Update the sh7724 INTC tables with force_enable support
to mask out pending unsupported SDHI interrupt sources.
Without this patch the kernel locks up due to a pending
SDHI interrupt that the tmio_mmc driver cannot handle.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Break out sh7723 div4 clocks for SIU and IRDA as
reparent / enable clocks. Similar to the SIU clock
patch for sh7722 by Guennadi.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Merge the SDHI vectors in the sh7724 INTC table
and update the SDHI platform data for Ecovec24,
KFR2R09 and MS7724SE.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Merge the SDHI vectors in the sh7723 INTC table
and update the SDHI platform data for AP325.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Merge the SDHI vectors in the sh7722 INTC table
and update the SDHI platform data for Migo-R.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This improves power management for the SIUA controller on sh7722. Similar
patches might be desired for other SIU-enabled SH platforms.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The old ctrl in/out routines are non-portable and unsuitable for
cross-platform use. While drivers/sh has already been sanitized, there
is still quite a lot of code that is not. This converts the arch/sh/ bits
over, which permits us to flag the routines as deprecated whilst still
building with -Werror for the architecture code, and to ensure that
future users are not added.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that cached_to_uncached works as advertized in 32-bit mode and we're
never going to be able to map < 16MB anyways, there's no need for the
special uncached section. Kill it off.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Implement .set_rate() for all SH "div4 clocks," .enable(), .disable(), and
.set_parent() for those, that support them. This allows, among other uses,
reparenting of SIU clocks to the external source, and enabling and
disabling of the IrDA clock on sh7722.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This rewrites the SH7786 clock framework support completely. It's
reworked to provide all of the DIV4 and MSTP function clocks. This brings
it in line with the current clock framework code and lets us drop SH7786
from the list of CPUs that require legacy CPG handling.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently the secondary CPU entry point is only aimed at 29bit phys mode,
causing it to point to a stray virtual address in 32bit mode. Fix it up
after consulting with our shiny new __in_29bit_mode().
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This is the next big chunk of hw_breakpoint support. This decouples
the SH-4A support from the core and moves it out in to its own stub,
following many of the conventions established with the perf events
layering.
In addition to extending SH-4A support to encapsulate the remainder
of the UBC channels, clock framework support for handling the UBC
interface clock is added as well, allowing for dynamic clock gating.
This also fixes up a regression introduced by the SIGTRAP handling that
broke the ksym_tracer, to the extent that the current support works well
with all of the ksym_tracer/ptrace/kgdb. The kprobes singlestep code will
follow in turn.
With this in place, the remaining UBC variants (SH-2A and SH-4) can now
be trivially plugged in.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch breaks out the sh4a scif serial port platform
data from a shared platform device to one platform
device per port. Also, add serial ports to the list of
early platform devices.
All sh4a except SuperH Mobile processors are modified by
this patch.
While at it, sh7757 gets early platform device support.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch breaks out the sh4a scif serial port platform
data from a shared platform device to one platform
device per port. Also, add serial ports to the list of
early platform devices.
Only sh4a SuperH Mobile processors are modified by this
patch.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add sh7724 code to save and restore CPG state during
R-standby. Only CPG registers IRDACLKCR and SPUCLKCR
require software save and restore.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Wanted by the SPU2 UIO driver, which really ought to be handling this
itself. Default enable it for now, until the driver gets a bit more
intelligent.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add sh7724 code to save and restore RWDT state during
R-standby. Without this patch the watchdog will generate
a reset shortly after resuming from R-standby.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Make use of the recently added notifier chains for sh7724
r-standby register save/restore handling. At this point
only the BSC and INTC are handled.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds in preliminary support for the SH-4A performance counters.
Presently only the first 2 counters are supported, as these are the ones
of the most interest to the perf tool and end users. Counter chaining is
not presently handled, so these are simply implemented as 32-bit
counters.
This also establishes a perf event support framework for other hardware
counters, which the existing SH-4 oprofile code will migrate over to as
the SH-4A support evolves.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SCIF2 and the FPU exceptions happen to share vector numbers, one in
EXPEVT and the other in INTEVT. This is a violation of the interface and
should have never made it in to silicon. On top of that, the demux hack
that was added for special dispatch is rather error prone, and introduces
more problems than it solves. Kill all of it off, and just refuse to deal
with SCIF2 outright.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
All of the secondary CPUs are forced in to light sleep mode, but we were
missing the same initialization for the boot CPU. This resulted in
inconsistent sleep modes depending on which CPU we were on, confusing the
idle loop when not polling.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
In the multi-evt conversion for the SH-X3 proto CPU, IRLs were dropped
down to a single unique masking source, which ended up blowing up on
ILSEL-based IRQs which have special semantics that otherwise confuse the
intc code. While this does result in intc spewing about not having a
unique masking source, we don't really care.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The Runtime PM patch for UIO driver implements coarse grained
dynamic power management for UIO devices. With that patch in
place we can get rid of the static clock configuration. Which
in turn makes it possible for cpuidle to enter deeper sleep.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This fixes up the clockevents broadcasting code as detailed in commit
ee348d5a1d ("[ARM] realview: fix broadcast
tick support"). This saves us from having to do strange ordering things
with the broadcast clockevent device, relying on the rating instead.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the FRQCRA.IFC divisor values for SH7724. Despite
not being initially documented, the / 3 mode is also support for the IFC
division.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch removes the unused MSTPCRn register definitions
from the SuperH Mobile code for sh7722, sh7723 and sh7724.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Convert the processor platform device setup
functions from __initcall() and sometimes
device_initcall() to arch_initcall().
This makes sure that the platform devices are
registered a bit earlier so the devices are
available when drivers register using initcall
levels earlier than device_initcall().
A good example is platform devices needed by
i2c-sh_mobile.c which registers a bit earlier
using subsys_initcall().
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Convert the m66592-udc driver to use the on_chip flag
from platform data to enable on chip behaviour instead
of relying on CONFIG_SUPERH_BUILT_IN_M66592 ugliness.
This makes the code cleaner and also allows us to support
both external and internal m66592 with the same kernel.
It also makes the Kconfig part more future proof since
we with this patch can add support for new processors
with on-chip m66592 without modifying the Kconfig.
The patch adds a m66592 header file for platform data
and ties in platform data to the existing m66592 devices.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Convert the r8a66597-hcd driver to use the on_chip flag
from platform data to enable on chip behaviour instead
of relying on CONFIG_SUPERH_ON_CHIP_R8A66597 ugliness.
This makes the code cleaner and also allows us to support
both external and internal r8a66597 with the same kernel.
It also makes the Kconfig part more future proof since
we with this patch can add support for new processors
with on-chip r8a66597 without modifying the Kconfig.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Extend the SuperH hwblk code to support more than one counter.
Contains ground work for the future Runtime PM implementation.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch contains the sh7722 specific hwblk implementation.
Hwblk ids are added to the processor specific header file,
module stop bits and areas are kept track of as hwblks,
clocks are converted to make use of the shared hwblk code.
Code to determine allowed sleep modes is also added.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SH7786 is roughly identical to SH-X3 proto SMP, though there are only 2
CPUs. This just wraps in to the existing SH-X3 SMP code with some minor
changes for SH7786, including wiring up the IPIs properly, enabling
IRQ_PER_CPU, and so forth.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm
Guennadi Liakhovetski
Paul Mundt
Nobuhiro Iwamatsu
Kuninori Morimoto
Magnus Damm
Yoshihiro Shimoda