168-10-stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Device initialization has an extra step in VIRTIO 1.0. The FEATURES_OK
status bit is set to indicate that feature negotiation has completed.
The driver then reads the status register again to check that the device
agrees with the final features.
Implement this step as part of qvirtio_set_features() instead of
introducing a separate function. This way all existing code works
without modifications.
The check in qvirtio_set_driver_ok() needs to be updated because
FEATURES_OK will be set for VIRTIO 1.0 devices.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20191023100425.12168-9-stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Thomas Huth" <thuth@redhat.com>
According to VIRTIO 1.1 "3.1.1 Driver Requirements: Device
Initialization", configuration space and virtqueues cannot be accessed
before features have been negotiated. Enforce this requirement.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20191023100425.12168-8-stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
VIRTIO Device Initialization requires feature negotiation. The libqos
virtio-9p driver lacks feature negotiation and is therefore
non-compliant.
libqos tests acknowledge all feature bits advertised by the device,
except VIRTIO_F_BAD_FEATURE (which devices use to detect broken
drivers!) and VIRTIO_RING_F_EVENT_IDX (which is not implemented in
libqos and accepting it would break notifications).
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20191023100425.12168-7-stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Thomas Huth" <thuth@redhat.com>
VIRTIO Device Initialization requires that feature negotiation has
completed before virtqueues are set up. This makes sense because the
driver must know whether it is operating in Legacy or VIRTIO 1.0 mode
before it can access vring fields with the correct endianness.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20191023100425.12168-6-stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
VIRTIO Device Initialization requires feature negotiation. Currently
virtio-scsi-test.c is non-compliant.
libqos tests acknowledge all feature bits advertised by the device,
except VIRTIO_F_BAD_FEATURE (which devices use to detect broken
drivers!) and VIRTIO_RING_F_EVENT_IDX (which is not implemented in
libqos and accepting it would break notifications).
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20191023100425.12168-5-stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Thomas Huth" <thuth@redhat.com>
In VIRTIO 1.0 feature bits changed from 32-bit to 64-bit. (In fact, the
transports allow even more feature bits but nothing uses more than 64
bits today.)
Add 64-bit feature bit support to virtio-mmio and virtio-pci. This will
be necessary for VIRTIO 1.0 support.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20191023100425.12168-4-stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
There was no real virtio-mmio ABI change between Legacy and VIRTIO 1.0
except that the Version field was incremented from 1 to 2.
However, QEMU does not allow Legacy drivers to perform VIRTIO 1.0
operations like accessing 64-bit feature bits. Since we will introduce
64-bit feature bit support we need a way to differentiate between
virtio-mmio Version 1 and 2 to avoid upsetting QEMU when we operate in
Legacy mode.
Stash away the Version field so later patches can change behavior
depending on the version.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20191023100425.12168-3-stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The VIRTIO Configuration Space cannot be accessed before device feature
bits have been read because a driver doesn't know the endianness until
it has checked VIRTIO_F_VERSION_1.
Fix this problem in preparation for VIRTIO 1.0 support.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20191023100425.12168-2-stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Reviewed-by: Jens Freimann <jfreimann@redhat.com>
Message-Id: <20191025083527.30803-9-eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Reviewed-by: Jens Freimann <jfreimann@redhat.com>
Message-Id: <20191025083527.30803-8-eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch implements event suppression through device/driver
area. Please refer virtio specification for more information.
Signed-off-by: Wei Xu <wexu@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Message-Id: <20191025083527.30803-7-eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch implements basic support for the packed virtqueue. Compare
the split virtqueue which has three rings, packed virtqueue only have
one which is supposed to have better cache utilization and more
hardware friendly.
Please refer virtio specification for more information.
Signed-off-by: Wei Xu <wexu@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Message-Id: <20191025083527.30803-6-eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The function virtio_del_queue was not called at unrealize() callback.
This was detected due to add an allocated element on the vq introduce
in future commits (used_elems) and running address sanitizer memory
leak detector.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Message-Id: <20191025083527.30803-5-eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The function virtio_del_queue was not called at unrealize() callback.
This was detected due to add an allocated element on the vq introduce
in future commits (used_elems) and running address sanitizer memory
leak detector.
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Message-Id: <20191025083527.30803-4-eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
There is slight size difference between split/packed rings.
This is the refactor of split ring as well as a helper to expanding
device and driver area size calculation for packed ring.
Signed-off-by: Wei Xu <wexu@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Reviewed-by: Jens Freimann <jfreimann@redhat.com>
Message-Id: <20191025083527.30803-3-eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Define packed ring structure according to Qemu nomenclature,
field data(wrap counter, etc) are also included.
Signed-off-by: Wei Xu <wexu@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Eugenio Pérez <eperezma@redhat.com>
Reviewed-by: Jens Freimann <jfreimann@redhat.com>
Message-Id: <20191025083527.30803-2-eperezma@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Last pull request before soft freeze.
* Lots of fixes and cleanups for spapr interrupt controllers
* More SLOF updates to fix problems with full FDT rendering at CAS
time (alas, more yet are to come)
* A few other assorted changes
This isn't quite as well tested as I usually try to do before a pull
request. But I've been sick and running into some other difficulties,
and wanted to get this sent out before heading towards KVM forum.
-----BEGIN PGP SIGNATURE-----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=FRHF
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-4.2-20191024' into staging
ppc patch queue 2019-10-24
Last pull request before soft freeze.
* Lots of fixes and cleanups for spapr interrupt controllers
* More SLOF updates to fix problems with full FDT rendering at CAS
time (alas, more yet are to come)
* A few other assorted changes
This isn't quite as well tested as I usually try to do before a pull
request. But I've been sick and running into some other difficulties,
and wanted to get this sent out before heading towards KVM forum.
# gpg: Signature made Thu 24 Oct 2019 09:14:31 BST
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-4.2-20191024: (28 commits)
spapr/xive: Set the OS CAM line at reset
ppc/pnv: Fix naming of routines realizing the CPUs
ppc: Reset the interrupt presenter from the CPU reset handler
ppc/pnv: Add a PnvChip pointer to PnvCore
ppc/pnv: Introduce a PnvCore reset handler
spapr_cpu_core: Implement DeviceClass::reset
spapr: move CPU reset after presenter creation
spapr: Don't request to unplug the same core twice
pseries: Update SLOF firmware image
spapr: Move SpaprIrq::nr_xirqs to SpaprMachineClass
spapr: Remove SpaprIrq::nr_msis
spapr, xics, xive: Move SpaprIrq::post_load hook to backends
spapr, xics, xive: Move SpaprIrq::reset hook logic into activate/deactivate
spapr: Remove SpaprIrq::init_kvm hook
spapr, xics, xive: Match signatures for XICS and XIVE KVM connect routines
spapr, xics, xive: Move dt_populate from SpaprIrq to SpaprInterruptController
spapr, xics, xive: Move print_info from SpaprIrq to SpaprInterruptController
spapr, xics, xive: Move set_irq from SpaprIrq to SpaprInterruptController
spapr: Formalize notion of active interrupt controller
spapr, xics, xive: Move irq claim and free from SpaprIrq to SpaprInterruptController
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
machine_hppa_init() violates memory_region_allocate_system_memory() contract
by calling it multiple times which could break with -mem-path. Replace
the second usage (for 'rom') with memory_region_init_ram() instead.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20191008113318.7012-4-imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
rs6000mc_realize() violates memory_region_allocate_system_memory() contract
by calling it multiple times which could break -mem-path. Replace it with
plain memory_region_init_ram() instead.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20191008113318.7012-3-imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
memory_region_allocate_system_memory() was designed to be called for
allocating inital RAM. Using it mutiple times within one board is not
supported and could fail if -mem-path with non hugepage path is used.
Keep using memory_region_allocate_system_memory() only for initial
RAM and use memory_region_init_ram() for the rest fixed size regions.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20191008113318.7012-2-imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Denverton is the Atom Processor of Intel Harrisonville platform.
For more information:
https://ark.intel.com/content/www/us/en/ark/products/\
codename/63508/denverton.html
Signed-off-by: Tao Xu <tao3.xu@intel.com>
Message-Id: <20190718073405.28301-1-tao3.xu@intel.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
When a Virtual Processor is scheduled to run on a HW thread, the
hypervisor pushes its identifier in the OS CAM line. When running with
kernel_irqchip=off, QEMU needs to emulate the same behavior.
Set the OS CAM line when the interrupt presenter of the sPAPR core is
reset. This will also cover the case of hot-plugged CPUs.
This change also has the benefit to remove the use of CPU_FOREACH()
which can be unsafe.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-Id: <20191022163812.330-8-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The 'vcpu' suffix is inherited from the sPAPR machine. Use better
names for PowerNV.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-Id: <20191022163812.330-7-clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
On the sPAPR machine and PowerNV machine, the interrupt presenters are
created by a machine handler at the core level and are reset
independently. This is not consistent and it raises issues when it
comes to handle hot-plugged CPUs. In that case, the presenters are not
reset. This is less of an issue in XICS, although a zero MFFR could
be a concern, but in XIVE, the OS CAM line is not set and this breaks
the presenting algorithm. The current code has workarounds which need
a global cleanup.
Extend the sPAPR IRQ backend and the PowerNV Chip class with a new
cpu_intc_reset() handler called by the CPU reset handler and remove
the XiveTCTX reset handler which is now redundant.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191022163812.330-6-clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
We will use it to reset the interrupt presenter from the CPU reset
handler.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-Id: <20191022163812.330-5-clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
in which individual CPUs are reset. It will ease the introduction of
future change reseting the interrupt presenter from the CPU reset
handler.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-Id: <20191022163812.330-4-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Since vCPUs aren't plugged into a bus, we manually register a reset
handler for each vCPU. We also call this handler at realize time
to ensure hot plugged vCPUs are reset before being exposed to the
guest. This results in vCPUs being reset twice at machine reset.
It doesn't break anything but it is slightly suboptimal and above
all confusing.
The hotplug path in device_set_realized() already knows how to reset
a hotplugged device if the device reset handler is present. Implement
one for sPAPR CPU cores that resets all vCPUs under a core.
While here rename spapr_cpu_reset() to spapr_reset_vcpu() for
consistency with spapr_realize_vcpu() and spapr_unrealize_vcpu().
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[clg: add documentation on the reset helper usage ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191022163812.330-3-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This change prepares ground for future changes which will reset the
interrupt presenter in the reset handler of the sPAPR and PowerNV
cores.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20191022163812.330-2-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
We must not call spapr_drc_detach() on a detached DRC otherwise bad things
can happen, ie. QEMU hangs or crashes. This is easily demonstrated with
a CPU hotplug/unplug loop using QMP.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157185826035.3073024.1664101000438499392.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This aims v4.2 and fixes:
1. full FDT rendering;
2. gcc9 -Waddress-of-packed-member.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
For the benefit of peripheral device allocation, the number of available
irqs really wants to be the same on a given machine type version,
regardless of what irq backends we are using. That's the case now, but
only because we make sure the different SpaprIrq instances have the same
value except for the special legacy one.
Since this really only depends on machine type version, move the value to
SpaprMachineClass instead of SpaprIrq. This also puts the code to set it
to the lower value on old machine types right next to setting
legacy_irq_allocation, which needs to go hand in hand.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
The nr_msis value we use here has to line up with whether we're using
legacy or modern irq allocation. Therefore it's safer to derive it based
on legacy_irq_allocation rather than having SpaprIrq contain a canned
value.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
The remaining logic in the post_load hook really belongs to the interrupt
controller backends, and just needs to be called on the active controller
(after the active controller is set to the right thing based on the
incoming migration in the generic spapr_irq_post_load() logic).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
It turns out that all the logic in the SpaprIrq::reset hooks (and some in
the SpaprIrq::post_load hooks) isn't really related to resetting the irq
backend (that's handled by the backends' own reset routines). Rather its
about getting the backend ready to be the active interrupt controller or
stopping being the active interrupt controller - reset (and post_load) is
just the only time that changes at present.
To make this flow clearer, move the logic into the explicit backend
activate and deactivate hooks.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
This hook is a bit odd. The only caller is spapr_irq_init_kvm(), but
it explicitly takes an SpaprIrq *, so it's never really called through the
current SpaprIrq. Essentially this is just a way of passing through a
function pointer so that spapr_irq_init_kvm() can handle some
configuration and error handling logic without duplicating it between the
xics and xive reset paths.
So, make it just take that function pointer. Because of earlier reworks
to the KVM connect/disconnect code in the xics and xive backends we can
also eliminate some wrapper functions and streamline error handling a bit.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Both XICS and XIVE have routines to connect and disconnect KVM with
similar but not identical signatures. This adjusts them to match
exactly, which will be useful for further cleanups later.
While we're there, we add an explicit return value to the connect path
to streamline error reporting in the callers. We remove error
reporting the disconnect path. In the XICS case this wasn't used at
all. In the XIVE case the only error case was if the KVM device was
set up, but KVM didn't have the capability to do so which is pretty
obviously impossible.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
This method depends only on the active irq controller. Now that we've
formalized the notion of active controller we can dispatch directly
through that, rather than dispatching via SpaprIrq with the dual
version having to do a second conditional dispatch.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
This method depends only on the active irq controller. Now that we've
formalized the notion of active controller we can dispatch directly
through that, rather than dispatching via SpaprIrq with the dual
version having to do a second conditional dispatch.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
This method depends only on the active irq controller. Now that we've
formalized the notion of active controller we can dispatch directly through
that, rather than dispatching via SpaprIrq with the dual version having
to do a second conditional dispatch.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
spapr now has the mechanism of constructing both XICS and XIVE instances of
the SpaprInterruptController interface. However, only one of the interrupt
controllers will actually be active at any given time, depending on feature
negotiation with the guest. This is handled in the current code via
spapr_irq_current() which checks the OV5 vector from feature negotiation to
determine the current backend.
Determining the active controller at the point we need it like this
can be pretty confusing, because it makes it very non obvious at what
points the active controller can change. This can make it difficult
to reason about the code and where a change of active controller could
appear in sequence with other events.
Make this mechanism more explicit by adding an 'active_intc' pointer
and an explicit spapr_irq_update_active_intc() function to update it
from the CAS state. We also add hooks on the intc backend which will
get called when it is activated or deactivated.
For now we just introduce the switch and hooks, later patches will
actually start using them.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
These methods, like cpu_intc_create, really belong to the interrupt
controller, but need to be called on all possible intcs.
Like cpu_intc_create, therefore, make them methods on the intc and
always call it for all existing intcs.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
This method essentially represents code which belongs to the interrupt
controller, but needs to be called on all possible intcs, rather than
just the currently active one. The "dual" version therefore calls
into the xics and xive versions confusingly.
Handle this more directly, by making it instead a method on the intc
backend, and always calling it on every backend that exists.
While we're there, streamline the error reporting a bit.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Stefan Hajnoczi
Jason Wang
Eugenio Pérez
Wei Xu
Peter Maydell
Igor Mammedov
Tao Xu
Cédric Le Goater
Greg Kurz
Alexey Kardashevskiy
David Gibson