MAX_HEADER does not include the ipv6 header length in it,
so we need to add it in explicitly.
With help from YOSHIFUJI Hideaki.
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/drzeus/mmc:
mmc: correct request error handling
mmc: Flush block queue when removing card
mmc: sdhci high speed support
mmc: Support for high speed SD cards
mmc: Fix mmc_delay() function
mmc: Add support for mmc v4 wide-bus modes
[PATCH] mmc: Add support for mmc v4 high speed mode
trivial change for mmc/Kconfig: MMC_PXA does not mean only PXA255
Make general code cleanups
Add MMC_CAP_{MULTIWRITE,BYTEBLOCK} flags
Platform device error handling cleanup
Move register definitions away from the header file
Change OMAP_MMC_{READ,WRITE} macros to use the host pointer
Replace base with virt_base and phys_base
mmc: constify mmc_host_ops vectors
mmc: remove kernel_thread()
This reverts commit 281ea49b0c,
which broke ACPI Interrupt source overrides that move
the SCI from one IRQ in PIC mode to another in IOAPIC mode.
If the SCI shared an interrupt line with another device,
this would result in a "irq 18: nobody cared" type failure.
http://bugzilla.kernel.org/show_bug.cgi?id=7601
Signed-off-by: Len Brown <len.brown@intel.com>
Most PHYs connect to an ethernet controller over a GMII or MII
interface. However, a growing number are connected over
different interfaces, such as RGMII or SGMII.
The ethernet driver will tell the PHY what type of connection it
is by setting it manually, or passing it in through phy_connect
(or phy_attach).
Changes include:
* Updates to documentation
* Updates to PHY Lib consumers
* Changes to PHY Lib to add interface support
* Some minor changes to whitespace in phy.h
* gianfar driver now detects interface and passes appropriate
value to PHY Lib
Signed-off-by: Andrew Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If transmit lock is contended on, then push return code back
and retry at higher level.
Bugfix: If buffer is reallocated because of lack of headroom
and the send is blocked, then drop packet. This is necessary
because caller would end up requeuing a freed skb.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Cleanup statistics management:
* Get rid of duplicate or unused statistics
* Convert high volume stats to per-cpu and 64 bit
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Using MSI can avoid sharing IRQ and associated overhead.
Tested on PCI-X.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Replace driver crc calculation with existing library.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Replace macro with function for updating RMON values
Cleanups:
* remove unused enum's
* Fix comment format
Signed-off-by: Stephen HEmminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add support for other versions of the 10G Chelsio boards.
This is basically a port of the vendor driver with the
TOE features removed.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
I noticed this driver (and several others) reinvent their own copy of the
existing CRC library. Don't have the hardware, but tested by extracting
code and comparing result.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If using Message Signaled Interrupts (MSI) then the IRQ will never
be shared. Don't call pci_disable_msi() unless using MSI.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
It is possible for the sky2 driver NAPI poll routine to be called with
IRQ's disabled if netpoll is trying to make space in the tx queue. This
is an obscure path, but if it happens, the kfree_skb needs to happen
via softirq. Calling kfree_skb with IRQ's disabled is a not allowed.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update workarounds for 88E803X based on the latest SysKonnect vendor
driver version (8.41). Tested on EC_U rev A1, only.
These up the receive performance.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add new PCI ID for DLink 560SX.
This from the latest SysKonnect vendor driver (version 8.41).
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If sky2 detects out of memory, or gets a bad frame, it reuses the same receive
buffer, but forgets to poke the hardware. This could lead to the receiver
getting stuck if there were lots of errors.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
I would rather fix Andy's problem by not clearing
multicast information on link down.
Also, add code to restore multicast state after ethtool phy reset.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This bit of old backwards compatibility cruft can be removed in 2.6.20.
If there is still an device that calls register_netdev()
with a zero or blank name, it will get -EINVAL from register_netdevice().
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
drivers/built-in.o: In function `netxen_nic_remove':
netxen_nic_main.c:(.text+0x31b4d): undefined reference to `pci_disable_msi'
netxen_nic_main.c:(.text+0x31b8e): undefined reference to `pci_release_regions'
drivers/built-in.o: In function `netxen_init_module':
netxen_nic_main.c:(.init.text+0x3f17): undefined reference to `pci_module_init'
make: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The chelsio driver can use __netif_rx_schedule_prep instead of it's own
test_and_set inline. Applies after the previous 4 patches.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Network devices need to be free'd with free_netdev() not kfree()
otherwise the kernel will panic if an application has /sys/class/net/ethX/value
open and reads it.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Complete removal of proc stuff from chelsio. The orignal driver had a debug
proc interface, but not all the code got removed.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Whitespace cleanups. Replace leading spaces with tabs and fix indentation
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The chelsio network driver has some extra ifdef's that got in because the
driver was originally based on code that worked on 2.4 as well as 2.6.
This patch removes the dead code.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Include of_platform header, and use
new of_[un]register_platform_driver() fns.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use NULL instead of 0 for pointers (cures sparse warnings).
drivers/net/sundance.c:1106:16: warning: Using plain integer as NULL pointer
drivers/net/sundance.c:1652:16: warning: Using plain integer as NULL pointer
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Amit S. Kale <amitkale@netxen.com>
netxen_nic_main.c | 3 ++-
1 files changed, 2 insertions(+), 1 deletion(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When scanning in debug mode, softmac is very chatty in that it puts
3 lines in the logs for each time it scans. This patch has only one
line containing all the information previously reported.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Al Viro