Make sure the controller has no pending commands and ready for command
before issuing SRST.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement sil24_init_port which performs port initialization via
PORT_CS_INIT. To be used later by softreset and EH.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
SiI3124 might lose completion interrupt if completion interrupt occurs
shortly after SLOT_STAT register is read for the previous completion
interrupt if it is operating in PCI-X mode.
This currently doesn't trigger as libata never queues more than one
command, but it will with NCQ changes. This patch implements the
workaround - turning on WoC and explicitly clearing interrupt.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
All sil24 controllers share the same host flags except for NPORTS.
Consolidate them into SIL24_COMMON_FLAGS.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Move ata_set_mode() failure handling outside of ap->ops->set_mode if
clause such that it can handle ap->ops->set_mode failures after it's
updated.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Devices which consumed all their changes used to be disabled every
iteration. This causes unnecessary noise in the console output.
Disable once and leave alone.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
As waiting for some register bits to change seems to be a common
operation shared by some controllers, implement helper function
ata_wait_register(). This function also takes care of register write
flushing.
Note that the condition is inverted, the wait is over when the masked
value does NOT match @val. As we're waiting for bits to change, this
test is more powerful and allows the function to be used in more
places.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
sil24_softreset calculated timeout by adding ATA_TMOUT_BOOT * HZ to
jiffies; however, as ATA_TMOUT_BOOT is already in jiffies, multiplying
by HZ makes the value way off. Fix it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
@verbose was added to ata_reset_fn_t because AHCI complained during
probing if no device was attached to the port. However, muting
failure message isn't the correct approach. Reset methods are
responsible for detecting no device condition and finishing
successfully. Now that AHCI softreset is fixed, kill @verbose.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make setting CBL type responsibility of probeinit. This allows using
only ap->cbl == ATA_CBL_SATA test in all other parts. Without this,
ata_down_sata_spd_limit() doesn't work during probe reset.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild:
kconfig: fix typo in change count initialization
kconfig: recenter menuconfig
kconfig: revert conf behaviour change
kconfig: fix default value for choice input
kbuild: fix NULL dereference in scripts/mod/modpost.c
kbuild: fix mode of checkstack.pl and other files.
kbuild: rebuild initramfs if content of initramfs changes
kbuild: properly pass options to hostcc when doing make O=..
kbuild: modules_install for external modules must not remove existing modules
kbuild: fix make dir/
ver_linux: don't print reiser4progs version if none found
kbuild: mips: fix sed regexp to generate asm-offset.h
kbuild: fix building single targets with make O=.. single-target
kbuild: use relative path to -I
kbuild: fix unneeded rebuilds in drivers/net/chelsio after moving source tree
kbuild: fix unneeded rebuilds in drivers/media/video after moving source tree
kbuild: fix garbled text in modules.txt
Since the arrays are declared as in_urbs[N_IN_URB]
and out_urbs[N_OUT_URB], both for loops go one
over the end of the array. This fixes coverity id #555.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-Off-By: Matthias Urlichs <smurf@smurf.noris.de>
Signed-Off-By: Linus Torvalds <torvalds@osdl.org>
Since the visual STATIC_PSEUDOCOLOR has a read-only colormap, use logos
with 16 colors only since these logos use the console palette. This has a
higher likelihood that the logo will display correctly.
Signed-of-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Bugzilla Bug 6299:
A pixel size of 8 bits produces wrong logo colors in x86_64.
The driver has 2 methods for setting the color map, using the protected
mode interface provided by the video BIOS and directly writing to the VGA
registers. The former is not supported in x86_64 and the latter is enabled
only in i386.
Fix by enabling the latter method in x86_64 only if supported by the BIOS.
If both methods are unsupported, change the visual of vesafb to
STATIC_PSEUDOCOLOR.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Heaps of build errors - disable it to keep sparc32 allmodconfig happy.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix an obvious of-by-one error spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
CRC_CCITT is an internal helper function that should be select'ed.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix a memory leak spotted by the Coverity checker if
(!try_module_get(owner)).
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- make the needlessly global gigaset_get_cs_by_tty() static
- remove the unused EXPORT_SYMBOL_GPL(gigaset_debugdrivers)
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With Hansjoerg Lipp <hjlipp@web.de>
Replace some atomic_t variables in the Gigaset drivers by non-atomic ones,
using spinlocks instead to assure atomicity, as proposed in discussions on the
linux-kernel mailing list.
Signed-off-by: Hansjoerg Lipp <hjlipp@web.de>
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With Hansjoerg Lipp <hjlipp@web.de>
Remove four unnecessary forward function declarations and an obsolete E-mail
address from the Siemens Gigaset drivers.
Signed-off-by: Hansjoerg Lipp <hjlipp@web.de>
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With Hansjoerg Lipp <hjlipp@web.de>
Remove the private version of __skb_put() from the Siemens Gigaset drivers.
Signed-off-by: Hansjoerg Lipp <hjlipp@web.de>
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With Hansjoerg Lipp <hjlipp@web.de>
Convert the semaphores used by the Gigaset drivers to mutexes.
Signed-off-by: Hansjoerg Lipp <hjlipp@web.de>
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With Hansjoerg Lipp <hjlipp@web.de>
Eliminate the from_user argument from a debugging function, thus easing the
job of sparse.
Signed-off-by: Hansjoerg Lipp <hjlipp@web.de>
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With Hansjoerg Lipp <hjlipp@web.de>
Uninline a function which was slightly too big to warrant inlining.
Signed-off-by: Hansjoerg Lipp <hjlipp@web.de>
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With Hansjoerg Lipp <hjlipp@web.de>
Remove the IFNULL debugging macros from the Gigaset drivers.
Signed-off-by: Hansjoerg Lipp <hjlipp@web.de>
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With Hansjoerg Lipp <hjlipp@web.de>
Correct the way the Gigaset drivers create their sysfs entries.
Signed-off-by: Hansjoerg Lipp <hjlipp@web.de>
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With Hansjoerg Lipp <hjlipp@web.de>
Improve error reporting of the Gigaset drivers, by using the
dev_err/dev_warn/dev_info macros from device.h instead of err/warn/info from
usb.h whereever possible.
Also rename the private dbg macro to gig_dbg in order to avoid confusion with
the macro of the same name in usb.h.
Signed-off-by: Hansjoerg Lipp <hjlipp@web.de>
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With Hansjoerg Lipp <hjlipp@web.de>
Correct timer usage in the Gigaset drivers to take advantage of the existing
setup_timer() function, and use milliseconds as unit.
Signed-off-by: Hansjoerg Lipp <hjlipp@web.de>
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With Hansjoerg Lipp <hjlipp@web.de>
Remove the restriction to build the Gigaset drivers as modules only.
Signed-off-by: Hansjoerg Lipp <hjlipp@web.de>
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With Hansjoerg Lipp <hjlipp@web.de>
Source code formatting cleanups for the Siemens Gigaset drivers, such as line
length, comments, removal of unused declarations, and typo corrections. It
does not introduce any functional changes.
Signed-off-by: Hansjoerg Lipp <hjlipp@web.de>
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch updates VR4100 series RTC driver.
* This driver supports new RTC subsystem.
* Simple set time/read time test worked fine.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move the "24hr: yes" proc output from drivers to rtc proc code. This is
required because the time value in the proc output is always in 24hr mode
regardless of the driver.
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Tejun Heo
Jeff Garzik
Linus Torvalds
Matthias Urlichs
Antonino A. Daplas
Andrew Morton
Adrian Bunk
Tilman Schmidt
Alessandro Zummo
Yoichi Yuasa