Limit MIPS16 instruction disassembly according to the ISA level and ASE
set selected, as with the regular MIPS and microMIPS instruction sets.
Retain the property of `objdump -m mips:16' disassembling all MIPS16
instructions however, regardless of any ISA level recorded in the binary
examined.
To validate the disassembler use the GAS test suite for its convenience
of running tests across multiple ISAs, even though placing the tests in
the binutils test suite would be more appropriate. Adjust the single
binutils test which depends on 64-bit instruction disassembly to have
the ISA level required actually recorded in the binary examined.
opcodes/
* mips-dis.c (mips_arch_choices): Use ISA_MIPS64 rather than
ISA_MIPS3 as the `isa' selection in the `bfd_mach_mips16' entry.
(print_insn_mips16): Check opcode entries for validity against
the ISA level and ASE set selected.
binutils/
* testsuite/binutils-all/mips/mips16-undecoded.s: Use `.module'
rather than `.set' to set the ISA level.
gas/
* testsuite/gas/mips/mips16-sub.d: New test.
* testsuite/gas/mips/mips16-32@mips16-sub.d: New test.
* testsuite/gas/mips/mips16e-32@mips16-sub.d: New test.
* testsuite/gas/mips/mips16e-sub.d: New test.
* testsuite/gas/mips/mips16-32@mips16e-sub.d: New test.
* testsuite/gas/mips/mips16-64@mips16e-sub.d: New test.
* testsuite/gas/mips/mips16e-64-sub.d: New test.
* testsuite/gas/mips/mips16-32@mips16e-64-sub.d: New test.
* testsuite/gas/mips/mips16-64@mips16e-64-sub.d: New test.
* testsuite/gas/mips/mips16e-32@mips16e-64-sub.d: New test.
* testsuite/gas/mips/mips16-sub.s: New test source.
* testsuite/gas/mips/mips16e-sub.s: New test source.
* testsuite/gas/mips/mips16e-64-sub.s: New test source.
* testsuite/gas/mips/mips.exp: Run the new tests.
Switch to 32-bit MIPS16 opcode table entry interpretation, similar to
how the microMIPS opcode table is handled, for both the `match' and
`mask' fields, removing special casing for JAL and JALX instructions and
their `a' and `i' operand codes throughout, while retaining automatic
processing of extendable opcodes in assembly and disassembly.
In assembly disallow size enforcement suffixes as appropriate: `.t' for
both 32-bit instructions and macros and `.e' for macros only, making
macro handling consistent with the microMIPS instruction set.
In disassembly fully decode EXTEND prefixes prepended to unsupported
instruction encodings (according to the ISA selection) rather than
dumping them as hexadecimal data along with the following instruction,
removing all special casing for the EXTEND prefix and making its
handling rely on its opcode table entry, except where it is considered a
part of an extendable instruction.
include/
* opcode/mips.h (mips_opcode_32bit_p): New inline function.
gas/
* config/tc-mips.c (micromips_insn_length): Use
`mips_opcode_32bit_p'.
(is_size_valid): Adjust description.
(is_size_valid_16): New function.
(validate_mips_insn): Use `mips_opcode_32bit_p' in MIPS16
operand decoding.
(validate_mips16_insn): Remove `a' and `i' operand code special
casing, use `mips_opcode_32bit_p' to determine instruction
width.
(append_insn): Adjust forced MIPS16 instruction size
determination.
(match_mips16_insn): Likewise. Don't shift the instruction's
opcode with the `a' and `i' operand codes. Use
`mips_opcode_32bit_p' in operand decoding.
(match_mips16_insns): Check for forced instruction size's
validity.
(mips16_ip): Don't force instruction size in the `noautoextend'
mode.
* testsuite/gas/mips/mips16-jal-e.d: New test.
* testsuite/gas/mips/mips16-jal-t.d: New test.
* testsuite/gas/mips/mips16-macro-e.d: New test.
* testsuite/gas/mips/mips16-macro-t.d: New test.
* testsuite/gas/mips/mips16-jal-t.l: New stderr output.
* testsuite/gas/mips/mips16-macro-e.l: New stderr output.
* testsuite/gas/mips/mips16-macro-t.l: New stderr output.
* testsuite/gas/mips/mips16-jal-e.s: New test source.
* testsuite/gas/mips/mips16-jal-t.s: New test source.
* testsuite/gas/mips/mips16-macro-e.s: New test source.
* testsuite/gas/mips/mips16-macro-t.s: New test source.
* testsuite/gas/mips/mips.exp: Run the new tests.
opcodes/
* mips-dis.c (print_mips16_insn_arg): Always handle `extend' and
`insn' together, with `extend' as the high-order 16 bits.
(match_kind): New enum.
(print_insn_mips16): Rework for 32-bit instruction matching.
Do not dump EXTEND prefixes here.
* mips16-opc.c (mips16_opcodes): Move "extend" entry to the end.
Recode `match' and `mask' fields as 32-bit in absolute "jal" and
"jalx" entries.
binutils/
* testsuite/binutils-all/mips/mips16-extend-noinsn.d: Adjust
test for separate EXTEND prefix disassembly.
We've decided to standardize on two flags for RISC-V: "-march" sets the
target architecture (which determines which instructions can be
generated), and "-mabi" sets the target ABI. We needed to rework this
because the old flag set didn't support soft-float or single-float ABIs,
and didn't support an x32-style ABI on RISC-V.
Additionally, we've changed the behavior of the -march flag: it's now a
lot stricter and only parses things we can actually understand.
Additionally, it's now lowercase-only: the rationale is that while the
RISC-V ISA manual specifies that ISA strings are case-insensitive, in
Linux-land things are usually case-sensitive. Since this flag can be
used to determine library paths, we didn't want to bake some
case-insensitivity in there that would case trouble later.
This patch implements these two new flags and removes the old flags that
could conflict with these. There wasn't a RISC-V release before, so we
want to just support a clean flag set.
include/
* elf/riscv.h (EF_RISCV_SOFT_FLOAT): Don't define.
(EF_RISCV_FLOAT_ABI, EF_RISCV_FLOAT_ABI_SOFT): Define.
(EF_RISCV_FLOAT_ABI_SINGLE, EF_RISCV_FLOAT_ABI_DOUBLE): Define.
(EF_RISCV_FLOAT_ABI_QUAD): Define.
bfd/
* elfnn-riscv.c (_bfd_riscv_elf_merge_private_bfd_data): Use
EF_RISCV_FLOAT_ABI_SOFT instead of EF_RISCV_SOFT_FLOAT.
binutils/
* readelf.c (get_machine_flags): Use
EF_RISCV_FLOAT_ABI_{SOFT,SINGLE,DOBULE,QUAD) instead of
EF_RISCV_{SOFT,HARD}_FLOAT.
gas/
* config/tc-riscv.h (xlen): Delete.
* config/tc-riscv.c (xlen): Make static.
(abi_xlen): New variable.
(options): Replace OPTION_{M32,M64,MSOFT_FLOAT,MHARD_FLOAT,MRVC}
with OPTION_MABI.
(md_longopts): Likewise.
(md_parse_option): Likewise.
(riscv_elf_final_processing): Likewise.
* doc/as.texinfo (Target RISC-V options): Likewise.
* doc/c-riscv.texi (OPTIONS): Likewise.
* config/tc-riscv.c (float_mode): Removed.
(float_abi): New type, specifies the floating-point ABI.
(riscv_set_abi): New function.
(riscv_add_subset): Only allow lower-case ISA names and require
them to start with "rv".
(riscv_after_parse_args): Likewise.
opcodes/
* riscv-dis.c (riscv_disassemble_insn): Default to the ELF's
XLEN when none is provided.
Respect any ASE flags recorded in ELF file structures for the purpose of
selecting instructions to be disassembled, preventing code from being
hex-dumped even though having been clearly indicated as valid at the
assembly time. Use date from the MIPS ABI flags structure if present,
and otherwise there may be an MDMX ASE flag set in the ELF file header.
For backwards compatibility only set extra flags and do not clear any,
preserving all previously set by the architecture selected to be
disassembled for.
include/
* elf/mips.h (Elf_Internal_ABIFlags_v0): Also declare struct
typedef as `elf_internal_abiflags_v0'.
bfd/
* bfd-in.h (elf_internal_abiflags_v0): New struct declaration.
(bfd_mips_elf_get_abiflags): New prototype.
* elfxx-mips.c (bfd_mips_elf_get_abiflags): New function.
* bfd-in2.h: Regenerate.
opcodes/
* mips-dis.c (mips_convert_abiflags_ases): New function.
(set_default_mips_dis_options): Also infer ASE flags from ELF
file structures.
binutils/
* testsuite/binutils-all/mips/mips-ase-1.d: New test.
* testsuite/binutils-all/mips/mips-ase-2.d: New test.
* testsuite/binutils-all/mips/mips-ase-3.d: New test.
* testsuite/binutils-all/mips/mips-ase-1.s: New test source.
* testsuite/binutils-all/mips/mips-ase-2.s: New test source.
* testsuite/binutils-all/mips/mips.exp: Run the new tests.
Use a tab rather than a space to separate `extend' and its uninterpreted
argument output, like with regular instructions. Separate hexadecimal
halves of undecoded extended instructions output with a space instead of
presenting them concatenated.
opcodes/
* mips-dis.c (print_insn_mips16): Use a tab rather than a space
to separate `extend' and its uninterpreted argument output.
Separate hexadecimal halves of undecoded extended instructions
output.
binutils/
* testsuite/binutils-all/mips/mips16-extend-noinsn.d: New test.
* testsuite/binutils-all/mips/mips16-extend-noinsn.s: New test
source.
* testsuite/binutils-all/mips/mips.exp: Run the new test.
Complement commit dd8b7c222e ("MIPS: mips16e jalrc/jrc opcodes"),
<https://sourceware.org/ml/binutils/2005-07/msg00349.html>, and stop the
disassembler making a delay-slot adjustment for PC-relative operations
following either MIPS16e compact jumps, or undefined RR/J(AL)R(C)
encodings that have the `l' (link) and `ra' (source register is `ra')
bits set both at a time. Adjust code description for accuracy. Add a
suitable test case.
opcodes/
* mips-dis.c (print_mips16_insn_arg): Avoid delay-slot
adjustment for PC-relative operations following MIPS16e compact
jumps or undefined RR/J(AL)R(C) encodings.
binutils/
* testsuite/binutils-all/mips/mips16-pcrel.d: New test.
* testsuite/binutils-all/mips/mips16-pcrel.s: New test source.
* testsuite/binutils-all/mips/mips.exp: Run the new test.
PR binutils/20930
* objcopy.c (mark_symbols_used_in_relocations): Check for a null
symbol pointer pointer before attempting to mark the symbol as
kept.
The attached patch fixes a problem where nm displays bogus information for
synthetic symbol sizes when --size-sort is used.
This happens because the synthetic symbols (dot symbols for ppc64) are
generated based on their non-dot symbols. The generation process doesn't copy
over the ELF-specific bits of the regular non-dot symbols.
When --size-sort is used, the code attempts to access the symbol size from
the ELF-specific bits and ends up reading gargabe, causing the size to be
displayed incorrectly.
With the patch, i can see dot and non-dot symbols having the same size with
--size-sort.
This doesn't fix the fact that we don't display size information for synthetic
symbols without --size-sort, which i may address in the future.
binutils/ChangeLog:
2016-12-01 Luis Machado <lgustavo@codesourcery.com>
* nm.c (sort_symbols_by_size): Don't read symbol size if symbol
is synthetic.
This patch fixes:
- fpus and fpud are swaped.
- quarkse_em doesn't include FPX extensions.
- auto guessed opcode mechanism may ignore the option passed via -M<feature> option.
opcodes/
2016-11-29 Claudiu Zissulescu <claziss@synopsys.com>
* arc-dis.c (is_compatible_p): Remove function.
(skip_this_opcode): Don't add any decoding class to decode list.
Remove warning.
(find_format_from_table): Go through all opcodes, and warn if we
use a guessed mnemonic.
binutils/
2016-11-29 Claudiu Zissulescu <claziss@synopsys.com>
* testsuite/binutils-all/arc/objdump.exp (Warning test): Update
test.
PR ld/20815
bfd * elf.c (elf_modify_segment_map): Allow empty LOAD segments if
they contain the program headers.
(_bfd_elf_map_sections_to_segments): If the linker created the
PHDR segment then always attempt to include it in a LOAD segment.
(assign_file_positions_for_non_load_sections): Allow LOAD segments
to overlap PHDR segments.
(phdr_sorter): New function. Sorts program headers.
(assign_file_positions_except_relocs): Sort the program headers
before writing them out. Issue an error if the PHDR segment is
not covered by a LOAD segment, unless the backend allows it.
* elf-bfd.h (struct elf_backend_data): Add
elf_backend_allow_non_load_phdr.
* elfxx-target.h (elf_backend_allow_non_load_phdr): Provide
default definition that returns FALSE.
(elfNN_bed): Initialise the elf_backend_allow_non_load_phdr
field.
* elf64-hppa.c (elf64_hppa_allow_non_load_phdr): New function.
Returns TRUE.
(elf_backend_allow_non_load_phdr): Define.
* elf-m10300.c (_bfd_mn10300_elf_size_dynamic_sections): Do not
place the interpreter string into the .interp section if the
nointerp flag is set in the link info structure.
* elf32-arc.c (elf_arc_size_dynamic_sections): Likewise.
* elf32-score7.c (score_elf_final_link_relocate): Allow for the
_gp symbol not being part of the output.
binutils* readelf.c (process_program_headers): Check PT_LOAD and PT_PHDR
segments for validity.
ld * ld.texinfo: Note that PT_TLS can be used as a segment type.
* testsuite/ld-discard/discard.ld: Add space for program headers.
* testsuite/ld-elf/flags1.ld: Likewise.
* testsuite/ld-elf/maxpage3.t: Likewise.
* testsuite/ld-elf/noload-1.t: Likewise.
* testsuite/ld-elf/orphan.ld: Likewise.
* testsuite/ld-elf/overlay.t: Likewise.
* testsuite/ld-elf/pr14052.t: Likewise.
* testsuite/ld-elf/pr19539.t: Likewise.
* testsuite/ld-elf/provide-hidden-1.ld: Likewise.
* testsuite/ld-elf/provide-hidden-s.ld: Likewise.
* testsuite/ld-elf/weak-dyn-1.ld: Likewise.
* testsuite/ld-i386/pr19539.t: Likewise.
* testsuite/ld-scripts/defined.t: Likewise.
* testsuite/ld-scripts/defined6.t: Likewise.
* testsuite/ld-scripts/dynamic-sections.t: Likewise.
* testsuite/ld-scripts/empty-aligned.t: Likewise.
* testsuite/ld-scripts/provide-2.t: Likewise.
* testsuite/ld-scripts/provide-4.t: Likewise.
* testsuite/ld-vax-elf/plt-local.ld: Likewise.
* testsuite/ld-x86-64/pr19539.t: Likewise.
* testsuite/ld-elf/ehdr_start-missing.d: Do not initialise the
dynamic linker.
* testsuite/ld-elf/ehdr_start-weak.d: Likewise.
* testsuite/ld-elf/elf.exp (pr14170, pr17068): Likewise.
* testsuite/ld-elf/loadaddr1.d: Update expected readelf output.
* testsuite/ld-elf/noload-2.d: Likewise.
* testsuite/ld-powerpc/vxworks2.sd: Likewise.
* testsuite/ld-scripts/phdrs3a.d: Likewise.
* testsuite/ld-scripts/size-2.d: Likewise.
* testsuite/ld-elf/group.ld: Add program headers.
* testsuite/ld-elf/overlay.d: Skip for SPU.
* testsuite/ld-elf/flags1.d: Skip for RX.
* testsuite/ld-elf/pr19162.d: Skip for HPPA64.
* testsuite/ld-elf/pr19539.d: Skip for ALPHA.
* testsuite/ld-scripts/empty-orphan.t: Update program headers.
* testsuite/ld-scripts/size-2.t: Likewise.
PR binutils/20814
* dlltool.c (struct export): Remove hint field.
(make_one_lib_file): Store the ordinal value for IDATA6 not the
hint.
(gen_lib_file): Delete reference to hint field.
(mangle_defs): Delete computation of hint field.
PR binutils/20751
* nm.c (with_symbol_versions): New local variable.
(long_options): Add --with-symbol-versions.
(usage): Mention --with-symbol-versions.
(print_symbol): If with_symbol_versions is set then display the
version information associated with the symbol.
* NEWS: Mention the new feature.
* doc/binutils.texi (nm): Document the new option.
(objdump): Describe how symbol version information is displayed
for dynamic symbol dumps.
(readelf): Describe how symbol version information is displayed.
* testsuite/binutils-all/nm.exp: Add a test of the new feature.
I've been using dwarf-mode.el again recently and I found it mildly
annoying that the mode doesn't set default-directory. Setting it
means that operations in the dwarf-browsing buffer default to the
directory holding the object file being investigated.
This bumps the version number as well so that updating it via the
package manager works properly.
2016-11-04 Tom Tromey <tom@tromey.com>
* dwarf-mode.el (dwarf-browse): Set default-directory. Bump
version number.
* readelf.c (apply_relocations): Fail if the symbol table section
linked to by the reloc section does not have either the SHT_SYMTAB
or SHT_DYNSYM type.
(print_gnu_note): Decode the contents of NT_GNU_HWCAP notes.
Print the contents of unknown note types.
(process_note): Add the file and section to the parameter list.
Use print_symbol to display the note name.
Display the contents of unknown note types.
(process_corefile_note_segment): Rename to process_notes_at.
Add section parameter. Apply relocations to the notes when
loading from a section. Display section name when processing
notes in a section.
* testsuite/binutils-all/readelf.n: Update expected output.
As pointed out in PR binutils/19020, those tests were still failing when doing
remote testing. This is because the binary files weren't being copied over to
the remote host for testing.
FAIL: binutils-all/pr19020a
FAIL: binutils-all/pr19020b
This small patch fixes this up to make things pass.
binutils/ChangeLog:
2016-10-14 Luis Machado <lgustavo@codesourcery.com>
* testsuite/lib/utils-lib.exp (run_dump_test): Call remote_download
to copy file to remote host.
On S/390 we see quite often registers marked as "bad register" in the
readelf --debug-dump=frames or objdump -Wf output.
00000000 0000000000000014 00000000 CIE
Version: 1
Augmentation: "zR"
Code alignment factor: 1
Data alignment factor: -8
Return address column: 14
Augmentation data: 1b
DW_CFA_def_cfa: r15 ofs 160
DW_CFA_nop
DW_CFA_nop
DW_CFA_nop
...
00000050 000000000000001c 00000054 FDE cie=00000000 pc=0000000080000e58..0000000080000e84
DW_CFA_advance_loc: 6 to 0000000080000e5e
DW_CFA_offset: r14 at cfa-48
DW_CFA_offset: r15 at cfa-40
DW_CFA_advance_loc: 6 to 0000000080000e64
DW_CFA_def_cfa_offset: 320
DW_CFA_advance_loc: 18 to 0000000080000e76
DW_CFA_restore: bad register: r15 <------
DW_CFA_restore: r14
DW_CFA_def_cfa_offset: 160
This is triggered by this check in display_debug_frames (dwarf.c):
case DW_CFA_restore:
if (opa >= (unsigned int) cie->ncols
|| opa >= (unsigned int) fc->ncols)
reg_prefix = bad_reg;
cie->ncols is number of registers referenced in the CIE which is 15 due
to r14 being given as return address column. So for the CFA_restore of
r15 a "bad register" is being printed while the same rule on r14 is ok.
The reason for this check is to prevent wild memory accesses when
reading input with corrupted register values while accessing the
col_type/col_offset arrays. However in that case r15 is a perfectly
valid register. It just happens not to be mentioned in the CIE. Hence
restoring the CIE rule for r15 should end up with the default rule which
is DW_CFA_undefined.
This probably wasn't observed on other platforms because they either do
not use CFA_restore (x86-64) or do not issue CFA_restore on registers
with a higher number than the return address column.
binutils/ChangeLog:
2016-09-29 Andreas Krebbel <krebbel@linux.vnet.ibm.com>
* dwarf.c (frame_display_row): Fix formatting of return address
register column.
(display_debug_frames): Ignore invalid indices into
cie->col_type/cie->col_offset arrays and default to
DW_CF_undefined instead.
This patch adds support for .cfi_val_offset GAS pseudo command which
maps to DW_CFA_val_offset and DW_CFA_val_offset_sf.
gas/ChangeLog:
2016-09-29 Andreas Krebbel <krebbel@linux.vnet.ibm.com>
* doc/as.texinfo: Add docu for .cfi_val_offset.
* dw2gencfi.c (cfi_add_CFA_val_offset): New function.
(dot_cfi): Add case for DW_CFA_val_offset.
(output_cfi_insn): Likewise.
(cfi_pseudo_table): Add entry for cfi_val_offset.
* dw2gencfi.h: Add prototype for cfi_add_CFA_val_offset.
* testsuite/gas/cfi/cfi-common-8.d: New test.
* testsuite/gas/cfi/cfi-common-8.s: New test.
* testsuite/gas/cfi/cfi.exp: Run cfi-common-8 testcase.
binutils/ChangeLog:
2016-09-29 Andreas Krebbel <krebbel@linux.vnet.ibm.com>
* dwarf.c (display_debug_frames): Adjust output line.
This patch extends Tag_GNU_Power_ABI_FP to cover long double ABIs,
makes the assembler warn about undefined tag values, and removes
similar warnings from the linker. I think it is better to not
warn in the linker about undefined tag values as future extensions to
the tags then won't result in likely bogus warnings. This is
consistent with the fact that an older linker won't warn on an
entirely new tag.
include/
* elf/ppc.h (Tag_GNU_Power_ABI_FP): Comment.
bfd/
* elf-bfd.h (_bfd_elf_ppc_merge_fp_attributes): Declare.
* elf32-ppc.c (_bfd_elf_ppc_merge_fp_attributes): New function.
(ppc_elf_merge_obj_attributes): Use it. Don't copy first file
attributes, merge them. Don't warn about undefined tag bits,
or copy unknown values to output.
* elf64-ppc.c (ppc64_elf_merge_private_bfd_data): Call
_bfd_elf_ppc_merge_fp_attributes.
binutils/
* readelf.c (display_power_gnu_attribute): Catch truncated section
for all powerpc attributes. Display long double ABI. Don't
capitalize words, except for names. Show known bits of tag values
when some unknown bits are present. Whitespace fixes.
gas/
* config/tc-ppc.c (ppc_elf_gnu_attribute): New function.
(md_pseudo_table <ELF>): Handle "gnu_attribute".
ld/
* testsuite/ld-powerpc/attr-gnu-4-4.s: Delete.
* testsuite/ld-powerpc/attr-gnu-4-14.d: Delete.
* testsuite/ld-powerpc/attr-gnu-4-24.d: Delete.
* testsuite/ld-powerpc/attr-gnu-4-34.d: Delete.
* testsuite/ld-powerpc/attr-gnu-4-41.d: Delete.
* testsuite/ld-powerpc/attr-gnu-4-32.d: Adjust expected warning.
* testsuite/ld-powerpc/attr-gnu-8-23.d: Likewise.
* testsuite/ld-powerpc/attr-gnu-4-01.d: Adjust expected output.
* testsuite/ld-powerpc/attr-gnu-4-02.d: Likewise.
* testsuite/ld-powerpc/attr-gnu-4-03.d: Likewise.
* testsuite/ld-powerpc/attr-gnu-4-10.d: Likewise.
* testsuite/ld-powerpc/attr-gnu-4-11.d: Likewise.
* testsuite/ld-powerpc/attr-gnu-4-20.d: Likewise.
* testsuite/ld-powerpc/attr-gnu-4-22.d: Likewise.
* testsuite/ld-powerpc/attr-gnu-4-33.d: Likewise.
* testsuite/ld-powerpc/attr-gnu-8-11.d: Likewise.
* testsuite/ld-powerpc/powerpc.exp: Don't run deleted tests.
get_coff_symbol_type had a potenial buffer overflow even with
untranslated messages.
* nm.c (get_elf_symbol_type): Don't use sprintf with translated
strings, use asprintf instead.
(get_coff_symbol_type): Likewise.
Symbol sorting means we can't assume that the last n symbols are
synthetic.
* nm.c (print_symbol): Remove is_synthetic param. Test sym->flags
instead.
(print_size_symbols, print_symbols): Adjust to suit, deleting
now unused synth_count param and fromsynth var.
(display_rel_file): Adjust, localizing synth_count.
Since the internal compression header size can be bigger than the
external compression header size, we should check the external
compression header size.
* readelf.c (load_specific_debug_section): Check the external
compression header size.
* readelf.c (process_symbol_table): Generate a warning if a local
symbol is found at and offste greater than or equal to the sh_info
field of it's section header.
PR binutils/20440
* dwarf.c (display_debug_lines_decoded): Add checks for running
off the end of the section when populating the directory table and
file table.
(frame_display_row): Set max_regs equal to ncols.
(load_specific_debug_section): If the section is compressed, but
it is not big enough to hold a compression header then warn and
return 0.
PR binutils/17512
* rescoff.c (read_coff_res_dir): Fix detection of buffer overrun.
* resbin.c (bin_to_res_version): Allow for the padded length of a
version block to be longer than the recorded length. Skip padding
bytes.
Some messing with plugin code in order to not need arelt_size in
ld code. File descriptor handling in ld/plugin.c is tidied too,
simply duping the open fd rather than opening the file again.
bfd/
* elflink.c: Include plugin-api.h.
* plugin.c (bfd_plugin_open_input): New function, extracted from..
(try_claim): ..here.
* plugin.h: Don't include bfd.h.
(bfd_plugin_open_input): Declare.
binutils/
* ar.c: Include plugin-api.h.
* nm.c: Likewise.
ld/
* plugin.c: Don't include libbfd.h. Include plugin-api.h
before bfd/plugin.h.
(plugin_object_p): Use bfd_plugin_open_input.
A rewrite of the code in bucomm.c supporting objdump -i, to use
bfd_iterate_over_targets rather than accessing bfd_target_vector
directly. Calculates widest arch string rather than using an
out of date constant. Stashes info from the first display of valid
target/arch combinations for use in second tabular display.
binutils/
* bucomm.c: Don't include libbfd.h.
(endian_string, display_target_list): Delete forward declaration.
(display_info_table, display_target_tables): Likewise.
(LONGEST_ARCH): Delete.
(struct display_target): New.
(do_display_target): New function.
(display_target_list, display_info): Rewrite functions.
(display_info_table): Delete.
(do_info_size, do_info_header, do_info_row): New functions.
Fix od-macho.c to use a leb128 function from binutils/dwarf.c rather
than one from bfd/libbfd.c.
binutils/
* elfcomm.h (HOST_WIDEST_INT): Move to..
* sysdep.h: ..here.
* od-macho.c: Don't include libbfd.h. Do include dwarf.h
(dump_dyld_info_rebase): Use read_leb128 rather than
read_unsigned_leb128.
(dump_dyld_info_bind, dump_dyld_info_export_1): Likewise.
(dump_segment_split_info): Likewise.
(dump_dyld_info): Rename vars to avoid shadowing dwarf.h enums.
(dump_load_command): Likewise.
Fixes failures on alpha, ia64, mcore, metag, moxie, and pj due to lack
of 16-bit relocs.
* testsuite/binutils-all/remove-relocs-01.s: Use .dc.a, not .word.
The objcopy and strip tools make use of the bfd library to manipulate
the state of the input file (to produce an output file). Within the
input file (for ELF at least), relocations are held within a section,
and so, if the user wanted to remove the relocations, but keep the
section to which the relocations would have been applied, it is tempting
to think that specifying the name of a relocation section to objcopy's
--remove-section option might do what you want, for example:
objcopy --remove-section=.rela.text input.elf output.elf
However, this does not work. The reason is that when the input file is
loaded, relocations are not managed as sections, but are, instead,
loaded as data associated with the section to which the relocations
would be applied. In our example above the relocations in '.rela.text'
are held as data on the section '.text' once 'input.elf' is loaded.
One task that objcopy and strip do is copy the relocations from the
input file to the output file if the section is also being copied from
the input file to the output file.
This commit adds a new command line option for objcopy and strip,
--remove-relocations, which can be used to remove the relocations, while
keeping the section that the relocations would have been applied to, for
example:
objcopy --remove-relocations=.text input.elf output.elf
in this case the section '.text' will appear in both 'input.elf' and
'output.elf', but any relocations in 'input.elf' that apply to '.text'
will not be present in 'output.elf'.
I have also added a special case to the handling of --remove-section
that spots if a user tries to remove a relocation section (currently
this is done by spotting the '.rela.' or '.rel.' prefix) and forwards
the request to --remove-relocations.
As with --remove-section and --only-section the --remove-relocations
option supports the '!' prefix on the section-patterns it takes to allow
for sections to be specifically not matched.
There are tests for all the new functionality.
binutils/ChangeLog:
* doc/binutils.texi (objcopy): Document 'remove-relocations'.
(strip): Likewise.
* objcopy.c (SECTION_CONTEXT_REMOVE_RELOCS): Define.
(enum command_line_switch): Add 'OPTION_REMOVE_RELOCS'.
(struct option strip_options): Add 'remove-relocations'.
(struct option copy_options): Likewise.
(copy_usage): Likewise.
(strip_usage): Likewise.
(handle_remove_relocations_option): New function.
(discard_relocations): New function.
(handle_remove_section_option): New function.
(copy_relocations_in_section): Use discard_relocations.
(strip_main): Use handle_remove_section_option for
'remove-section', and handle 'remove-relocations' option.
(copy_main): Likewise.
* testsuite/binutils-all/objcopy.exp: Run new tests.
* testsuite/binutils-all/remove-relocs-01.d: New file.
* testsuite/binutils-all/remove-relocs-01.s: New file.
* testsuite/binutils-all/remove-relocs-02.d: New file.
* testsuite/binutils-all/remove-relocs-03.d: New file.
* testsuite/binutils-all/remove-relocs-04.d: New file.
* testsuite/binutils-all/remove-relocs-05.d: New file.
* testsuite/binutils-all/remove-relocs-06.d: New file.
For symbol matching, prefixing a pattern with '!' will indicate a
non-matching pattern, however, this is not the case for section
patterns. As a result it is not possible to say "apply this action to
all sections except ...".
With this commit the objcopy and strip tools now support '!' prefix for
section patterns, so we can say:
objcopy --remove-section="*" --remove-section="!.text*"
Which will remove all sections, except those matching the pattern
'.text*'.
binutils/ChangeLog:
* objcopy.c (find_section_list): Handle section patterns starting
with '!' being a non-matching pattern.
* doc/binutils.texi (objcopy): Give example of using '!' with
--remove-section and --only-section.
(strip): Give example of using '!' with --remove-section.
* testsuite/binutils-all/data-sections.s: New file.
* testsuite/binutils-all/only-section-01.d: New file.
* testsuite/binutils-all/remove-section-01.d: New file.
* testsuite/binutils-all/objcopy.exp: Run new tests.
* NEWS: Mention new feature.
binutils/
PR binutils/20337
* objdump.c (compare_symbols): For ELF, sort same value/type
symbols according to size.
ld/
* testsuite/ld-powerpc/elfv2exe.d: Update.
binutuils* prdbg.c (pr_enum_type): Use a buffer big enough to hold an
extremely large decimal value.
(pr_range_type): Likewise.
(pr_array_type): Likewise.
(pr_struct_field): Likewise.
(pr_class_baseclass): Likewise.
(pr_class_method_variant): Likewise.
(pr_tag_type): Likewise.
(pr_int_constant): Likewise.
(pr_typed_constant): Likewise.
(pr_variable): Likewise.
(pr_function_parameter): Likewise.
(pr_start_block): Likewise.
(pr_lineno): Likewise.
(pr_end_block): Likewise.
(tg_enum_type): Likewise.
(tg_int_constant): Likewise.
(tg_typed_constant): Likewise.
(tg_start_block): Likewise.
gas * macro.c (macro_expand_body): Use a buffer big enough to hold an
extremely large integer.
* testsuite/binutils-all/objcopy.exp
(objcopy_test_without_global_symbol): Expect this test to fail on
the AArch64 and ARM targets, since they preserve their mapping
symbols.
Complement commit a43942db49 ("LD/ELF: Unify STB_GNU_UNIQUE handling")
and use `supports_gnu_unique' with the `unique_symbol' and `type' tests,
fixing failures like:
.../binutils/testsuite/binutils-all/unique.s: Assembler messages:
.../binutils/testsuite/binutils-all/unique.s:2: Error: symbol type "gnu_unique_object" is supported only by GNU targets
ERROR: .../binutils/testsuite/binutils-all/unique.s: assembly failed
UNRESOLVED: ar unique symbol in archive
.../binutils/ar -s -r -c tmpdir/artest.a tmpdir/unique.o
Executing on host: .../binutils/ar -s -r -c tmpdir/artest.a tmpdir/unique.o (timeout = 300)
.../binutils/ar: tmpdir/unique.o: No such file or directory
FAIL: ar unique symbol in archive
and:
.../gas/testsuite/gas/elf/type.s: Assembler messages:
.../gas/testsuite/gas/elf/type.s:30: Error: symbol type "gnu_unique_object" is supported only by GNU targets
../as-new: BFD (GNU Binutils) 2.26.51.20160628 internal error, aborting at .../gas/write.c:608 in size_seg
../as-new: Please report this bug.
.../gas/testsuite/../../binutils/readelf -s dump.o | grep "1 *\[FIONTCU\]" > dump.out
Executing on host: sh -c {.../gas/testsuite/../../binutils/readelf -s dump.o >readelf.out 2>gas.stderr} /dev/null (timeout = 300)
readelf: Error: dump.o: Failed to read file's magic number
FAIL: elf type list
on MIPS/FreeBSD targets:
mips-freebsd -FAIL: ar unique symbol in archive
mips-freebsd -FAIL: elf type list
mips64-freebsd -FAIL: ar unique symbol in archive
mips64-freebsd -FAIL: elf type list
mips64el-freebsd -FAIL: ar unique symbol in archive
mips64el-freebsd -FAIL: elf type list
mipsel-freebsd -FAIL: ar unique symbol in archive
mipsel-freebsd -FAIL: elf type list
binutils/
* testsuite/binutils-all/ar.exp: Use `supports_gnu_unique' with
the `unique_symbol' test.
gas/
* testsuite/gas/elf/elf.exp: Use `supports_gnu_unique' with the
`type' test.
Some MIPS targets use a named section symbol rather than a symbol with
no name as is used with most ELF targets. When renaming sections, the
named section symbol needs to be renamed too.
Rather than fix this bug, I'd originally intended to just correct the
xfail added recently for update-1.o vs update4.o in update-section.exp,
using the same set of targets for the localize-hidden-1 mips xfail.
I'd extracted that target test into a new function, is_bad_symtab. It
turns out to be useful in readelf.exp too.
bfd/
* config.bfd: Delete mips vxworks patterns matched earlier.
Combine mips*-*-none with mips*-*-elf*.
binutils/
* objcopy.c (find_section_rename): Forward declare. Remove
ibfd and sec_ptr param. Add old_name param. Allow for NULL
returned_flags. Move read of section name and flags to..
(setup_section): ..here. Update find_section_rename call.
(filter_symbols): Rename section symbols for renamed sections.
(copy_object): Call filter_symbols when renamed sections.
* testsuite/lib/binutils-common.exp (is_bad_symtab): New.
* testsuite/binutils-all/update-section.exp: Revert 96037eb0
mips xfail.
* testsuite/binutils-all/objcopy.exp (copy_executable): Use
is_bad_symtab.
(localize-hidden-1): xfail if is_bad_symtab.
* testsuite/binutils-all/readelf.exp: Use is_bad_symtab to select
between mips/tmips.
Showing context lines is confusing in many cases, an obvious example
being loops.
* objdump.c (struct print_file_list): Add "max_printed".
(try_print_file_open): Init new field.
(show_line): Don't show 5 context lines when redisplaying source.
* testsuite/binutils-all/ar.exp: Skip tests for Alpha target.
Skip bfdtest1 tests for tic30 target.
* testsuite/binutils-all/arm/objdump.exp: Skip for aout arm
target.
* testsuite/binutils-all/compress.exp: Expect some tests to fail
on the nds32.
* testsuite/binutils-all/copy-3.d: Skip for go32 targets.
* testsuite/binutils-all/copy-4.d: Skip for AIX and linuxecoff
targets.
* testsuite/binutils-all/nm.exp: Treat beos based targets as ELF
targets.
* testsuite/binutils-all/objcopy.exp: Only run reverse bytes tests
if the bintest.o file was created. Use the
get_standard_section_names proc to get the name of the data
section.
* testsuite/binutils-all/objdump.exp: Update regexps to allow for
RX section names.
* testsuite/binutils-all/readelf.exp: Use
get_standard_section_names proc to get the name of the data
section.
* testsuite/binutils-all/readelf.r: Allow for non standard text
section names.
* testsuite/binutils-all/readelf.s: Update regexps for tilepro.
* testsuite/binutils-all/size.exp: Allow for non standard section
names.
* testsuite/binutils-all/update-section.exp: Expect comapre 1vs4
to fail on mips targets.
* testsuite/lib/utils-lib.exp (default_binutils_run): Use
get_standard_section_names proc.
(run_dump_test): Likewise.
(proc get_standard_section_names): New proc.
binutils* readelf.c (is_24bit_abs_reloc): Add support for R_FT32_20
reloc.
gas * config/tc-ft32.c (md_assemble): Call dwarf2_emit_insn with the
instruction size.
* config/tc-mcore.c (md_assemble): Likewise.
* config/tc-mn10200.c (md_assemble): Likewise.
* config/tc-moxie.c (md_assemble): Likewise.
* config/tc-pj.c (md_apply_fix): Handle BFD_RELOC_PJ_CODE_REL32.
* testsuite/gas/all/gas.exp (diff1 test): Alpha sort list of
exception targets. Add alpha, hppa, microblaze and rl78 to list
of exceptions.
(forward): Add microblaze to list of exceptions.
(fwdexp): Add alpha to list of exceptions.
(redef2): Add arm-epoc-pe and rl78 to list of exceptions.
(redef3): Add rl78 and x86_64 cygwin to list of exceptions.
(do_930509a): Alpha sort list of exception targets. Add h8300 and
mn10200 to list of exceptions.
(align2): Expect to fail for nds32.
(cond): Add alpha and rl78 to list of exceptions.
* testsuite/gas/all/none.d: Skip for ft32 and hppa.
* testsuite/gas/all/string.d: Skip for tic4x.
* testsuite/gas/alpha/alpha.exp: Note that the alpha-linuxecoff
target does not support ELF.
* testsuite/gas/arm/blx-bl-convert.dL Skip for the nto target.
* testsuite/gas/cfi/cfi-alpha-2.d: All extended format names.
* testsuite/gas/cfi/cfi.exp: Alpha sort list of targets. Skip SH
tests for sh-pe and sh-rtemscoff targets.
* testsuite/gas/elf/elf.exp (redef): Add rl78, xgate and vax to
list of exceptions.
(type): Run the noifunc version for alpha-freebsd and visium.
* testsuite/gas/elf/warn-2.s: Do not expect to fail on the mcore,
mn10200 or moxie targets.
* testsuite/gas/ft32/insn.d: Update expected disassembly.
* testsuite/gas/i386/i386.exp (x86-64-pcrel): Skip for cygwin
targets.
* testsuite/gas/lns/lns.exp (lns-common-1): No longer skip for
mcore and rx targets.
* testsuite/gas/macros/macros.exp (dot): Add exceptions for ns32k,
rl78 and vax.
(purge): Expect to fail on the ns32k and vax.
* testsuite/gas/nds32/alu-2.d: Update expected disassembly.
* testsuite/gas/nds32/ls.d: Likewise.
* testsuite/gas/nds32/sys-reg.d: Likewise.
* testsuite/gas/nds32/usr-spe-reg.d: Likewise.
* testsuite/gas/pe/aligncomm-d.d: Skip for the sh.
* testsuite/gas/pe/section-align-3.d: Likewise.
* testsuite/gas/pe/section-exclude.d: Likewise.
* testsuite/gas/ppc/test2xcoff32.d: Pass once all the required
data has been seen.
* testsuite/gas/ppc/textalign-xcoff-001.d: Fix up regexp to allow
for variations in whitespace.
* testsuite/gas/tilepro/t_constants.d: Pass once all the required
data has been seen.
* testsuite/gas/tilepro/t_constants.s (.safe_word): New macro.
Installs a 32-bit value without generating warnings on 64-bit
hosts.
Use the new macro to replace the .word directives.
opcodes * nds32-dis.c (nds32_parse_audio_ext): Change printing of integer
constants to match expected behaviour.
(nds32_parse_opcode): Likewise. Also for whitespace.
Many more places use abfd->my_archive rather than bfd_my_archive (abfd),
so let's make the code consistently use the first idiom.
bfd/
* bfd-in.h (bfd_my_archive): Delete.
* bfd-in2.h: Regenerate.
binutils/
* ar.c: Expand uses of bfd_my_archive.
* size.c: Likewise.
ld/
* ldlang.c: Expand uses of bfd_my_archive.
* ldmain.c: Likewise.
* ldmisc.c: Likewise.
* plugin.c: Likewise.
LTO plugin support in plugin_maybe_claim wants to close the IR bfd
after replacing it with the recompiled object, but can't do so for
archive elements due to various pointers that access the archive bfd.
Thin archives have the same problem. They too cannot have their
element bfds closed.
PR ld/20241
bfd/
* archive.c (open_nested_file): Set my_archive.
* bfd.c (_bfd_default_error_handler <%B>): Exclude archive file name
for thin archives.
* bfdio.c (bfd_tell): Don't adjust origin for thin archives.
(bfd_seek): Likewise.
* bfdwin.c (bfd_get_file_window): Likewise.
* cache.c (cache_bmmap): Likewise.
(bfd_cache_lookup_worker): Don't look in my_archive for thin archives.
* mach-o.c (bfd_mach_o_follow_dsym): Don't open my_archive for
thin archives.
* plugin.c (try_claim): Likewise.
* xcofflink.c (xcoff_link_add_dynamic_symbols): Use import path of
file within thin archive, not the archive.
binutils/
* bucomm.c (bfd_get_archive_filename): Return file name within thin
archive.
ld/
* ldmain.c (add_archive_element): Just print file name of file within
thin archives.
* ldmisc.c (vfinfo): Likewise.
* plugin.c (plugin_object_p): Open file within thin archives.
(plugin_maybe_claim): Expand comment.
Since existing ld and gold support the 64-bit (MIPS) ELF archives, we
can use the 64-bit (MIPS) ELF archives as 64-bit archives. Since the
plugin target is used to create archive in plugin-enabled ar, we need
a way to enable 64-bit archives in the plugin target. This patch adds
--enable-64-bit-archive to bfd to force 64-bit archives in ar and
ranlib. Since both 64-bit MIPS and s390 ELF targets currently use
64-bit archives, 64-bit archives are enabled by default for them.
64-bit archive is generated automatically if the archive is too big.
Tested on Linux/x86 and Linux/x86-64 with existing ld and gold.
bfd/
PR binutils/14625
* archive.c (bfd_slurp_armap): Replace
bfd_elf64_archive_slurp_armap with
_bfd_archive_64_bit_slurp_armap.
(bsd_write_armap): Call _bfd_archive_64_bit_write_armap if
BFD64 is defined and the archive is too big.
(coff_write_armap): Likewise.
* archive64.c (bfd_elf64_archive_slurp_armap): Renamed to ...
(_bfd_archive_64_bit_slurp_armap): This.
(bfd_elf64_archive_write_armap): Renamed to ...
(_bfd_archive_64_bit_write_armap): This.
* configure.ac: Add --enable-64-bit-archive.
(want_64_bit_archive): New. Set to true by default for 64-bit
MIPS and s390 ELF targets.
(USE_64_BIT_ARCHIVE): New AC_DEFINE.
* config.in: Regenerated.
* configure: Likewise.
* elf64-mips.c (bfd_elf64_archive_functions): Removed.
(bfd_elf64_archive_slurp_armap): Likewise.
(bfd_elf64_archive_write_armap): Likewise.
(bfd_elf64_archive_slurp_extended_name_table): Likewise.
(bfd_elf64_archive_construct_extended_name_table): Likewise.
(bfd_elf64_archive_truncate_arname): Likewise.
(bfd_elf64_archive_read_ar_hdr): Likewise.
(bfd_elf64_archive_write_ar_hdr): Likewise.
(bfd_elf64_archive_openr_next_archived_file): Likewise.
(bfd_elf64_archive_get_elt_at_index): Likewise.
(bfd_elf64_archive_generic_stat_arch_elt): Likewise.
(bfd_elf64_archive_update_armap_timestamp): Likewise.
* elf64-s390.c (bfd_elf64_archive_functions): Removed.
(bfd_elf64_archive_slurp_armap): Likewise.
(bfd_elf64_archive_write_armap): Likewise.
(bfd_elf64_archive_slurp_extended_name_table): Likewise.
(bfd_elf64_archive_construct_extended_name_table): Likewise.
(bfd_elf64_archive_truncate_arname): Likewise.
(bfd_elf64_archive_read_ar_hdr): Likewise.
(bfd_elf64_archive_write_ar_hdr): Likewise.
(bfd_elf64_archive_openr_next_archived_file): Likewise.
(bfd_elf64_archive_get_elt_at_index): Likewise.
(bfd_elf64_archive_generic_stat_arch_elt): Likewise.
(bfd_elf64_archive_update_armap_timestamp): Likewise.
* elfxx-target.h (TARGET_BIG_SYM): Use _bfd_archive_64_bit on
BFD_JUMP_TABLE_ARCHIVE if USE_64_BIT_ARCHIVE is defined and
bfd_elfNN_archive_functions isn't defined.
(TARGET_LITTLE_SYM): Likewise.
* libbfd-in.h (_bfd_archive_64_bit_slurp_armap): New prototype.
(_bfd_archive_64_bit_write_armap): Likewise.
(_bfd_archive_64_bit_slurp_extended_name_table): New macro.
(_bfd_archive_64_bit_construct_extended_name_table): Likewise.
(_bfd_archive_64_bit_truncate_arname): Likewise.
(_bfd_archive_64_bit_read_ar_hdr): Likewise.
(_bfd_archive_64_bit_write_ar_hdr): Likewise.
(_bfd_archive_64_bit_openr_next_archived_file): Likewise.
(_bfd_archive_64_bit_get_elt_at_index): Likewise.
(_bfd_archive_64_bit_generic_stat_arch_elt): Likewise.
(_bfd_archive_64_bit_update_armap_timestamp): Likewise.
* libbfd.h: Regenerated.
* plugin.c (plugin_vec): Use _bfd_archive_64_bit on
BFD_JUMP_TABLE_ARCHIVE if USE_64_BIT_ARCHIVE is defined.
binutils/
PR binutils/14625
* NEWS: Mention --enable-64-bit-archive.
Mixing MIPS16 and microMIPS code in a single binary isn't usually
supported but GAS happily produces such code if requested. However it
is not correctly disassembled even if a symbol table is available and
function symbols are correctly anotated with the ISA mode. This is
because the ELF-header global microMIPS ASE flag takes precedence over
MIPS16 function annotation, causing them to be treated as regular MIPS
code.
Correct the problem by respecting function symbol anotation regardless
of the ELF-header flag.
binutils/
* testsuite/binutils-all/mips/mixed-mips16-micromips.d: New test.
* testsuite/binutils-all/mips/mixed-mips16-micromips.s: New test
source.
* testsuite/binutils-all/mips/mips.exp: Run the new test.
opcodes/
* mips-dis.c (is_compressed_mode_p): Add `micromips_p' operand,
replacing references to `micromips_ase' throughout.
(_print_insn_mips): Don't use file-level microMIPS annotation to
determine the disassembly mode with the symbol table.
binutils/
* readelf.c (dynamic_section_mips_val) <DT_MIPS_RLD_VERSION>
<DT_MIPS_LOCAL_GOTNO, DT_MIPS_CONFLICTNO, DT_MIPS_LIBLISTNO>
<DT_MIPS_SYMTABNO, DT_MIPS_UNREFEXTNO, DT_MIPS_HIPAGENO>
<DT_MIPS_DELTA_CLASS_NO, DT_MIPS_DELTA_INSTANCE_NO>
<DT_MIPS_DELTA_RELOC_NO, DT_MIPS_DELTA_SYM_NO>
<DT_MIPS_DELTA_CLASSSYM_NO, DT_MIPS_COMPACT_SIZE>: Use the
`d_val' rather than `d_ptr' member of the dynamic entry.
Correct a regression introduced with commit 685080f210 ("Adds support
for generating notes in V850 binaries.") which replaced rather than
extending the call to `_bfd_elf_copy_private_bfd_data' with
`v850_elf_copy_private_bfd_data'. Consequently ELFOSABI_GNU marking is
not propagated to output by `objcopy' from objects containing
STB_GNU_UNIQUE symbols.
bfd/
* elf32-v850.c (v850_elf_copy_notes): New function, factored out
from...
(v850_elf_copy_private_bfd_data): ... here. Call the new
function and `_bfd_elf_copy_private_bfd_data'.
binutils/
* testsuite/binutils-all/objcopy.exp: Don't skip the `strip-10'
test for the V850.
The documentation for 'nm --size-sort' is out of step with the code, the
special handling for ELF is not mentioned in the documentation, and
could cause confusion to a user.
binutils/ChangeLog:
* doc/binutils.texi (nm): Update description of --size-sort.
PR binutils/20063
* elf.c (bfd_elf_get_elf_syms): Check for out of range sh_link
field before accessing sections array.
* readelf.c (get_32bit_section_headers): Warn if an out of range
sh_link or sh_info field is encountered.
(get_64bit_section_headers): Likewise.
binutils* testsuite/lib/binutils-common.exp (is_elf_format): Add avr-*-*.
ld * testsuite/ld-elf/pr18735.d: Allow other symbols.
* testsuite/ld-elf/sec64k.exp: Skip 64ksec for avr.
* testsuite/ld-gc/pr14265.d: Allow other symbols.
* testsuite/ld-plugin/plugin.exp: Add PR ld/17973 to
plugin_tests only if check_shared_lib_support is true.
* testsuite/ld-selective/selective.exp: Add --section-start
flag for avr.
* readelf.c (is_32bit_pcrel_reloc): Return true if reloc is 32-bit
PC relocation for AVR target.
(is_none_reloc): Return true if reloc is any of AVR diff
relocations.
PR 19938
bfd * elf-bfd.h (struct elf_backend_data): Rename
elf_backend_set_special_section_info_and_link to
elf_backend_copy_special_section_fields.
* elfxx-target.h: Likewise.
* elf.c (section_match): Ignore the SHF_INFO_LINK flag when
comparing section flags.
(copy_special_section_fields): New function.
(_bfd_elf_copy_private_bfd_data): Copy the EI_ABIVERSION field.
Perform two scans over special sections. The first one looks for
a direct mapping between the output section and an input section.
The second scan looks for a possible match based upon section
characteristics.
* elf32-arm.c (elf32_arm_copy_special_section_fields): New
function. Handle setting the sh_link field of SHT_ARM_EXIDX
sections.
* elf32-i386.c (elf32_i386_set_special_info_link): Rename to
elf32_i386_copy_solaris_special_section_fields.
* elf32-sparc.c (elf32_sparc_set_special_section_info_link):
Rename to elf32_sparc_copy_solaris_special_section_fields.
* elf64-x86-64.c (elf64_x86_64_set_special_info_link): Rename to
elf64_x86_64_copy_solaris_special_section_fields.
binutils* readelf.c (get_solaris_segment_type): New function.
(get_segment_type): Call it.
PR target/19722
opcodes * aarch64-dis.c (aarch64_opcode_decode): Run verifier if present.
* aarch64-opc.c (verify_ldpsw): New function.
* aarch64-opc.h (verify_ldpsw): New prototype.
* aarch64-tbl.h: Add initialiser for verifier field.
(LDPSW): Set verifier to verify_ldpsw.
binutils* testsuite/binutils-all/aarch64/illegal.s: New test.
* testsuite/binutils-all/aarch64/illegal.d: New test driver.
include * opcode/aarch64.h (struct aarch64_opcode): Add verifier field.
PR target/19938
bfd * elf-bbfd.h (struct elf_backend_data): New field:
elf_strtab_flags.
New field: elf_backend_set_special_section_info_and_link
* elfxx-target.h (elf_backend_strtab_flags): Define if not already
defined.
(elf_backend_set_special_section_info_and_link): Define if not
already defined.
(elfNN_bed): Use elf_backend_set_special_section_info_and_link and
elf_backend_strtab_flags macros to initialise fields in structure.
* elf.c (_bfd_elf_make_section_from_shdr): Check for SHF_STRINGS
being set even if SHF_MERGE is not set.
(elf_fake_sections): Likewise.
(section_match): New function. Matches two ELF sections based
upon fixed characteristics.
(find_link): New function. Locates a section in a BFD that
matches a section in a different BFD.
(_bfd_elf_copy_private_bfd_data): Copy the sh_info and sh_link
fields of reserved sections.
(bfd_elf_compute_section_file_positions): Set the flags for the
.shstrtab section based upon the elf_strtab_flags field in the
elf_backend_data structure.
(swap_out_syms): Likewise for the .strtab section.
* elflink.c (bfd_elf_final_link): Set the flags for the
.strtab section based upon the elf_strtab_flags field in the
elf_backend_data structure.
* elf32-i386.c (elf32_i386_set_special_info_link): New function.
(elf_backend_strtab_flags): Set to SHF_STRINGS for Solaris
targets.
(elf_backend_set_special_section_info_and_link): Define for
Solaris targets.
* elf32-sparc.c: Likewise.
* elf64-x86-64.c: Likewise.
binutils* testsuite/binutils-all/i386/compressed-1b.d: Allow for the
string sections possibly having the SHF_STRINGS flag bit set.
* testsuite/binutils-all/i386/compressed-1c.d: Likewise.
* testsuite/binutils-all/readelf.s: Likewise.
* testsuite/binutils-all/readelf.s-64: Likewise.
* testsuite/binutils-all/x86-64/compressed-1b.d: Likewise.
* testsuite/binutils-all/x86-64/compressed-1c.d: Likewise.
gas * testsuite/gas/i386/ilp32/x86-64-unwind.d: Allow for the string
sections possibly having the SHF_STRINGS flag bit set.
* testsuite/gas/i386/x86-64-unwind.d: Likewise.
PR target/19983
* readelf.c (get_solaris_section_type): New function: Returns the
name of Solaris specific section types.
(get_solaris_dynamic_type): New function: Return the name of
Solaris specific dynamic types.
(get_dynamic_type): Use get_solaris_dynamic_type.
(get_section_type_name): Use get_solaris_section_type.
(get_solaris_symbol_visibility): New function: Returns Solaris
specific symbol visibilities.
(print_dynamic_symbol): Use get_solaris_symbol_visibility.
(process_symbol_table): Likewise.
PR 19872
bfd * dwarf2.c (parse_comp_unit): Skip warning about unrecognised
version number if the version is zero.
bin * dwarf.c (display_debug_aranges): Skip warning about unrecognised
version number if the version is zero.
bfd * warning.m4 (GCC_WARN_CFLAGS): Only add -Wstack-usage if using a
sufficiently recent version of GCC.
* configure: Regenerate.
others * configure: Regenerate.
This commit introduces the nps400 machine type as a variant of arc.
There's a new flag in the assembler to select this machine type. All
other changes are just adding handling of the new machine type into the
relevant places.
The nps400 is an arc700 variant with some vendor specific instructions
added into the instruction set. This commit does not add any of the new
instructions, this is just laying the groundwork for future commits.
However, in preparation for these new instructions a new opcode define for
nps400 has been added to include/opcode/arc.h, this new opcode define is
used in the assembler and disassembler along with the existing define
for arc700 such that when assembling and disassembling for nps400 the
user will have access to all arc700 instructions and all the nps400
vendor extension instructions.
bfd/ChangeLog:
* archures.c (bfd_mach_arc_nps400): Define.
* bfd-in2.h: Regenerate.
* cpu-arc.c (arch_info_struct): New entry for nps400, renumber
some existing entries to make space.
* elf32-arc.c (arc_elf_object_p): Add nps400 case.
(arc_elf_final_write_processing): Likewise.
binutils/ChangeLog:
* readelf.c (decode_ARC_machine_flags): Handle nps400.
gas/ChangeLog:
* config/tc-arc.c (cpu_types): Add nps400 entry.
(check_zol): Handle nps400.
include/ChangeLog:
* elf/arc.h (E_ARC_MACH_NPS400): Define.
* opcode/arc.h (ARC_OPCODE_NPS400): Define.
opcodes/ChangeLog:
* arc-dis.c (print_insn_arc): Handle nps400.
The constant EF_ARC_CPU_GENERIC is defined in the include/elf/arc.h
file, and is used in a few places in binutils, however, this constant
should never make it into the elf header flags; we always set a valid
cpu type in the assembler, which should then be copied over during
linking.
There are some non-gnu arc compilers that don't write an architecture
type into the e_flags field, instead leaving the field as 0, which is
the EF_ARC_CPU_GENERIC value. This non-gnu compiler uses the machine
type to distinguish between the old and newer arc architectures, setting
the machine type to EM_ARC_COMPACT for old arc600, arc601, and arc700
architectures, while using EM_ARC_COMPACT2 for newer arcem and archs
architectures.
Previously when displaying the machine flags for an older EM_ARC_COMPACT
machine, if the e_flags had not been filled in, then we relied on the
default case statement to display the message "Generic ARCompact", while
in the EM_ARC_COMPACT2 case we specifically handled EF_ARC_CPU_GENERIC
to print "ARC Generic", leaving the default case to print a message
about unrecognised cpu flag.
After this commit EF_ARC_CPU_GENERIC has been removed, for both machine
types EM_ARC_COMPACT and EM_ARC_COMPACT2 we now rely on the default case
statement to handle the situation where the e_flags has not been filled
in. The message displayed is now "Unknown ARCompact" (for older arc
architectures) and "Unknown ARC" (for the newer architectures). The
switch from "Generic" to "Unknown" in the message string is for clarity,
calling the file "Generic" can give the impression that the file is
compiled for a common sub-set of the architectures, and would therefore
run on any type of machine (or at least any type of new or old machine
depending on if the machine type is ARC or ARCv2). However, this was
not what "Generic" meant, it really meant "Unknown", so that's what we
now say.
As part of the merging of the readelf flag reading code, I have unified
the strings used in displaying the ELF ABI. This means that for older
arc machines (arc600, arc601, and arc700) the string used for the
original ABI, and ABIv2 have changed, the current ABIv3 remains the
same. For the newer architectures (arcem and archs) the abi strings
remain unchanged in all cases.
bfd/ChangeLog:
* elf32-arc.c (arc_elf_print_private_bfd_data): Remove use of
EF_ARC_CPU_GENERIC.
(arc_elf_final_write_processing): Don't bother setting cpu field
in e_flags, this will have been set elsewhere.
binutils/ChangeLog:
* readelf.c (get_machine_flags): Move arc processing into...
(decode_ARC_machine_flags): ... new function. Remove use of
EF_ARC_CPU_GENERIC, change default case from "generic arc" to
"unknown arc". Merged ABI printing between two machine types.
gas/ChangeLog:
* config/tc-arc.c (arc_select_cpu): Remove use of
EF_ARC_CPU_GENERIC.
include/ChangeLog:
* elf/arc.h (EF_ARC_CPU_GENERIC): Delete. Update related comment.
This commit restructures the selection of the default cpu/mach so that
the choice is made from md_begin (if the user has not provided a command
line choice). This will reduce the amount of change needed in a later
patch.
At the request of Synopsys, the default architecture changes to ARC700
from this commit, previously the default was a non-existent
super-architecture that contained all instructions from all arc
variants. There's some clean up associated with removing the default
merged architecture, and a small test fix now that the default is
ARC700.
binutils/ChangeLog:
* testsuite/binutils-all/objdump.exp (cpus_expected): Add ARC700
to the architecture list.
gas/ChangeLog:
* config/tc-arc.c (arc_target): Delay initialisation until
arc_select_cpu.
(arc_target_name): Likewise.
(arc_features): Likewise.
(arc_mach_type): Likewise.
(cpu_types): Remove "all" entry.
(arc_select_cpu): New function, most of the content is from...
(md_parse_option): ... here. Call new arc_select_cpu.
(md_begin): Call arc_select_cpu if needed, default is now arc700.
include/ChangeLog:
* opcode/arc.h (ARC_OPCODE_BASE): Delete.
opcodes/ChangeLog:
* arc-opc.c (BASE): Delete.
bfd PR binutils/19775
* archive.c (bfd_generic_openr_next_archived_file): Allow zero
length elements in the archive.
binutils PR binutils/19775
* testsuite/binutils-all/ar.exp (proc empty_archive): New proc.
Run the new proc.
* testsuite/binutils-all/empty: New, empty, file.
gas * doc/as.texinfo (.section): Document that numeric values can now
be used for the flags and type fields of the ELF target's .section
directive. Add notes about the restrictions on setting flags and
types.
* config/obj-elf.c (obj_elf_change_section): Allow known sections
to be given processor specific section types. Allow processor and
application specific flags of a section to be set after
definition.
(obj_elf_parse_section_letters): Handle parsing numeric values.
(obj_elf_section_type): Handle parsing numeric values.
(obj_elf_section): Allow numeric type values.
* config/obj-elf.h (obj_elf_change_section): Update prototype.
* testsuite/gas/elf/section10.d: New test.
* testsuite/gas/elf/section10.s: Source file for new test.
* testsuite/gas/elf/elf.exp: Run the new test.
* testsuite/gas/i386/ilp32/x86-64-unwind.d: Remove dependency upon
the description of the flags produced by readelf.
* testsuite/gas/tic6x/scomm-directive-4.d: Likewise.
* NEWS: Mention the new feature.
bfd * elf-bfd.h (struct bfd_elf_special_section): Use unsigned values
for length and type fields. Use a signed value for the
suffix_length field.
binutils* readelf.c (get_section_type_name): Add hex prefix to offsets
printed for LOPROC and LOOS values. Ensure that a result is
always returned for the V850 target, even when an unrecognised
processor specific value is encountered.
(process_section_headers): Display key values in the order in
which they appear to the user. Add the "C (compressed)" value to
the list.
ld * testsuite/ld-i386/pr12718.d: Remove dependency upon the
description of the flags produced by readelf.
* testsuite/ld-i386/pr12921.d: Likewise.
* testsuite/ld-i386/tlsbin-nacl.rd: Likewise.
* testsuite/ld-i386/tlsbin.rd: Likewise.
* testsuite/ld-i386/tlsbindesc-nacl.rd: Likewise.
* testsuite/ld-i386/tlsbindesc.rd: Likewise.
* testsuite/ld-i386/tlsdesc-nacl.rd: Likewise.
* testsuite/ld-i386/tlsdesc.rd: Likewise.
* testsuite/ld-i386/tlsgdesc-nacl.rd: Likewise.
* testsuite/ld-i386/tlsgdesc.rd: Likewise.
* testsuite/ld-i386/tlsnopic-nacl.rd: Likewise.
* testsuite/ld-i386/tlsnopic.rd: Likewise.
* testsuite/ld-i386/tlspic-nacl.rd: Likewise.
* testsuite/ld-i386/tlspic.rd: Likewise.
* testsuite/ld-s390/tlsbin.rd: Likewise.
* testsuite/ld-s390/tlsbin_64.rd: Likewise.
* testsuite/ld-s390/tlspic.rd: Likewise.
* testsuite/ld-s390/tlspic_64.rd: Likewise.
* testsuite/ld-sh/tlsbin-2.d: Likewise.
* testsuite/ld-sh/tlspic-2.d: Likewise.
* testsuite/ld-tic6x/common.d: Likewise.
* testsuite/ld-tic6x/shlib-1.rd: Likewise.
* testsuite/ld-tic6x/shlib-1b.rd: Likewise.
* testsuite/ld-tic6x/shlib-1r.rd: Likewise.
* testsuite/ld-tic6x/shlib-1rb.rd: Likewise.
* testsuite/ld-tic6x/shlib-app-1.rd: Likewise.
* testsuite/ld-tic6x/shlib-app-1b.rd: Likewise.
* testsuite/ld-tic6x/shlib-app-1r.rd: Likewise.
* testsuite/ld-tic6x/shlib-app-1rb.rd: Likewise.
* testsuite/ld-tic6x/shlib-noindex.rd: Likewise.
* testsuite/ld-tic6x/static-app-1.rd: Likewise.
* testsuite/ld-tic6x/static-app-1b.rd: Likewise.
* testsuite/ld-tic6x/static-app-1r.rd: Likewise.
* testsuite/ld-tic6x/static-app-1rb.rd: Likewise.
* testsuite/ld-x86-64/ilp32-4-nacl.d: Likewise.
* testsuite/ld-x86-64/ilp32-4.d: Likewise.
* testsuite/ld-x86-64/pr12718.d: Likewise.
* testsuite/ld-x86-64/pr12921.d: Likewise.
* testsuite/ld-x86-64/split-by-file-nacl.rd: Likewise.
* testsuite/ld-x86-64/split-by-file.rd: Likewise.
* testsuite/ld-x86-64/tlsbin-nacl.rd: Likewise.
* testsuite/ld-x86-64/tlsbin.rd: Likewise.
* testsuite/ld-x86-64/tlsbindesc-nacl.rd: Likewise.
* testsuite/ld-x86-64/tlsbindesc.rd: Likewise.
* testsuite/ld-x86-64/tlsdesc-nacl.rd: Likewise.
* testsuite/ld-x86-64/tlsdesc.rd: Likewise.
* testsuite/ld-x86-64/tlsgdesc-nacl.rd: Likewise.
* testsuite/ld-x86-64/tlsgdesc.rd: Likewise.
* testsuite/ld-x86-64/tlspic-nacl.rd: Likewise.
* testsuite/ld-x86-64/tlspic.rd: Likewise.
* testsuite/ld-xtensa/tlsbin.rd: Likewise.
* testsuite/ld-xtensa/tlspic.rd: Likewise.
For objcopy, --compress-debug-sections=none is the same as
--decompress-debug-sections, not --nocompress-debug-sections.
* doc/binutils.texi: Fix a typo.
The HAS_RELOC bit should be cleared when relocations are removed from
relocatable files.
bfd/
PR binutils/19547
* elf.c (assign_section_numbers): Clear HAS_RELOC if there are
no relocations in relocatable files.
binutils/
PR binutils/19547
* testsuite/binutils-all/objcopy.exp
(objcopy_test_without_global_symbol): New proc.
Run objcopy_test_without_global_symbol.
* testsuite/binutils-all/pr19547.c: New file.
We should set BFD_DECOMPRESS to decompress debug sections when reading in
DWARF debug sections.
bfd/
PR binutils/19523
* dwarf2.c (_bfd_dwarf2_slurp_debug_info): Set BFD_DECOMPRESS to
decompress debug sections.
binutils/
PR binutils/19523
* Makefile.am (check-DEJAGNU): Pass CC and CC_FOR_BUILD to
runtest.
* Makefile.in: Regenerated.
* testsuite/binutils-all/compress.exp (test_gnu_debuglink): New
proc.
Run test_gnu_debuglink for native ELF build.
bfd/ChangeLog:
* elf32-arm.c ((elf32_arm_special_sections): Remove catch of noread
section using '.text.noread' pattern.
gas/ChangeLog:
* config/obj-elf.c (obj_elf_change_section) : Allow arm section with
SHF_ARM_NOREAD section flag.
* config/tc-arm.h (md_elf_section_letter) : Implement this hook to
handle letter 'y'.
(arm_elf_section_letter) : Declare it.
* config/tc-arm.c (arm_elf_section_letter): Handle letter 'y' to set
SHF_ARM_NOREAD section flag.
* doc/c-arm.texi (ARM section attribute 'y'): Document it.
gas/testsuite/ChangeLog:
* gas/arm/section-execute-only.s: New test case.
* gas/arm/section-execute-only.d: Expected output.
ld/testsuite/ChangeLog:
* ld-arm/thumb1-noread-not-present-mixing-two-section.s: Add 'y'
attribute usage.
* ld-arm/thumb1-noread-present-one-section.s: Likewise.
* ld-arm/thumb1-noread-present-two-section.s: Likewise.
* ld-arm/thumb1-input-section-flag-match.s: Likewise.
binutils/ChangeLog:
* readelf.c (get_elf_section_flags): Display y letter for section
with SHF_ARM_NOREAD section flag in readelf section output.
(process_section_headers): Add y letter in readelf section output
key mapping for ARM architecture.
bfd/ChangeLog:
* arc-plt.def: New file.
* arc-plt.h: Likewise.
* elf32-arc.c (elf_arc_abs_plt0_entry, elf_arc_abs_pltn_entry,
elf_arcV2_abs_plt0_entry, elf_arcV2_abs_pltn_entry,
elf_arc_pic_plt0_entry, elf_arc_pic_pltn_entry,
elf_arcV2_pic_plt0_entry, elf_arcV2_pic_pltn_entry): Remove.
(name_for_global_symbol): Added.
(ADD_RELA): Helper to create dynamic relocs.
(new_got_entry_to_list): Create a new got entry in linked list.
(symbol_has_entry_of_type): Search for specific type of entry in
list.
(is_reloc_for_GOT): return FALSE for any TLS related relocs.
(is_reloc_for_TLS, arc_elf_set_private_flags)
(arc_elf_print_private_bfd_data, arc_elf_copy_private_bfd_data)
(arc_elf_merge_private_bfd_data): New functions.
(debug_arc_reloc): Cleaned debug info printing.
(PDATA reloc): Changed not to perform address alignment.
(reverse_me): Added. Fix for ARC_32 relocs.
(arc_do_relocation): Return bfd_reloc_of when no relocation should
occur.
(arc_get_local_got_ents): Renamed from arc_get_local_got_offsets.
Changed function to access an array of list of GOT entries instead
of just an array of offsets.
(elf_arc_relocate_section): Added support for PIC and TLS related relocations.
(elf_arc_check_relocs): Likewise.
(elf_arc_adjust_dynamic_symbol, elf_arc_finish_dynamic_symbol,
(elf_arc_finish_dynamic_sections): Likewise
(arc_create_dynamic_sections): Modified conditions to create
dynamic sections.
(ADD_SYMBOL_REF_SEC_AND_RELOC): New macro.
(plt_do_relocs_for_symbol, relocate_plt_for_symbol)
(relocate_plt_for_entry): Changed to support new way to define PLT
related code.
(add_symbol_to_plt): Likewise.
(arc_elf_link_hash_table_create): New function.
include/ChangeLog:
* elf/arc-reloc.def (ARC_32, ARC_GOTPC, ARC_TLS_GD_GOT)
(ARC_TLS_IE_GOT, ARC_TLS_DTPOFF, ARC_TLS_DTPOFF_S9, ARC_TLS_LE_S9)
(ARC_TLS_LE_32): Fixed formula.
(ARC_TLS_GD_LD): Use new special function.
* opcode/arc-func.h: Changed all the replacement
functions to clear the patching bits before doing an or it with the value
argument.
Oddly, config.sub converts a duple ending in -elf for these target to
-unknown-none, which means they aren't seen as elf targets by
binutils. So, counter that. This exposes a number of testsuite
issues (ones you would have seen if configuring with a full triple,
say m68hc11-unknown-elf).
binutils/
* testsuite/lib/binutils-common.exp (is_elf_format): Return true
for m68hc11/12 and xgate triples.
gas/
* testsuite/gas/cfi/cfi.exp: Exclude m68hc11/12 from m68k test.
ld/
* testsuite/lib/ld-lib.exp (check_shared_lib_support): Exclude xgate.
* testsuite/ld-elf/endsym.d: xfail m68hc11/12 and xgate.
* testsuite/ld-elf/pr14156a.d: Likewise.
* testsuite/ld-elf/pr14926.d: Don't run for m68hc11/12 and xgate.
* testsuite/ld-elf/sec64k.exp: Likewise.
2015-12-24 Thomas Preud'homme <thomas.preudhomme@arm.com>
bfd/
(tag_cpu_arch_combine): Adjust comment in v4t_plus_v6_m with regards
to merging with ARMv8-M Baseline.
binutils/
* readelf.c (arm_attr_tag_CPU_arch): Add ARMv8-M Baseline Tag_CPU_arch
value.
gas/
* config/tc-arm.c (arm_ext_v6t2_v8m): New feature for instructions
shared between ARMv6T2 and ARMv8-M.
(move_or_literal_pool): Check mov.w/mvn and movw availability against
arm_ext_v6t2 and arm_ext_v6t2_v8m respectively instead of checking
arm_arch_t2.
(do_t_branch): Error out for wide conditional branch instructions if
targetting ARMv8-M Baseline.
(non_v6t2_wide_only_insn): Add the logic for new wide-only instructions
in ARMv8-M Baseline.
(wide_insn_ok): New function.
(md_assemble): Use wide_insn_ok instead of non_v6t2_wide_only_insn and
adapt error message for unsupported wide instruction to ARMv8-M
Baseline.
(insns): Reorganize instructions shared by ARMv8-M Baseline and
ARMv6t2 architecture.
(arm_cpus): Set feature bit ARM_EXT2_V6T2_V8M for marvell-pj4 and
marvell-whitney cores.
(arm_archs): Define armv8-m.base architecture.
(cpu_arch_ver): Define ARM_ARCH_V8M_BASE architecture version.
(aeabi_set_public_attributes): Add logic to set Tag_CPU_arch to 17 for
ARMv8-M Mainline. Set Tag_DIV_use for ARMv8-M Baseline as well.
gas/testsuite/
* gas/arm/archv8m-base.d: New file.
* gas/arm/attr-march-armv8m.base.d: Likewise.
* gas/arm/armv8m.base-idiv.d: Likewise.
* gas/arm/any-armv8m.d: Adapt to deal with ARMv8-M Baseline.
include/elf/
* arm.h (TAG_CPU_ARCH_V8M_BASE): Declare.
include/opcode/
* arm.h (ARM_EXT2_V6T2_V8M): New extension bit.
(ARM_AEXT2_V8A): New architecture extension bitfield.
(ARM_AEXT2_V8_1A): Use ARM_AEXT2_V8A instead of ARM_EXT2_ATOMICS.
(ARM_AEXT_V8M_BASE): New architecture extension bitfield.
(ARM_AEXT2_V8M): Add extension bit ARM_EXT2_V6T2_V8M.
(ARM_ARCH_V6T2): Use ARM_EXT2_V6T2_V8M for the second extension
bitfield.
(ARM_ARCH_V6KT2): Likewise.
(ARM_ARCH_V6ZT2): Likewise.
(ARM_ARCH_V6KZT2): Likewise.
(ARM_ARCH_V7): Likewise.
(ARM_ARCH_V7A): Likewise.
(ARM_ARCH_V7VE): Likewise.
(ARM_ARCH_V7R): Likewise.
(ARM_ARCH_V7M): Likewise.
(ARM_ARCH_V7EM): Likewise.
(ARM_ARCH_V8A): Likewise.
(ARM_ARCH_V8M_BASE): New architecture bitfield.
(ARM_ARCH_THUMB2): Include instructions shared by ARMv6t2 and ARMv8-M.
(ARM_ARCH_V7A_SEC): Use ARM_EXT2_V6T2_V8M for the second extension
bitfield and reindent.
(ARM_ARCH_V7A_MP_SEC): Likewise.
(ARM_ARCH_V7R_IDIV): Likewise.
(ARM_ARCH_V8A_FP): Use ARM_AEXT2_V8A instead of ARM_EXT2_ATOMICS.
(ARM_ARCH_V8A_SIMD): Likewise.
(ARM_ARCH_V8A_CRYPTOV1): Likewise.
opcodes/
* arm-dis.c (arm_opcodes): Guard movw, movt cbz, cbnz, clrex, ldrex,
ldrexb, ldrexh, strex, strexb, strexh shared by ARMv6T2 and ARMv8-M by
ARM_EXT2_V6T2_V8M instead of ARM_EXT_V6T2.
2015-12-24 Thomas Preud'homme <thomas.preudhomme@arm.com>
bfd/
(tag_cpu_arch_combine): Adjust v4t_plus_v6_m and comb array to account
for new TAG_CPU_ARCH_V4T_PLUS_V6_M value. Deal with NULL values in
comb array.
binutils/
* readelf.c (arm_attr_tag_CPU_arch): Add ARMv8-M Mainline Tag_CPU_arch
value.
(arm_attr_tag_THUMB_ISA_use): Add ARMv8-M Mainline Tag_THUMB_ISA_use
value.
gas/
* config/tc-arm.c (arm_ext_m): Include ARMv8-M.
(arm_ext_v8m): New feature for ARMv8-M.
(arm_ext_atomics): New feature for ARMv8 atomics.
(do_tt): New encoding function for TT* instructions.
(insns): Add new entries for ARMv8-M specific instructions and
reorganize the ones shared by ARMv8-M Mainline and ARMv8-A.
(arm_archs): Define armv8-m.main architecture.
(cpu_arch_ver): Define ARM_ARCH_V8M_MAIN architecture version and
clarify the ordering rule.
(aeabi_set_public_attributes): Use TAG_CPU_ARCH_* macro to refer to
Tag_CPU_arch values for ARMv7e-M detection. Add logic to keep setting
Tag_CPU_arch to ARMv8-A for -march=all. Also set Tag_CPU_arch_profile
to 'A' if extension bit for atomic instructions is set, unless it is
ARMv8-M. Set Tag_THUMB_ISA_use to 3 for ARMv8-M. Set Tag_DIV_use to 0
for ARMv8-M Mainline.
gas/testsuite/
* gas/arm/archv8m.s: New file.
* gas/arm/archv8m-main.d: Likewise.
* gas/arm/attr-march-armv8m.main.d: Likewise.
* gas/arm/any-armv8m.s: Likewise.
* gas/arm/any-armv8m.d: Likewise.
include/elf/
* arm.h (TAG_CPU_ARCH_V8M_MAIN): Declare.
(MAX_TAG_CPU_ARCH): Define to TAG_CPU_ARCH_V8M_MAIN.
(TAG_CPU_ARCH_V4T_PLUS_V6_M): Define to unused value 15.
include/opcode/
* arm.h (ARM_EXT2_ATOMICS): New extension bit.
(ARM_EXT2_V8M): Likewise.
(ARM_EXT_V8): Adjust comment with regards to atomics and remove
mention of legacy use for that bit.
(ARM_AEXT2_V8_1A): New architecture extension bitfield.
(ARM_AEXT2_V8_2A): Likewise.
(ARM_AEXT_V8M_MAIN): Likewise.
(ARM_AEXT2_V8M): Likewise.
(ARM_ARCH_V8A): Use ARM_EXT2_ATOMICS for features in second bitfield.
(ARM_ARCH_V8_1A): Likewise with ARM_AEXT2_V8_1A.
(ARM_ARCH_V8_2A): Likewise with ARM_AEXT2_V8_2A.
(ARM_ARCH_V8M_MAIN): New architecture feature bitfield.
(ARM_ARCH_V8A_FP): Use ARM_EXT2_ATOMICS for features in second bitfield
and reindent.
(ARM_ARCH_V8A_SIMD): Likewise.
(ARM_ARCH_V8A_CRYPTOV1): Likewise.
(ARM_ARCH_V8_1A_FP): Use ARM_AEXT2_V8_1A to set second bitfield of
feature bits.
(ARM_ARCH_V8_1A_SIMD): Likewise.
(ARM_ARCH_V8_1A_CRYPTOV1): Likewise.
opcodes/
* arm-dis.c (arm_opcodes): Guard lda, ldab, ldaex, ldaexb, ldaexh, stl,
stlb, stlh, stlex, stlexb and stlexh by ARM_EXT2_ATOMICS instead of
ARM_EXT_V8.
(thumb32_opcodes): Add entries for wide ARMv8-M instructions.
include/elf
* arm.h: Add arm SHF_ARM_NOREAD section flag.
bfd * bfd-in2.h: Regenerate.
* section.c: Add SEC_ELF_NOREAD.
* elf32-arm.c (elf32_arm_post_process_headers): Only set
PF_X attribute if a segment only contains section with
SHF_ARM_NOREAD flag.
(elf32_arm_fake_sections): Add SEC_ELF_NOREAD conversion.
(elf32_arm_section_flags): New function to convert SHF_ARM_NOREAD
to bfd flag.
(elf32_arm_lookup_section_flags): New function to allow
INPUT_SECTION_FLAGS directive with SHF_ARM_NOREAD flag.
(elf32_arm_special_sections): Add special sections array
to catch section prefix by '.text.noread' pattern.
ld/testsuite
* ld-arm/arm-elf.exp: New tests.
* ld-arm/thumb1-input-section-flag-match.d: New
* ld-arm/thumb1-input-section-flag-match.s: New
* ld-arm/thumb1-noread-not-present-mixing-two-section.d: New
* ld-arm/thumb1-noread-not-present-mixing-two-section.s: New
* ld-arm/thumb1-noread-present-one-section.d: New
* ld-arm/thumb1-noread-present-one-section.s: New
* ld-arm/thumb1-noread-present-two-section.d: New
* ld-arm/thumb1-noread-present-two-section.s: New
binutils
* readelf.c (get_elf_section_flags): Add support for ARM specific
section flags.
Maciej W. Rozycki
Andrew Waterman
Jiong Wang
Nick Clifton
Etienne Buira
Jose E. Marchesi
Luis Machado
Claudiu Zissulescu
Ambrogino Modigliani
Alan Modra
Mark Wielaard
Rudy
Andrew Burgess
Tom Tromey
Palmer Dabbelt
Andreas Krebbel
Vlad Zakharov
Ed Maste
H.J. Lu
Andre Vieria
Tristan Gingold
Graham Markall
John Baldwin
Matthew Fortune
Thomas Preud'homme
Senthil Kumar Selvaraj
Pitchumani Sivanupandi
Trevor Saunders
Andreas Arnez
Matthew Wahab
Cupertino Miranda
Mickael Guene
Yoshinori Sato
Jan Beulich