Currently HPET ACPI table is created regardless of whether qemu actually
created hpet device. This may confuse some guests that don't check that
hpet is functional before using it. Solve this by passing info about
hpets in qemu to seabios via fw config interface. Additional benefit is
that seabios no longer uses hard coded hpet configuration. Proposed
interface supports up to 8 hpets. This is the number defined by hpet
spec.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
The capability register is read-only from guest POV, so we do not need
to update it on reset.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Change #define DEBUG to #define E1000_DEBUG in hw/e1000.c to make
it possible to build QEMU with -DDEBUG
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Remove unused DEBUG defines from hw/msix.c to avoid having anything
define the word DEBUG without any additions such as MSIX_DEBUG.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This implements the HPET capability of routing IRQs to the front-side
bus, aka MSI support. This feature can be enabled via the qdev property
"msi" and is off by default.
Note that switching it on can cause guests (at least Linux) to use the
HPET as timer instead of the LAPIC. KVM users should recall that only
the latter is currently available as fast in-kernel model.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
One HPET block supports up to 32 timers. Allow to instantiate more than
the recommended and implemented minimum of 3. The number is configured
via the qdev property "timers". It is also saved/restored so that it
need not match between migration peers.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
By implementing this feature we can also remove a nasty way to kill qemu
(by trying to enable level-triggered hpet interrupts).
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Instead of keeping a static reference around, pass the state to
hpet_enabled and hpet_get_ticks. All callers now have it at hand. Will
once allow to instantiate the HPET more than a single time.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Allow the intercept the RTC IRQ for the HPET legacy mode. Then push
routing to IRQ8 completely into the HPET. This allows to turn
hpet_in_legacy_mode() into a private function. Furthermore, this stops
the RTC from clearing IRQ8 even if the HPET is in control.
This patch comes with a side effect: The RTC timers will no longer be
stoppend when there is no IRQ consumer, possibly causing a minor
performance degration. But as the guest may want to redirect the RTC to
the SCI in that mode, it should normally disable unused IRQ source
anyway.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
We have to update the qemu timer when the per-timer enable bit is
toggled, just like for HPET_CFG_ENABLE changes.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Register the HPET as a sysbus device and create it that way. As it can
route its IRQs to any ISA IRQ, we need to connect it to all 24 of them.
Once converted to qdev, we can move reset handler and vmstate
registration into its hands as well.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Properly initialize HPETTimer::tn and HPETTimer::state once during
hpet_init instead of (re-)writing them on every reset.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Setting the main counter while the HPET is enabled may not be a good
idea of the guest, but it is supported and should, thus, not spam the
host console with warnings.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This moves the private HPET structures into the C module, simplifies
some helper functions and fixes most coding style issues (biggest chunk
was improper switch-case indention). No functional changes.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Also prevent out-of-bounds write access to the timers but don't spam the
host console if it triggers.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
42f1ced228 removed irq lowering
during reset. However, for chip reset command and DMA reset signal,
its actually the correct thing to do.
Lower IRQ on soft reset only.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
BusState::name is allocated in qbus_create_inplace().
So it should be freed by qbus_free().
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This patch fixes the following compilation errors in multiboot.c
when DEBUG_MULTIBOOT is defined.
Use TARGET_FMT_plx instead of %x for target_phys_addr_t.
CC i386-softmmu/multiboot.o
cc1: warnings being treated as errors
qemu/hw/multiboot.c: In function 'mb_add_mod':
qemu/hw/multiboot.c:121: error: format '%08x' expects type 'unsigned int', but argument 4 has type 'target_phys_addr_t'
qemu/hw/multiboot.c:121: error: format '%08x' expects type 'unsigned int', but argument 5 has type 'target_phys_addr_t'
qemu/hw/multiboot.c: In function 'load_multiboot':
qemu/hw/multiboot.c:279: error: format '%#x' expects type 'unsigned int', but argument 5 has type 'target_phys_addr_t'
qemu/hw/multiboot.c:307: error: format '%x' expects type 'unsigned int', but argument 3 has type 'target_phys_addr_t'
qemu/hw/multiboot.c:308: error: format '%x' expects type 'unsigned int', but argument 3 has type 'target_phys_addr_t'
make[1]: *** [multiboot.o] Error 1
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
virtio net attempts to peek into virtio queue to
determine that we have enough space for the complete
packet to fit. However, it fails to account for space
consumed by virtio net header when it does this,
under stress this results in a failure
with the message 'truncating packet'.
redhat bz 591494.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Anything that moves hundreds of lines out of vl.c can't be all bad.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Show the actual default value instead of <null> when the property has
not been set.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
It needs to be a qdev property, because it belongs to the drive's
guest part.
Bonus: info qtree now shows the serial number.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Show the actual default value instead of <null> when the property has
not been set.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
It needs to be a qdev property, because it belongs to the drive's
guest part.
Bonus: info qtree now shows the serial number.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
parse_string() qemu_strdup()s the property value. It is never freed.
It needs to be freed along with the device. Otherwise, the value of
scsi-disk property "ver" gets leaked when hot-unplugging the disk, for
instance.
Call new PropertyInfo method free() from qdev_free(). Implement it
for qdev_prop_string.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
IDEState members drive_serial_str and version are now left empty until
an actual drive is connected. Before, they got a default value that
was overwritten when a drive got connected. Doesn't matter, because
they're used only while a drive is connected.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Commit 428c149b added IDEState member conf to let commit 0009baf1 find
the BlockConf from there. It exists only for qdev drives, created via
ide_drive_initfn(), not for drives created via ide_init2().
But for a qdev drive, we can just as well reach its IDEDevice, which
contains the BlockConf. Do that, and revert the parts of commit
428c149b that add IDEState member conf.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Clean up virtio-blk.c to be more consistent using BDRV_SECTOR_SIZE
instead of hard coded 512 values.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
vhost net currently keeps running after vmstop,
which causes trouble as qemy does not check
for dirty pages anymore.
The fix is to simply keep vm and vhost running/stopped
status in sync.
Tested-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Previous commit added QMP documentation to the qemu-monitor.hx
file, it's is a copy of this information.
While it's good to keep it near code, maintaining two copies of
the same information is too hard and has little benefit as we
don't expect client writers to consult the code to find how to
use a QMP command.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Fix for too small allocation to ports_map
Signed-off-by: Alon Levy <alevy@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Booting an arm kernel has been broken a while when booting from non zero start
address. This is due to the order of events: board init loads the kernel and
sets register 15 to the start address and then qemu_system_reset reset the cpu
making register 15 zero again.
This patch fixes the usage of the register 15 start address trick in
combination with arm_load_kernel.
Signed-off-by: Lars Munch <lars@segv.dk>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
add helper function which converts root bus to pci domain.
make them aware of pci domain.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Gleb Natapov
Jan Kiszka
Jes Sorensen
Anthony Liguori
Paul Brook
Blue Swirl
Isaku Yamahata
Edgar E. Iglesias
Nathan Froyd
Michael S. Tsirkin
Markus Armbruster
Luiz Capitulino
Alon Levy
Lars Munch