Fix legacy interrupt mode for NX3031 chips, read pci interrupt state
in hardware to guard against spurious interrupt.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add couple of new board configurations based on NX3031 chip.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
For NX3031, the phy is managed by firmware, so driver should avoid
setting any phy registers.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The commit that made the CONFIG_GFAR_NAPI code unconditional was
included at the same time as a new CONFIG_GFAR_NAPI user, resulting
in these bugus #ifdef's.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Currently when we do a packet flood to the Ethernet port, the console
reports error every time when a packet is dropped. This is too
redundant and cost performance. Remove message for this type of event.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds support for limiting the number of tx pause frames to a
default of 8. Previously, hardware would send out continuous stream of
pause frames.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds jumbo frame support for MCP79 chipsets.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds support for new tx statistic counters in the hardware -
unicast, multicast, and broadcast
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch enforces a stricter policy on rx errors. The driver needs to
verify whether there are multiple rx errors versus a single error.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix the problems reported for 2.6.27-rc1 caused by over aggressive
power management. Turning clock off on PCI Express is problematic for WOL,
and when doing multi-booting.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
igb_init_managability does not actually perform any function as the two
registers it attempts to write are both read only on the host. This patch
removes the function and all references to it from the driver.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Three functions were left in the code that are no longer used. I am removing
these functions just to keep the code clean.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The igb_mta_set function was not being correctly used
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch changes the PCS configuration for serdes so that the flow
control options change be set via the ethtool -A option.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
With a fiber or serdes NIC installed the driver was causing a null pointer
dereference on driver unload.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The internal name was used in comments, replaced with silicon part number.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The L1 hardware contains a bug that flags a fragmented IP packet
as having an incorrect TCP/UDP checksum, even though the packet
is perfectly valid and its checksum is correct. There's no way to
distinguish between one of these good packets and a packet that
actually contains a TCP/UDP checksum error, so all we can do is
allow the packet to be handed up to the higher layers and let it
be sorted out there.
Add a comment describing this condition and remove the code that
currently fails to handle what may or may not be a checksum error.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There are currently no devices supported by the e1000e driver which need
ioport resources, remove the test for it and all unnecessary code
associated with it (struct e1000_adapter elements, local variables, etc.)
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
a few people seem to have problems maintaining gigabit link
and it was root caused to an interaction between the managability
firmware on the host and the driver, not communicating.
The form of communication they use is the drv_load bit.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
82573 EEPROMs have been shipped out with known issues. While most
people will never see the issues some people do and we know
how to address them. Warn the user if we find one of these
EEPROM issues.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The ndev_* printk's are too lenghty and we don't need to specify
the adapter/netdev struct at all, making this a lot more readable.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Set 64bits consistent DMA mask since it improves performance
in some cases. No need to check the return value since it is
not required for the driver to work.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add ethernet-related fields to struct mlx4_cqe so that the mlx4_en
ethernet NIC driver can share the same definition.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The bogus code to call into the n_tty layer got removed in commit
8bc5fb6abb ("Remove bogons from the
iSeries console"), but it left a now uninitialized "return ret;" around.
Not that this code has ever even compiled since the BKL pushdown, since
not only is "ret" no longer initialized, it was never actually declared
even originally.
Replace it with a "return -ENOIOCTLCMD"
Pointed-out-by: Paul Mackerras <paulus@samba.org>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The it8705 chip supports 16-bit fan tachometers in revisions at least
>= 0x03 (Version G). This patch enables 16-bit fan readings on all
revisions >= 0x03 just like the it8712, it8716, and it8718 chips.
Signed-off-by: Andrew Paprocki <andrew@ishiboo.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The it8712 chip supports 16-bit fan tachometers in revisions >= 0x07.
Revisions >= 0x08 dropped support for 8-bit fan divisor registers. The
patch enables 16-bit fan readings on all revisions >= 0x07 just like
the it8716 and it8718 chips.
Signed-off-by: Andrew Paprocki <andrew@ishiboo.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
AMD NPT 0Fh cpus use 6 bit VID codes. Successive codes with msb 0
describe 25mV decrements, while those with msb 1 describe 12.5mV
decrements. Existing hwmon-vid.c is correct only for codes with msb 0;
add support for the codes with msb 1.
Ref:
p 309, Table 71
AMD Publication 32559, BIOS and Kernel Developer's Guide for AMD NPT Family 0Fh Processors
http://www.amd.com/us-en/assets/content_type/white_papers_and_tech_docs/32559.pdf
Signed-off-by: Frank Myhr <fmyhr@fhmtech.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Driver for the Analog Devices AD7414 temperature monitoring chip.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add critical temperature limits to the driver. These limits are read
only.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The adm9240 driver is in the kernel for three years now, time to
remove the EXPERIMENTAL dependency.
Signed-off-by: Grant Coady <gcoady.lk@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Drop the reset parameter of the w83627hf driver. It seems it wasn't
that useful. It was dropped from the Linux 2.4 version of this driver
back in July 2004.
The only users who have reported that they were still using this
parameter, needed it to switch the chip from automatic fan speed
control back to manual mode. Now that the driver creates pwmN_enable
sysfs files, users will be able to use these files instead, which is
way less agressive.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Dominik Geyer <dominik.geyer@gmx.de>
Adds support for pwm_enable sysfs interface for the w83627hf driver.
Signed-off-by: Dominik Geyer <dominik.geyer@gmx.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Update w83791d with fan bits in vbat mon register (7.48 of the
datasheet). This change allows all fans to have a divisor of 128,
and fixes a problem with incorrectly reported fan speeds.
Signed-off-by: Marc Hulsman <m.hulsman@tudelft.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
These functions aren't used before being defined, so there's no point
in forward-declaring them.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Add support for the SCH5027. The differences to the DME1737 are:
- No support for programmable temp offsets
- In auto mode, PWM outputs stay on min value if temp goes below low threshold
and can't be programmed to fully turn off
- Different voltage scaling
- No VID input
Signed-off-by: Juerg Haefliger <juergh@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Skip the checking of the device ID register in the hwmon register
block if the force_id option is used.
Signed-off-by: Juerg Haefliger <juergh@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fix names of attribute structs to make them more consistent with the
rest of the code. Minor comment changes.
Signed-off-by: Juerg Haefliger <juergh at gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
commit 9e98966c7b (tty: rework break handling)
forgot to update one exit point of rs_break() in the Amiga serial driver.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
firewire: Preserve response data alignment bug when it is harmless
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] Update generic config
[IA64] Fix uniprocessor build w.r.t. SGI_XP and SGI_GRU
[IA64] Eliminate trailing backquote in IA64_SGI_UV
[IA64] update generic_defconfig to support sn2.
[IA64] update generic_defconfig for 2.6.27-rc1
[IA64] Allow ia64 to CONFIG_NR_CPUS up to 4096
[IA64] Cleanup generated file not ignored by .gitignore
[IA64] pv_ops: fix ivt.S paravirtualization
The iSeries driver calls into the n_tty ldisc code directly for some
bizarre reason. I previously tagged this with a query but this actually
does need fixing as n_tty methods when you have a different ldisc set are
not a good thing to call.
In n_tty mode this change should have no effect, the core tty layer has
always called the ldisc ioctl method *anyway* and will call the one for
the right ldisc.
Signed-off-by: Alan Cox <alan@redhat.com>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This brings the watchdog drivers into line with coding style.
This patch takes cares of the indentation as described in chapter 1.
Main changes:
* Re-structure the ioctl switch call for all drivers as follows:
switch (cmd) {
case WDIOC_GETSUPPORT:
case WDIOC_GETSTATUS:
case WDIOC_GETBOOTSTATUS:
case WDIOC_GETTEMP:
case WDIOC_SETOPTIONS:
case WDIOC_KEEPALIVE:
case WDIOC_SETTIMEOUT:
case WDIOC_GETTIMEOUT:
case WDIOC_GETTIMELEFT:
default:
}
This to make the migration from the drivers to the uniform watchdog
device driver easier in the future.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This brings the watchdog drivers into line with coding style.
This patch takes cares of the indentation as described in chapter 1:
The preferred way to ease multiple indentation levels in a switch
statement is to align the "switch" and its subordinate "case"
labels in the same column instead of "double-indenting" the "case"
labels.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The mpc8xxx_wdt driver is using two registers: SWSRR to push magic
numbers, and SWCRR to control the watchdog. Both registers are available
on the MPC8xx, and seem to have the same offsets and semantics as in
MPC83xx/MPC86xx watchdogs. The only difference is prescale value. So
this driver simply works on the MPC8xx CPUs.
One quirk is needed for the MPC8xx, though. It has small prescale value
and slow CPU, so the watchdog resets board prior to the driver has time to
load. To solve this we should split initialization in two steps: start
ping the watchdog early, and register the watchdog userspace interface
later.
MPC823 seem to be the first CPU in MPC8xx line, so we use fsl,mpc823-wdt
compatible matching.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Tested-by: Jochen Friedrich <jochen@scram.de>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
CC drivers/watchdog/mpc8xxx_wdt.o
drivers/watchdog/mpc8xxx_wdt.c: In function 'mpc8xxx_wdt_ioctl':
drivers/watchdog/mpc8xxx_wdt.c:156: error: 'cmd' undeclared (first use in this function)
drivers/watchdog/mpc8xxx_wdt.c:156: error: (Each undeclared identifier is reported only once
drivers/watchdog/mpc8xxx_wdt.c:156: error: for each function it appears in.)
drivers/watchdog/mpc8xxx_wdt.c: At top level:
drivers/watchdog/mpc8xxx_wdt.c:176: warning: initialization from incompatible pointer type
This patch ought to be folded into
mpc8xxx_wdt-various-renames-mostly-s-mpc83xx-mpc8xxx-g.patch
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
mpc83xx_wdt.c renamed to mpc8xxx_wdt.c, now we can do various renames in
the file itself.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Rename the driver because now we support some MPC86xx processors.
There are no changes to the mpc83xx_wdt.c file, yet. When possible, we do
file renames and changes separately (because Linus once asked so, because
it helps git to track the renamed files).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
On MPC86xx the watchdog could be enabled only at power-on-reset, and could
not be disabled afterwards. We must ping the watchdog from the kernel
until the userspace handles it.
MPC83xx CPUs are only differ in a way that watchdog could be disabled
once, but after it was enabled via software it becomes just the same as
MPC86xx.
Thus, to support MPC86xx I added the kernel timer which pings the watchdog
until the userspace opens it.
Since we implemented the timer, now we're able to implement proper
handling for the CONFIG_WATCHDOG_NOWAYOUT case, for MPC83xx and MPC86xx.
Also move the probe code into subsys_initcall, because we want start
pinging the watchdog ASAP, and misc devices are available in
subsys_initcall.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
This patch simply converts mpc83xx_wdt to the OF platform driver so we can
directly work with the device tree without passing various stuff through
platform data.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Fix them up. Once we know the long term plan the watchdogs can all get
shrunk massively anyway
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Use #include <linux/io.h> instead of <asm/io.h>
Use #include <linux/uaccess.h> instead of <asm/uaccess.h>
Clean-up includes.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Merge branch 'alan' of ../linux-2.6-watchdog-mm
Fixed Conflicts in the following files:
drivers/watchdog/booke_wdt.c
drivers/watchdog/mpc5200_wdt.c
drivers/watchdog/sc1200wdt.c
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch makes the needlessly global blkif_ioctl() static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Bug fix. If SCSI tape support is turned off we get an implicit declaration
of cciss_unregister_scsi error in cciss_remove_one.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch adds support for multi-lun devices in a SAS environment. It's
required for the support of media changers.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch changes way we notify the scsi layer that something has changed
on the SCSI tape side of the driver. The user can now just tell the driver
to rescan a particular controller rather than having to know the SCSI nexus
to echo into the SCSI mid-layer.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch fixes a problem where the logical volume count may go negative.
In some instances if several logical are configured on a controller and all
of them are deleted using the online utilities the volume count in /proc may
go negative with no way get it correct again.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch removes redundant code where ever logical volumes are added or
removed. It adds 3 new functions that are called instead of having the same
code spread throughout the driver. It also removes the cciss_getgeometry
function.
The patch is fairly complex but we haven't figured out how to make it any
simpler and still do everything that needs to be done. Some of the
complexity comes from having to special case booting from cciss. Otherwise
the gendisk doesn't get added in time and the switchroot will fail.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch makes the rebuild_lun_table smart enough to not rip a logical
volume out from under the OS. Without this fix if a customer is running
hpacucli to monitor their storage the driver will blindly remove and re-add
the disks whenever the utility calls the CCISS_REGNEWD ioctl. Unfortunately,
both hpacucli and ACUXE call the ioctl repeatedly. Customers have reported
IO coming to a standstill. Calling the ioctl is the problem, this patch is
the fix.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Return -EFAULT instead of -ENOMEM if copy_from_user() fails.
Signed-off-by: Nikanth Karthikesan <knikanth@suse.de>
Acked-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Data buffers on the stack are not allowed for USB I/O. Use dynamically
allocated buffers instead.
Signed-off-by: Bruce Schmid <duck@freescale.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
PXA suspend switches off DMA core, which loses all context
of previously assigned descriptors. As pxa_camera driver
relies on DMA transfers, setup the lost descriptors on
resume and retrigger frame acquisition if needed.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add suspend/resume hooks to call soc operation specific
suspend and resume functions. This ensures the camera
chip has been previously resumed, as well as the camera
bus.
These hooks in camera chip drivers should save/restore
chip context between suspend and resume time.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
So, platform_driver_unregister() doesn't actually have a return value,
nor do any of the void __exit routines. It's reassuring to know that
people copy and paste blindly. This completely blew up my compiler.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
quoting Robert Lowery:
I think I've found the cause of the oops.
[...]
BTW it appears I have fixed my tuning problems with the updated patch
below. This reverts a change Mauro made a while back.
All is good now :)
[...]
The good news is that I've got a better patch that definitely works this
time and even better, makes use of the standard firmware (rather than
the Australian specific one).
...based on an earlier patch by Hans-Frieder Vogt:
http://www.linuxtv.org/pipermail/linux-dvb/2008-May/026280.html
Signed-off-by: Robert Lowery <rlowery@exemail.com.au>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Bad mini/max check in setting control values (the gamma in
zc3xx could be set to null).
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The crash is due to USB exchanges done at interrupt level.
These exchanges, tied to autogain, are now done by the application.
Also, there is a fix about autogain start.
Concerned subdrivers: etoms, pac7311, sonixj and spca561.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The hflip and vflip controls work for ov519 - ov7670 only.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Pinnacle Hybrid Pro (2304:0226) requires mts_firmware flag to have any
sound. Without this flag it is useful only for watching silent movies.
Signed-off-by: Eugeniy Meshcheryakov <eugen@debian.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This option is changed to GSPCA_DEBUG and it is set by default in gspca.h.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The values from win traces do not seem to work while the webcams
did work with gspca v1.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The hflip and vflip controls work for ov7670 only.
This bridge/sensor inverts blue and red - not fixed.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch fixes the following compile errors:
<-- snip -->
...
CC [M] drivers/media/video/arv.o
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/media/video/arv.c: In function 'ar_ioctl':
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/media/video/arv.c:544: error: implicit declaration of function 'video_usercopy'
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/media/video/arv.c: At top level:
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/media/video/arv.c:758: error: unknown field 'type' specified in initializer
make[4]: *** [drivers/media/video/arv.o] Error 1
<-- snip -->
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Also for the new DVB_DRX397XD driver the FW_LOADER select and the
corresponding dependency on HOTPLUG can be removed.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The pixel format should have been changed in changeset 6de914aaad86.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Set back some values of gspcav1 in init of sonixj sensor ov7660.
Add some comments.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Change function name in kernel-doc and add kernel-doc for parameter @index:
Warning(linhead//drivers/media/video/videodev.c:2090): No description found for parameter 'index'
Also change source file name in DocBook/videobook.tmpl to match the new
source file name.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
drivers/input/serio/i8042-sparcio.h:95: warning: 'sparc_i8042_driver'
defined but not used
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This re-introduces commit 2b14290078,
which was reverted due to the regression it caused by commit
fca082c9f1.
That regression was not root-caused by the original commit, it was just
uncovered by it, and the real fix was done by Alan Stern in commit
580da34847 ("Fix USB storage hang on
command abort").
We can thus re-introduce the change that was confirmed by Alan Jenkins
to be still required by his odd card reader.
Cc: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (78 commits)
AX.25: Fix sysctl registration if !CONFIG_AX25_DAMA_SLAVE
pktgen: mac count
pktgen: random flow
bridge: Eliminate unnecessary forward delay
bridge: fix compile warning in net/bridge/br_netfilter.c
ipv4: remove unused field in struct flowi (include/net/flow.h).
tg3: Fix 'scheduling while atomic' errors
net: Kill plain NET_XMIT_BYPASS.
net_sched: Add qdisc __NET_XMIT_BYPASS flag
net_sched: Add qdisc __NET_XMIT_STOLEN flag
iwl3945: fix merge mistake for packet injection
iwlwifi: grap nic access before accessing periphery registers
iwlwifi: decrement rx skb counter in scan abort handler
iwlwifi: fix unhandled interrupt when HW rfkill is on
iwlwifi: implement iwl5000_calc_rssi
iwlwifi: memory allocation optimization
iwlwifi: HW bug fixes
p54: Fix potential concurrent access to private data
rt2x00: Disable link tuning in rt2500usb
iwlwifi: Don't use buffer allocated on the stack for led names
...
mips allmodconfig:
drivers/media/video/vino.c: In function `vino_free_buffer_with_count':
drivers/media/video/vino.c:811: warning: passing arg 1 of `virt_to_phys' makes pointer from integer without a cast
drivers/media/video/vino.c: In function `vino_allocate_buffer':
drivers/media/video/vino.c:889: warning: passing arg 1 of `virt_to_phys' makes pointer from integer without a cast
drivers/media/video/vino.c: In function `vino_ioctl':
drivers/media/video/vino.c:4364: error: implicit declaration of function `video_usercopy'
The patch fixes the error, but not the warnings.
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/video/aty/atyfb_base.c:2663: warning: 'aty_resume_chip' defined
but not used
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Cc: Ville Syrjala <syrjala@sci.fi>
Cc: Antonino A. Daplas <adaplas@pol.net>
Cc: Mark Asselstine <asselsm@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
of_node_put is needed before discarding a value received from
of_find_node_by_type, eg in error handling code.
The semantic patch that makes the change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
struct device_node *n;
struct device_node *n1;
struct device_node *n2;
statement S;
identifier f1,f2;
expression E1,E2;
constant C;
@@
n = of_find_node_by_type(...)
...
if (!n) S
... when != of_node_put(n)
when != n1 = f1(n,...)
when != E1 = n
when any
when strict
(
+ of_node_put(n);
return -C;
|
of_node_put(n);
|
n2 = f2(n,...)
|
E2 = n
|
return ...;
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Timur Tabi <timur@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The name of the i2c buses shows in the output of "i2cdetect -l", so
it's important to give informative names.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the 'clear' command is used on the frame buffer with a logo the upper
area is filled by few lines but not scrolled anymore.
Fix this by removing the protected area for the logo if any part of the
logo is cleared.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I have a new PCI-E radeon RV380 series card (PCI device ID 5b64) that
hangs in my sparc64 boxes when the init scripts set the font. The problem
goes away if I disable acceleration.
I haven't figured out that bug yet, but along the way I found some
corrections to make based upon some auditing.
1) The RB2D_DC_FLUSH_ALL value used by the kernel fb driver
and the XORG video driver differ. I've made the kernel
match what XORG is using.
2) In radeonfb_engine_reset() we have top-level code structure
that roughly looks like:
if (family is 300, 350, or V350)
do this;
else
do that;
...
if (family is NOT 300, OR
family is NOT 350, OR
family is NOT V350)
do another thing;
this last conditional makes no sense, is always true,
and obviously was likely meant to be "family is NOT
300, 350, or V350". So I've made the code match the
intent.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the missing MODULE_ALIAS() to the pwm_backlight driver.
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make the error paths in the pwm_backlight driver more informative in the
probe path, especially for the times that it finds an error.
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since we use the write complete interrupt, wait for it
to complete before sleeping so we don't wake right back up due to it
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds an SPI driver for the SPI controller found in various Marvell
Orion ARM SoCs. It currently supports only one slave, which must use SPI
mode 0.
[dbrownell@users.sourceforge.net: cleanups, meet specs, pass "sparse"]
Signed-off-by: Shadi Ammouri <shadi@marvell.com>
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
curr_queue is a local variable in a for loop, and it's being initialized
at the start of each loop. So any assignment at the end of the loop is
pointless.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Cc: Mike Miller <mike.miller@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
commit 20e061fb75
Author: Ondrej Zajicek <santiago@crfreenet.org>
Date: Mon Apr 28 02:15:18 2008 -0700
fbdev: framebuffer_alloc() fixes
Correct the dev arg of framebuffer_alloc() in arkfb, s3fb and vt8623fb.
causes a null-pointer deref because "info->dev is NULL, info was just
kzallocated".
Signed-off-by: Ondrej Zajicek <santiago@crfreenet.org>
Reported-by: "MadLoisae@gmx.net" <MadLoisae@gmx.net>
Tested-by: "MadLoisae@gmx.net" <MadLoisae@gmx.net>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: <stable@kernel.org> [2.6.26.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Okay, I found the cause of the hang. It is a simple bug in the USB
scatter-gather library, caused by changes added in response to the S-G
chaining modification.
This patch (as1125) fixes a bug in the USB scatter-gather library.
Early exit from the S-G initialization loop does not reset the count of
outstanding URBs.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that we have warm-plug support ->cable_detect method no longer
can be be marked __devinit.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Now that we have warm-plug support ->quirkproc method no longer
can be be marked __devinit.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Based on sparse comments in OpenFirmware code
(no Cx5510/Cx5520 datasheet here).
This fixes 2.6.26 regression reported by TAKADA
and caused by addition of warm-plug support.
Tested-by: TAKADA Yoshihito <takada@mbf.nifty.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
According to MMC-3 (or any later versions) READ TOCs are mandatory
commands and have nothing to do with CDC_PLAY_AUDIO. I have no idea why
the check was put there in the first place but it now only breaks
automatic actions on certain drives.
Note that this test was only effective when ide-cdrom was being used
as sr didn't mask CDC_PLAY_AUDIO according to the capabilities.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Aesthetic regards aside, commit e8e7b9eb11
still leaves a bug in the error message, because it uses the unconverted
big-endian value for printk.
Fix this by using a local variable in machine byte order. The result is
correct, more readable, and also produces slightly shorter code on i386.
Signed-off-by: Petr Tesarik <ptesarik@suse.cz>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: <stable@kernel.org>
Acked-by: Borislav Petkov <petkovbb@gmail.com>
[bart: __u32 -> u32]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The benefits of a user settable CONFIG_IDE_MAX_HWIFS have become pretty
tiny and are no longer considered worth the trouble of an own option.
Simply always #define MAX_HWIFS to 10.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
On Monday 28 July 2008, Benjamin Herrenschmidt wrote:
[...]
> Vector: 300 (Data Access) at [c58b7b80]
> pc: c014f264: elv_may_queue+0x10/0x44
> lr: c0152750: get_request+0x2c/0x2c0
> sp: c58b7c30
> msr: 1032
> dar: c
> dsisr: 40000000
> current = 0xc58aaae0
> pid = 854, comm = media-bay
> enter ? for help
> mon> t
> [c58b7c40] c0152750 get_request+0x2c/0x2c0
> [c58b7c70] c0152a08 get_request_wait+0x24/0xec
> [c58b7cc0] c0225674 ide_cd_queue_pc+0x58/0x1a0
> [c58b7d40] c022672c ide_cdrom_packet+0x9c/0xdc
> [c58b7d70] c0261810 cdrom_get_disc_info+0x60/0xd0
> [c58b7dc0] c026208c cdrom_mrw_exit+0x1c/0x11c
> [c58b7e30] c0260f7c unregister_cdrom+0x84/0xe8
> [c58b7e50] c022395c ide_cd_release+0x80/0x84
> [c58b7e70] c0163650 kref_put+0x54/0x6c
> [c58b7e80] c0223884 ide_cd_put+0x40/0x5c
> [c58b7ea0] c0211100 generic_ide_remove+0x28/0x3c
> [c58b7eb0] c01e9d34 __device_release_driver+0x78/0xb4
> [c58b7ec0] c01e9e44 device_release_driver+0x28/0x44
> [c58b7ee0] c01e8f7c bus_remove_device+0xac/0xd8
> [c58b7f00] c01e7424 device_del+0x104/0x198
> [c58b7f20] c01e74d0 device_unregister+0x18/0x30
> [c58b7f40] c02121c4 __ide_port_unregister_devices+0x6c/0x88
> [c58b7f60] c0212398 ide_port_unregister_devices+0x38/0x80
> [c58b7f80] c0208ca4 media_bay_step+0x1cc/0x5c0
> [c58b7fb0] c0209124 media_bay_task+0x8c/0xcc
> [c58b7fd0] c00485c0 kthread+0x48/0x84
> [c58b7ff0] c0011b20 kernel_thread+0x44/0x60
The guilty commit turned out to be 08da591e14
("ide: add ide_device_{get,put}() helpers"). ide_device_put() is called
before kref_put() in ide_cd_put() so IDE device is already gone by the time
ide_cd_release() is reached.
Fix it by calling ide_device_get() before kref_get() and ide_device_put()
after kref_put() in all affected device drivers.
v2:
Brown paper bag time. In v1 cd->drive was referenced after dropping last
reference on cd object (which could result in OOPS in ide_device_put() as
reported/debugged by Mariusz Kozlowski). Fix it by caching cd->drive in
the local variable (fix other device drivers too).
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reported-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Borislav Petkov <petkovbb@gmail.com>
Tested-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Tested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix byte-swapping for id->words161_175[], id->words206_254[]
and id->words206_254[].
Luckily all words previously left in little-endian byte-order
are marked as reserved so this fix shouldn't affect user-space
applications.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
id->tDMA is of 'unsigned char' type so endianness is already
correct and calling le16_to_cpu() is wrong.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Update all avr32-specific files to use the new platform-specific header
locations. Drivers shared with ARM are left alone for now.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This patch fixes the 'scheduling while atomic' errors introduced by
commit 12dac0756d ("tg3: adapt tg3 to
use reworked PCI PM code").
The first hunk of the patch removes an unnecessary
tg3_set_power_state() call. The chip will already be in the D0 state
either due to a chip reset or through a previous call to
tg3_set_power_state().
The second hunk of the patch moves the tg3_set_power_state() call
outside the critical section guarded by tg3_full_lock() and
tg3_full_unlock() functions. The power state of the device is and
should be outside the lock's domain and all other
tg3_set_power_state() calls support this.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The raid10 resync/recovery code currently limits the amount of
in-flight resync IO to 2Meg. This was copied from raid1 where
it seems quite adequate. However for raid10, some layouts require
a bit of seeking to perform a resync, and allowing a larger buffer
size means that the seeking can be significantly reduced.
There is probably no real need to limit the amount of in-flight
IO at all. Any shortage of memory will naturally reduce the
amount of buffer space available down to a set minimum, and any
concurrent normal IO will quickly cause resync IO to back off.
The only problem would be that normal IO has to wait for all resync IO
to finish, so a very large amount of resync IO could cause unpleasant
latency when normal IO starts up.
So: increase RESYNC_DEPTH to allow 32Meg of buffer (if memory is
available) which seems to be a good amount. Also reduce the amount
of memory reserved as there is no need to keep 2Meg just for resync if
memory is tight.
Thanks to Keld for the suggestion.
Cc: Keld Jørn Simonsen <keld@dkuug.dk>
Signed-off-by: NeilBrown <neilb@suse.de>
Removing faulty devices from an array is a two stage process.
First the device is moved from being a part of the active array
to being similar to a spare device. Then it can be removed
by a request from user space.
The first step is currently not performed for read-only arrays,
so the second step can never succeed.
So allow readonly arrays to remove failed devices (which aren't
blocked).
Signed-off-by: NeilBrown <neilb@suse.de>
When we have externally managed metadata, we need to mark a failed
device as 'Blocked' and not allow any writes until that device
have been marked as faulty in the metadata and the Blocked flag has
been removed.
However it is perfectly OK to allow read requests when there is a
Blocked device, and with a readonly array, there may not be any
metadata-handler watching for blocked devices.
So in raid5/raid6 only allow a Blocked device to interfere with
Write request or resync. Read requests go through untouched.
raid1 and raid10 already differentiate between read and write
properly.
Signed-off-by: NeilBrown <neilb@suse.de>
We cannot currently change the size of a write-intent bitmap.
So if we change the size of an array which has such a bitmap, it
tries to set bits beyond the end of the bitmap.
For now, simply reject any request to change the size of an array
which has a bitmap. mdadm can remove the bitmap and add a new one
after the array has changed size.
Signed-off-by: NeilBrown <neilb@suse.de>
A recent patch allowed do_md_stop to know whether it was being called
via an ioctl or not, and thus where to allow for an extra open file
descriptor when checking if it is in use.
This broke then switch to readonly performed by the shutdown notifier,
which needs to work even when the array is still (apparently) active
(as md doesn't get told when the filesystem becomes readonly).
So restore this feature by pretending that there can be lots of
file descriptors open, but we still want do_md_stop to switch to
readonly.
Signed-off-by: NeilBrown <neilb@suse.de>
If we reduce the 'safe_mode_delay', it could still wait for the old
delay to completely expire before doing anything about safe_mode.
Thus the effect if the change is delayed.
To make the effect more immediate, run the timeout function
immediately if the delay was reduced. This may cause it to run
slightly earlier that required, but that is the safer option.
Signed-off-by: NeilBrown <neilb@suse.de>
Converting page lock to new locking bitops requires a change of page flag
operation naming, so we might as well convert it to something nicer
(!TestSetPageLocked_Lock => trylock_page, SetPageLocked => set_page_locked).
This also facilitates lockdeping of page lock.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (29 commits)
sh: enable maple_keyb in dreamcast_defconfig.
SH2(A) cache update
nommu: Provide vmalloc_exec().
add addrespace definition for sh2a.
sh: Kill off ARCH_SUPPORTS_AOUT and remnants of a.out support.
sh: define GENERIC_HARDIRQS_NO__DO_IRQ.
sh: define GENERIC_LOCKBREAK.
sh: Save NUMA node data in vmcore for crash dumps.
sh: module_alloc() should be using vmalloc_exec().
sh: Fix up __bug_table handling in module loader.
sh: Add documentation and integrate into docbook build.
sh: Fix up broken kerneldoc comments.
maple: Kill useless private_data pointer.
maple: Clean up maple_driver_register/unregister routines.
input: Clean up maple keyboard driver
maple: allow removal and reinsertion of keyboard driver module
sh: /proc/asids depends on MMU.
arch/sh/boards/mach-se/7343/irq.c: removed duplicated #include
arch/sh/boards/board-ap325rxa.c: removed duplicated #include
sh/boards/Makefile typo fix
...
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
powerpc: Remove use of CONFIG_PPC_MERGE
powerpc: Force printing of 'total_memory' to unsigned long long
powerpc: Fix compiler warning in arch/powerpc/mm/mem.c
powerpc: Move include files to arch/powerpc/include/asm
drivers/watchdog/wdt_pci.c: In function 'wdtpci_ctr_mode':
drivers/watchdog/wdt_pci.c:120: error: implicit declaration of function 'udelay'
{standard input}: Assembler messages:
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kill off use of semaphores.
Fix ioctl races and locking holes.
From: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2.6.26 corrected the mutex locking on tty resizing to fix the case where
you could get the tty/vt sizing out of sync. That turns out to have a
deadlock.
The actual fix is really major and I've got it lined up as part of the ops
changes for 2.6.28 so for 2.6.26/2.6.27 it is safer to reintroduce this
ages old minor bug.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It now compiles with the tty changes but isn't tested (which has to be
better than not compiling..
Closes bug #11218
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Blackfin peers into the ldisc in an odd way for IRDA snooping which
therefore got missed. Simple enough fix.
Closes bug #11233
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/kkeil/ISDN-2.6:
Add DIP switch readout for HFC-4S IOB4ST
Fix remaining big endian issue of hfcmulti
mISDN cleanup user interface
mISDN fix main ISDN Makefile
For some time my at91sam9260 board with JFFS2 on serial flash (m25p80)
would hang when accessing the serial flash and SPI bus. Slowing the SPI
clock down to 9 MHz reduced the occurrence of the hang from "always"
during boot to a nuisance level that allowed other SW development to
continue. Finally had to address this issue when an application stresses
the I/O to always cause a hang.
Hang seems to be caused by a missed SPI interrupt, so that the task ends
up waiting forever after calling spi_sync(). The fix has 2 parts. First
is to halt the DMA engine before the "current" PDC registers are loaded.
This ensures that the "next" registers are loaded before the DMA operation
takes off. The second part of the fix is a kludge that adds a
"completion" interrupt in case the ENDRX interrupt for the last segment of
the DMA chaining operation was missed.
The patch allows the SPI clock for the serial flash to be increased from 9
MHz to 15 MHz (or more?). No hangs or SPI overruns were encountered.
Haavard: while this patch does indeed improve things, I still see overruns
and CRC errors on my NGW100 board when running the DataFlash at 10 MHz.
However, I think some improvement is better than nothing, so I'm passing
this on for inclusion in 2.6.27.
Signed-off-by: Gerard Kam <gerardk5@verizon.net>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a bug in the spi_s3c24xx driver where it does not reset the registers
of the hardware when resuming from suspend (this block has been reset over
suspend).
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit 2b14290078, since it
seems to break some other USB storage devices (at least a JMicron USB to
ATA bridge). As such, while it apparently fixes some cardreaders, it
would need to be made conditional on the exact reader it fixes in order
to avoid causing regressions.
Cc: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The SGI XP and GRU drivers only work on SMP systems ... the Kconfig
file only disallowed them for non-SMP X86.
Signed-off-by: Tony Luck <tony.luck@intel.com>
We should allow packets transmission in monitor mode for 3945. The
patch fixes a merge error with 2.6.26 kernel.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We need to grap nic access before accessing periphery registers.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch decrements rx skb counter in scan abort handler.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes unhandled interrupt when HW rfkill is on during
devices start up. The behavior changes, now open is successful even
when rfkill is on. This is to align with the situation when rfkill
is set on after opening.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch implements rssi calculation for 5000 HW.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch optimizes memory allocation. The cmd member of
iwl_tx_queue was allocated previously as a continuous block
of memory. This patch allocates separate memory chunks for each command
and maps/unmaps these chunks in the run time.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds few HW bug fixes.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Experience with the rtl8187 driver has shown that mac80211 can make
calls to the config callback routine in rapid succession. This patch
creates a mutex that protects the private data in several of the routines
called by mac80211.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the legacy rt2570 driver the link tuner was never
really called. And now the reason has finally become
apparent: It breaks TX capabilities
As soon as the device has been associated all following
TX frames will be queued in the hardware and never transmitted
to the air. Disabling sections of the link tuner did not
have the expected result, but completely disabling the
link tuner did have the right result (Both of my rt2570 devices
came back to life).
This should fix Fedora bug: 411481
v2: Fix typos
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Having the buffer on the stack and even re-using it for all led devices is bad.
Not being able to resolve the name member of the led device structure to a
meaningful value leads to confusion during ad-hoc debugging and potential
breakage in the future, if we ever decide to access the name member outside of
the registration function. Move the buffer to our private per led device
structures so that it is accessible after registration.
A quick grep didn't yield any occurence of using the led device name parameter
outside of the led device registration function, so currently we should already
be safe for normal operation.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
Cc: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch renames driver name from 4965 to AGN
The driver supports both 4965AGN and 5000AGN family
The driver's original module name iwl4965.ko remains as an alias
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes errors reported by checkpatch in iwlwifi drivers
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch renames iwl4965-base.c to iwl-agn.c
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch uses dtim_period from association, and sets the listen_interval.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwl-agn-rs.c: In function 'rs_clear':
iwl-agn-rs.c:2405: warning: unused variable 'priv
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug in AGG flow:
u64 bitmap = 0;
bitmap |= 1 << 32 results to be 0xffffffff80000000.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch sets the led register in disassociation flow according to
rf-kill state : off - in case of rf_kill, on - otherwise.
Signed-off-by: Esti Kummer <ester.kummer@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwl4965_fill_rs_info was used in sysfs. This info is already present
in iwl-agn-rs debugfs.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch renames iwl-4965-rs to iwl-agn-rs as it provides
rate scale capability for all AGN capable iwlwifi drivers.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves iwl4965_set_pwr_src to iwl4965-base.c.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch concentrates becaon handling in iwl4965-base.c.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves iwl4965_mac_ampdu_action to iwl4965-base.c.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch corrects power_level in sysfs.
Signed-off-by: Esti Kummer <ester.kummer@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for power save for 5000 HW.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ipath_driver.c:1260: warning: format '%Lx' expects type 'long long unsigned int', but argument 6 has type 'long unsigned int'
ipath_driver.c:1459: warning: format '%Lx' expects type 'long long unsigned int', but argument 4 has type 'u64'
ipath_intr.c:358: warning: format '%Lx' expects type 'long long unsigned int', but argument 3 has type 'u64'
ipath_intr.c:358: warning: format '%Lu' expects type 'long long unsigned int', but argument 6 has type 'u64'
ipath_intr.c:1119: warning: format '%Lx' expects type 'long long unsigned int', but argument 5 has type 'u64'
ipath_intr.c:1119: warning: format '%Lx' expects type 'long long unsigned int', but argument 3 has type 'u64'
ipath_intr.c:1123: warning: format '%Lx' expects type 'long long unsigned int', but argument 3 has type 'u64'
ipath_intr.c:1130: warning: format '%Lx' expects type 'long long unsigned int', but argument 4 has type 'u64'
ipath_iba7220.c:1032: warning: format '%llx' expects type 'long long unsigned int', but argument 4 has type 'u64'
ipath_iba7220.c:1045: warning: format '%llX' expects type 'long long unsigned int', but argument 3 has type 'u64'
ipath_iba7220.c:2506: warning: format '%Lu' expects type 'long long unsigned int', but argument 4 has type 'u64'
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Running 'ifconfig up' on the cxgb3 interface with iw_cxgb3 loaded
causes a deadlock. The rtnl lock is already held in this path. The
function fw_supports_fastreg() was introduced in 2.6.27 to
conditionally set the IB_DEVICE_MEM_MGT_EXTENSIONS bit iff the
firmware was at 7.0 or greater, and this function also acquires the
rtnl lock and which thus causes a deadlock. Further, if iw_cxgb3 is
loaded _after_ the nic interface is brought up, then the deadlock does
not occur and therefore fw_supports_fastreg() does need to grab the
rtnl lock in that path.
It turns out this code is all useless anyway. The low level driver
will NOT allow the open if the firmware isn't 7.0, so iw_cxgb3 can
always set the MEM_MGT_EXTENSIONS bit. Simplify...
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
- MWs don't have local read/write permissions.
- Set the MW_BIND enabled bit if a MR has MW_BIND access.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
- Set the stag0 and fastreg capability bits only for kernel qps.
- QP_PRIV flag is no longer used, so don't set it.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
There are a few places where the RDMA CM code handles IPv6 by doing
struct sockaddr addr;
u8 pad[sizeof(struct sockaddr_in6) -
sizeof(struct sockaddr)];
This is fragile and ugly; handle this in a better way with just
struct sockaddr_storage addr;
[ Also roll in patch from Aleksey Senin <alekseys@voltaire.com> to
switch to struct sockaddr_storage and get rid of padding arrays in
struct rdma_addr. ]
Signed-off-by: Roland Dreier <rolandd@cisco.com>
from include/asm-powerpc. This is the result of a
mkdir arch/powerpc/include/asm
git mv include/asm-powerpc/* arch/powerpc/include/asm
Followed by a few documentation/comment fixups and a couple of places
where <asm-powepc/...> was being used explicitly. Of the latter only
one was outside the arch code and it is a driver only built for powerpc.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We can simply wrap in to the dev_set/get_drvdata(), there's no reason
to track an extra level of private data on top of the struct device.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
These were completely inconsistent. Clean these up to take a maple_driver
pointer directly for consistency.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Have a single probe function instead of a probe and a connect function.
Also tidy a comment.
Signed-off-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Allow the removal (and subsequent reinsertion) of the maple_keyb (maple
keyboard) driver by adding a working removal function.
Also tidy long lines.
Signed-off-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
No file should be explicitly referencing its own platform headers
by specifying an absolute include path. Fix these paths to use
standard <asm/arch/...> includes.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Recently, a bug having to do with the alignment of transaction response
data was fixed. However, some apps such as libdc1394 relied on the
presence of that bug in order to function correctly. In order to stay
compatible with old versions of those apps, this patch preserves the bug
in cases where it is harmless to normal operation (such as the single
quadlet read) due to a simple duplication of data. This guarantees
maximum compatability for those users who are using the old app with the
fixed kernel.
Signed-off-by: David Moore <dcm@acm.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
* git://git.infradead.org/users/dwmw2/random-2.6:
[MTD] Fix !CONFIG_BLOCK compile for mtdsuper.c
firmware: silence __fw_modbuild and __fw_modinst 'Nothing to be done' messages
The driver was not so bad at big endian at all, only the optimised fifo
read/write functions need a fix, with this fix the driver works on
a pegasus PPC machine.
Signed-off-by: Karsten Keil <kkeil@suse.de>
The channelmap should have the same size on 32 and 64 bit systems
and should not depend on endianess.
Thanks to David Woodhouse for spotting this.
Signed-off-by: Karsten Keil <kkeil@suse.de>
rt2x00usb_vendor_request_large_buff is write-only, so it is
safe to make the argument a const.
Fixes compile warning:
drivers/net/wireless/rt2x00/rt73usb.c: In function 'rt73usb_load_firmware':
drivers/net/wireless/rt2x00/rt73usb.c:916: warning: passing argument 5 of 'rt2x00usb_vendor_request_large_buff' discards qualifiers from pointer target typ
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by Adrian Bunk, commit d5686b444f
(switch mtd and dm-table to lookup_bdev()) causes the following compile
error with CONFIG_BLOCK=n:
CC drivers/mtd/mtdsuper.o
drivers/mtd/mtdsuper.c: In function `get_sb_mtd':
drivers/mtd/mtdsuper.c:184: error: implicit declaration of function 'lookup_bdev'
drivers/mtd/mtdsuper.c:184: warning: assignment makes pointer from integer without a cast
drivers/mtd/mtdsuper.c:197: error: implicit declaration of function 'bdput'
make[3]: *** [drivers/mtd/mtdsuper.o] Error 1
Fix it by putting the block device lookup inside #ifdef CONFIG_BLOCK
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Currently function tty_ldisc_get() tries to load an ldisc driver module
only when tty_ldisc_try_get() returns -EAGAIN. This happens only if
module is being unloaded. If ldisc module is not loaded
tty_ldisc_try_get() returns -EINVAL and this case is not handled in
tty_ldisc_get(), so request_module() is not called.
Attached patch fixes this by calling request_module() if
tty_ldisc_try_get() returned any error code.
I discovered this when my UMTS modem stopped working with 2.6.27-rc1
because module ppp_async was not loaded.
Signed-off-by: Eugeniy Meshcheryakov <eugen@debian.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Each resource should be printed on its own line, so start snprintf'ing
at the beginning of the buffer every time through the loop.
Also, use scnprintf() rather than snprintf() when building up the
buffer to print. scnprintf() returns the number of characters actually
written into the buffer (not including the trailing NULL).
snprintf() returns the number of characters that *would be* written,
assuming everything would fit in the buffer. That's nice if we want to
resize the buffer to make sure everything fits, but in this case, I
just want to keep from overflowing the buffer, and it's OK if the
output is truncated.
Using snprintf() meant that my "len" could grow to be more than the
the buffer size, which makes "sizeof(buf) - len" negative, which causes
this alarming WARN_ON:
http://marc.info/?l=linux-kernel&m=121736480005656&w=2
More useful snprintf/scnprintf discussion:
http://lwn.net/Articles/69419/
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Reported-by: Pete Clements <clem@clem.clem-digital.net>
Cc: Rene Herman <rene.herman@keyaccess.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some module parameters with only one line have the '\n' at the end of the
description. This is not needed nor wanted as after the description the
type (i.e. int) is followed by a newline.
Some modules contain a multi-line description, these are not affected
by this patch.
Signed-off-by: Niels de Vos <niels.devos@wincor-nixdorf.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Ed L. Cashin <ecashin@coraid.com>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Roland Dreier <rolandd@cisco.com>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
pata_it821x: Driver updates and reworking
libata.h: replace __FUNCTION__ with __func__
ata_piix: subsys 106b:00a3 is apple ich8m too
libata-core: make sure that ata_force_tbl is freed in case of an error
libata: update atapi disable handling
pata_via: add VX800 flag; add function for fixing h/w bugs
pata_ali: misplaced pci_dev_put()
asm/se.h moved to mach-se/mach/se.h, update the path. We could use
mach/se.h here also, but it's preferable to be explicit when there's
only a single supported mach-type.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
iwl3945_rx_reply_rx was sending packets too early to
mac80211, before updating signal strength/quality.
This resulted in garbage power levels.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the standard offsetof() macro to fix a compile warning below:
CC [M] drivers/net/wireless/prism54/isl_ioctl.o
drivers/net/wireless/prism54/isl_ioctl.c: In function 'prism2_ioctl_set_generic_element':
drivers/net/wireless/prism54/isl_ioctl.c:2658: warning: cast from pointer to integer of different size
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ipw_write8() can't be used alone with a loop because of a wrong definition.
CC [M] drivers/net/wireless/ipw2200.o
drivers/net/wireless/ipw2200.c: In function 'ipw_ethtool_set_eeprom':
drivers/net/wireless/ipw2200.c:10579: warning: array subscript is above array bounds
drivers/net/wireless/ipw2200.c: In function 'ipw_load':
drivers/net/wireless/ipw2200.c:2663: warning: array subscript is above array bounds
Add missing do {} while (0) to fix them.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some users of the RTL8187B have experienced difficulties since commit
49292d5635 that introduced the power
management wext hooks. This difficulty has not made much sense until
it was realized that it was possible for mac80211 to make a call to the
config routine while that routine was already being executed. On this
device, it is necessary to loopback the TX when changing channels. Unless
this is properly restored, the device will lockup. A mutex now protects
the device state, and the private data in several places.
The problem was found by Herton Ronaldo Krzesinski <herton@mandriva.com.br>,
who also suggested this type of fix.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Acked-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In kernel version 2.6.26-rc9 my wireless LAN card worked; but in the
released 2.6.26, my RaLink rt2500 card wouldn't associate.
Git-bisect led me to this patch:
61486e0f68
rt2x00: Remove ieee80211_tx_control argument from write_tx_desc()
I believe that there is a problem with that patch --- it
(inadvertantly) removes an extra line of code, that used to set the
DATABYTE_COUNT field.
This patch reinstates that line, and with it my card works again.
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since only mesh-enabled firmware has the CMD_802_11_MONITOR_MODE on
which the rtap functionality depends, only expose the rtap functionality
when mesh is also available.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The sequence counter can be accessed in IRQ context,
which means the lock protecting the counter should
be irqsave. To prevent making the entire intf->lock irqsave
without reason, create a new lock which only protects
the sequence counter.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the EEPROM_BBPTUNE_VGC word is valid, we should
override EEPROM_BBPTUNE_VGCLOWER field with the BBP
value.
And we should _not_ do that when EEPROM_BBPTUNE_R17 is valid.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After the hardware has indicated the firmware upload has completed
and the device is ready, we should wait another millisecond to
make sure the device is really ready to continue.
Without this timout, bringing the interface down and up again will
fail due to incorrect register initialization.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The if-statement to determine the new TX/RX antenna
configuration was incomplete. It lacks the general
else-clause when the antenna wasn't changed.
This is a correct event, since it can occur when only
one of the antenna's has been changed or when the new
configuration is being forced (like when the interface
has just been added).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Although most rt2x00 debugfs files don't contain
information which could compromise network security,
it is better to set the access permissions to root only.
This will be required when HW crypto is implemented,
because it could be possible to read the HW key from
the registers.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch avoids stopping queue in the middle of the fragmented packet.
It is required that there will be ~10 (max packet/min fragment) or 16
(4 bits of frag number) free tfds all the time.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mask out previously demanded interrupt flags because we set
new ones. Don't allow mixing them after switch from sta to
ibss and vice versa.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Enable I/Q calibration each time we have correction results (we
were only enabling calibration during reset). If we don't we commit
the same results each time calibration routine is called.
* Add some documentation and a TODO on nf calibration
* Return -EAGAIN on noise floor timeout/failure
Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Add channel function for RF2425 (got this from decompiling binary
HAL, i have no idea why there is a 5GHz section but i'm looking
into it)
* Update RF5112 channel function (also got this from decompiling binary HAL)
* Set JAPAN setting for channel 14 on all PHY chips
Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Add initial RF gain settings for RF2425
Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Update ath5k_hw_reset and add some more documentation about PHY calibration
* Fix ath5k_hw_set_power to use AR5K_SLEEP_CTL_SLE_ALLOW for Network sleep
* Preserve sleep duration field while setting AR5K_SLEEP_CTL
and reduce delays & checks for register's status (got this from
decompiling & dumps, it works for me but it needs testing)
Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Do an ADC test during reset to match recent regdumps
Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Update hw_reset to calculate some of the values we were using as static
* Increase activation to rx delay
Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Correctly attach RF2425
* Update SREV values for Radio chips
* Update hw_attach to use new SPENDING values
* Write a bit after POST for some chips
Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Restore saved initial value after POST
Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Update list of registers
* Use updated register macros inside hw.c, initvals.c and debug.c
Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a reverse dependency of CONFIG_SGI_XP upon CONFIG_SGI_GRU to Kconfig.
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a dependency of CONFIG_SGI_XP upon CONFIG_NET to Kconfig.
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://neil.brown.name/md:
md: raid10: wake up frozen array
md: do not count blocked devices as spares
md: do not progress the resync process if the stripe was blocked
md: delay notification of 'active_idle' to the recovery thread
md: fix merge error
md: move async_tx_issue_pending_all outside spin_lock_irq
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
md: the bitmap code needs to use blk_plug_device_unlocked()
block: add a blk_plug_device_unlocked() that grabs the queue lock
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (46 commits)
tcp: MD5: Fix IPv6 signatures
skbuff: add missing kernel-doc for do_not_encrypt
net/ipv4/route.c: fix build error
tcp: MD5: Fix MD5 signatures on certain ACK packets
ipv6: Fix ip6_xmit to send fragments if ipfragok is true
ipvs: Move userspace definitions to include/linux/ip_vs.h
netdev: Fix lockdep warnings in multiqueue configurations.
netfilter: xt_hashlimit: fix race between htable_destroy and htable_gc
netfilter: ipt_recent: fix race between recent_mt_destroy and proc manipulations
netfilter: nf_conntrack_tcp: decrease timeouts while data in unacknowledged
irda: replace __FUNCTION__ with __func__
nsc-ircc: default to dongle type 9 on IBM hardware
bluetooth: add quirks for a few hci_usb devices
hysdn: remove the packed attribute from PofTimStamp_tag
isdn: use the common ascii hex helpers
tg3: adapt tg3 to use reworked PCI PM code
atm: fix direct casts of pointers to u32 in the InterPhase driver
atm: fix const assignment/discard warnings in the ATM networking driver
net: use the common ascii hex helpers
random32: seeding improvement
...
* git://git.infradead.org/mtd-2.6:
[MTD] [NAND] drivers/mtd/nand/nandsim.c: fix printk warnings
[MTD] [NAND] Blackfin NFC Driver: Cleanup the error exit path of bf5xx_nand_probe function
[MTD] [NAND] Blackfin NFC Driver: use standard dev_err() rather than printk()
[MTD] [NAND] Blackfin NFC Driver: enable Blackfin nand HWECC support by default
[MTD] [NAND] Blackfin NFC Driver: add proper devinit/devexit markings to probe/remove functions
[MTD] [NAND] Blackfin NFC Driver: add support for the ECC layout the Blackfin bootrom uses
[MTD] [NAND] Blackfin NFC Driver: fix bug - hw ecc calc by making sure we extract 11 bits from each register instead of 10
[MTD] [NAND] Blackfin NFC Driver: fix bug - do not clobber the status from the first 256 bytes if operating on 512 pages
[MTD] [NAND] diskonchip.c fix sparse endian warnings
[MTD] [NAND] drivers/mtd/nand/nandsim.c needs div64.h
[JFFS2] Fix allocation of summary buffer
Fix rename of at91_nand -> atmel_nand
[MTD] [NOR] drivers/mtd/chips/jedec_probe.c: fix Am29DL800BB device ID
[MTD] MTD_DEBUG always does compile-time typechecks
[MTD] DataFlash: bugfix, binary page sizes now handled
[MTD] [NAND] fsl_elbc_nand.c: fix printk warning
[MTD] [NAND] nandsim: support random page read command
[MTD] [NAND] fix subpage read for small page NAND
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
[PATCH] pass struct path * to do_add_mount()
[PATCH] switch mtd and dm-table to lookup_bdev()
[patch 3/4] vfs: remove unused nameidata argument of may_create()
[PATCH] devpts: switch to IDA
[PATCH 2/2] proc: switch inode number allocation to IDA
[PATCH 1/2] proc: fix inode number bogorithmetic
[PATCH] fix bdev leak in block_dev.c do_open()
[PATCH] fix races and leaks in vfs_quota_on() users
[PATCH] clean dup2() up a bit
[PATCH] merge locate_fd() and get_unused_fd()
[PATCH] ipv4_static_sysctl_init() should be under CONFIG_SYSCTL
Re: BUG at security/selinux/avc.c:883 (was: Re: linux-next: Tree
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
au1xmmc: raise segment size limit.
mmc_block: use proper sg iterators
mmc: properly iterate over sg list in debug check
mmc_test: Revert "mmc_test: test oversized sg lists"
sdhci: check correct return value
sdhci: disable DMA for req, not completely
sdhci: handle bug in JMB38x for sizes < 4 bytes
* git://git.infradead.org/battery-2.6:
power_supply: Sharp SL-6000 (tosa) batteries support
power_supply: fix up CHARGE_COUNTER output to be more precise
power_supply: add CHARGE_COUNTER property and olpc_battery support for it
power_supply: bump EC version check that we refuse to run with in olpc_battery
power_supply: cleanup of the OLPC battery driver
power_supply: add eeprom dump file to olpc_battery's sysfs
power_supply: Support serial number in olpc_battery
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (28 commits)
mm/hugetlb.c must #include <asm/io.h>
video: Fix up hp6xx driver build regressions.
sh: defconfig updates.
sh: Kill off stray mach-rsk7203 reference.
serial: sh-sci: Fix up SH7760/SH7780/SH7785 early printk regression.
sh: Move out individual boards without mach groups.
sh: Make sure AT_SYSINFO_EHDR is exposed to userspace in asm/auxvec.h.
sh: Allow SH-3 and SH-5 to use common headers.
sh: Provide common CPU headers, prune the SH-2 and SH-2A directories.
sh/maple: clean maple bus code
sh: More header path fixups for mach dir refactoring.
sh: Move out the solution engine headers to arch/sh/include/mach-se/
sh: I2C fix for AP325RXA and Migo-R
sh: Shuffle the board directories in to mach groups.
sh: dma-sh: Fix up dreamcast dma.h mach path.
sh: Switch KBUILD_DEFCONFIG to shx3_defconfig.
sh: Add ARCH_DEFCONFIG entries for sh and sh64.
sh: Fix compile error of Solution Engine
sh: Proper __put_user_asm() size mismatch fix.
sh: Stub in a dummy ENTRY_OFFSET for uImage offset calculation.
...
Raise the DMA block size limit from 2048 bytes to the maximum supported
by the DMA controllers on the chip (64KB on Au1100, 4MB on Au1200).
This gives a very small performance boost and apparently fixes an oops
when MMC-DMA and network traffic are active at the same time.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This reverts commit 48b5352ea1. Oversized
sg lists are not allowed anymore, and the core even checks for them in
debug mode, so this test is entirely incorrect.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The wrong flag was manipulated when an invalid sg list was given, turning
off DMA on the next (and all subsequent) request instead of the current
one.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The planned move of include/asm-s390 to arch/s390/include/asm
requires that all includes for asm headers use include/asm and
not include/asm-s390.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Since git commit 3da1c84c00
"workqueues: make get_online_cpus() useable for work->func()"
it is safe to call get_online_cpus() from workqueue context.
So remove the kthread workaround again.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix these two false positive warnings:
WARNING: vmlinux.o(.text+0x2e1cc4): Section mismatch in reference from the function s390_virtio_console_init() to the function .init.text:early_put_chars()
The function s390_virtio_console_init() references
the function __init early_put_chars().
This is often because s390_virtio_console_init lacks a __init
annotation or the annotation of early_put_chars is wrong.
WARNING: vmlinux.o(.text+0x2e1cd0): Section mismatch in reference from the function s390_virtio_console_init() to the function .init.text:virtio_cons_early_init()
The function s390_virtio_console_init() references
the function __init virtio_cons_early_init().
This is often because s390_virtio_console_init lacks a __init
annotation or the annotation of virtio_cons_early_init is wrong.
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix the two section mismatch warnings below.
This fixes two real bugs since the code which has __exit annotations
may already be gone when it is called.
WARNING: vmlinux.o(.init.text+0x1cc4a): Section mismatch in reference from the function init_QDIO() to the function .exit.text:qdio_setup_exit()
The function __init init_QDIO() references
a function __exit qdio_setup_exit().
This is often seen when error handling in the init function
uses functionality in the exit path.
The fix is often to remove the __exit annotation of
qdio_setup_exit() so it may be used outside an exit section.
WARNING: vmlinux.o(.init.text+0x1cc7a): Section mismatch in reference from the function init_QDIO() to the function .exit.text:qdio_remove_perf_stats()
The function __init init_QDIO() references
a function __exit qdio_remove_perf_stats().
This is often seen when error handling in the init function
uses functionality in the exit path.
The fix is often to remove the __exit annotation of
qdio_remove_perf_stats() so it may be used outside an exit section.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
kzalloc does not guarantee the required alignment of qdr to page size,
use get_zeroed_page instead.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Memory allocation for the quite huge idset changed from
kzalloc to vmalloc.
Signed-off-by: Michael Ernst <mernst@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
For hiper socket devices this patch will economize the reallocation
of the tx skb data segment by allocating separate memory for the qdio
transport information (qeth header).
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
sclp_sync_wait wait synchronously for an sclp interrupt and disables
timer interrupts. However on the irq enter paths there is an extra
check if a timer interrupt would be due and calls the timer callback.
This would schedule softirqs in the wrong context.
So introduce local_tick_enable/disable which prevents this.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When z/VM provides two virtual devices (minidisks) that reside on the
same real device, both will receive the configuration data from the
real device and thus get the same uid. To fix this problem, z/VM
provides an additional configuration data record that allows to
distinguish between minidisks.
z/VM APAR VM64273 needs be installed so this fix has an effect.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
drivers/mtd/nand/nandsim.c: In function 'divide':
drivers/mtd/nand/nandsim.c:462: error: implicit declaration of function 'do_div'
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Clean up and simplify the device initialization function:
* Degrade error messages to warnings - what they really are.
* Stop warning about VxI mode, we don't really care.
* Drop comment about lack of limit initialization - that's the standard
way, all hardware monitoring drivers do that.
* Only read the configuration register once.
* Only write back to the configuration register if needed.
* Don't attempt to clear the lock bit, it locks itself to 1.
* Move the function to before it's called, so that we no longer need to
forware declare it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Misc cleanups to the lm85 hardware monitoring driver:
* Mark constant arrays as const.
* Remove useless masks.
* Have lm85_write_value return void - nobody is checking the returned
value anyway and in some cases it was plain wrong.
* Remove useless initializations.
* Rename new_client to client in lm85_detect.
* Replace cascaded if/else with a switch/case in lm85_detect.
* Group similar loops in lm85_update_device.
* Remove legacy comments.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Juerg Haefliger <juergh at gmail.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
In set_pwm_auto_pwm_minctl, we write cached register bits back to the
chip. This is a bad idea as we have no guarantee that the cache is
up-to-date. Better read a fresh register value from the chip, it's
safer and in fact it is also more simple.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Juerg Haefliger <juergh at gmail.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Drop a lot of useless register defines, conversion macros, data structure
members and update code. All these register values were read from the
device but nothing is done out of them, so this is all dead code in
practice.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Juerg Haefliger <juergh at gmail.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Fix most style issues reported by checkpatch, including:
* Trailing, missing and extra whitespace
* Extra parentheses, curly braces and semi-colons
* Broken indentation
* Lines too long
I verified that the generated code is the same before and after
these changes.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Juerg Haefliger <juergh at gmail.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
More LM75 updates:
- Teach the LM75 driver to use new-style driver binding:
* Create a second driver struct, using new-style driver binding
methods cribbed from the legacy code.
* Add a MODULE_DEVICE_TABLE (for "newER-style binding")
* The legacy probe logic delegates its work to this new code.
* The legacy driver now uses the name "lm75_legacy".
- More careful initialization. Chips are put into 9-bit mode so
the current interconversion routines will never fail.
- Save the original chip configuration, and restore it on exit.
(Among other things, this normally turns off the mode where
the chip is constantly sampling ... and thus saves power.)
So the new-style code should catch all chips that boards declare,
while the legacy code catches others. This particular coexistence
strategy may need some work yet ... legacy modes might best be set
up explicitly by some tool not unlike "sensors-detect". (Or else
completely eradicated...)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Minor cleanup and reorg of the lm75 code.
- Kconfig provides a larger list of lm75-compatible chips
- A top comment now says what the driver does (!) ... as in, just
what sort of sensor is this??
- Section comments now delineate the various sections of the driver:
hwmon attributes, driver binding, register access, module glue.
One driver binding function moved out of the attribute section,
as did the driver struct itself.
- Minor tweaks to legacy probe logic: correct a comment, and
remove a pointless variable.
- Whitespace, linelength, and comment fixes.
This patch should include no functional changes. It's preparation
for adding new-style (driver model) I2C driver binding.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
All the *_MAX_ADDR defines are never used, so remove them. The number
of registers of each type is already expressed by the *_COUNT defines.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
This patch fixes a voltage scaling issue for the sch311x device.
Signed-Off-By: Juerg Haefliger <juergh at gmail.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
This patch adds a module load parameter to enable probing of
non-standard LPC addresses 0x162e and 0x164e when scanning for supported
ISA chips.
Signed-Off-By: Juerg Haefliger <juergh at gmail.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
This patch gets rid of a couple of macros previously used for sysfs attribute
generation and manipulation. This makes the source a little bigger but a lot
more readable and maintainable. It also fixes an issue with pwm5 & pwm6
attributes not being created read-only initially.
Signed-Off-By: Juerg Haefliger <juergh at gmail.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
When rescheduling a bio in raid10, we wake up
the md thread, but if the array is frozen, this
will have no effect. This causes the array to
remain frozen for eternity. We add a wake_up
to allow the array to de-freeze. This code is
nearly identical to the raid1 code, which has
this fix already.
Signed-off-by: Arthur Jones <ajones@riverbed.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When support for multiple TX queues were added, the
netif_tx_lock() routines we converted to iterate over
all TX queues and grab each queue's spinlock.
This causes heartburn for lockdep and it's not a healthy
thing to do with lots of TX queues anyways.
So modify this to use a top-level lock and a "frozen"
state for the individual TX queues.
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate and free everyting outside of the locked section.
Spotted-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Fixed-by: Seguier Regis <rseguier@e-teleport.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
It should help people fix the bugs in my code :o)
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The device id for Am29DL800BB in jedec_probe.c is wrong.
Reference: http://www.spansion.com/datasheets/21519c4.pdf
I discovered this while working with u-boot.
The u-boot folks mentioned Linux as an upstream reference, thought I'd
post a heads-up here too.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
- Add support for the RDC 1010 variant
- Rework the core library to have a read_id method. This allows the hacky
bits of it821x to go and prepares us for pata_hd
- Switch from WARN to BUG in ata_id_string as it will reboot if you get
it wrong so WARN won't be seen
- Allow the issue of command 0xFC on the 821x. This is needed to query
rebuild status.
- Tidy up printk formatting
- Do more ident rewriting on RAID volumes to handle firmware provided
ident data which is rather wonky
- Report the firmware revision and device layout in RAID mode
- Don't try and disable raid on the 8211 or RDC - they don't have the
relevant bits
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Subsys 106b:00a3 also is the weird apple ich8m which chokes when the
latter two ports are accessed, add it. Reported by Felipe Sere.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Felipe Sere <dodofxp@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix a potential memory leak when ata_init() encounters an error.
Signed-off-by: Elias Oltmanns <eo@nebensachen.de>
Cc: Tejun Heo <tj@kernel.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Global and per-LLD ATAPI disable checks were done in the command issue
path probably because it was left out during EH conversion. On
affected machines, this can cause lots of warning messages. Move them
to where they belong - the probing path.
Reported by Chunbo Luo.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Chunbo Luo <chunbo.luo@windriver.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add flag VIA_SATA_PATA for vx800, VX800 uses the same
chipset(0x0581/0x5324) as CX700, which has 1 PATA channel(Master/Slave)
and 1 SATA channel(Master/Slave) Add function <via_ata_tf_load>. This is
to fix the internal bug of VIA chipsets, which will reset the device
register after changing the IEN bit in CTL register
Signed-off-by: Joseph Chan <josephchan@via.com.tw>
Cc: Tejun Heo <tj@kernel.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The ali_init_one() function does a search for an isa_bridge,
but then fails to release it if the revision information was
not correctly found.
the problem comes from:
isa_bridge = pci_get_device(...);
if (isa_bridge && ...) {
pci_dev_put(isa_bridge);
}
where the pci_dev_put() is never called if isa_bridge
was valid but the extra checks on the chip-revision
fail to match.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is necessary to set the dongle type on the nsc driver in order to get
it to work correctly. Thinkpads all appear to use dongle type 9. This
patch defaults nsc devices with an IBM PnP descriptor to use type 9.
Signed-off-by: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Ben Collins <ben.collins@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
