The driver's ide_dma_test_irq() method was reading the MRDMODE register even on
PCI0643/6 where it was write-only -- fix this by always reading the "backward-
compatible" interrupt bits, renaming dma_alt_stat to irq_stat as the interrupt
status bits are not coupled to DMA.
In addition, wrong interrupt bit was tested/cleared for the primary channel --
it's bit 2 in all the chip specs and the driver used bit 1... :-/
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix the multiword DMA and drop the single-word DMA support (which nobody will
miss, I think). In order to do it, a number of changes was necessary:
- rename program_drive_counts() to program_cycle_times(), pass to it cycle's
total/active times instead of the clock counts, and convert them into the
active/recovery clocks there instead of cmd64x_tune_pio() -- this causes
quantize_timing() to also move;
- contrarywise, move all the code handling the address setup timing into
cmd64x_tune_pio(), so that setting MWDMA mode wouldn't change address setup;
- remove from the speedproc() method the bogus code pretending to set the DMA
timings by twiddling bits in the BMIDE status register, handle setting MWDMA
by just calling program_cycle_times(); while at it, improve the style of that
whole switch statement;
- stop fiddling with the DMA capable bits in the speedproc() method -- they do
not enable DMA, and are properly dealt with by the dma_host_{on,off} methods;
- don't set hwif->swdma_mask in the init_hwif() method anymore.
In addition to those changes, do the following:
- in cmd64x_tune_pio(), when writing to ARTTIM23 register preserve the interrupt
status bit, eliminate local_irq_{save|restore}() around this code as there's
*no* actual race with the interrupt handler, and move cmdprintk() to a more
fitting place -- after ide_get_best_pio_mode() call;
- make {arttim|drwtim}_regs arrays single-dimensional, indexed with drive->dn;
- rename {setup|recovery}_counts[] into more fitting {setup|recovery}_values[];
- in the speedproc() method, get rid of the duplicate reads/writes from/to the
UDIDETCRx registers and of the extra variable used to store the transfer mode
value after filtering, use another method of determining master/slave drive,
and cleanup useless parens;
- beautify cmdprintk() output here and there.
While at it, remove meaningless comment about the driver being used only on
UltraSPARC and long non-relevant RCS tag. :-)
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fold the now equivalent code in the ide_dma_check() method into a mere call to
ide_use_dma(). Make config_for_dma() return non-zero if DMA mode has been set
and call it from the ide_dma_check() method instead of ide_dma_on().
Defer writing the DMA timings to the chip registers until DMA is really turned
on (and do not enable IORDY for DMA).
Remove unneeded code from the init_hwif() method, improve its overall looks.
Rename the dma_start(), ide_dma_check(), and ide_dma_lostirq() methods, and
also use more proper hwif->dma_command, fix printk() and comment in the latter
one as well. While at it, cleanup style in several places.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Get rid of the 'pio_speed' member of 'ide_drive_t' that was only used by this
driver by storing the PIO mode timings in the 'drive_data' instead -- this
allows us to greatly simplify the process of "reloading" of the chip's timing
register and do it right in sl82c150_dma_off_quietly() and to get rid of two
extra arguments to config_for_pio() -- which got renamed to sl82c105_tune_pio()
and now returns a PIO mode selected, with ide_config_drive_speed() call moved
into the tuneproc() method, now called sl82c105_tune_drive() with the code to
set drive's 'io_32bit' and 'unmask' flags in its turn moved to its proper place
in the init_hwif() method.
Also, while at it, rename get_timing_sl82c105() into get_pio_timings() and get
rid of the code in it clamping cycle counts to 32 which was both incorrect and
never executed anyway...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
These are all the remaining instances of get_property. Simple rename of
get_property to of_get_property.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The subsystem rwsem is not used by the driver core at all, so the use of
it in the ide-proc code of it doesn't make any sense. Perhaps a local
lock might be needed, but I do not really think so.
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: linux ide <linux-ide@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ide_hwif_to_major[] has only 10 entries as there are 10 major numbers
reserved for IDE (if somebody needs more it shouldn't be hard to fix).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The driver crashes the kernel on HPT302N chips due to the missing initializer
for 'hpt302n.settings' having been unfortunately overlooked so far. :-<
Much thanks to Mike Mattie for pin-pointing the reason of crash.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add PCI ID for a newer variant of cardbus CF/IDE adapter card.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add "optical" to sysfs "media" attribute as already in /proc
Signed-off-by: Danny Kukawka <dkukawka@suse.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
I get the following error messages when trying to open a CD device
(specifically, the Teac CD-ROM CD-224E) that has no media present:
hda: packet command error: status=3D0x51 { DriveReady SeekComplete Error }
hda: packet command error: error=3D0x54 { AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
This happens when a "start stop unit" command (0x1b 0 0 0 3 0 0 0 0 0)
is sent to the drive to try to close the CD-ROM tray, but this drive
doesn't have that capability (it's a slim portable-type CD-ROM), so it
reports sense key 5 (illegal request) with asc/ascq 24/0. This is
exactly how SFF8090i says it should respond.
But ide-cd.c (in cdrom_decode_status() ) just sees sense key 5 and spews
out an error. It then goes on to request sense data, and
cdrom_log_sense() understands this error and doesn't log it.
The patch, for kernel 2.6.20.4, suppresses this error message.
Signed-off-by: Stuart Hayes <stuart_hayes@dell.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
It is possible for the timer expiry function to run even though the
request has already been handled: ide_timer_expiry() only checks that
the handler is not NULL, but it is possible that we have handled a
request (thus clearing the handler) and then started a new request
(thus starting the timer again, and setting a handler).
A simple way to exhibit this is to set the DMA timeout to 1 jiffy and
run dd: The kernel will panic after a few minutes because
ide_timer_expiry() tries to add a timer when it's already active.
To fix this, we simply add a request generation count that gets
incremented at every interrupt, and check in ide_timer_expiry() that
we have not already handled a new interrupt before running the expiry
function.
Signed-off-by: Suleiman Souhlal <suleiman@google.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
IDE error recovery is using IDLE IMMEDIATE if the drive is busy or has DRQ set.
This violates the ATA spec (can only send IDLEÂ IMMEDIATE when drive is not
busy) and really hoses up some drives (modern drives will not be able to
recover using this error handling). The correct thing to do is issue a SRST
followed by a SET FEATURES command. This is what Western Digital recommends
for error recovery and what Western Digital says Windows does.  It also does
not violate the ATA spec as far as I can tell.
Bart:
* port the patch over the current tree
* undo the recalibration code removal
* send SET FEATURES command after checking for good drive status
* don't check whether the current request is of REQ_TYPE_ATA_{CMD,TASK}
type because we need to send SET FEATURES before handling any requests
* some pre-ATA4 drives require INITIALIZE DEVICE PARAMETERS command before
other commands (except IDENTIFY) so send SET FEATURES only if there are
no pending drive->special requests
* update comments and patch description
* any bugs introduced by this patch are mine and not Suleiman's :-)
Signed-off-by: Suleiman Souhlal <suleiman@google.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
[ bart: the ressurection of 2 years old patch which slipped thru the cracks
(thanks to Sergei Shtylyov for finding it) ]
These is the patch to turn on pdc202xx_new for ATAPI DMA. When testing, it
works fine without the (request_bufflen % 256) workaround as needed in libata.
ide-scsi filters out (pc->request_transfer % 1024) and use PIO, so the pdc202xx
ATAPI DMA problem is avoid. Both ide-cd and ide-scsi won't hit the ATAPI DMA
problem on pdc202xx_new.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Since especially Serial ATA has it's own menu point now, I guess we can
change the description of the deprecated SATA driver as well, since the
new libATA subsystem is not configured through a SCSI low-level driver
anymore, but has it's own menu point.
From: Patrick Ringl <patrick_@freenet.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Since hwif->ide_dma_check and hwif->ide_dma_on never queue any commands
(ide_config_drive_speed() sets transfer mode using polling and has no error
recovery) we are safe with setting hwgroup->busy for the time while DMA
setting for a drive is changed (so it won't race against I/O commands in fly).
I audited briefly all ->ide_dma_check/->ide_dma_on/->tuneproc/->speedproc
implementations and they all look OK wrt to this change.
This patch finally allowed me to close kernel bugzilla bug #8169
(once again thanks to Patrick Horn for reporting the issue & testing patches).
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
"ide: fix drive side 80c cable check, take 2" patch from Tejun Heo (commit
fab59375b9) fixed 80c bit test (bit13 of word93)
but we also need to fix master/slave IDENTIFY order (slave device should be
probed first in order to make it release PDIAG- signal) and we should also
check for pre-ATA3 slave devices (which may not release PDIAG- signal).
[ Unfortunately the fact that IDE driver doesn't reset devices itself helps
only a bit as it seems that some BIOS-es reset ATA devices after programming
the chipset, some BIOS-es can be set to not probe/configure selected devices,
there may be no BIOS in case of add-on cards etc. ]
Since we are quite late in the release cycle and the required changes will
affect a lot of systems just revert the fix for now.
[ Please also see libata commit f31f0cc2f0. ]
Thanks goes out to Fernando Mitio Yamada for reporting the problem
and patiently testing patches.
Acked-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
All modern distributions have been setting these options to "y" for ages.
(additionally "n" cases have been obsoleted for few years). Therefore use
DMA by default and remove CONFIG_IDEDMA_{ICS,PCI}_AUTO (also remove no longer
needed CONFIG_IDEDMA_AUTO). This fixes DMA support for rare configurations
where CONFIG_IDEDMA_{ICS,PCI}_AUTO was set to "n" but "hdparm -d 1" was used
to enable DMA support and which were forced to PIO mode by "ide: don't allow
DMA to be enabled if CONFIG_IDEDMA_{ICS,PCI}_AUTO=n" patch. There is no
functionality loss because "ide=nodma" kernel option is still available.
Cc: Patrick Horn <phrh@yahoo.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Russell King <rmk+lkml@arm.linux.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
For CONFIG_IDEDMA_{ICS,PCI}_AUTO=n and/or "ide=nodma" option the host/device
are not programmed for DMA and it is also explicitly disabled by ide_set_dma()
(->ide_dma_check returns "-1"). However the code responsible for manually
enabling DMA ("hdparm -d 1") has a bug which results in DMA being erroneously
enabled - ide_set_dma() incorrectly passes "0" return value to set_using_dma().
This may work if BIOS/firmware configured the host/device for DMA and chipset
allows independent configuration of DMA/PIO modes but won't work after suspend
and is generally unsafe on many chipsets (possibly including data corruption
if the same registers are used for DMA/PIO timings).
This patch fixes kernel bugzilla bug #8169 (piix host driver fixes for
setting PIO mode exposed the problem described above). The side-effect of
the fix is that some rare configuration may be forced to PIO mode when DMA
mode was previously used - this is addressed by the next patch which removes
CONFIG_IDEDMA_{PCI,ICS}_AUTO config option completely.
Thanks goes out to Patrick Horn for reporting the issue, narrowing it down
to the specific commit and testing the fix. Also thanks to Sergei Shtylyov
for help in debugging the problem.
Cc: Patrick Horn <phrh@yahoo.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Russell King <rmk+lkml@arm.linux.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This patch fixes:
* the dependency of scc_pata on BLK_DEV_IDEDMA_PCI
* incorrect link to ide-core
* move scc_pata from ide/ppc to ide/pci
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Akira Iguchi <akira2.iguchi@toshiba.co.jp>
Cc: Al Viro <viro@ftp.linux.org.uk>,
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
When libata is configured, the device is configured such that SATA and
PATA ports live in separate functions with different programming
interfaces. pata_jmicron and ide jmicron drivers can drive only the
PATA part.
This patch makes jmicron match PCI class code such that it doesn't
attach itself to the SATA part preventing the proper ahci driver from
attaching.
This change is suggested by Bartlomiej.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: justin@jmicron.com
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The driver wrongly takes the address setup time into account when calculating
the PIO recovery time -- this leads to slight overclocking of the PIO modes 0
and 1 (so, the prayers failed to help, as usual :-). Rework the code to be
calculating recovery clock count as a difference between the total cycle count
and the active count (we don't need to calculate the recovery time itself since
it's not specified for the PIO modes 0 to 2, and for modes 3 and 4 this formula
gives enough recovery time anyway in the chip's supported PCI frequency range).
This patch has been inspired by reading the datasheets and looking at what the
libata driver does; it has been compile-tested only (as usual :-) but anyway,
the new code gives the same or longer recovery times than the old one...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
It's bool and it depends on IDE => should depend on IDE=y
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Legacy IDE VLB host drivers didn't check for "probe" options when compiled
as modules, which was obviously wrong as we don't want module to poke at
random I/O ports by simply loading it. Fix it by adding "probe" module param
to legacy IDE VLB host drivers.
v2:
* don't obsolete old "ide0=dtc2278/ht6560b/qd65xx/ali14xx/umc8672"
IDE driver options yet (per Alan Cox's request) and enhance documentation
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Remove
* "hdx=serialize"
* "idex=noautotune"
* "idex=autotune"
kernel params, they have been obsoleted for ages.
"idex=serialize", "hdx=noautotune" and "hdx=autotune" are still available
so there is no funcionality loss caused by this patch.
v2:
* fix CONFIG_BLK_DEV_4DRIVES=y build broken by version 1 of the patch
[ /me wearing brown paper bag ]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
On Tuesday 27 February 2007, Akira Iguchi wrote:
>
> But since I sent the first patch, I found a bug for checking DMA IRQ status.
> (http://www.spinics.net/lists/linux-ide/msg06903.html)
> Then I sent the fixed patch for libata only. So my drivers/ide patch
> still has same bug and I want to fix it, too.
>
> The following patch fixes this bug. Please apply this patch.
From: Akira Iguchi <akira2.iguchi@toshiba.co.jp>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Revised DRAC4 warning as Jeff suggested, this one includes more info
about why the problem occurs
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix breakage added in the IDE devel tree.
Add header, then fix
drivers/ide/ppc/pmac.c: In function `pmac_ide_setup_dma':
drivers/ide/ppc/pmac.c:2044: warning: assignment from incompatible pointer type
drivers/ide/ppc/pmac.c: In function `pmac_ide_dma_host_on':
drivers/ide/ppc/pmac.c:1989: warning: control reaches end of non-void function
include/linux/pci.h: In function `pmac_ide_init':
drivers/ide/ppc/pmac.c:1563: warning: ignoring return value of `pci_register_driver', declared with attribute warn_unused_result
Then add some apparently-long-missing error handling.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add CFA devices from I-O Data, Mitsubishi and Viking. Add SanDisk comment.
Signed-off-by: Magnus Damm <damm@opensource.se>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The function ide_get_best_pio_mode() fails to return the correct IORDY setting
for the explicitly specified modes -- fix this along with the heading comment,
and also remove the long commented out code.
Also, while at it, correct the misliading comment about the PIO cycle time in
<linux/ide.h> -- it actually consists of only the active and recovery periods,
with only some chips also including the address setup time into equation...
[ bart: sl82c105 seems to be currently the only driver affected by this fix ]
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The tuneproc() method in both these drivers failed to set the drive's own speed.
Fix this by renaming the function and "wrapping around it" the new tuneproc()
method. Switch back to calling tuneproc() in the PIO fallback code.
While at it, also convert the rest of the PIO timing code into proper C. :-)
Has been kind of tested on SLC90E66. I'm too lazy to reboot my box and test
on ICH4... :-)
[ bart: I quickly tested it on ICH4. ]
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
eighty_ninty_three() had word 93 validitity check but not the 80c bit
test itself (bit 13). This increases the chance of incorrect wire
detection especially because host side cable detection is often
unreliable and we sometimes soley depend on drive side cable
detection. Fix it.
[ bart: fix off-by-1 bit name in the patch description ]
Signed-off-by: Tejun Heo <htejun@gmail.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The driver's tuneproc() method fails to set the drive's own speed -- fix this
by renaming the function to cmd64x_tune_pio(), making it return the mode set,
and "wrapping" the new tuneproc() method around it; while at it, also get rid
of the non-working prefetch control code (filtering out related argument values
in the "wrapper"), remove redundant PIO5 mode limitation, make cmdprintk() give
more sensible mode info, and remove mention about the obsolete /proc/ interface.
Get rid of the broken config_chipset_for_pio() which always tried to set PIO4,
switch to always auto-tuning PIO instead.
Oh, and add the missing PIO5 support to the speedproc() method while at it. :-)
Warning: compile tested only -- getting to the real hardware isn't that easy...
On Tuesday 06 February 2007 22:11, Mikael Pettersson <mikpe@it.uu.se> wrote:
>
> Worked fine on my SPARC Ultra5 with a CMD646 IDE controller.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The driver's tuneproc() method fails to set the drive's own speed -- fix this
by renaming the function to ali15x3_tune_pio() and "wrapping" the new tuneproc()
method around it and making it return the mode set, update the heading comment.
Also, setting PIO mode via the speedproc() method does not work due to passing
to the tuneproc() method's a mode number not biased by XFER_PIO_0 -- fix this
along with a typo in the heading comment...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial: (25 commits)
Documentation/kernel-docs.txt update.
arch/cris: typo in KERN_INFO
Storage class should be before const qualifier
kernel/printk.c: comment fix
update I/O sched Kconfig help texts - CFQ is now default, not AS.
Remove duplicate listing of Cris arch from README
kbuild: more doc. cleanups
doc: make doc. for maxcpus= more visible
drivers/net/eexpress.c: remove duplicate comment
add a help text for BLK_DEV_GENERIC
correct a dead URL in the IP_MULTICAST help text
fix the BAYCOM_SER_HDX help text
fix SCSI_SCAN_ASYNC help text
trivial documentation patch for platform.txt
Fix typos concerning hierarchy
Fix comment typo "spin_lock_irqrestore".
Fix misspellings of "agressive".
drivers/scsi/a100u2w.c: trivial typo patch
Correct trivial typo in log2.h.
Remove useless FIND_FIRST_BIT() macro from cardbus.c.
...
* since ide_hwif_t.ide_dma_host_on is called either when drive->using_dma == 1
or when return value is discarded make it void, also drop "ide_" prefix
* make __ide_dma_host_on() void and drop "__" prefix
v2:
* while at it rename atiixp_ide_dma_host_on() to atiixp_dma_host_on()
and sgiioc4_ide_dma_host_on() to sgiioc4_dma_host_on().
[ Noticed by Sergei Shtylyov <sshtylyov@ru.mvista.com>. ]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* since ide_hwif_t.ide_dma_{host_off,off_quietly} always return '0'
make these functions void and while at it drop "ide_" prefix
* fix comment for __ide_dma_off_quietly()
* make __ide_dma_{host_off,off_quietly,off}() void and drop "__" prefix
v2:
* while at it rename atiixp_ide_dma_host_off() to atiixp_dma_host_off(),
sgiioc4_ide_dma_{host_off,off_quietly}() to sgiioc4_dma_{host_off,off_quietly}()
and sl82c105_ide_dma_off_quietly() to sl82c105_dma_off_quietly()
[ Noticed by Sergei Shtylyov <sshtylyov@ru.mvista.com>. ]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* add ide_set_dma() helper and make ide_hwif_t.ide_dma_check return
-1 when DMA needs to be disabled (== need to call ->ide_dma_off_quietly)
0 when DMA needs to be enabled (== need to call ->ide_dma_on)
1 when DMA setting shouldn't be changed
* fix IDE code to use ide_set_dma() instead if using ->ide_dma_check directly
v2:
* updated for scc_pata
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
All users of ->mmio == 1 are gone so convert ->mmio into flag.
Noticed by Alan Cox.
v2:
* updated for scc_pata
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This results in smaller/faster/simpler code and allows future optimizations.
Also remove no longer needed ide[_mm]_{inl,outl}() and ide_hwif_t.{INL,OUTL}.
v2:
* updated for scc_pata
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* add ide_use_fast_pio() helper for use by host drivers
* add DMA capability and hwif->autodma checks to ide_use_dma()
- au1xxx-ide/it8213/it821x drivers didn't check for (id->capability & 1)
[ for the IT8211/2 in SMART mode this check shouldn't be made but since
in it821x_fixups() we set DMA bit explicitly:
if(strstr(id->model, "Integrated Technology Express")) {
/* In raid mode the ident block is slightly buggy
We need to set the bits so that the IDE layer knows
LBA28. LBA48 and DMA ar valid */
id->capability |= 3; /* LBA28, DMA */
we are better off using generic helper if we can ]
- ide-cris driver didn't set ->autodma
[ before the patch hwif->autodma was only checked in the chipset specific
hwif->ide_dma_check implementations, for ide-cris it is cris_dma_check()
function so there no behavior change here ]
v2:
* updated patch description (thanks to Alan Cox for the feedback)
v3:
* updated for scc_pata driver
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
In cmd64x, siimage and scc_pata drivers:
* don't set drive->init_speed as it should be already
set by successful execution of ide_set_xfer_rate()
* use hwif->speedproc functions directly
Above changes allows removal of EXPORT_SYMBOL_GPL(ide_set_xfer_rate).
v2:
* updated for scc_pata driver
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This field is no longer used by the core IDE code so fix ide-{disk,floppy}
drivers to keep openers count in the driver specific objects and remove
it from ide-{cd,scsi,tape} drivers (it was write-only).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* remove bogus comment for sis5513_config_xfer_rate()
* there is no need to call config_drive_art_rwp() because
it is called by config_art_rwp_pio()
* remove needless wrapper
* remove stale "TODO" comment
(IDE core should provide generic tuning code)
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* disable DMA masks if no_piix_dma is set and remove now
not needed no_piix_dma_check from piix_config_drive_for_dma()
* there is no need to read register 0x55 in init_hwif_piix()
* move cable detection code to piix_cable_detect()
* remove unreachable 82371MX code from init_hwif_piix()
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* remove redundant svwks_ide_dma_end() [ __ide_dma_end() is used by default ]
* remove init_dma_svwks() so the default ide_setup_dma() function is used
[ init_setup_csb6() takes care of not initializing disabled channels ]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* BUG() on unknown DMA mode in cs5530_config_dma()
* there is no need to call hwif->ide_dma_host_{off,on}() in
cs5530_config_dma() because hwif->ide_dma_host_{off,on}()
is called by hwif->ide_dma_off_{quietly,on}()
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
In drivers/ide/Kconfig BLK_DEV_TRM290 depends on
BLK_DEV_IDEDMA_PCI (on which is BLK_DEV_IDEDMA dependant on).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This is the patch (based on 2.6.19-rc4) for PATA controller of
Toshiba Cell reference set(Celleb). The reference set consists
of Cell, 512MB memory, Super Companion Chip(SCC) and some
peripherals such as HDD, GbE, etc. You can see brief explanation
and picture of Cell reference set at following URLs.
http://www.toshiba.co.jp/about/press/2005_09/pr2001.htmhttp://cell-industries.com/toshiba_announces.php
We use a drivers/ide driver because its design is more suitable for
SCC IDE controller than libata driver. Since SCC supports only 32bit
read/write, we must override many callbacks of ata_port_operations
by modifying generic helpers. Each time the libata common code is
updated, we must update those modified helpers. It is very hard for us.
But we will try to implement the libata driver as needed.
Signed-off-by: Kou Ishizaki <kou.ishizaki at toshiba.co.jp>
Signed-off-by: Akira Iguchi <akira2.iguchi at toshiba.co.jp>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix a number of issues with the DMA support code:
- driver claims support for all SW/MW DMA modes while supporting only MWDMA2;
- ide_dma_check() method tries to enable DMA on the "known good" drives which
don't support MWDMA2;
- ide_dma_on() method upon failure to set drive to MWDMA2 re-tunes already
tuned PIO mode and calls ide_dma_off() method instead of returning error;
- ide_dma_off() method sets drive->current_speed while it doesn't actually
change (only the PIO timings are re-loaded into the chip's registers);
- init_hwif() method forcibly sets/resets both "drive DMA capable" bits while
this is properly handled by ide_dma_{on,off}() methods being called later...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix the driver's tuneproc() method to always set the PIO mode requested and not
pick the best possible one, rename it to pdc202xx_tune_drive(), and change the
calls to it accordingly; remove the preceding comment which has nothing to do
with the code.
Sergei Shtylyov wrote:
> The tuneproc() method should take arg 255 for auto-selecting the best PIO
> mode, not 5 as it did here + this driver's method always auto-selected instead
> of setting the mode it's been told to -- issue typical to drivers/ide/...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix two typos found by SiI680A documentation check. They caused the taskfile
transfer overclocking:
- in PIO mode 1 as 0x2283 must be used for both data and taskfile transfers;
- in PIO mode 2 as data and taskfile timings are swapped when writing to the
MMIO regs.
Fix coding style and trailing whitespace in enclosing statements while at it...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
drivers/ide/pci/siimage.c | 59 ++++++++++++++++++++++------------------------
1 file changed, 29 insertions(+), 30 deletions(-)
patch 2/2:
Remove clearing bmdma status from cdrom_decode_status() since ATA devices
might need it as well.
(http://lkml.org/lkml/2006/12/4/201 and http://lkml.org/lkml/2006/11/15/94)
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: "Adam W. Hawks" <awhawks@us.ibm.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
patch 1/2 (revised):
- Fix drive->waiting_for_dma to work with CDB-intr devices.
- Do the dma status clearing in ide_intr() and add a new
hwif->ide_dma_clear_irq for Intel ICHx controllers.
Revised per Alan, Sergei and Bart's advice.
Patch against 2.6.20-rc6. Tested ok on my ICH4 and pdc20275 adapters.
Please review/apply, thanks.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: "Adam W. Hawks" <awhawks@us.ibm.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
A ZIP or similar with unformatted media will cause crashes when attempts
are made to read/write it in some cases. This is because bs_factor is
zero and we divide by it causing an oops.
As the size of a non-accessible/non-existant media is really a bit of a
zen question it doesn't matter if non-existant media is 512 bytes per
sector or zero. Setting it to 1 causes us to generate 512 bytes/sector
accesses and error properly.
Based on a fix found lurking in an ancient bugzilla entry since about 2004 (ugghhh)
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* atiixp: if DMA can't be used atiixp_config_drive_for_dma() should return 0,
atiixp_dma_check() will tune the correct PIO mode anyway
* jmicron: if DMA can't be used config_chipset_for_dma() should return 0,
micron_config_drive_for_dma() will tune the correct PIO mode anyway
config_jmicron_chipset_for_pio(drive, !speed) doesn't program
device transfer mode for speed != 0 (only wastes some CPU cycles
on ide_get_best_pio_mode() call) so remove it
* triflex: if DMA can't be used triflex_config_drive_for_dma() should return 0,
triflex_config_drive_xfer_rate() will tune correct PIO mode anyway
Above changes also fix (theoretical) issue when ->speedproc fails to set
device transfer mode (i.e. when ide_config_drive_speed() fails to program it)
but one of DMA transfer modes is already enabled on the device by the BIOS.
In such scenario ide_dma_enable() will incorrectly return true statement
and ->ide_dma_check will try to enable DMA on the device.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* remember to clear reg2 bits for the current device before setting mode
* remove no longer needed hpt34x_clear_chipset()
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
After Al Viro (finally) succeeded in removing the sched.h #include in module.h
recently, it makes sense again to remove other superfluous sched.h includes.
There are quite a lot of files which include it but don't actually need
anything defined in there. Presumably these includes were once needed for
macros that used to live in sched.h, but moved to other header files in the
course of cleaning it up.
To ease the pain, this time I did not fiddle with any header files and only
removed #includes from .c-files, which tend to cause less trouble.
Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha,
arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig,
allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all
configs in arch/arm/configs on arm. I also checked that no new warnings were
introduced by the patch (actually, some warnings are removed that were emitted
by unnecessarily included header files).
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Many struct file_operations in the kernel can be "const". Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data. In addition it'll catch accidental writes at compile time to
these shared resources.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bug: pnx8550 code creates directory but resets ->nlink to 1.
create_proc_entry() et al will correctly set ->nlink for you.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Corey Minyard <minyard@acm.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Greg KH <greg@kroah.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds the module name to all PCI drivers, if they are built into the
kernel or not. It will show up in /sys/modules/MODULE_NAME/drivers/
It also fixes up the IDE core, which was calling __pci_register_driver()
directly.
Cc: Kay Sievers <kay.sievers@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/ide/ide-acpi.c: In function 'ide_acpi_get_timing':
drivers/ide/ide-acpi.c:537: warning: format '%x' expects type 'unsigned int', but argument 4 has type 'long unsigned int'
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This patch implements ACPI integration for generic IDE devices.
The ACPI spec mandates that some methods are called during suspend and
resume. And consequently there most modern Laptops cannot resume
properly without it.
According to the spec, we should call '_GTM' (Get Timing) upon suspend
to store the current IDE adapter settings.
Upon resume we should call '_STM' (Set Timing) to initialize the
adapter with the stored settings; afterwards '_GTF' (Get Taskfile)
should be called which returns a buffer with some IDE initialisation
commands. Those commands should be passed to the drive.
There are two module params which control the behaviour of this patch:
'ide=noacpi'
Do not call any ACPI methods (Disables any ACPI method calls)
'ide=acpigtf'
Enable execution of _GTF methods upon resume.
Has no effect if 'ide=noacpi' is set.
'ide=acpionboot'
Enable execution of ACPI methods during boot.
This might be required on some machines if 'ide=acpigtf' is
selected as some machines modify the _GTF information
depending on the drive identification passed down with _STM.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
On Thursday 11 January 2007 23:17, Bartlomiej Zolnierkiewicz wrote:
>
> My working IDE tree (against Linus' tree) now resides here:
>
> http://kernel.org/pub/linux/kernel/people/bart/pata-2.6/patches/
Bart, here's a driver I've been keeping out-of-tree for the past couple
of years. This is for the Delking/Lexar/ASKA/etc.. 32-bit cardbus IDE
CompactFlash adapter card.
It's probably way out of sync with the latest driver model (??), but it
still builds/works. I'm not interested in doing much of a rewrite, other
than for libata someday, as I no longer use the card myself.
But lots of other people do seem to use it, so it might be nice to see it
"in-tree".
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* set ATAPI/IORDY/TIME bits correctly in it8213_tuneproc()
* fix UDMA/MWDMA/SWDMA masks in it8213_init_hwif()
* in it8213_tune_chipset() SWDMA2 mode should be used instead of MWDMA0
* backport various fixes from piix/slc90e66 drivers:
- in it8213_tuneproc() the highest possible PIO mode is PIO4 (not PIO5)
- clear ATAPI/IORDY/TIME bits before setting them also for slave device
- use ->speedproc in it8213_config_drive_for_dma()
- don't try to tune PIO in config_chipset_for_pio()
- simplify is_slave calculation in it8213_tuneproc()
- misc cleanups
* fix it8213_ratemask() and it8213_tuneproc() comments
* simplify it8213_init_hwif()
* remove init_chipset_it8213()
* add missing Copyrights and update MODULE_AUTHOR()
* CodingStyle cleanups
* remove dead code
v2:
* PCI_DEVICE_ID_ITE_8213 is only defined in -mm kernels,
so just use PCI Device ID (0x8213) directly
* fix ->ultra_mask incorrectly changed to 0x3f in v1 version of the patch
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This is the driver for the Toshiba TC86C001 GOKU-S PCI IDE controller,
completely reworked from the original brain-damaged Toshiba's 2.4 version.
This single channel UltraDMA/66 controller is very simple in programming,
yet Toshiba managed to plant many interesting bugs in it. The particularly
nasty "limitation 5" (as they call the errata) caused me to abuse the IDE
core in a possibly most interesting way so far. However, this is still
better than the #ifdef mess in drivers/ide/ide-io.c that the original
version included (well, it had much more mess)...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Alan Cox <alan@redhat.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fold check_in_drive_lists() into quirkproc() handler in both PDC202xx
drivers-- this function was never called with a list other than
pdc_quirk_drives and was a bad example of code overall...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Remove the following useless fragments from the driver:
- the ide_dma_lostirq() and ide_dma_timeout() handlers which boil down to just
printing the incoherent reset message and calling their default counterparts;
- check for non-NULL drive->id in the ide_dma_check() handler -- this is assumed
to be true by all other handlers (also, get rid of unnecessary nesting of the
conditional statements there);
- the comment before pdcnew_tune_drive() which has nothing to do with the code.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Synchronize with version 0.46 of the Intel PIIX/ICH driver:
- carry over Alan's and my own fixes in the tuneproc() method and my cleanups
both there and in the ratemask() method;
- SLC90E66 only supports MW DMA modes 1/2 and SW DMA mode 2 (just like Intel
chips), so don't claim support for other MW/SW DMA modes;
- don't check dor non-NULL drive->id in the ide_dma_check() method -- this is
assumed to be true in all other drivers;
- do some coding/formatting cleanups while at it...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix/cleanup the driver's tuneproc() and ratemask() methods:
- PPE, IE, and TIME bits need to be cleared beforehand for the slave drive as
well as master (Alan probably just forgot about it);
- this driver only supports PIO modes up to 4, so must pass the correct limit
to ide_get_best_pio_mode();
- use min_t() macro instead of min();
- simplify slave vs master drive evaluation;
- do come coding and formatting cleanups...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
According to the datasheet, Intel 82371MX (MPIIX) actually has only a
single IDE channel mapped to the primary or secondary ports depending on
the value of the bit 14 of the IDETIM register at PCI config. offset 0x6C
(the register at 0x6F which the driver refers to. doesn't exist). So,
disguise the controller as dual channel and set enablebits masks/values
such that only either primary or secondary channel is detected enabled.
Also, preclude the IDE probing code from reading PCI BARs, this controller
just doesn't have them (it's not the separate PCI function like the other
PCI controllers), it only decodes the legacy addresses.
[ Alan sayeth " MPIIX does not work with or without the change. It needs its
own different driver and not to use setup-pci. Huge job and since it works
well with libata who cares. Ditto the early PIIX chip." ]
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix minor coding mistake in the HPT36x PCI clock detection code noticed by
Bartlomiej Zolnierkiewicz -- it always reported 33 MHz due to the missing
'break' statements. This, however, most probably never mattered -- in fact, I
was thinking of removing the 25/40 MHz cases completely since HPT36x BIOSes
didn't seem to set any other value than 7 into the 'cmd_high_time' field, i.e.
supported only 33 MHz PCI.
Note that in the original driver there was another bug: 25 and 40 MHz cases
were interchanged. Since the 'cmd_high_time' field is in units of PCI clocks,
a lower clock count just *cannot* correspond to a higher frequency, i. e. it
should be 5 for 25 MHz PCI and 9 for 40 MHz PCI, not the other way around.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Finally, rework the driver init. code to correctly handle all the chip
variants HighPoint has created so far. This should cure the rest of the
timing issues in the driver (especially, on 66 MHz PCI) caused by the
HighPoint's habit of switching the base DPLL clock with every new revision
of the chips...
- switch to using the enumeration type to differ between the numerous chip
variants, matching PCI device/revision ID with the chip type early, at the
init_setup stage;
- extend the hpt_info structure to hold the DPLL and PCI clock frequencies,
stop duplicating it for each channel by storing the pointer in the pci_dev
structure: first, at the init_setup stage, point it to a static "template"
with only the chip type and its specific base DPLL frequency, the highest
supported DMA mode, and the chip settings table pointer filled, then, at
the init_chipset stage, allocate per-chip instance and fill it with the
rest of the necessary information;
- get rid of the constant thresholds in the HPT37x PCI clock detection code,
switch to calculating PCI clock frequency based on the chip's base DPLL
frequency;
- switch to using the DPLL clock and enable UltraATA/133 mode by default on
anything newer than HPT370/A;
- fold PCI clock detection and DPLL setup code into init_chipset_hpt366(),
unify the HPT36x/37x setup code and the speedproc handlers by joining the
register setting lists into the table indexed by the clock selected;
- add enablebits for all the chips to avoid touching disabled channels
(though the HighPoint BIOS seem to only disable the primary one on
HPT371/N);
- separate the UltraDMA and MWDMA masks there to avoid changing PIO timings
when setting an UltraDMA mode in hpt37x_tune_chipset().
This version has been tested on HPT370/302/371N.
Thanks to Alan for the inspiration. Hopefully, his libata driver will also
benefit from the work done on this "obsolete" driver...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Clean up DMA timeout handling for HPT370:
- hpt370_lostirq_timeout() cleared the DMA status which made __ide_dma_end()
called afterwards return the incorrect result, and the DMA engine was reset
both before and after stopping DMA while the HighPoint drivers only do it
after (which seems logical) -- fix this and also rename the function;
- get rid of the needless mutual recursion in hpt370_ide_dma_end() and
hpt370_ide_dma_timeout();
- get rid of hpt370_lostirq_timeout() since hwif->ide_dma_end() called from
the driver's interrupt handler later does all its work.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Continue with the driver rewrite:
- move the interrupt twiddling code from the speedproc handlers into the
init_hwif_hpt366 which allows to merge the two HPT37x speedproc handlers
into one;
- get rid of in init_hpt366 which solely consists of the duplicate code, then
fold init_hpt37x() into init_chipset_hpt366();
- fix hpt3xx_tune_drive() to always set the PIO mode requested, not the best
possible one, change hpt366_config_drive_xfer_rate() accordingly, simplify
it a bit;
- group all the DMA related code together init_hwif_hpt366(), and generally
clean up and beautify it.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Begin the real driver redesign. For the starters:
- cache the offset of the IDE channel's MISC. control registers which are used
throughout the driver in hwif->select_data;
- only touch the relevant MCR when detecting the cable type on HPT374's
function 1;
- make HPT36x's speedproc handler look the same way as HPT37x ones; fix the
PIO timing register mask for HPT37x.
- rename all the HPT3xx register related variables consistently; clean up the
whitespace.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Switch to using pci_get_slot() to get to the function 1 of HPT36x/374 chips --
there's no need for the driver itself to walk the list of the PCI devices, and
it also forgets to check the bus number of the device found.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
- Rework the driver setup code so that it prefixes the driver startup
messages with the real chip name.
- Print the measured f_CNT value and the DPLL setting for non-HPT3xx
chips as well.
- Claim the extra 240 bytes of I/O space for all chips, not only for
those having PCI device ID of 0x0004.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
- Rework hpt3xx_ratemask() and hpt3xx_ratefilter() so that the former
returns the max. mode computed at the load time and doesn't have to do
bad Ultra33 drive list lookups anymore; remove the duplicate code from
the latter function. Move the quirky drive list lookup into
hpt3xx_quirkproc() where it should have been from the start...
- Disable UltraATA/100 for HPT370 by default as the 33 MHz ATA clock
being used does not allow for it, and this *greatly* increases the
transfer speed.
- Save some space by using byte-wide fields in struct hpt_info; switch to
reading the 8-bit PCI revision ID reg. only, not the whole 32-bit reg.
- Start incrementing the driver version number with each patch (should
have been done from the first one posted).
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
a) cleanup_module() should be __exit
b) externs should match reality
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
jmicron module detects all JMB36x as JMB361 and PATA0 has wrong pin status
of XICBLID.
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
