This adds the SiI9022 (and implicitly EDID I2C) device to the ARM
Versatile Express machine, and selects the two I2C devices necessary
in the arm-softmmu.mak configuration so everything will build
smoothly.
I am implementing proper handling of the graphics in the Linux
kernel and adding proper emulation of SiI9022 and EDID makes the
driver probe as nicely as before, retrieving the resolutions
supported by the "QEMU monitor" and overall just working nice.
Cc: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Message-id: 20180227104903.21353-6-linus.walleij@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This adds support for emulating the Silicon Image SII9022 DVI/HDMI
bridge. It's not very clever right now, it just acknowledges
the switch into DDC I2C mode and back. Combining this with the
existing DDC I2C emulation gives the right behavior on the Versatile
Express emulation passing through the QEMU EDID to the emulated
platform.
Cc: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Message-id: 20180227104903.21353-5-linus.walleij@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: explictly reset ddc_req/ddc_skip_finish/ddc]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The tx function of the DDC I2C slave emulation was returning 1
on all writes resulting in NACK in the I2C bus. Changing it to
0 makes the DDC I2C work fine with bit-banged I2C such as the
versatile I2C.
I guess it was not affecting whatever I2C controller this was
used with until now, but with the Versatile I2C it surely
does not work.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Message-id: 20180227104903.21353-4-linus.walleij@linaro.org
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some devices need access to it.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Message-id: 20180227104903.21353-3-linus.walleij@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use 8 dummy cycles (4 dummy bytes) with the QIOR/QIOR4 commands in legacy mode
for matching what is expected by Micron (Numonyx) flashes (the default target
flash type of the QSPI).
Signed-off-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Tested-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180223232233.31482-3-frasse.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Assert only the lower cs on bus 0 and upper cs on bus 1 when both buses and
chip selects are enabled (e.g reading/writing with stripe).
Signed-off-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Tested-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180223232233.31482-2-frasse.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Ensure that the post write hook is called during reset. This allows us
to rely on the post write functions instead of having to call them from
the reset() function.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: d131e24b911653a945e46ca2d8f90f572469e1dd.1517856214.git.alistair.francis@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Due to a kernel bug we can never increase the size of capability
set 1, so introduce a new capability set in parallel, old userspace
will continue to use the old set, new userspace will start using
the new one when it detects a fixed kernel.
v2: don't use a define from virglrenderer, just probe it.
v3: fix compilation when virglrenderer disabled
v4: fix style warning, just use ?: op instead.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Message-id: 20180223023814.24459-1-airlied@gmail.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This patch implements a dummy ObjectInfo structure so that
it's easy to typecast the incoming data. If the metadata is
valid, write_pending is set. Also, the incoming filename
is utf-16, so, instead of depending on external libraries, just
implement a simple function to get the filename
Signed-off-by: Bandan Das <bsd@redhat.com>
Message-id: 20180223164829.29683-6-bsd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Allow write operations on behalf of the initiator. The
precursor to write is the sending of the write metadata
that consists of the ObjectInfo dataset. This patch introduces
a flag that is set when the responder is ready to receive
write data based on a previous SendObjectInfo operation by
the initiator (The SendObjectInfo implementation is in a
later patch)
Signed-off-by: Bandan Das <bsd@redhat.com>
Message-id: 20180223164829.29683-5-bsd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Write of existing objects by the initiator is acheived by
making a temporary buffer with the new changes, deleting the
old file and then writing a new file with the same name.
Also, add a "readonly" property which needs to be set to false
for deletion to work.
Signed-off-by: Bandan Das <bsd@redhat.com>
Message-id: 20180223164829.29683-4-bsd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Fix a possible null dereference when deleting a folder and
its contents. An ignored event might be received for its contents
after the parent folder is deleted which will return a null object.
Signed-off-by: Bandan Das <bsd@redhat.com>
Message-id: 20180223164829.29683-3-bsd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The response to a SendObjectInfo consists of the storageid,
parent obejct handle and the handle reserved for the new
incoming object
Signed-off-by: Bandan Das <bsd@redhat.com>
Message-id: 20180223164829.29683-2-bsd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215221325.7611-15-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215221325.7611-14-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215221325.7611-13-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Suggested-by: Alistair Francis <alistair.francis@xilinx.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215221325.7611-12-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
returning sd_illegal, since they are not implemented.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215221325.7611-11-f4bug@amsat.org
[PMM: tweak multiline comment format]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Linux uses it to poll the bus before polling for a card.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215221325.7611-10-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215221325.7611-9-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
use the registerfields API to access the OCR register
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215221325.7611-8-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
the code is easier to review/refactor.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215221325.7611-7-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This device does not model MMCA Specification previous to v4.2
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215221325.7611-6-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215221325.7611-5-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
To comply with Spec v1.10 (and 2.00, 3.01):
. TRAN_SPEED
for current SD Memory Cards that field must be always 0_0110_010b (032h) which is
equal to 25MHz - the mandatory maximum operating frequency of SD Memory Card.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215221325.7611-4-f4bug@amsat.org
[PMM: fixed comment indent]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215221325.7611-3-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Don't set the high capacity bit by default as it will be set if required
in the sd_set_csd() function.
[based on a patch from Alistair Francis <alistair.francis@xilinx.com>
and Peter Ogden <ogden@xilinx.com> from qemu/xilinx tag xilinx-v2015.4]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215221325.7611-2-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215220540.6556-12-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
code is now easier to read.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215220540.6556-11-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215220540.6556-8-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215220540.6556-6-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215220540.6556-5-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180215220540.6556-4-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215220540.6556-3-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
place card registers first, this will ease further code movements.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215220540.6556-2-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
On reset the bus will reset the card,
we can now drop the device_reset() call.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180216022933.10945-5-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
using the sdbus_*() API.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Acked-by: Michael Walle <michael@walle.cc>
Message-id: 20180216022933.10945-4-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Create the SDCard in the realize() function.
Suggested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Acked-by: Michael Walle <michael@walle.cc>
Message-id: 20180216022933.10945-3-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Acked-by: Michael Walle <michael@walle.cc>
Message-id: 20180216022933.10945-2-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some register blocks of the ast2500 are protected by protection key
registers which require the right magic value to be written to those
registers to allow those registers to be mutated.
Register manuals indicate that writing the correct magic value to these
registers should cause subsequent reads from those values to return 1,
and writing any other value should cause subsequent reads to return 0.
Previously, qemu implemented these registers incorrectly: the registers
were handled as simple memory, meaning that writing some value x to a
protection key register would result in subsequent reads from that
register returning the same value x. The protection was implemented by
ensuring that the current value of that register equaled the magic
value.
This modifies qemu to have the correct behaviour: attempts to write to a
ast2500 protection register results in a transition to 1 or 0 depending
on whether the written value is the correct magic. The protection logic
is updated to ensure that the value of the register is nonzero.
This bug caused deadlocks with u-boot HEAD: when u-boot is done with a
protectable register block, it attempts to lock it by writing the
bitwise inverse of the correct magic value, and then spinning forever
until the register reads as zero. Since qemu implemented writes to these
registers as ordinary memory writes, writing the inverse of the magic
value resulted in subsequent reads returning that value, leading to
u-boot spinning forever.
Signed-off-by: Hugo Landau <hlandau@devever.net>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 20180220132627.4163-1-hlandau@devever.net
[PMM: fixed incorrect code indentation]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
I/O currently being synchronous, there is no reason to ever clear the
SR_TXE bit. However the SR_TC bit may be cleared by software writing
to the SR register, so set it on each write.
In addition, fix the reset value of the USART status register.
Signed-off-by: Richard Braun <rbraun@sceen.net>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
[PMM: removed XXX tag from comment, since it isn't something
we need to come back and fix in QEMU]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch adds a "raspi3" machine type, which can now be selected as
the machine to run on by users via the "-M" command line option to QEMU.
The machine type does *not* ignore memory transaction failures so we
likely need to add some dummy devices later when people run something
more complicated than what I'm using for testing.
Signed-off-by: Pekka Enberg <penberg@iki.fi>
[PMM: added #ifdef TARGET_AARCH64 so we don't provide the 64-bit
board in the 32-bit only arm-softmmu build.]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Leak found thanks to ASAN:
Direct leak of 8 byte(s) in 1 object(s) allocated from:
#0 0x55995789ac90 in __interceptor_malloc (/home/elmarco/src/qemu/build/x86_64-softmmu/qemu-system-x86_64+0x1510c90)
#1 0x7f0a91190f0c in g_malloc /home/elmarco/src/gnome/glib/builddir/../glib/gmem.c:94
#2 0x5599580a281c in v9fs_path_copy /home/elmarco/src/qemu/hw/9pfs/9p.c:196:17
#3 0x559958f9ec5d in coroutine_trampoline /home/elmarco/src/qemu/util/coroutine-ucontext.c:116:9
#4 0x7f0a8766ebbf (/lib64/libc.so.6+0x50bbf)
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
lhs/rhs doesn't tell much about how argument are handled, dst/src is
and const arguments is clearer in my mind. Use g_memdup() while at it.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
Linus Walleij
Corey Minyard
Francisco Iglesias
Alistair Francis
Peter Maydell
Dave Airlie
Bandan Das
Philippe Mathieu-Daudé
Hugo Landau
Richard Braun
Pekka Enberg
Marc-André Lureau