File drivers/leds/leds-lp55xx-common.c refuse to change led_current sysfs
attribute if value is higher than max_current specified in board file. By default
global C variables are zero, so changing always failed. This patch adding missing
max_current and setting it to max safe value 100 (10 mA).
It is unclear which commit exactly caused this regression as the lp5523
driver was broken and was hiding the platform data breakage. Now
the driver is fixed so this should be fixed as well.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Joerg Reisenweber <joerg@openmoko.org>
[tony@atomide.com: updated comments to describe regression]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since dra7 reuses the function 'omap5_realtime_timer_init' in
arch/arm/mach-omap2/board-generic.c as timer init function, it has to be
built for this SoC as well.
Signed-off-by: Simon Barth <Simon.Pe.Barth@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The wake-up interrupt bit is available on omap3/4/5 processors
unlike what we claim. Without fixing it we cannot use it on
omap3 and the system configured for wake-up events will just
hang on wake-up.
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Benoît Cousson <bcousson@baylibre.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
SoC family definitions at the moment are reactive to board needs
as a result, beagle-xm would matchup with ti,omap3 which invokes
omap3430_init_early instead of omap3630_init_early. Obviously, this is
the wrong behavior.
With clock node dts conversion, we get the following warnings before
system hangs as a result and 3630 based platforms fails to boot
(uart4 clocks are only present in OMAP3630 and not present in
OMAP3430):
...
omap_hwmod: uart4: cannot clk_get main_clk uart4_fck
omap_hwmod: uart4: cannot _init_clocks
WARNING: CPU: 0 PID: 1 at arch/arm/mach-omap2/omap_hwmod.c:2434
_init+0x6c/0x80()
omap_hwmod: uart4: couldn't init clocks
...
WARNING: CPU: 0 PID: 1 at arch/arm/mach-omap2/omap_hwmod.c:2126
_enable+0x254/0x280()
omap_hwmod: timer12: enabled state can only be entered from
initialized, idle, or disabled state
...
WARNING: CPU: 0 PID: 46 at arch/arm/mach-omap2/omap_hwmod.c:2224
_idle+0xd4/0xf8()
omap_hwmod: timer12: idle state can only be entered from enabled state
WARNING: CPU: 0 PID: 1 at arch/arm/mach-omap2/omap_hwmod.c:2126
_enable+0x254/0x280()
omap_hwmod: uart4: enabled state can only be entered from
initialized, idle, or disabled state
So, add specific compatiblity for 3630 to allow match for Beagle-XM
platform.
Signed-off-by: Nishanth Menon <nm@ti.com>
[tony@atomide.com: left out ti,omap343x, updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Corrected the functions spelling mistake in the OMAP4 SMP source file.
Signed-off-by: Anoop Thomas Mathew <atm@profoundis.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When CONFIG_ARM_LPAE=y the following build warning is generated:
arch/arm/mach-omap2/gpmc.c:1495:4: warning: format '%x' expects argument of type 'unsigned int', but argument 4 has type 'resource_size_t' [-Wformat]
According to Documentation/printk-formats.txt '%pa' can be used to properly
print 'resource_size_t'.
Reported-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In case of error, the function omap_device_alloc() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check
should be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like we still have the legacy clock alias name for
omap4 GPMC (General Purpose Memory Controller), so let's
fix it for the device tree naming. There's no need to keep
the legacy naming as omap4 is DT only nowadays.
Without this fix we get the following error while booting:
[ 0.440399] omap-gpmc 50000000.gpmc: error: clk_get
Reported-by: Olof Johansson <olof@lixom.net>
Cc: stable@vger.kernel.org # v3.11
Signed-off-by: Tony Lindgren <tony@atomide.com>
These are changes that arrived a little late before the merge window,
or had dependencies on previous branches.
Highlights:
- ux500: misc. cleanup, fixup I2C devices
- exynos: DT updates for RTC; PM updates
- at91: DT updates for NAND; new platforms added to generic defconfig
- sunxi: DT updates: cubieboard2, pinctrl driver, gated clocks
- highbank: LPAE fixes, select necessary ARM errata
- omap: PM fixes and improvements; OMAP5 mailbox support
- omap: basic support for new DRA7xx SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=NIZZ
-----END PGP SIGNATURE-----
Merge tag 'late-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late changes from Kevin Hilman:
"These are changes that arrived a little late before the merge window,
or had dependencies on previous branches.
Highlights:
- ux500: misc. cleanup, fixup I2C devices
- exynos: DT updates for RTC; PM updates
- at91: DT updates for NAND; new platforms added to generic defconfig
- sunxi: DT updates: cubieboard2, pinctrl driver, gated clocks
- highbank: LPAE fixes, select necessary ARM errata
- omap: PM fixes and improvements; OMAP5 mailbox support
- omap: basic support for new DRA7xx SoCs"
* tag 'late-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (60 commits)
ARM: dts: vexpress: Add CCI node to TC2 device-tree
ARM: EXYNOS: Skip C1 cpuidle state for exynos5440
ARM: EXYNOS: always enable PM domains support for EXYNOS4X12
ARM: highbank: clean-up some unused includes
ARM: sun7i: Enable the A20 clocks in the DTSI
ARM: sun6i: Enable clock support in the DTSI
ARM: sun5i: dt: Use the A10s gates in the DTSI
ARM: at91: at91_dt_defconfig: enable rm9200 support
ARM: dts: add ADC device tree node for exynos5420/5250
ARM: dts: Add RTC DT node to Exynos5420 SoC
ARM: dts: Update the "status" property of RTC DT node for Exynos5250 SoC
ARM: dts: Fix the RTC DT node name for Exynos5250
irqchip: mmp: avoid to include irqs head file
ARM: mmp: avoid to include head file in mach-mmp
irqchip: mmp: support irqchip
irqchip: move mmp irq driver
ARM: OMAP: AM33xx: clock: Add RNG clock data
ARM: OMAP: TI81XX: add always-on powerdomain for TI81XX
ARM: OMAP4: clock: Lock PLLs in the right sequence
ARM: OMAP: AM33XX: hwmod: Add hwmod data for debugSS
...
Pull crypto update from Herbert Xu:
"Here is the crypto update for 3.12:
- Added MODULE_SOFTDEP to allow pre-loading of modules.
- Reinstated crct10dif driver using the module softdep feature.
- Allow via rng driver to be auto-loaded.
- Split large input data when necessary in nx.
- Handle zero length messages correctly for GCM/XCBC in nx.
- Handle SHA-2 chunks bigger than block size properly in nx.
- Handle unaligned lengths in omap-aes.
- Added SHA384/SHA512 to omap-sham.
- Added OMAP5/AM43XX SHAM support.
- Added OMAP4 TRNG support.
- Misc fixes"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (66 commits)
Reinstate "crypto: crct10dif - Wrap crc_t10dif function all to use crypto transform framework"
hwrng: via - Add MODULE_DEVICE_TABLE
crypto: fcrypt - Fix bitoperation for compilation with clang
crypto: nx - fix SHA-2 for chunks bigger than block size
crypto: nx - fix GCM for zero length messages
crypto: nx - fix XCBC for zero length messages
crypto: nx - fix limits to sg lists for AES-CCM
crypto: nx - fix limits to sg lists for AES-XCBC
crypto: nx - fix limits to sg lists for AES-GCM
crypto: nx - fix limits to sg lists for AES-CTR
crypto: nx - fix limits to sg lists for AES-CBC
crypto: nx - fix limits to sg lists for AES-ECB
crypto: nx - add offset to nx_build_sg_lists()
padata - Register hotcpu notifier after initialization
padata - share code between CPU_ONLINE and CPU_DOWN_FAILED, same to CPU_DOWN_PREPARE and CPU_UP_CANCELED
hwrng: omap - reorder OMAP TRNG driver code
crypto: omap-sham - correct dma burst size
crypto: omap-sham - Enable Polling mode if DMA fails
crypto: tegra-aes - bitwise vs logical and
crypto: sahara - checking the wrong variable
...
This branch contains mostly additions and changes to platform enablement
and SoC-level drivers. Since there's sometimes a dependency on device-tree
changes, there's also a fair amount of those in this branch.
Pieces worth mentioning are:
- Mbus driver for Marvell platforms, allowing kernel configuration
and resource allocation of on-chip peripherals.
- Enablement of the mbus infrastructure from Marvell PCI-e drivers.
- Preparation of MSI support for Marvell platforms.
- Addition of new PCI-e host controller driver for Tegra platforms
- Some churn caused by sharing of macro names between i.MX 6Q and 6DL
platforms in the device tree sources and header files.
- Various suspend/PM updates for Tegra, including LP1 support.
- Versatile Express support for MCPM, part of big little support.
- Allwinner platform support for A20 and A31 SoCs (dual and quad Cortex-A7)
- OMAP2+ support for DRA7, a new Cortex-A15-based SoC.
The code that touches other architectures are patches moving
MSI arch-specific functions over to weak symbols and removal of
ARCH_SUPPORTS_MSI, acked by PCI maintainers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=fJ5x
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"This branch contains mostly additions and changes to platform
enablement and SoC-level drivers. Since there's sometimes a
dependency on device-tree changes, there's also a fair amount of
those in this branch.
Pieces worth mentioning are:
- Mbus driver for Marvell platforms, allowing kernel configuration
and resource allocation of on-chip peripherals.
- Enablement of the mbus infrastructure from Marvell PCI-e drivers.
- Preparation of MSI support for Marvell platforms.
- Addition of new PCI-e host controller driver for Tegra platforms
- Some churn caused by sharing of macro names between i.MX 6Q and 6DL
platforms in the device tree sources and header files.
- Various suspend/PM updates for Tegra, including LP1 support.
- Versatile Express support for MCPM, part of big little support.
- Allwinner platform support for A20 and A31 SoCs (dual and quad
Cortex-A7)
- OMAP2+ support for DRA7, a new Cortex-A15-based SoC.
The code that touches other architectures are patches moving MSI
arch-specific functions over to weak symbols and removal of
ARCH_SUPPORTS_MSI, acked by PCI maintainers"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (266 commits)
tegra-cpuidle: provide stub when !CONFIG_CPU_IDLE
PCI: tegra: replace devm_request_and_ioremap by devm_ioremap_resource
ARM: tegra: Drop ARCH_SUPPORTS_MSI and sort list
ARM: dts: vf610-twr: enable i2c0 device
ARM: dts: i.MX51: Add one more I2C2 pinmux entry
ARM: dts: i.MX51: Move pins configuration under "iomuxc" label
ARM: dtsi: imx6qdl-sabresd: Add USB OTG vbus pin to pinctrl_hog
ARM: dtsi: imx6qdl-sabresd: Add USB host 1 VBUS regulator
ARM: dts: imx27-phytec-phycore-som: Enable AUDMUX
ARM: dts: i.MX27: Disable AUDMUX in the template
ARM: dts: wandboard: Add support for SDIO bcm4329
ARM: i.MX5 clocks: Remove optional clock setup (CKIH1) from i.MX51 template
ARM: dts: imx53-qsb: Make USBH1 functional
ARM i.MX6Q: dts: Enable I2C1 with EEPROM and PMIC on Phytec phyFLEX-i.MX6 Ouad module
ARM i.MX6Q: dts: Enable SPI NOR flash on Phytec phyFLEX-i.MX6 Ouad module
ARM: dts: imx6qdl-sabresd: Add touchscreen support
ARM: imx: add ocram clock for imx53
ARM: dts: imx: ocram size is different between imx6q and imx6dl
ARM: dts: imx27-phytec-phycore-som: Fix regulator settings
ARM: dts: i.MX27: Remove clock name from CPU node
...
This branch contains code cleanups, moves and removals for 3.12.
There's a large number of various cleanups, and a nice net removal of
13500 lines of code.
Highlights worth mentioning are:
- A series of patches from Stephen Boyd removing the ARM local timer API.
- Move of Qualcomm MSM IOMMU code to drivers/iommu.
- Samsung PWM driver cleanups from Tomasz Figa, removing legacy PWM driver
and switching over to the drivers/pwm one.
- Removal of some unusued auto-generated headers for OMAP2+ (PRM/CM).
There's also a move of a header file out of include/linux/i2c/ to
platform_data, where it really belongs. It touches mostly ARM platform
code for include changes so we took it through our tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=1vE4
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This branch contains code cleanups, moves and removals for 3.12.
There's a large number of various cleanups, and a nice net removal of
13500 lines of code.
Highlights worth mentioning are:
- A series of patches from Stephen Boyd removing the ARM local timer
API.
- Move of Qualcomm MSM IOMMU code to drivers/iommu.
- Samsung PWM driver cleanups from Tomasz Figa, removing legacy PWM
driver and switching over to the drivers/pwm one.
- Removal of some unusued auto-generated headers for OMAP2+ (PRM/CM).
There's also a move of a header file out of include/linux/i2c/ to
platform_data, where it really belongs. It touches mostly ARM
platform code for include changes so we took it through our tree"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (83 commits)
ARM: OMAP2+: Add back the define for AM33XX_RST_GLOBAL_WARM_SW_MASK
gpio: (gpio-pca953x) move header to linux/platform_data/
arm: zynq: hotplug: Remove unreachable code
ARM: SAMSUNG: Remove unnecessary exynos4_default_sdhci*()
tegra: simplify use of devm_ioremap_resource
ARM: SAMSUNG: Remove plat/regs-timer.h header
ARM: SAMSUNG: Remove remaining uses of plat/regs-timer.h header
ARM: SAMSUNG: Remove pwm-clock infrastructure
ARM: SAMSUNG: Remove old PWM timer platform devices
pwm: Remove superseded pwm-samsung-legacy driver
ARM: SAMSUNG: Modify board files to use new PWM platform device
ARM: SAMSUNG: Rework private data handling in dev-backlight
pwm: Add new pwm-samsung driver
ARM: mach-mvebu: remove redundant DT parsing and validation
ARM: msm: Only compile io.c on platforms that use it
iommu/msm: Move mach includes to iommu directory
ARM: msm: Remove devices-iommu.c
ARM: msm: Move mach/board.h contents to common.h
ARM: msm: Migrate msm_timer to CLOCKSOURCE_OF_DECLARE
ARM: msm: Remove TMR and TMR0 static mappings
...
This branch contains a handful of fixes for various platforms that
weren't serious enough to be included in late 3.11-rc releases. Most of
them are for minor cleanups and cosmetic fixes.
There's also a bit of code removal here, one board file removal for
clps711x, and removal of some legacy device creation on OMAP2+.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=S4TX
-----END PGP SIGNATURE-----
Merge tag 'fixes-nc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC low-priority fixes from Olof Johansson:
"This branch contains a handful of fixes for various platforms that
weren't serious enough to be included in late 3.11-rc releases. Most
of them are for minor cleanups and cosmetic fixes.
There's also a bit of code removal here, one board file removal for
clps711x, and removal of some legacy device creation on OMAP2+"
* tag 'fixes-nc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (25 commits)
ARM: OMAP2: use 'int' instead of 'unsigned' for variable 'gpmc_irq_start'
ARM: OMAP2: remove useless variable 'ret'
ARM: OMAP: dma: fix error return code in omap_system_dma_probe()
ARM: OMAP2+: fix wrong address when loading PRM_FRAC_INCREMENTOR_DENUMERATOR_RELOAD
ARM: OMAP2+: am33xx-restart: trigger warm reset on omap2+ boards
ARM: OMAP2: Use a consistent AM33XX SoC option description
ARM: OMAP2+: Remove legacy device creation for McPDM and DMIC
ARM: clps711x: edb7211: Remove extra iotable_init() call
ARM: clps711x: autcpu12: Remove incorrect config checking
ARM: clps711x: Drop fortunet board support
ARM: clps711x: Remove the special name for the syscon driver
ARM: dts: Fix memory node in skeleton64.dtsi
ARM: Keystone: Convert device tree file to use IRQ defines
ARM: keystone: use #include to include skeleton.dtsi
ARM: keystone: Drop the un-necessary dsb from keystone_cpu_smc()
ARM: Keystone: No need to preserve r12 across smc call
ARM: keystone: remove redundant smp_init_cpus definition
ARM: keystone: drop useless HAVE_SCHED_CLOCK
ARM: dove: fix missing __init section of dove_mpp_gpio_mode
ARM: shmobile: armadillo800eva-reference: fix compiler warning
...
* Change the OMAP board files to use the new OMAP display drivers
* Remove all the old drivers, and the related auxiliary code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=Hj7U
-----END PGP SIGNATURE-----
Merge tag 'fbdev-3.12-omap-legacy-removal' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull OMAP specific fbdev changes from Tomi Valkeinen:
"I've got this pull request separate from the main fbdev pull request,
as this contains a bunch of OMAP board file changes and thus could
possibly be rejected in case of bad conflicts.
The removal of the old display drivers depend on the board file
changes, so Tony Lindgren suggested taking them together via fbdev
tree. These are in linux-next, and also Tony didn't see any conflicts
with any of the branches he had, so they should go in clean.
- Change the OMAP board files to use the new OMAP display drivers
- Remove all the old drivers, and the related auxiliary code"
* tag 'fbdev-3.12-omap-legacy-removal' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (35 commits)
OMAPDSS: rename omap_dss_device's 'device' field to 'dst'
OMAPDSS: rename omap_dss_device's 'output' to 'src'
OMAPDSS: DSS: remove legacy dss bus support
OMAPDSS: RFBI: remove code related to old panel model
OMAPDSS: VENC: remove code related to old panel model
OMAPDSS: SDI: remove code related to old panel model
OMAPDSS: DSI: remove code related to old panel model
OMAPDSS: HDMI: remove code related to old panel model
OMAPDSS: DPI: remove code related to old panel model
OMAPDSS: remove all old panel drivers
OMAPDSS: DPI: change regulator handling
OMAPDSS: SDI: change regulator handling
OMAPDSS: fix DPI and SDI device ids
OMAPDSS: remove omap_dss_device->channel field
OMAPDSS: RFBI: Mark RFBI as broken
ARM: OMAP2+: Remove old display drivers from omap2plus_defconfig
ARM: OMAP: AM3517EVM: use new display drivers
ARM: OMAP: Zoom: use new display drivers
ARM: OMAP: Pandora: use new display drivers
ARM: OMAP: OMAP3EVM: use new display drivers
...
up with PTR_ERR_OR_ZERO(), and replacing or fixing all the usages.
This has been sitting in linux-next for a whole cycle.
Thanks,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=LeaW
-----END PGP SIGNATURE-----
Merge tag 'PTR_RET-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull PTR_RET() removal patches from Rusty Russell:
"PTR_RET() is a weird name, and led to some confusing usage. We ended
up with PTR_ERR_OR_ZERO(), and replacing or fixing all the usages.
This has been sitting in linux-next for a whole cycle"
[ There are still some PTR_RET users scattered about, with some of them
possibly being new, but most of them existing in Rusty's tree too. We
have that
#define PTR_RET(p) PTR_ERR_OR_ZERO(p)
thing in <linux/err.h>, so they continue to work for now - Linus ]
* tag 'PTR_RET-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
GFS2: Replace PTR_RET with PTR_ERR_OR_ZERO
Btrfs: volume: Replace PTR_RET with PTR_ERR_OR_ZERO
drm/cma: Replace PTR_RET with PTR_ERR_OR_ZERO
sh_veu: Replace PTR_RET with PTR_ERR_OR_ZERO
dma-buf: Replace PTR_RET with PTR_ERR_OR_ZERO
drivers/rtc: Replace PTR_RET with PTR_ERR_OR_ZERO
mm/oom_kill: remove weird use of ERR_PTR()/PTR_ERR().
staging/zcache: don't use PTR_RET().
remoteproc: don't use PTR_RET().
pinctrl: don't use PTR_RET().
acpi: Replace weird use of PTR_RET.
s390: Replace weird use of PTR_RET.
PTR_RET is now PTR_ERR_OR_ZERO(): Replace most.
PTR_RET is now PTR_ERR_OR_ZERO
Here's the big USB driver pull request for 3.12-rc1
Lots of USB driver fixes and updates. Nothing major, just the normal
xhci, gadget, and other driver changes. Full details in the shortlog.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.21 (GNU/Linux)
iEYEABECAAYFAlIlJJ8ACgkQMUfUDdst+ymBAwCgg8czTAuwpCCK7H8LHnC2BsMj
dtUAnjDisrbw4qWSXaaA/sfgSZjKW5G4
=Tman
-----END PGP SIGNATURE-----
Merge tag 'usb-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patches from Greg KH:
"Here's the big USB driver pull request for 3.12-rc1
Lots of USB driver fixes and updates. Nothing major, just the normal
xhci, gadget, and other driver changes. Full details in the shortlog"
* tag 'usb-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (352 commits)
usbcore: fix incorrect type in assignment in descriptors_changed()
usbcore: compare and release one bos descriptor in usb_reset_and_verify_device()
ehci: remove debugging statement with ehci statistics in ehci_stop()
ehci: remove duplicate debug_async_open() prototype in ehci-dbg.c
ehci: enable debugging code when CONFIG_DYNAMIC_DEBUG is set
ehci: remove ehci_vdbg() verbose debugging statements
Documentation sysfs-bus-usb: Document which files are used by libusb
Documentation sysfs-bus-usb: Document the speed file used by libusb
Documentation sysfs-bus-usb: Move files with known users to stable
USB: fix build error when CONFIG_PM_SLEEP isn't enabled
usb: r8a66597-hcd: use platform_{get,set}_drvdata()
usb: phy-tegra-usb: use platform_{get,set}_drvdata()
usb: acm gadget: Null termintate strings table
dma: cppi41: off by one in desc_to_chan()
xhci: Fix warning introduced by disabling runtime PM.
dev-core: fix build break when DEBUG is enabled
USB: OHCI: Allow runtime PM without system sleep
usb: ohci-at91: remove unnecessary dev_set_drvdata()
usb: renesas_usbhs: use platform_{get,set}_drvdata()
usb: fotg210-udc: use platform_{get,set}_drvdata()
...
This is needed to prevent a build error with a patch queued for fixes
"ARM: OMAP2+: am33xx-restart: trigger warm reset on omap2+ boards".
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
parts the same way as for other omaps. This is still needed in
addition to device tree support for things like power management.
Via Paul Walmsley <paul@pwsan.com>:
This series adds basic TI DRA7xx PRCM and hwmod support.
Basic test logs are available here:
http://www.pwsan.com/omap/testlogs/dra7xx_prcm_devel_v3.12/20130823050445/
Note that DRA7xx could not be tested locally, since I don't have a board.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=c+8k
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.12/dra7xx-prcm' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into late/all
From Tony Lindgren:
Add basic support for devices on dra7xx by adding the PRCM and hwmod
parts the same way as for other omaps. This is still needed in
addition to device tree support for things like power management.
Via Paul Walmsley <paul@pwsan.com>:
This series adds basic TI DRA7xx PRCM and hwmod support.
Basic test logs are available here:
http://www.pwsan.com/omap/testlogs/dra7xx_prcm_devel_v3.12/20130823050445/
Note that DRA7xx could not be tested locally, since I don't have a board.
* tag 'omap-for-v3.12/dra7xx-prcm' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: DRA7: Enable PM framework initializations
ARM: OMAP: DRA7: hwmod: Create initial DRA7XX SoC data
ARM: OMAP: DRA7: Reuse the omap44xx_restart and fix the device instance
ARM: OMAP: DRA7: powerdomain: Handle missing vc/vp
ARM: OMAP: DRA7: powerdomain: Add DRA7XX data and update header
ARM: OMAP: DRA7: clockdomain: Add DRA7XX data and update header
ARM: OMAP: DRA7: PRCM: Add DRA7XX local MPU PRCM regsiters
ARM: OMAP: DRA7: CM: Add minimal regbit shifts
ARM: OMAP: DRA7: CM: Add DRA7XX register defines
ARM: OMAP: DRA7: PRM: Add DRA7XX register definitions
ARM: DRA7: Add the build support in omap2plus
ARM: DRA7: hwmod: Reuse the soc_ops used for OMAP4/5
ARM: DRA7: id: Add cpu detection support for DRA7xx based SoCs'
ARM: DRA7: Kconfig: Make ARCH_NR_GPIO default to 512
ARM: DRA7: board-generic: Add basic DT support
ARM: DRA7: Resue the clocksource, clockevent support
ARM: DRA7: Reuse io tables and add a new .init_early
ARM: DRA7: Reuse all of PRCM and MPUSS SMP infra
Signed-off-by: Olof Johansson <olof@lixom.net>
Various OMAP PRCM & hwmod fixes and improvements. Notable changes
include:
- a fix for OMAP4 PLL locking to avoid a bootloader dependency that
causes nasty log spew on startup
- AM33xx DEBUGSS support fixes in hwmod data
- OMAP5 mailbox support in hwmod data
Basic test logs are here:
http://www.pwsan.com/omap/testlogs/prcm_a_for_v3.12/20130823125002/
Note that the 3530 failure is due to the mysterious transient serial
issue affecting 3530 for several releases now, which causes a log
parsing failure. PM still seems to work.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=K23I
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.12/prcm-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into late/all
From Tony Lindgren:
OMAP PRCM and hwmod fixes and improvments via Paul Walmsley <paul@pwsan.com>:
Various OMAP PRCM & hwmod fixes and improvements. Notable changes
include:
- a fix for OMAP4 PLL locking to avoid a bootloader dependency that
causes nasty log spew on startup
- AM33xx DEBUGSS support fixes in hwmod data
- OMAP5 mailbox support in hwmod data
Basic test logs are here:
http://www.pwsan.com/omap/testlogs/prcm_a_for_v3.12/20130823125002/
Note that the 3530 failure is due to the mysterious transient serial
issue affecting 3530 for several releases now, which causes a log
parsing failure. PM still seems to work.
* tag 'omap-for-v3.12/prcm-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: AM33xx: clock: Add RNG clock data
ARM: OMAP: TI81XX: add always-on powerdomain for TI81XX
ARM: OMAP4: clock: Lock PLLs in the right sequence
ARM: OMAP: AM33XX: hwmod: Add hwmod data for debugSS
ARM: OMAP2+: Only write the sysconfig on idle when necessary
ARM: OMAP5: hwmod data: Add mailbox data
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch moves the pca953x.h header from include/linux/i2c to
include/linux/platform_data and updates existing support accordingly.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The DPI and SDI platform devices are currently created with the ID of
-1. The ID doesn't currently affect anything.
However, we have added regulator supply entries for "omapdss_dpi.0" and
"omapdss_sdi.0" to the board files, although these supply entries are
not yet used. As the ID used for the devices is -1, these regulator
supply entries will not work.
To fix the issue, assign ID of 0 to the devices. In the future there may
be more than one DPI or SDI output, so it makes sense to have a proper
ID for them.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
Use new display drivers for AM3517EVM board.
The new OMAP display drivers were merged for 3.11, and we can now change
the board files to use the new ones and phase out the old ones.
Note: the management of LCD GPIOs is unclear. They were originally muxed
as inputs, and LCD_PANEL_PWR was labelled as "dvi enable".
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Use new display drivers for Zoom board.
The new OMAP display drivers were merged for 3.11, and we can now change
the board files to use the new ones and phase out the old ones.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Use new display drivers for OMAP3 Pandora board.
The new OMAP display drivers were merged for 3.11, and we can now change
the board files to use the new ones and phase out the old ones.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Use new display drivers for OMAP3EVM board.
The new OMAP display drivers were merged for 3.11, and we can now change
the board files to use the new ones and phase out the old ones.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Use new display drivers for 3430SDP board.
The new OMAP display drivers were merged for 3.11, and we can now change
the board files to use the new ones and phase out the old ones.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Use new display drivers for H4 board.
The new OMAP display drivers were merged for 3.11, and we can now change
the board files to use the new ones and phase out the old ones.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Use new display drivers for cm-t35 board.
The new OMAP display drivers were merged for 3.11, and we can now change
the board files to use the new ones and phase out the old ones.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Use new display drivers for igep0020 board.
The new OMAP display drivers were merged for 3.11, and we can now change
the board files to use the new ones and phase out the old ones.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Use new display drivers for OMAP3 Stalker board.
The new OMAP display drivers were merged for 3.11, and we can now change
the board files to use the new ones and phase out the old ones.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Use new display drivers for LDP board.
The new OMAP display drivers were merged for 3.11, and we can now change
the board files to use the new ones and phase out the old ones.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Use new display drivers for 2430SDP board.
The new OMAP display drivers were merged for 3.11, and we can now change
the board files to use the new ones and phase out the old ones.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Use new display drivers for devkit8000 board.
The new OMAP display drivers were merged for 3.11, and we can now change
the board files to use the new ones and phase out the old ones.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Use the new display drivers for Beagleboard.
The new OMAP display drivers were merged for 3.11, and we can now change
the board files to use the new ones and phase out the old ones.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Use the new display drivers for RX51 board.
The new OMAP display drivers were merged for 3.11, and we can now change
the board files to use the new ones and phase out the old ones.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Tony Lindgren <tony@atomide.com>
Use the new display drivers for OMAP3 Overo board.
The new OMAP display drivers were merged for 3.11, and we can now change
the board files to use the new ones and phase out the old ones.
Note that the LCD add-on boards for lcd43 and lcd35 use the same GPIOs
for the panels. This means that both panel devices cannot be probed at
the same time.
DT will handle this correctly, i.e. the DT data will contain the panel
device only for the add-on board that is attached. However, for the
board file we need a hackish solution: We parse the kernel boot command
line, and see whether lcd43 or lcd35 is set as a default display, and
add the given one. Or, if neither is given, default to lcd43.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
4430SDP board has an option for a PicoDLP mini-projector. PicoDLP cannot
be used at the same time as the second LCD, and there are GPIOs that
need to be set/unset when changing the used display.
Managing that kind of board specific setup is not simple without board
file callbacks. As only some 4430SDP boards actually have the PicoDLP
installed, and 4430SDP boards are not that common in the first place,
let's remove PicoDLP data from the board file.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Use the new display drivers for OMAP4 Panda and OMAP4 SDP boards.
The new OMAP display drivers were merged for 3.11, and we can now change
the board files to use the new ones and phase out the old ones.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
This is no longer needed as omap4 is now booted using device tree.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
This patch adds alwon powerdomain support for TI81XX, which is required
for stable functioning of a big number of TI81XX subsystems.
Signed-off-by: Aida Mynzhasova <aida.mynzhasova@skitlab.ru>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
On OMAP4 we have clk_set_rate()s being done for a few
DPLL clock nodes, as part of the clock init code, since
the bootloaders no longer locks these DPLLs.
So we have a clk_set_rate() done for a ABE DPLL node (which
inturn locks it) followed by a clk_set_rate() for the USB DPLL.
With USB DPLL being in bypass, we have this parent->child
relationship thats formed while the clocks get registered.
dpll_abe_ck
|
V
dpll_abe_x2_ck
|
V
dpll_abe_m3x2_ck
|
V
usb_hs_clk_div_ck
|
V
dpll_usb_ck
This is because usb_hs_clk_div_ck is bypass clock for dpll_usb_ck.
So with this parent->child relationship in place, a clk_set_rate()
on ABE DPLL results eventually in a clk_set_rate() call on USB DPLL,
because CCF does a clk_change_rate() (as part of clk_set_rate()) on
all downstream clocks resulting from a rate change on the top clock.
So its important that we lock USB DPLL before we lock ABE DPLL.
Without which we see these error logs at boot.
[These error logs will not be seen if using a bootloader that locks
USB DPLL]
[ 0.000000] clock: dpll_usb_ck failed transition to 'locked'
[ 0.000000] Division by zero in kernel.
[ 0.000000] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.10.0-03445-gfb2af00-dirty #7
[ 0.000000] [<c001bfe8>] (unwind_backtrace+0x0/0xf4) from [<c001868c>] (show_stack+0x10/0x14)
[ 0.000000] [<c001868c>] (show_stack+0x10/0x14) from [<c02deb28>] (Ldiv0+0x8/0x10)
[ 0.000000] [<c02deb28>] (Ldiv0+0x8/0x10) from [<c0477030>] (clk_divider_set_rate+0x10/0x114)
[ 0.000000] [<c0477030>] (clk_divider_set_rate+0x10/0x114) from [<c0476ef4>] (clk_change_rate+0x38/0xb8)
[ 0.000000] [<c0476ef4>] (clk_change_rate+0x38/0xb8) from [<c0476f5c>] (clk_change_rate+0xa0/0xb8)
[ 0.000000] Division by zero in kernel.
[ 0.000000] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.10.0-03445-gfb2af00-dirty #7
[ 0.000000] [<c001bfe8>] (unwind_backtrace+0x0/0xf4) from [<c001868c>] (show_stack+0x10/0x14)
[ 0.000000] [<c001868c>] (show_stack+0x10/0x14) from [<c02deb28>] (Ldiv0+0x8/0x10)
[ 0.000000] [<c02deb28>] (Ldiv0+0x8/0x10) from [<c0477030>] (clk_divider_set_rate+0x10/0x114)
[ 0.000000] [<c0477030>] (clk_divider_set_rate+0x10/0x114) from [<c0476ef4>] (clk_change_rate+0x38/0xb8)
[ 0.000000] [<c0476ef4>] (clk_change_rate+0x38/0xb8) from [<c0476f5c>] (clk_change_rate+0xa0/0xb8)
[ 0.000000] Division by zero in kernel.
[ 0.000000] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.10.0-03445-gfb2af00-dirty #7
[ 0.000000] [<c001bfe8>] (unwind_backtrace+0x0/0xf4) from [<c001868c>] (show_stack+0x10/0x14)
[ 0.000000] [<c001868c>] (show_stack+0x10/0x14) from [<c02deb28>] (Ldiv0+0x8/0x10)
[ 0.000000] [<c02deb28>] (Ldiv0+0x8/0x10) from [<c0477030>] (clk_divider_set_rate+0x10/0x114)
[ 0.000000] [<c0477030>] (clk_divider_set_rate+0x10/0x114) from [<c0476ef4>] (clk_change_rate+0x38/0xb8)
[ 0.000000] [<c0476ef4>] (clk_change_rate+0x38/0xb8) from [<c0476f5c>] (clk_change_rate+0xa0/0xb8)
[ 0.000000] Division by zero in kernel.
[ 0.000000] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.10.0-03445-gfb2af00-dirty #7
[ 0.000000] [<c001bfe8>] (unwind_backtrace+0x0/0xf4) from [<c001868c>] (show_stack+0x10/0x14)
[ 0.000000] [<c001868c>] (show_stack+0x10/0x14) from [<c02deb28>] (Ldiv0+0x8/0x10)
[ 0.000000] [<c02deb28>] (Ldiv0+0x8/0x10) from [<c0477030>] (clk_divider_set_rate+0x10/0x114)
[ 0.000000] [<c0477030>] (clk_divider_set_rate+0x10/0x114) from [<c0476ef4>] (clk_change_rate+0x38/0xb8)
[ 0.000000] [<c0476ef4>] (clk_change_rate+0x38/0xb8) from [<c0476f5c>] (clk_change_rate+0xa0/0xb8)
[ 0.000000] Division by zero in kernel.
[ 0.000000] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.10.0-03445-gfb2af00-dirty #7
[ 0.000000] [<c001bfe8>] (unwind_backtrace+0x0/0xf4) from [<c001868c>] (show_stack+0x10/0x14)
[ 0.000000] [<c001868c>] (show_stack+0x10/0x14) from [<c02deb28>] (Ldiv0+0x8/0x10)
[ 0.000000] [<c02deb28>] (Ldiv0+0x8/0x10) from [<c0477030>] (clk_divider_set_rate+0x10/0x114)
[ 0.000000] [<c0477030>] (clk_divider_set_rate+0x10/0x114) from [<c0476ef4>] (clk_change_rate+0x38/0xb8)
[ 0.000000] [<c0476ef4>] (clk_change_rate+0x38/0xb8) from [<c0476f5c>] (clk_change_rate+0xa0/0xb8)
[ 0.000000] Division by zero in kernel.
[ 0.000000] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.10.0-03445-gfb2af00-dirty #7
[ 0.000000] [<c001bfe8>] (unwind_backtrace+0x0/0xf4) from [<c001868c>] (show_stack+0x10/0x14)
[ 0.000000] [<c001868c>] (show_stack+0x10/0x14) from [<c02deb28>] (Ldiv0+0x8/0x10)
[ 0.000000] [<c02deb28>] (Ldiv0+0x8/0x10) from [<c0477030>] (clk_divider_set_rate+0x10/0x114)
[ 0.000000] [<c0477030>] (clk_divider_set_rate+0x10/0x114) from [<c0476ef4>] (clk_change_rate+0x38/0xb8)
[ 0.000000] [<c0476ef4>] (clk_change_rate+0x38/0xb8) from [<c0476f5c>] (clk_change_rate+0xa0/0xb8)
[ 0.000000] clock: trace_clk_div_ck: could not find divisor for target rate 0 for parent pmd_trace_clk_mux_ck
[ 0.000000] Division by zero in kernel.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
In the original hwmod data file, DebugSS entry was disabled,
since we didn't (and do not) have SW to control it.
This patch enables it back with right data, so that it can be
controlled by different ways; and the suggested method it to
have modular driver for debugSS as well.
Refer to the link for more discussion on handling of debugSS -
https://patchwork.kernel.org/patch/2212111/
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Currently, whenever we idle a device _idle_sysc() is called and writes to the
devices SYSCONFIG register to set the idle mode. A lot devices are using the
smart-idle mode and so the write to the SYSCONFIG register is programming the
same value that is already stored in the register.
Writes to the devices SYSCONFIG register can be slow, for example, writing to
the DMTIMER SYSCONFIG register takes 3 interface clock cycles and 3 functional
clock cycles. If the DMTIMER is using the slow 32kHz functional clock this can
take ~100us.
Furthermore, during boot on an OMAP4430 panda board, I see that there are 100
calls to _idle_sysc(), however, only 3 out of the 100 calls actually write
the SYSCONFIG register with a new value.
Therefore, to avoid unnecessary writes to device SYSCONFIG registers when
idling the device, only write the value if the value has changed. It should be
safe to do this on idle as the context of the register will never be lost while
the device is active.
Verified that suspend, CORE off and retention states are working with this
change on OMAP3430 Beagle board.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
[paul@pwsan.com: updated to apply]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Pali Rohár
Simon Barth
Tony Lindgren
Nishanth Menon
Aaro Koskinen
Phil Carmody
Anoop Thomas Mathew
Vladimir Murzin
Fabio Estevam
Wei Yongjun
Linus Torvalds
Herbert Xu
Olof Johansson
Vivien Didelot
Tomi Valkeinen
Paul Walmsley
Lokesh Vutla
Aida Mynzhasova
Rajendra Nayak
Vaibhav Hiremath
Jon Hunter
Ambresh K