Rather than looking inside the definition of a DeviceState with
"s->qdev", use the QOM prefered style: "DEVICE(s)".
This patch was generated using the following Coccinelle script:
// Use DEVICE() macros to access DeviceState.qdev
@use_device_macro_to_access_qdev@
expression obj;
identifier dev;
@@
-&obj->dev.qdev
+DEVICE(obj)
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20190528164020.32250-9-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Add support for per port power switching.
Virtual power of course ;)
Use port-power=on property to enable this.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20190524070310.4952-6-kraxel@redhat.com
Helper function to update port status bits which depends on the
connected device. We need the same logic for device attach and
port reset, so factor it out.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190524070310.4952-5-kraxel@redhat.com
Add usb_hub_port_set() and usb_hub_port_clear() helpers which care about
updating the change bits (port->wPortChange) properly, so we don't need
to have that logic sprinkled all over the place ;)
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20190524070310.4952-4-kraxel@redhat.com
Add num_ports property which allows configure the number of downstream
ports. Valid range is 1-8, default is 8.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20190524070310.4952-3-kraxel@redhat.com
Add dashes, so they don't look like two separate things when printed.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190524070310.4952-2-kraxel@redhat.com
Seems some devices become confused when we call
libusb_set_configuration(). So before calling the function check
whenever the device has multiple configurations in the first place, and
in case it hasn't (which is the case for the majority of devices) simply
skip the call as it will have no effect anyway.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20190522094702.17619-4-kraxel@redhat.com
If the guest didn't talk to the device yet, skip the reset.
Without this usb-host devices get resetted a number of times
at boot time for no good reason.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20190522094702.17619-3-kraxel@redhat.com
That way the device reset handler can see what
the before-reset state of the device is.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20190522094702.17619-2-kraxel@redhat.com
hw/usb/hcd-xhci.c: In function ‘usb_xhci_realize’:
hw/usb/hcd-xhci.c:3339:66: warning: ‘%d’ directive output may be truncated writing between 1 and 10 bytes into a region of size 5 [-Wformat-trunca\
tion=]
3339 | snprintf(port->name, sizeof(port->name), "usb2 port #%d", i+1);
| ^~
hw/usb/hcd-xhci.c:3339:54: note: directive argument in the range [1, 2147483647]
3339 | snprintf(port->name, sizeof(port->name), "usb2 port #%d", i+1);
| ^~~~~~~~~~~~~~~
The xhci code formats the port name into a fixed length
buffer which is only large enough to hold port numbers
upto 5 digits in decimal representation. We're never
going to have a port number that large, so aserting the
port number is sensible is sufficient to tell GCC the
formatted string won't be truncated.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20190412121626.19829-5-berrange@redhat.com>
[ kraxel: also s/int/unsigned int/ to tell gcc they can't
go negative. ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Some machines (like the pxa2xx-based ARM machines) only have a sysbus
OHCI controller, but no PCI. With the new Kconfig-style build system,
it will soon be possible to create QEMU binaries that only contain
such PCI-less machines. However, the two OHCI controllers, for sysbus
and for PCI, are currently both located in one file, so the PCI code
is still required for linking here. Move the OHCI-PCI device code
into a separate file, so that it is possible to use the sysbus OHCI
device also without the PCI dependency.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190419075625.24251-3-thuth@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The ohci_die() function always assumes to be running with a PCI OHCI
controller and calls the PCI-specific functions pci_set_word(). However,
this function might also get called for the sysbus OHCI devices, so it
likely fails in that case. To fix this issue, change the code now, so that
there are two implementations now, one for sysbus and one for PCI, and
use the right function via a function pointer in the OHCIState structure.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190419075625.24251-2-thuth@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
we found the following core in our environment:
0 0x00007fc6b06c2237 in raise ()
1 0x00007fc6b06c3928 in abort ()
2 0x00007fc6b06bb056 in __assert_fail_base ()
3 0x00007fc6b06bb102 in __assert_fail ()
4 0x0000000000702e36 in xhci_kick_ep (...)
5 0x000000000047897a in memory_region_write_accessor (...)
6 0x000000000047767f in access_with_adjusted_size (...)
7 0x000000000047944d in memory_region_dispatch_write (...)
(mr=mr@entry=0x7fc6a0138df0, addr=addr@entry=156, data=1648892416,
size=size@entry=4, attrs=attrs@entry=...)
8 0x000000000042df17 in address_space_write_continue (...)
10 0x000000000043084d in address_space_rw (...)
11 0x000000000047451b in kvm_cpu_exec (cpu=cpu@entry=0x1ab11b0)
12 0x000000000045dcf5 in qemu_kvm_cpu_thread_fn (arg=0x1ab11b0)
13 0x0000000000870631 in qemu_thread_start (args=args@entry=0x1acfb50)
14 0x00000000008959a7 in thread_entry_for_hotfix (pthread_cb=<optimized out>)
15 0x00007fc6b0a60dd5 in start_thread ()
16 0x00007fc6b078a59d in clone ()
(gdb) f 5
5 0x000000000047897a in memory_region_write_accessor (...)
529 mr->ops->write(mr->opaque, addr, tmp, size);
(gdb) p /x tmp
$9 = 0x62481a00 <-- last byte 0x00 is @epid
xhci_doorbell_write() already check the upper bound of @slotid an @epid,
it also need to check the lower bound.
Cc: Gonglei <arei.gonglei@huawei.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Longpeng <longpeng2@huawei.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 1556605301-44112-1-git-send-email-longpeng2@huawei.com
[ kraxel: fixed typo in subject line ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Commit c5ead51f90 (usb-mtp: return incomplete transfer on a lstat
failure) checks if lstat succeeded when updating attributes of a
file. However, it also changed behavior to return an error by
default. This is incorrect because for smaller file sizes, Qemu
will attempt to write the file in one go and there won't be
an object for it.
Fixes: c5ead51f90
Signed-off-by: Bandan Das <bsd@redhat.com>
Message-id: jpgwojv9pwv.fsf@linux.bootlegged.copy
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The ObjectInfo struct's "filename" field is following a uint8_t
field in a packed struct and thus has bad alignment for a 16-bit
field. Switch the field to to uint8_t and use the helper function
for accessing unaligned 16-bit data.
Note that although the MTP spec specifies big endian, when transported
over the USB protocol, data is little endian.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Message-id: 20190415154503.6758-4-berrange@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The ObjectInfo 'length' field provides the length of the
wide character string filename. This is then converted to
a multi-byte character string. This may have a different
byte count to the wide character string. We should use the
C string length of the multi-byte string instead.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Message-id: 20190415154503.6758-2-berrange@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The ObjectInfo struct has a variable length array containing the UTF-16
encoded filename. The number of characters of trailing data is given by
the 'length' field in the struct and this must be validated against the
size of the data packet received from the guest.
Since the data is UTF-16, we must convert the byte count we have to a
character count before validating. This must take care to truncate if
a malicious guest sent an odd number of bytes.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Bandan Das <bsd@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Watch IDs are allocated from incrementing a int counter against
the QFileMonitor object. In very long life QEMU processes with
a huge amount of USB MTP activity creating & deleting directories
it is just about conceivable that the int counter can wrap
around. This would result in incorrect behaviour of the file
monitor watch APIs due to clashing watch IDs.
Instead of trying to detect this situation, this patch changes
the way watch IDs are allocated. It is turned into an int64_t
variable where the high 32 bits are set from the underlying
inotify "int" ID. This gives an ID that is guaranteed unique
for the directory as a whole, and we can rely on the kernel
to enforce this. QFileMonitor then sets the low 32 bits from
a per-directory counter.
The USB MTP device only sets watches on the directory as a
whole, not files within, so there is no risk of guest
triggered wrap around on the low 32 bits.
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
This function is used in the delete path only and can
be replaced by a call to usb_mtp_object_free.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Bandan Das <bsd@redhat.com>
Message-Id: <20190401211712.19012-3-bsd@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Spotted by Coverity: CID 1399414
mtp delete allows the return status of delete succeeded,
partial_delete or readonly - when none of the objects could be
deleted. Give more meaningful names to return values of the
delete function.
Some initiators recurse over the objects themselves. In that case,
only READ_ONLY can be returned.
Signed-off-by: Bandan Das <bsd@redhat.com>
Message-Id: <20190401211712.19012-2-bsd@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
In usb_mask_to_str() we convert a mask of USB speeds into
a human-readable string (like "full+high") for use in
tracing and error messages. However the conversion code
doesn't do anything to the string buffer if the passed in
speedmask doesn't match any of the recognized speeds,
which means that the tracing and error messages will
end up with random garbage in them. This can happen if
we're doing USB device passthrough.
Handle the "unrecognized speed" case by using the
string "unknown".
Fixes: https://bugs.launchpad.net/qemu/+bug/1603785
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20190328133503.6490-1-peter.maydell@linaro.org
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
We spell out sub/dir/ in sub/dir/trace-events' comments pointing to
source files. That's because when trace-events got split up, the
comments were moved verbatim.
Delete the sub/dir/ part from these comments. Gets rid of several
misspellings.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190314180929.27722-3-armbru@redhat.com
Message-Id: <20190314180929.27722-3-armbru@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
I had to include an enum for audio sampling formats into qapi, but that
meant duplicating the audfmt_e enum. This patch replaces audfmt_e and
associated values with the qapi generated AudioFormat enum.
This patch is mostly a search-and-replace, except for switches where the
qapi generated AUDIO_FORMAT_MAX caused problems.
Signed-off-by: Kővágó, Zoltán <DirtY.iCE.hu@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 01251b2758a1679c66842120b77c0fb46d7d0eaf.1552083282.git.DirtY.iCE.hu@gmail.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This automatically removes the SCSI subsystem from the
binary altogether if no controllers are selected.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20190123065618.3520-34-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Instead of including the same list of devices for each target,
let the host controllers select CONFIG_USB and make the devices
default to present whenever USB is available.
Done with the following script:
while read i; do
i=${i%=y}; i=${i#CONFIG_}
sed -i -e'/^config '$i'$/!b' -en \
-e'a\' -e' default y\' -e' depends on USB' \
`grep -lw $i hw/*/Kconfig`
done < default-configs/usb.mak
followed by adding "select USB" on the host controllers.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-33-yang.zhong@intel.com>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Instead of including the same list of devices for each target,
set CONFIG_PCI to true, and make the devices default to present
whenever PCI is available. However, s390x does not want all the
PCI devices, so there is a separate symbol to enable them.
Done mostly with the following script:
while read i; do
i=${i%=y}; i=${i#CONFIG_}
sed -i -e'/^config '$i'$/!b' -en \
-e'a\' -e' default y if PCI_DEVICES\' -e' depends on PCI' \
`grep -lw $i hw/*/Kconfig`
done < default-configs/pci.mak
followed by replacing a few "depends on" clauses with "select"
whenever the symbol is not really related to PCI.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-31-yang.zhong@intel.com>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The Kconfig files were generated mostly with this script:
for i in `grep -ho CONFIG_[A-Z0-9_]* default-configs/* | sort -u`; do
set fnord `git grep -lw $i -- 'hw/*/Makefile.objs' `
shift
if test $# = 1; then
cat >> $(dirname $1)/Kconfig << EOF
config ${i#CONFIG_}
bool
EOF
git add $(dirname $1)/Kconfig
else
echo $i $*
fi
done
sed -i '$d' hw/*/Kconfig
for i in hw/*; do
if test -d $i && ! test -f $i/Kconfig; then
touch $i/Kconfig
git add $i/Kconfig
fi
done
Whenever a symbol is referenced from multiple subdirectories, the
script prints the list of directories that reference the symbol.
These symbols have to be added manually to the Kconfig files.
Kconfig.host and hw/Kconfig were created manually.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20190123065618.3520-27-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
With certain USB devices passed through via usb-host, a guest attempting to
reset a usb-host device can trigger a reset loop that renders the USB device
unusable. In my use case, the device was an iPhone XR that was passed through to
a Mac OS X Mojave guest. Upon connecting the device, the following happens:
1) Guest recognizes new device, sends reset to emulated USB host
2) QEMU's USB host sends reset to host kernel
3) Host kernel resets device
4) After reset, host kernel determines that some part of the device descriptor
has changed ("device firmware changed" in dmesg), so host kernel decides to
re-enumerate the device.
5) Re-enumeration causes QEMU to disconnect and reconnect the device in the
guest.
6) goto 1)
Here's from the host kernel (note the "device firmware changed" lines")
[3677704.473050] usb 1-1.3: new high-speed USB device number 53 using ehci-pci
[3677704.555594] usb 1-1.3: New USB device found, idVendor=05ac, idProduct=12a8, bcdDevice=11.08
[3677704.555599] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[3677704.555602] usb 1-1.3: Product: iPhone
[3677704.555605] usb 1-1.3: Manufacturer: Apple Inc.
[3677704.555607] usb 1-1.3: SerialNumber: [[removed]]
[3677709.401040] usb 1-1.3: reset high-speed USB device number 53 using ehci-pci
[3677709.479486] usb 1-1.3: device firmware changed
[3677709.479842] usb 1-1.3: USB disconnect, device number 53
[3677709.546039] usb 1-1.3: new high-speed USB device number 54 using ehci-pci
[3677709.627471] usb 1-1.3: New USB device found, idVendor=05ac, idProduct=12a8, bcdDevice=11.08
[3677709.627476] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[3677709.627479] usb 1-1.3: Product: iPhone
[3677709.627481] usb 1-1.3: Manufacturer: Apple Inc.
[3677709.627483] usb 1-1.3: SerialNumber: [[removed]]
[3677762.320044] usb 1-1.3: reset high-speed USB device number 54 using ehci-pci
[3677762.615630] usb 1-1.3: USB disconnect, device number 54
[3677762.787043] usb 1-1.3: new high-speed USB device number 55 using ehci-pci
[3677762.869016] usb 1-1.3: New USB device found, idVendor=05ac, idProduct=12a8, bcdDevice=11.08
[3677762.869024] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[3677762.869028] usb 1-1.3: Product: iPhone
[3677762.869032] usb 1-1.3: Manufacturer: Apple Inc.
[3677762.869035] usb 1-1.3: SerialNumber: [[removed]]
[3677815.662036] usb 1-1.3: reset high-speed USB device number 55 using ehci-pci
Here's from QEMU:
libusb: error [_get_usbfs_fd] libusb couldn't open USB device /dev/bus/usb/005/022: No such file or directory
libusb: error [udev_hotplug_event] ignoring udev action bind
libusb: error [udev_hotplug_event] ignoring udev action bind
libusb: error [_open_sysfs_attr] open /sys/bus/usb/devices/5-1/bConfigurationValue failed ret=-1 errno=2
libusb: error [_get_usbfs_fd] File doesn't exist, wait 10 ms and try again
libusb: error [_get_usbfs_fd] libusb couldn't open USB device /dev/bus/usb/005/024: No such file or directory
libusb: error [udev_hotplug_event] ignoring udev action bind
libusb: error [udev_hotplug_event] ignoring udev action bind
libusb: error [_open_sysfs_attr] open /sys/bus/usb/devices/5-1/bConfigurationValue failed ret=-1 errno=2
libusb: error [_get_usbfs_fd] File doesn't exist, wait 10 ms and try again
libusb: error [_get_usbfs_fd] libusb couldn't open USB device /dev/bus/usb/005/026: No such file or directory
The result of this is that the device remains permanently unusable in the guest.
The same problem has been previously reported for an iPad:
https://stackoverflow.com/questions/52617634/how-do-i-get-qemu-usb-passthrough-to-work-for-ipad-iphone
This problem can be elegantly solved by interrupting step 2) above. Instead of
passing through the reset, QEMU simply ignores it. To allow this to be
configured on a per-device level, a new parameter "no_guest_reset" is
introduced for the usb-host device. I can confirm that the configuration
described above (iPhone XS + Mojave guest) works flawlessly with
no_guest_reset=True specified.
Working command line for my scenario:
device_add usb-host,vendorid=0x05ac,productid=0x12a8,no_guest_reset=True,id=iphone
Best regards
Alexander
Signed-off-by: Alexander Kappner <agk@godking.net>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20190128140027.9448-1-kraxel@redhat.com
[ kraxel: rename parameter to "guest-reset" ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
During a write, free up the "path" before getting more data.
Also, while we at it, remove the confusing usage of d->fd for
storing mkdir status
Spotted by Coverity: CID 1398642
Signed-off-by: Bandan Das <bsd@redhat.com>
Message-id: 20190306210409.14842-3-bsd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
MTP writes objects in small chunks and at the end gets the
real file size to update the object metadata. If this fails for
any reason, return an INCOMPLETE_TRANSFER to the initiator
Spotted by Coverity: CID 1398651
Signed-off-by: Bandan Das <bsd@redhat.com>
Message-id: 20190306210409.14842-2-bsd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The internal inotify APIs allow a lot of conditional statements to be
cleared out, and provide a simpler callback for handling events.
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Various functions accepting 'char *' string parameters were missing
'const' qualifiers.
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
IN_ISDIR is not a bit that one can request when registering a
watch with inotify_add_watch. Rather it is a bit that is set
automatically when reading events from the kernel.
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
No caller of usb_ep_get() calls it with a NULL device (previous commits
have addressed the few remaining cases which didn't explicitly check).
Replace check for 'dev == NULL' with an assert instead.
Signed-off-by: Liam Merwick <liam.merwick@oracle.com>
Message-id: 1549460216-25808-10-git-send-email-liam.merwick@oracle.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Add an assert and an explicit check before the two callers to
usb_ep_get() in the USB redirector code to ensure the device
passed in is not NULL.
Signed-off-by: Liam Merwick <liam.merwick@oracle.com>
Message-id: 1549460216-25808-9-git-send-email-liam.merwick@oracle.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
In musb_packet(), the call to usb_find_device() can return NULL
if it doesn't find a device matching 'addr' so explicitly check
the return value before passing it to usb_ep_get(). This then
allows the subsequent calculation of 'id' to be streamlined.
Signed-off-by: Liam Merwick <liam.merwick@oracle.com>
Message-id: 1549460216-25808-8-git-send-email-liam.merwick@oracle.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
In uhci_handle_td(), the call to ehci_find_device() can return NULL
if it doesn't find a device matching 'addr' so explicitly check
the return value before passing it to usb_ep_get().
Signed-off-by: Liam Merwick <liam.merwick@oracle.com>
Message-id: 1549460216-25808-7-git-send-email-liam.merwick@oracle.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
A call to ohci_find_device() can return NULL if it doesn't find a
device matching 'addr' so for the two callers, explicitly check
the return value before passing it to usb_ep_get().
Signed-off-by: Liam Merwick <liam.merwick@oracle.com>
Message-id: 1549460216-25808-6-git-send-email-liam.merwick@oracle.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
In ehci_process_itd(), the call to ehci_find_device() can return NULL
if it doesn't find a device matching 'devaddr' so explicitly check
the return value before passing it to usb_ep_get().
Signed-off-by: Liam Merwick <liam.merwick@oracle.com>
Message-id: 1549460216-25808-5-git-send-email-liam.merwick@oracle.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Most callers of xhci_port_update() and xhci_wakeup() pass in a pointer
to an array entry and can never be NULL but add two defensive asserts
to protect against future changes (e.g. adding a new port speed, etc.)
adding a path through xhci_lookup_port() that could result in the
return of a NULL XHCIPort.
Signed-off-by: Liam Merwick <liam.merwick@oracle.com>
Message-id: 1549460216-25808-3-git-send-email-liam.merwick@oracle.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
There is no need to calculate the 'eps' variable in usb_ep_get()
if 'ep' is the control endpoint. Instead the calculation should
be done after validating the input before returning an entry
indexed by the endpoint 'ep'.
Signed-off-by: Liam Merwick <liam.merwick@oracle.com>
Reviewed-by: Darren Kenny <Darren.Kenny@oracle.com>
Reviewed-by: Mark Kanda <Mark.Kanda@oracle.com>
Reviewed-by: Ameya More <ameya.more@oracle.com>
Message-id: 1549460216-25808-2-git-send-email-liam.merwick@oracle.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Certain devices types, like memory/CPU, are now being handled using a
hotplug interface provided by a top-level MachineClass. Hotpluggable
host bridges are another such device where it makes sense to use a
machine-level hotplug handler. However, unlike those devices,
host-bridges have a parent bus (the main system bus), and devices with
a parent bus use a different mechanism for registering their hotplug
handlers: qbus_set_hotplug_handler(). This interface currently expects
a handler to be a subclass of DeviceClass, but this is not the case
for MachineClass, which derives directly from ObjectClass.
Internally, the interface only requires an ObjectClass, so expose that
in qbus_set_hotplug_handler().
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <154999589921.690774.3640149277362188566.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This will be needed by vhost-user-test, when each test switches to
its own GMainLoop and GMainContext. Otherwise, for a reconnecting
socket the initial connection will happen on the default GMainContext,
and no one will be listening on it.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20190202110834.24880-1-pbonzini@redhat.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
qemu_write_full takes care of partial blocking writes,
as in cases of larger file sizes
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Bandan Das <bsd@redhat.com>
Message-id: 20190129131908.27924-4-bsd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
For every MTP_WRITE_BUF_SZ copied, this patch writes it to file before
getting the next block of data. The file is kept opened for the
duration of the operation but the sanity checks on the write operation
are performed only once when the write operation starts. Additionally,
we also update the file size in the object metadata once the file has
completely been written.
Suggested-by: Gerd Hoffman <kraxel@redhat.com>
Signed-off-by: Bandan Das <bsd@redhat.com>
Message-id: 20190129131908.27924-3-bsd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This is a "pre-patch" to breaking up the write buffer for
MTP writes. Instead of allocating a mtp buffer equal to size
sent by the initiator, we start with a small size and reallocate
multiples (of that small size) as needed.
Signed-off-by: Bandan Das <bsd@redhat.com>
Message-id: 20190129131908.27924-2-bsd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Implement underrun/overrun events of isochronous endpoints
according to XHCI spec (4.10.3.1)
Guest software restarts data streaming when receives these events.
The XHCI reports these events using interrupter assigned
to the slot (as these events do not have TRB), so current
commit adds the field of assigned interrupter to the
XHCISlot structure. Guest software assigns interrupter to the
slot on 'Address Device' and 'Evaluate Context' commands.
Signed-off-by: Yuri Benditovich <yuri.benditovich@janustech.com>
Message-id: 20190128200444.5128-3-yuri.benditovich@janustech.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
According to the XHCI spec (4.10.2) the controller
never halts isochronous endpoints. This commit prevent
stop of isochronous streaming when sporadic errors
status received from backends.
Signed-off-by: Yuri Benditovich <yuri.benditovich@janustech.com>
Message-id: 20190128200444.5128-2-yuri.benditovich@janustech.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
It's either "GNU *Library* General Public version 2" or "GNU Lesser
General Public version *2.1*", but there was no "version 2.0" of the
"Lesser" library. So assume that version 2.1 is meant here.
Additionally, suggest that the user should have received a copy of
the LGPL, and not the GPL here.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-id: 1548254454-7659-1-git-send-email-thuth@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Spotted by Coverity: CID 1397070
Signed-off-by: Li Qiang <liq3ea@163.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190103133113.49599-1-liq3ea@163.com
[ kraxel: dropped chunk which adds close() after successful
fdopendir() call, that is not needed according to
POSIX even though Coverity flags it as bug ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Windows guests have trouble dealing with usb devices having identical
serial numbers. So, assign unique serial numbers to usb hid devices.
All other usb devices have this already.
In the past the fixed serial number has been used to indicate working
remote setup to linux guests. Here is a bit of history:
* First there was nothing.
* Then I added a rule to udev checking for serial == 42.
(this is in rhel-6).
* Then systemd + udev merged.
* Then I changed the rule to check for serial != 1 instead, so we can
use any serial but "1" which is the one the old broken devices had
(this is in rhel-7). March 2014 in upstream systemd.
* Then all usb power management rules where dropped from systemd (June
2015). Which I figured today (Sept 2018), after wondering that the
rules are gone in fedora 28.
So, three years ago the serial number check was dropped upstream, yet I
hav't seen a single report about autosuspend issues (or cpu usage for
usb emulation going up, which is the typical symtom).
So I figured I can stop worring that changing the serial number will
break things and just do it.
And even if it turns out autosuspend is still an issue: I think
meanwhile we can really stop worrying about guests running in old qemu
versions with broken usb suspend (fixed in 0.13 !). If needed we can
enable autosuspend unconditionally in guests.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20190110125108.22834-1-kraxel@redhat.com
...and xen_backend.h to xen-legacy-backend.h
Rather than attempting to convert the existing backend infrastructure to
be QOM compliant (which would be hard to do in an incremental fashion),
subsequent patches will introduce a completely new framework for Xen PV
backends. Hence it is necessary to re-name parts of existing code to avoid
name clashes. The re-named 'legacy' infrastructure will be removed once all
backends have been ported to the new framework.
This patch is purely cosmetic. No functional change.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Anthony Perard <anthony.perard@citrix.com>
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
* esp bugfixes (Guenter)
* Windows build cleanup (Marc-André)
* checkpatch logic improvements (Paolo)
* coalesced range bugfix (Paolo)
* switch testsuite to TAP (Paolo)
* QTAILQ rewrite (Paolo)
* block/iscsi.c cancellation fixes (Stefan)
* improve selection of the default accelerator (Thomas)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJcOKyMAAoJEL/70l94x66DxKEH/1ho2Xl8ezxCecA6q3HqTgMT
NJ/ntdqQwVwekKOWzsywnM3/LkEDLH55MxbTeQ8M/Vb1seS8eROz24/gPTzvFrfR
n/d11rDV1EJfWe0H7nGLLFiRv0MSjxLpG9c3dlOKWhwOYHm25tr48PsdfVFP9Slz
BK3rwrMeDgArfptHAIsAXt2h1S0EzrG9pMwGDpErCDzziXxBhUESE0Iqfw8LsH1K
VjMn6rn7Ts1XKlxxwsm+BzHlTJghbj3tWPIfk+6uK2isP4iM3gFCoav3SG9XVXof
V9+vFyMxdtZKT/0HvajhUS4/1S/uGBNNchZRnCxXlpbueWc5ROtvarhM6Hb0eck=
=i8E5
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging
* HAX support for Linux hosts (Alejandro)
* esp bugfixes (Guenter)
* Windows build cleanup (Marc-André)
* checkpatch logic improvements (Paolo)
* coalesced range bugfix (Paolo)
* switch testsuite to TAP (Paolo)
* QTAILQ rewrite (Paolo)
* block/iscsi.c cancellation fixes (Stefan)
* improve selection of the default accelerator (Thomas)
# gpg: Signature made Fri 11 Jan 2019 14:47:40 GMT
# gpg: using RSA key BFFBD25F78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>"
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>"
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* remotes/bonzini/tags/for-upstream: (34 commits)
avoid TABs in files that only contain a few
remove space-tab sequences
scripts: add script to convert multiline comments into 4-line format
hw/watchdog/wdt_i6300esb: remove a unnecessary comment
checkpatch: warn about qemu/queue.h head structs that are not typedef-ed
qemu/queue.h: simplify reverse access to QTAILQ
qemu/queue.h: reimplement QTAILQ without pointer-to-pointers
qemu/queue.h: remove Q_TAILQ_{HEAD,ENTRY}
qemu/queue.h: typedef QTAILQ heads
qemu/queue.h: leave head structs anonymous unless necessary
vfio: make vfio_address_spaces static
qemu/queue.h: do not access tqe_prev directly
test: replace gtester with a TAP driver
test: execute g_test_run when tests are skipped
qga: drop < Vista compatibility
build-sys: build with Vista API by default
build-sys: move windows defines in osdep.h header
build-sys: don't include windows.h, osdep.h does it
scsi: esp: Defer command completion until previous interrupts have been handled
esp-pci: Fix status register write erase control
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Most files that have TABs only contain a handful of them. Change
them to spaces so that we don't confuse people.
disas, standard-headers, linux-headers and libdecnumber are imported
from other projects and probably should be exempted from the check.
Outside those, after this patch the following files still contain both
8-space and TAB sequences at the beginning of the line. Many of them
have a majority of TABs, or were initially committed with all tabs.
bsd-user/i386/target_syscall.h
bsd-user/x86_64/target_syscall.h
crypto/aes.c
hw/audio/fmopl.c
hw/audio/fmopl.h
hw/block/tc58128.c
hw/display/cirrus_vga.c
hw/display/xenfb.c
hw/dma/etraxfs_dma.c
hw/intc/sh_intc.c
hw/misc/mst_fpga.c
hw/net/pcnet.c
hw/sh4/sh7750.c
hw/timer/m48t59.c
hw/timer/sh_timer.c
include/crypto/aes.h
include/disas/bfd.h
include/hw/sh4/sh.h
libdecnumber/decNumber.c
linux-headers/asm-generic/unistd.h
linux-headers/linux/kvm.h
linux-user/alpha/target_syscall.h
linux-user/arm/nwfpe/double_cpdo.c
linux-user/arm/nwfpe/fpa11_cpdt.c
linux-user/arm/nwfpe/fpa11_cprt.c
linux-user/arm/nwfpe/fpa11.h
linux-user/flat.h
linux-user/flatload.c
linux-user/i386/target_syscall.h
linux-user/ppc/target_syscall.h
linux-user/sparc/target_syscall.h
linux-user/syscall.c
linux-user/syscall_defs.h
linux-user/x86_64/target_syscall.h
slirp/cksum.c
slirp/if.c
slirp/ip.h
slirp/ip_icmp.c
slirp/ip_icmp.h
slirp/ip_input.c
slirp/ip_output.c
slirp/mbuf.c
slirp/misc.c
slirp/sbuf.c
slirp/socket.c
slirp/socket.h
slirp/tcp_input.c
slirp/tcpip.h
slirp/tcp_output.c
slirp/tcp_subr.c
slirp/tcp_timer.c
slirp/tftp.c
slirp/udp.c
slirp/udp.h
target/cris/cpu.h
target/cris/mmu.c
target/cris/op_helper.c
target/sh4/helper.c
target/sh4/op_helper.c
target/sh4/translate.c
tcg/sparc/tcg-target.inc.c
tests/tcg/cris/check_addo.c
tests/tcg/cris/check_moveq.c
tests/tcg/cris/check_swap.c
tests/tcg/multiarch/test-mmap.c
ui/vnc-enc-hextile-template.h
ui/vnc-enc-zywrle.h
util/envlist.c
util/readline.c
The following have only TABs:
bsd-user/i386/target_signal.h
bsd-user/sparc64/target_signal.h
bsd-user/sparc64/target_syscall.h
bsd-user/sparc/target_signal.h
bsd-user/sparc/target_syscall.h
bsd-user/x86_64/target_signal.h
crypto/desrfb.c
hw/audio/intel-hda-defs.h
hw/core/uboot_image.h
hw/sh4/sh7750_regnames.c
hw/sh4/sh7750_regs.h
include/hw/cris/etraxfs_dma.h
linux-user/alpha/termbits.h
linux-user/arm/nwfpe/fpopcode.h
linux-user/arm/nwfpe/fpsr.h
linux-user/arm/syscall_nr.h
linux-user/arm/target_signal.h
linux-user/cris/target_signal.h
linux-user/i386/target_signal.h
linux-user/linux_loop.h
linux-user/m68k/target_signal.h
linux-user/microblaze/target_signal.h
linux-user/mips64/target_signal.h
linux-user/mips/target_signal.h
linux-user/mips/target_syscall.h
linux-user/mips/termbits.h
linux-user/ppc/target_signal.h
linux-user/sh4/target_signal.h
linux-user/sh4/termbits.h
linux-user/sparc64/target_syscall.h
linux-user/sparc/target_signal.h
linux-user/x86_64/target_signal.h
linux-user/x86_64/termbits.h
pc-bios/optionrom/optionrom.h
slirp/mbuf.h
slirp/misc.h
slirp/sbuf.h
slirp/tcp.h
slirp/tcp_timer.h
slirp/tcp_var.h
target/i386/svm.h
target/sparc/asi.h
target/xtensa/core-dc232b/xtensa-modules.inc.c
target/xtensa/core-dc233c/xtensa-modules.inc.c
target/xtensa/core-de212/core-isa.h
target/xtensa/core-de212/xtensa-modules.inc.c
target/xtensa/core-fsf/xtensa-modules.inc.c
target/xtensa/core-sample_controller/core-isa.h
target/xtensa/core-sample_controller/xtensa-modules.inc.c
target/xtensa/core-test_kc705_be/core-isa.h
target/xtensa/core-test_kc705_be/xtensa-modules.inc.c
tests/tcg/cris/check_abs.c
tests/tcg/cris/check_addc.c
tests/tcg/cris/check_addcm.c
tests/tcg/cris/check_addoq.c
tests/tcg/cris/check_bound.c
tests/tcg/cris/check_ftag.c
tests/tcg/cris/check_int64.c
tests/tcg/cris/check_lz.c
tests/tcg/cris/check_openpf5.c
tests/tcg/cris/check_sigalrm.c
tests/tcg/cris/crisutils.h
tests/tcg/cris/sys.c
tests/tcg/i386/test-i386-ssse3.c
ui/vgafont.h
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20181213223737.11793-3-pbonzini@redhat.com>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Wainer dos Santos Moschetta <wainersm@redhat.com>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Eric Blake <eblake@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Stefan Markovic <smarkovic@wavecomp.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There are not many, and they are all simple mistakes that ended up
being committed. Remove them.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20181213223737.11793-2-pbonzini@redhat.com>
Reviewed-by: Wainer dos Santos Moschetta <wainersm@redhat.com>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Most list head structs need not be given a name. In most cases the
name is given just in case one is going to use QTAILQ_LAST, QTAILQ_PREV
or reverse iteration, but this does not apply to lists of other kinds,
and even for QTAILQ in practice this is only rarely needed. In addition,
we will soon reimplement those macros completely so that they do not
need a name for the head struct. So clean up everything, not giving a
name except in the rare case where it is necessary.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
usb packets with no payload (zero length) seem to happen in practice for
whatever reason. Add a check and skip the packet then, otherwise we'll
trigger an assert.
Reported-by: Leonardo Soares Müller <leozinho29_eu@hotmail.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20181211072649.20700-1-kraxel@redhat.com
This function is only needed when Q35 is in use. Moving it to
the same file that uses it lets you disable the entire USB
subsystem in x86_64-softmmu.mak; of course doing that will
cause -usb to break horribly, but one thing at a time.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1545064358-4601-1-git-send-email-pbonzini@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This patch introduces a new system bus generic EHCI controller.
For the system bus EHCI controller, we've already had "xlnx",
"exynos4210", "tegra2", "ppc4xx" and "fusbh200", they are specific and
only suitable for their own platforms, platforms such as an Arm server,
may need a generic system bus EHCI controller, this patch creates it,
and the kernel driver ehci_platform.c works well on it.
Signed-off-by: Hongbo Zhang <hongbo.zhang@linaro.org>
Message-id: 1546077657-22637-1-git-send-email-hongbo.zhang@linaro.org
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
In usb_device_post_load, certain values of dev->setup_len or
dev->setup_index can cause -EINVAL to be returned. One example is when
setup_len exceeds 4096, the hard-coded value of sizeof(dev->data_buf).
This can happen through legitimate guest activity and will cause all
subsequent attempts to migrate the guest to fail in vmstate_load_state.
The values of these variables can be set by USB packets originating in
the guest. There are two ways in which they can be set: in
do_token_setup and in do_parameter in hw/usb/core.c.
It is easy to craft a USB packet in a guest that causes do_token_setup
to set setup_len to a value larger than 4096. When this has been done
once, all subsequent attempts to migrate the VM will fail in
usb_device_post_load until the VM is next power-cycled or a
smaller-sized USB packet is sent to the device.
Sample code for achieving this in a VM started with "-device usb-tablet"
running Linux with CONFIG_HIDRAW=y and HID_MAX_BUFFER_SIZE > 4096:
#include <sys/types.h>
#include <sys/stat.h>
#include <fcntl.h>
#include <unistd.h>
int main() {
char buf[4097];
int fd = open("/dev/hidraw0", O_RDWR|O_NONBLOCK);
buf[0] = 0x1;
write(fd, buf, 4097);
return 0;
}
When this code is run in the VM, qemu will output:
usb_generic_handle_packet: ctrl buffer too small (4097 > 4096)
A subsequent attempt to migrate the VM will fail and output the
following on the destination host:
qemu-kvm: error while loading state for instance 0x0 of device '0000:00:06.7/1/usb-ptr'
qemu-kvm: load of migration failed: Invalid argument
The idea behind checking the values of setup_len and setup_index before
they are used is correct, but doing it in usb_device_post_load feels
arbitrary, and will cause unnecessary migration failures. Indeed, none
of the commit messages for c60174e8, 9f8e9895 and 719ffe1f justify why
post_load is the right place to do these checks. They correctly point
out that the important thing to protect is the usb_packet_copy.
Instead, the right place to do the checks is in do_token_setup and
do_parameter. Indeed, there are already some checks here. We can examine
each of the disjuncts currently tested in usb_device_post_load to see
whether any need adding to do_token_setup or do_parameter to improve
safety there:
* dev->setup_index < 0
- This test is not needed because setup_index is explicitly set to
0 in do_token_setup and do_parameter.
* dev->setup_len < 0
- In both do_token_setup and do_parameter, the value of setup_len
is computed by (s->setup_buf[7] << 8) | s->setup_buf[6]. Since
s->setup_buf is a byte array and setup_len is an int32_t, it's
impossible for this arithmetic to set setup_len's top bit, so it can
never be negative.
* dev->setup_index > dev->setup_len
- Since setup_index is 0, this is equivalent to the previous test,
so is redundant.
* dev->setup_len > sizeof(dev->data_buf)
- This condition is already explicitly checked in both
do_token_setup and do_parameter.
Hence there is no need to bolster the existing checks in do_token_setup
or do_parameter, and we can safely remove these checks from
usb_device_post_load without reducing safety but allowing migrations to
proceed regardless of what USB packets have been generated by the guest.
Signed-off-by: Jonathan Davies <jonathan.davies@nutanix.com>
Message-Id: <20190107175117.23769-1-jonathan.davies@nutanix.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
In previous commit:
commit 7dea29e4af
Author: Li Qiang <liq3ea@gmail.com>
Date: Fri Oct 19 03:50:36 2018 -0700
hw: ccid-card-emulated: cleanup resource when realize in error path
The emulated_realize method was changed so that it jumps to a cleanup
label to de-initialize state upon error. This change failed to ensure
the success path exited the method before this point though. So the
mutexes are always destroyed even in normal operation. The result is
as crashtastic as expected:
$ qemu-system-x86_64 -usb -device usb-ccid,id=ccid0 -device ccid-card-emulated,backend=nss-emulated,id=smartcard0,bus=ccid0.0
qemu-system-x86_64: util/qemu-thread-posix.c:64: qemu_mutex_lock_impl: Assertion `mutex->initialized' failed.
Aborted (core dumped)
Fixes: 7dea29e4af
Reported-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20181221134115.27973-1-berrange@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The filename length in MTP metadata is specified by the guest. By
trusting it directly it'd theoretically be possible to get the host to
write memory parts outside the filename buffer into a filename. In
practice though there are usually NUL bytes stopping the string
operations.
Also use the opportunity to not assign the filename member twice.
Signed-off-by: Michael Hanselmann <public@hansmi.ch>
Message-id: ab70659d8d5c580bdf150a5f7d5cc60c8e374ffc.1544740018.git.public@hansmi.ch
[ kraxel: codestyle fix: break a long line ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Open files and directories with O_NOFOLLOW to avoid symlinks attacks.
While being at it also add O_CLOEXEC.
usb-mtp only handles regular files and directories and ignores
everything else, so users should not see a difference.
Because qemu ignores symlinks, carrying out a successful symlink attack
requires swapping an existing file or directory below rootdir for a
symlink and winning the race against the inotify notification to qemu.
Fixes: CVE-2018-16872
Cc: Prasad J Pandit <ppandit@redhat.com>
Cc: Bandan Das <bsd@redhat.com>
Reported-by: Michael Hanselmann <public@hansmi.ch>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Michael Hanselmann <public@hansmi.ch>
Message-id: 20181213122511.13853-1-kraxel@redhat.com
Use DeviceClass rather than SysBusDeviceClass in
tusb6010_class_init().
Cc: kraxel@redhat.com
Signed-off-by: Mao Zhongyi <maozhongyi@cmss.chinamobile.com>
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Message-id: 20181130093852.20739-20-maozhongyi@cmss.chinamobile.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The token field contains the (guest-filled) state of the qtd, which
indicates whenever the other fields are valid or not. So make sure
we read the token first, otherwise we may end up with an stale next
pointer:
(1) ehci reads next
(2) guest writes next
(3) guest writes token
(4) ehci reads token
(5) ehci operates with stale next.
Typical effect is that qemu doesn't notice that the guest appends new
qtds to the end of the queue. Looks like the usb device stopped
responding. Linux can recover from that, but leaves a message in the
kernel log that it did reset the usb device in question.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20181126100836.8805-1-kraxel@redhat.com
we should perform these things as same as usb_host_close.
Signed-off-by: linzhecheng <linzhecheng@huawei.com>
Message-id: 20181130064700.5984-1-linzhecheng@huawei.com
[ kraxel: whitespace fixup ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Don't call xen_be_set_max_grant_refs() in usbback_alloc(), as the
gnttabdev pointer won't be initialised yet. The call can easily be
moved to usbback_connect().
Signed-off-by: Juergen Gross <jgross@suse.com>
Message-id: 20181206133923.30105-1-jgross@suse.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Slash is unix directory separator, so they are not allowed in filenames.
Note this also stops the classic escape via "../".
Fixes: CVE-2018-16867
Reported-by: Michael Hanselmann <public@hansmi.ch>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20181203101045.27976-3-kraxel@redhat.com
Make utf16_to_str return an allocated string. Remove the assumtion that
the number of string bytes equals the number of utf16 chars (which is
only true for ascii chars). Instead call wcstombs twice, once to figure
the storage size and once for the actual conversion (as suggested by the
wcstombs manpage).
FIXME: surrogate pairs are not working correctly. Pre-existing bug,
fixing that is left for another day.
Reported-by: Michael Hanselmann <public@hansmi.ch>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-id: 20181203101045.27976-2-kraxel@redhat.com
Because they are supposed to remain const.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20181114132931.22624-1-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If no kernel driver is active, we can already claim and perform I/O on
it without detaching it.
Signed-off-by: linzhecheng <linzhecheng@huawei.com>
Message-id: 20181120083419.17716-1-linzhecheng@huawei.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This can avoid setting OCHIState.num_ports to a negative num.
Signed-off-by: Li Qiang <liq3ea@gmail.com>
Message-id: 1540263618-18344-1-git-send-email-liq3ea@gmail.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
From include/qapi/error.h:
* Pass an existing error to the caller with the message modified:
* error_propagate(errp, err);
* error_prepend(errp, "Could not frobnicate '%s': ", name);
Fei Li pointed out that doing error_propagate() first doesn't work
well when @errp is &error_fatal or &error_abort: the error_prepend()
is never reached.
Since I doubt fixing the documentation will stop people from getting
it wrong, introduce error_propagate_prepend(), in the hope that it
lures people away from using its constituents in the wrong order.
Update the instructions in error.h accordingly.
Convert existing error_prepend() next to error_propagate to
error_propagate_prepend(). If any of these get reached with
&error_fatal or &error_abort, the error messages improve. I didn't
check whether that's the case anywhere.
Cc: Fei Li <fli@suse.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20181017082702.5581-2-armbru@redhat.com>
USB frame rate is slightly lower than 1kHz: ie. ~950Hz.
Thus usb-audio device is not able to perform a simple audio playback
without underruns on audio backend.
eg. "-device pci-ohci,id=ohci -device usb-audio,bus=ohci.0" vs PulseAudio
backend. more than 50 underruns are observed per second.
Update ohci_sof_time computation, using QEMU_CLOCK_VIRTUAL in
ohci_usb_start(), and increment by usb_frame_time in ohci_sof()
makes USB frame rate close to 1kHz.
This way, no audio underrun are observed during audio playback.
Signed-off-by: Miguel GAIO <mgaio35@gmail.com>
Message-Id: <20180927151936.3647-1-mgaio35@gmail.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Stale values in this field may result in qemu
expecting more data on the next operation
Signed-off-by: Bandan Das <bsd@redhat.com>
Message-id: 20180907220851.9658-4-bsd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Return STORE_FULL if we can't write all the bytes but
return incomplete transfer if data received is less then
what was specified in the metadata. Also, use d->offset
as the file size which is valid for all file sizes.
Signed-off-by: Bandan <bsd@redhat.com>
Message-id: 20180907220851.9658-2-bsd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
x-root was renamed as such owing to the experimental nature of the
property; the underlying filesystem semantics were undecided
Signed-off-by: Bandan Das <bsd@redhat.com>
Message-id: 20180720214020.22897-6-bsd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
To support larger file transfers, rely on a short packet
to detect end of the data phase and rewrite d->length to
the size received
Signed-off-by: Bandan Das <bsd@redhat.com>
Message-id: 20180720214020.22897-5-bsd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
For large buffers, write may not copy the full buffer. For example,
on Linux, write imposes a limit of 0x7ffff000. Note that this does
not fix >4G transfers but ~>2G files will transfer successfully.
Signed-off-by: Bandan Das <bsd@redhat.com>
Message-id: 20180720214020.22897-4-bsd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
usb_mtp_realloc() was being incorrectly used when allocating
buffer for incoming data. Set d->length only after resizing
the buffer.
Signed-off-by: Bandan Das <bsd@redhat.com>
Message-id: 20180720214020.22897-3-bsd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The initiator can choose to cancel an ongoing request which
is specified by bRequest=0x64. If such a request arrives,
free up any pending state
Signed-off-by: Bandan Das <bsd@redhat.com>
Message-id: 20180720214020.22897-2-bsd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This is mandated by the ohci specification. It tells at 6.4.4 on page 104
that for transfer descriptors that are retired with an error the done
queue interrupt counter is cleared as if the interrupt delay field of the
descriptions were zero.
Before this change, error conditions were handled similarly to the
successful condition which is especially troublesome for control transfers.
Some drivers (e.g., the AmigaOS-one) as well as the example code in the
spec, set the setup stage with an interrupt delay of seven (which means no
interrupt). This is fine under normal conditions, because one usually
doesn't want to be notified about the completion of this stage. However, if
an error occurs in this stage, these drivers will not get notified with the
current implementation. The fix addresses this by following the spec more
closely. Also, otherwise, the ability to set interrupt delay to seven would
be useless.
Note that Linux drivers that I looked at don't seem to be affected as they
set six as the interrupt delay presumably for the reason that they won't
get notified otherwise.
Signed-off-by: Sebastian Bauer <mail@sebastianbauer.info>
Message-id: 20180729191928.11254-1-mail@sebastianbauer.info
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This reinstates commit b008326744,
which was temporarily reverted for the 3.0 release so that libvirt gets
some extra time to update their command lines.
The -drive option serial was deprecated in QEMU 2.10. It's time to
remove it.
Tests need to be updated to set the serial number with -global instead
of using the -drive option.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
This reverts commit b008326744.
Hold off removing this for one more QEMU release (current libvirt
release still uses it.)
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Set xhci into error state instead of throwing a core dump.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20180702162752.29233-1-kraxel@redhat.com
Fetching qtd with the NULL address most likely makes no sense so from now
on, we handle it this case similarly as if the terminate (T) bit is not
set, which is already an exception as according to section 3.6 of the EHCI
spec there is no T bit defined for the current_qtd field.
The spec is a bit vague on how an EHCI driver should initialize these
fields: "The general operational model is that the host controller can
detect whether the overlay area contains a description of an active
transfer" (p. 49). QEMU primarily uses the QTD_TOKEN_ACTIVE bit of the
queue header to infer the activity state but there are other ways
conceivable.
This change allows QEMU to boot further into AmigaOS. The public available
version of the EHCI driver recycles queue heads in some rare conditions but
only clears the current_qtd field but not the status field. This works with
many available EHCI PCI cards but e.g., not with the Freescale USB
controller's found on the P5040. On the emulated EHCI controller of QEMU
the consequence is that some garbage was read in, which resulted in a
reset of the controller. This change fixes the problem.
Signed-off-by: Sebastian Bauer <mail@sebastianbauer.info>
Tested-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-id: 20180625222718.4488-1-mail@sebastianbauer.info
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
It eases code review, unit is explicit.
Patch generated using:
$ git grep -E '(1024|2048|4096|8192|(<<|>>).?(10|20|30))' hw/ include/hw/
and modified manually.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180625124238.25339-36-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The error handling policy was traditionally set with -drive, but with
-blockdev it is no longer possible to set frontend options. scsi-disk
(and other block devices) have long supported qdev properties to
configure the error handling policy, so let's add these options to
usb-storage as well and just forward them to the internal scsi-disk
instance.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
The USB device don't hold the bus. There is no ASAN related reports
anymore.
This reverts commit cd7bc87868.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20180613172815.32738-3-marcandre.lureau@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The bus is not owned by the device.
This reverts commit 410a096adf.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20180613172815.32738-2-marcandre.lureau@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The -drive option serial was deprecated in QEMU 2.10. It's time to
remove it.
Tests need to be updated to set the serial number with -global instead
of using the -drive option.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
We banned use of certain g_assert_FOO() functions outside tests, and
made checkpatch.pl flag them (commit 6e9389563e). We neglected to
purge existing uses. Do that now.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180608170231.27912-1-armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: John Snow <jsnow@redhat.com>
CID 1390604
If the initiator sends a packet with TYPE_DATA set without
initiating a CMD_GET_OBJECT_INFO first, then usb_mtp_get_data
can trip on a null s->data_out.
Signed-off-by: Bandan Das <bsd@redhat.com>
Message-Id: <jpgr2m8ajfk.fsf_-_@linux.bootlegged.copy>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
qbus_create_inplace() creates a new reference in realize(), it must be
released in unrealize().
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20180531195119.22021-4-marcandre.lureau@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
USB Specification Revision 2.0, §5.5.3:
The Data stage of a control transfer from an endpoint to the host is complete when the endpoint does one of the following:
• Has transferred exactly the amount of data specified during the Setup stage
• Transfers a packet with a payload size less than wMaxPacketSize or transfers a zero-length packet"
hw/usb/redirect.c:802:9: warning: Declared variable-length array (VLA) has zero size
uint8_t buf[size];
^~~~~~~~~~~ ~~~~
Reported-by: Clang Static Analyzer
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180604151421.23385-2-f4bug@amsat.org
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
vDPA support, fix to vhost blk RO bit handling, some include path
cleanups, NFIT ACPI table.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJbEXNvAAoJECgfDbjSjVRpc8gH/R8xrcFrV+k9wwbgYcOcGb6Y
LWjseE31pqJcxRV80vLOdzYEuLStZQKQQY7xBDMlA5vdyvZxIA6FLO2IsiJSbFAk
EK8pclwhpwQAahr8BfzenabohBv2UO7zu5+dqSvuJCiMWF3jGtPAIMxInfjXaOZY
odc1zY2D2EgsC7wZZ1hfraRbISBOiRaez9BoGDKPOyBY9G1ASEgxJgleFgoBLfsK
a1XU+fDM6hAVdxftfkTm0nibyf7PWPDyzqghLqjR9WXLvZP3Cqud4p8N29mY51pR
KSTjA4FYk6Z9EVMltyBHfdJs6RQzglKjxcNGdlrvacDfyFi79fGdiosVllrjfJM=
=3+V0
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
acpi, vhost, misc: fixes, features
vDPA support, fix to vhost blk RO bit handling, some include path
cleanups, NFIT ACPI table.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Fri 01 Jun 2018 17:25:19 BST
# gpg: using RSA key 281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (31 commits)
vhost-blk: turn on pre-defined RO feature bit
ACPI testing: test NFIT platform capabilities
nvdimm, acpi: support NFIT platform capabilities
tests/.gitignore: add entry for generated file
arch_init: sort architectures
ui: use local path for local headers
qga: use local path for local headers
colo: use local path for local headers
migration: use local path for local headers
usb: use local path for local headers
sd: fix up include
vhost-scsi: drop an unused include
ppc: use local path for local headers
rocker: drop an unused include
e1000e: use local path for local headers
ioapic: fix up includes
ide: use local path for local headers
display: use local path for local headers
trace: use local path for local headers
migration: drop an unused include
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When pulling in headers that are in the same directory as the C file (as
opposed to one in include/), we should use its relative path, without a
directory.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Remove those unneeded includes to speed up the compilation
process a little bit.
Code change produced with:
$ git grep '#include "sysemu/blockdev.h"' | \
cut -d: -f-1 | \
xargs egrep -L "(BlockInterfaceType|DriveInfo|drive_get|blk_legacy_dinfo|blockdev_mark_auto_del)" | \
xargs sed -i.bak '/#include "sysemu\/blockdev.h"/d'
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180528232719.4721-15-f4bug@amsat.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Now that helpers are available in xen_backend, use them throughout all
Xen PV backends.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Anthony Perard <anthony.perard@citrix.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
The current code was not correctly handling 64 B (Max USB 1.1 payload size)
packets and therefore preventing some of the messages from smart card to
pass through to the guest.
If the smart card in host responded with 34 B of data in APDU layer, the
CCID headers added up to 64 B. The packet was send, but not correctly
committed per USB specification (8.5.3.2 Variable-length Data Stage):
> When all of the data structure is returned to the host, the function
> should indicate that the Data stage is ended by returning a packet
> that is shorter than the MaxPacketSize for the pipe. If the data
> structure is an exact multiple of wMaxPacketSize for the pipe, the
> function will return a zero-length packet to indicate the end of the
> Data stage.
This lead the guest applications to timeout while waiting for the rest
of data (the emulation layer is answering with NAK until the timeout).
This patch is checking the current maximum packet size and if the
payload of this size is detected, the message buffer is not yet released.
With the next call, the empty buffer is sent and the message buffer
is finally released.
Signed-off-by: Jakub Jelen <jjelen@redhat.com>
Message-id: 20180516115544.3897-2-jjelen@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Since cc847bfd16, CCID card-passthru
fails to intialize, because it changed a debug line to an error,
probably by mistake. Change it back to a DPRINTF debug.
(solves Boxes creating VM with smartcard passthru failing to start)
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180515153039.27514-1-marcandre.lureau@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
usb-host emulates a device unplug after live migration, because the
device state is unknown and unplug/replug makes sure the guest
re-initializes the device into a working state. This can't be done in
post-load though, so post-load just schedules a bottom half which
executes after vmload is complete.
It can happen that the device autoscan timer hits the race window
between scheduling and running the bottom half, which in turn can
triggers an assert().
Fix that issue by just ignoring the usb_host_open() call in case the
bottom half didn't execute yet.
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1572851
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20180503062932.17233-1-kraxel@redhat.com
Currently, it's only being checked if desc is NULL and
so write support breaks upon specifying desc
Signed-off-by: Bandan Das <bsd@redhat.com>
Message-id: 20180503192028.14353-3-bsd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
CID 1390578: In usb_mtp_write_metadata, parent can never be NULL but
just in case, add an assert
CID 1390592: Check for o->format only if o !=NULL
CID 1390604: Check s->data_out != NULL in usb_mtp_handle_data
Signed-off-by: Bandan Das <bsd@redhat.com>
Message-id: 20180503192028.14353-2-bsd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Convert the tusb6010 device away from using the old_mmio field
of MemoryRegionOps. This device is used only in the n800 and n810
boards.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180427173611.10281-2-peter.maydell@linaro.org
Now that we can safely call QOBJECT() on QObject * as well as its
subtypes, we can have macros qobject_ref() / qobject_unref() that work
everywhere instead of having to use QINCREF() / QDECREF() for QObject
and qobject_incref() / qobject_decref() for its subtypes.
The replacement is mechanical, except I broke a long line, and added a
cast in monitor_qmp_cleanup_req_queue_locked(). Unlike
qobject_decref(), qobject_unref() doesn't accept void *.
Note that the new macros evaluate their argument exactly once, thus no
need to shout them.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20180419150145.24795-4-marcandre.lureau@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[Rebased, semantic conflict resolved, commit message improved]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
When trying to build with latest libcacard-2.5.1, I hit the
following error:
In file included from hw/usb/ccid-card-passthru.c:12:0:
/usr/include/cacard/vscard_common.h:26:2: error: #warning "Only <libcacard.h> can be included directly" [-Werror=cpp]
#warning "Only <libcacard.h> can be included directly"
While it was fixed in libcacard upstream (so that individual
files can be included directly), it doesn't make much sense.
Let's switch to including the main libcacard.h and also require
at least libcacard-2.5.1 which introduced it. It's available
since late 2015.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 3c36db1dc0702763ebb7966cc27428ed67d43804.1522751624.git.mprivozn@redhat.com
[ kraxel: fix include path ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
libusb-1.0.22 marked libusb_set_debug deprecated
it is replaced with
libusb_set_option(libusb_context, LIBUSB_OPTION_LOG_LEVEL, libusb_log_level);
details here: 539f22e2fd
Warning here:
CC hw/usb/host-libusb.o
/builds/xen/src/qemu-xen/hw/usb/host-libusb.c: In function 'usb_host_init':
/builds/xen/src/qemu-xen/hw/usb/host-libusb.c:250:5: error: 'libusb_set_debug' is deprecated: Use libusb_set_option instead [-Werror=deprecated-declarations]
libusb_set_debug(ctx, loglevel);
^~~~~~~~~~~~~~~~
In file included from /builds/xen/src/qemu-xen/hw/usb/host-libusb.c:40:0:
/usr/include/libusb-1.0/libusb.h:1300:18: note: declared here
void LIBUSB_CALL libusb_set_debug(libusb_context *ctx, int level);
^~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
make: *** [/builds/xen/src/qemu-xen/rules.mak:66: hw/usb/host-libusb.o] Error 1
make: Leaving directory '/builds/xen/src/xen/tools/qemu-xen-build'
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
Message-id: 20180405132046.4968-1-git@johnthomson.fastmail.com.au
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Commit d7d218ef02 attempted to change
dwProtocols to only advertise support for T=0 and not T=1. The change
was incorrect as it changed 0x00000003 to 0x00010000.
lsusb -v in a linux guest shows:
"dwProtocols 65536 (Invalid values detected)", though the
smart card could still be accessed. Windows 7 does not detect inserted
smart cards and logs the the following Error in the Event Logs:
Source: Smart Card Service
Event ID: 610
Smart Card Reader 'QEMU QEMU USB CCID 0' rejected IOCTL SET_PROTOCOL:
Incorrect function. If this error persists, your smart card or reader
may not be functioning correctly
Command Header: 03 00 00 00
Setting to 0x00000001 fixes the Windows issue.
Signed-off-by: Jason Andryuk <jandryuk@gmail.com>
Message-id: 20180420183219.20722-1-jandryuk@gmail.com
Cc: qemu-stable@nongnu.org
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Changing the current ordering saves 8 bytes per entry in x86_64.
Signed-off-by: zhenwei.pi <zhenwei.pi@youruncloud.com>
Message-id: 1520318781-22644-1-git-send-email-zhenwei.pi@youruncloud.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This patch implements a dummy ObjectInfo structure so that
it's easy to typecast the incoming data. If the metadata is
valid, write_pending is set. Also, the incoming filename
is utf-16, so, instead of depending on external libraries, just
implement a simple function to get the filename
Signed-off-by: Bandan Das <bsd@redhat.com>
Message-id: 20180223164829.29683-6-bsd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Allow write operations on behalf of the initiator. The
precursor to write is the sending of the write metadata
that consists of the ObjectInfo dataset. This patch introduces
a flag that is set when the responder is ready to receive
write data based on a previous SendObjectInfo operation by
the initiator (The SendObjectInfo implementation is in a
later patch)
Signed-off-by: Bandan Das <bsd@redhat.com>
Message-id: 20180223164829.29683-5-bsd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Write of existing objects by the initiator is acheived by
making a temporary buffer with the new changes, deleting the
old file and then writing a new file with the same name.
Also, add a "readonly" property which needs to be set to false
for deletion to work.
Signed-off-by: Bandan Das <bsd@redhat.com>
Message-id: 20180223164829.29683-4-bsd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Fix a possible null dereference when deleting a folder and
its contents. An ignored event might be received for its contents
after the parent folder is deleted which will return a null object.
Signed-off-by: Bandan Das <bsd@redhat.com>
Message-id: 20180223164829.29683-3-bsd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The response to a SendObjectInfo consists of the storageid,
parent obejct handle and the handle reserved for the new
incoming object
Signed-off-by: Bandan Das <bsd@redhat.com>
Message-id: 20180223164829.29683-2-bsd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
- new stats in virtio balloon
- virtio eventfd rework for boot speedup
- vhost memory rework for boot speedup
- fixes and cleanups all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJagxKDAAoJECgfDbjSjVRp5qAH/3gmgBaIzL3KRHd5i0RZifJv
PvyAVYgZd7h0+/1r9GM7guHKyEPZ08JtbHSm/HuDV4BD/Vf3/8joy8roExIfde2A
6k8fd6ANVQmE3t5zUxNXi9qiG4pO4xDIu4cMAbixzgN9x5ttlcfTw7fTT0e0VJxJ
8SN02/uCPPR/DY4/cpjah+slSyv6rBKT1v1ONy7djyRTYHi6h3Meoh05YfEALkwA
goxTKBZHi0L1IZ3HP/ZpXJDohQ5n2P09DX0fQgb8PgmW6WIWB/Qpi5pD53LZpMCV
n9waTF0U0ahneFd2FHo22QMMrwWvQyrjv+w5uXVr+qmHb/OyH2tUt7PgGF9+QKA=
=78s5
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
virtio,vhost,pci,pc: features, fixes and cleanups
- new stats in virtio balloon
- virtio eventfd rework for boot speedup
- vhost memory rework for boot speedup
- fixes and cleanups all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Tue 13 Feb 2018 16:29:55 GMT
# gpg: using RSA key 281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (22 commits)
virtio-balloon: include statistics of disk/file caches
acpi-test: update FADT
lpc: drop pcie host dependency
tests: acpi: fix FADT not being compared to reference table
hw/pci-bridge: fix pcie root port's IO hints capability
libvhost-user: Support across-memory-boundary access
libvhost-user: Fix resource leak
virtio-balloon: unref the memory region before continuing
pci: removed the is_express field since a uniform interface was inserted
virtio-blk: enable multiple vectors when using multiple I/O queues
pci/bus: let it has higher migration priority
pci-bridge/i82801b11: clear bridge registers on platform reset
vhost: Move log_dirty check
vhost: Merge and delete unused callbacks
vhost: Clean out old vhost_set_memory and friends
vhost: Regenerate region list from changed sections list
vhost: Merge sections added to temporary list
vhost: Simplify ring verification checks
vhost: Build temporary section list and deref after commit
virtio: improve virtio devices initialization time
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
-----BEGIN PGP SIGNATURE-----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=DMbf
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/armbru/tags/pull-misc-2018-02-07-v4' into staging
Miscellaneous patches for 2018-02-07
# gpg: Signature made Fri 09 Feb 2018 12:52:51 GMT
# gpg: using RSA key 3870B400EB918653
# gpg: Good signature from "Markus Armbruster <armbru@redhat.com>"
# gpg: aka "Markus Armbruster <armbru@pond.sub.org>"
# Primary key fingerprint: 354B C8B3 D7EB 2A6B 6867 4E5F 3870 B400 EB91 8653
* remotes/armbru/tags/pull-misc-2018-02-07-v4:
Move include qemu/option.h from qemu-common.h to actual users
Drop superfluous includes of qapi/qmp/qjson.h
Drop superfluous includes of qapi/qmp/dispatch.h
Include qapi/qmp/qnull.h exactly where needed
Include qapi/qmp/qnum.h exactly where needed
Include qapi/qmp/qbool.h exactly where needed
Include qapi/qmp/qstring.h exactly where needed
Include qapi/qmp/qdict.h exactly where needed
Include qapi/qmp/qlist.h exactly where needed
Include qapi/qmp/qobject.h exactly where needed
qdict qlist: Make most helper macros functions
Eliminate qapi/qmp/types.h
Typedef the subtypes of QObject in qemu/typedefs.h, too
Include qmp-commands.h exactly where needed
Drop superfluous includes of qapi/qmp/qerror.h
Include qapi/error.h exactly where needed
Drop superfluous includes of qapi-types.h and test-qapi-types.h
Clean up includes
Use #include "..." for our own headers, <...> for others
vnc: use stubs for CONFIG_VNC=n dummy functions
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
qemu-common.h includes qemu/option.h, but most places that include the
former don't actually need the latter. Drop the include, and add it
to the places that actually need it.
While there, drop superfluous includes of both headers, and
separate #include from file comment with a blank line.
This cleanup makes the number of objects depending on qemu/option.h
drop from 4545 (out of 4743) to 284 in my "build everything" tree.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180201111846.21846-20-armbru@redhat.com>
[Semantic conflict with commit bdd6a90a9e in block/nvme.c resolved]
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180201111846.21846-15-armbru@redhat.com>
This cleanup makes the number of objects depending on qapi/qmp/qdict.h
drop from 4550 (out of 4743) to 368 in my "build everything" tree.
For qapi/qmp/qobject.h, the number drops from 4552 to 390.
While there, separate #include from file comment with a blank line.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180201111846.21846-13-armbru@redhat.com>
This cleanup makes the number of objects depending on qapi/error.h
drop from 1910 (out of 4743) to 1612 in my "build everything" tree.
While there, separate #include from file comment with a blank line,
and drop a useless comment on why qemu/osdep.h is included first.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180201111846.21846-5-armbru@redhat.com>
[Semantic conflict with commit 34e304e975 resolved, OSX breakage fixed]
Add code to emulate Chipidea USB IP (used in i.MX SoCs). Tested to
work against:
-usb -drive if=none,id=stick,file=usb.img,format=raw -device \
usb-storage,bus=usb-bus.0,drive=stick
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Philippe Mathieu-Daudé <f4bug@amsat.org>
Cc: Marcel Apfelbaum <marcel.apfelbaum@zoho.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: qemu-devel@nongnu.org
Cc: qemu-arm@nongnu.org
Cc: yurovsky@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
according to Eduardo Habkost's commit fd3b02c889 all PCIEs now implement
INTERFACE_PCIE_DEVICE so we don't need is_express field anymore.
Devices that implements only INTERFACE_PCIE_DEVICE (is_express == 1)
or
devices that implements only INTERFACE_CONVENTIONAL_PCI_DEVICE (is_express == 0)
where not affected by the change.
The only devices that were affected are those that are hybrid and also
had (is_express == 1) - therefor only:
- hw/vfio/pci.c
- hw/usb/hcd-xhci.c
- hw/xen/xen_pt.c
For those 3 I made sure that QEMU_PCI_CAP_EXPRESS is on in instance_init()
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Yoni Bettan <ybettan@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Replace init() of CCIDCardClass with realize, then convert
ccid_card_init(), ccid_card_initfn() and it's callbacks to
take an Error** in ordor to report the error more clearly.
Signed-off-by: Mao Zhongyi <maozy.fnst@cn.fujitsu.com>
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180125171432.13554-2-f4bug@amsat.org
[PMD: fixed s->card assignation in ccid_card_realize()]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Because usb-storage creates an internal scsi device, we should propagate
options. We already do so for bootindex etc, but failed to take care of
share-rw. Fix it in an apparent way: add a new parameter to
scsi_bus_legacy_add_drive and pass in s->conf.share_rw.
Cc: qemu-stable@nongnu.org
Signed-off-by: Fam Zheng <famz@redhat.com>
Reviewed-by: Darren Kenny <darren.kenny@oracle.com>
Message-id: 20180117005222.4781-1-famz@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The option have been marked as deprecated since QEMU 2.10, and so far
nobody complained that the host, serial, disk and net options are urgently
required anymore. So let's now get rid at least of this legacy pile, to
simplify the usb code quite a bit.
This patch removes the usbdevices host, serial, disk and net. These devices
use their own complicated parameter parsing mechanisms, so they are just
ugly to maintain, without real benefit for the users (the users can use the
corresponding "-device" parameters instead which have the same complexity
as the "-usbdevice" devices here).
Note that the other rather simple -usbdevice options (mouse, tablet, etc.)
are not removed yet (the code is really simple here, so it does not hurt
much to keep it), as well as the two devices "braille" and "bt" which are
easier to use with -usbdevice than with -device.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-id: 1515519171-20315-1-git-send-email-thuth@redhat.com
[kraxel] delete some usb_host_device_open() leftovers.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Replace all occurs of __FUNCTION__ except for the check in checkpatch
with the non GCC specific __func__.
One line in hcd-musb.c was manually tweaked to pass checkpatch.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
[THH: Removed hunks related to pxa2xx_mmci.c (fixed already)]
Signed-off-by: Thomas Huth <thuth@redhat.com>
The function name of usb_msd_{realize,unrealize}_*,
usb_msd_class_initfn_* are unusual. Rename it to
usb_msd_*_{realize,unrealize}, usb_msd_class_*_initfn.
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Mao Zhongyi <maozy.fnst@cn.fujitsu.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 11e6003433abce35f3f4970e1acc71ee92dbcf51.1511317952.git.maozy.fnst@cn.fujitsu.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
[Drop virtio_blk_data_plane_create() change that misinterprets return
value when the virtio transport does not support dataplane.
--Stefan]
Cc: John Snow <jsnow@redhat.com>
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: Max Reitz <mreitz@redhat.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Mao Zhongyi <maozy.fnst@cn.fujitsu.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: e77848d3735ba590f23ffbf8094379c646c33d79.1511317952.git.maozy.fnst@cn.fujitsu.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
It's easy to use device_add and device_del as replacement instead.
The usb_add and usb_del commands are deprecated since QEMU 2.10,
and nobody complained that they are still needed, so let's get rid
of them now to make the HMP interface a little bit less overloaded.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1512073140-17672-1-git-send-email-thuth@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Philippe Mathieu-Daudé
Gerd Hoffmann
Daniel P. Berrangé
Thomas Huth
Longpeng
Bandan Das
Peter Maydell
Laurent Vivier
Markus Armbruster
Kővágó, Zoltán
Paolo Bonzini
Alexander Kappner
Liam Merwick
Michael Roth
Yuri Benditovich
Li Qiang
Paul Durrant
Hongbo Zhang
Jonathan Davies
Michael Hanselmann
Mao Zhongyi
linzhecheng
Juergen Gross
Marc-André Lureau
Li Qiang
Miguel GAIO
Sebastian Bauer
Kevin Wolf
Cornelia Huck
Philippe Mathieu-Daudé
Michael S. Tsirkin
Jakub Jelen
Michal Privoznik
John Thomson
Jason Andryuk
zhenwei.pi
Andrey Smirnov
Yoni Bettan
Mao Zhongyi
Fam Zheng
Alistair Francis