Add a bootloader helper to generate simple bootloaders for kernel.
It can help us reduce inline hex hack and also keep MIPS release 6
compatibility easier.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210127065424.114125-2-jiaxun.yang@flygoat.com>
[PMD: Restricted bl_reg enum to C source,
inverted bl_gen_write() args,
added license in hw/mips/bootloader.h]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
There is already a MemMapEntry type defined in hwaddr.h. Let's drop
the loongson3 defined `struct MemmapEntry` and use the existing one.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210122122404.11970-1-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
s->prnsts is updated in both branches of the if () else () statement.
Move the common bits outside so that it is cleaner.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Reviewed-by: Alexander Bulekov <alxndr@bu.edu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1613447214-81951-5-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Unlike SD mode, when SD card is working in SPI mode, the argument
of CMD13 is stuff bits. Hence we should bypass the RCA check.
See "Physical Layer Specification Version 8.00", chapter 7.3.1.3
Detailed Command Description (SPI mode):
"The card shall ignore stuff bits and reserved bits in an argument"
and Table 7-3 Commands and Arguments (SPI mode):
"CMD13 Argument [31:0] stuff bits"
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210216150225.27996-9-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
High capacity cards don't support write protection hence we should
not perform the write protect groups check in CMD24/25 for them.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210216150225.27996-8-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
High capacity cards don't support write protection hence we should
not perform the write protect groups check in sd_erase() for them.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210216150225.27996-6-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
These APIs and macros may be referenced by functions that are
currently before them. Move them ahead a little bit.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210216150225.27996-5-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Per the "Physical Layer Specification Version 8.00", table 4-26
(SD mode) and table 7-3 (SPI mode) command descriptions, CMD30
response type is R1, not R1b.
Fixes: a1bb27b1e9 ("SD card emulation initial implementation")
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210216150225.27996-4-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Per the "Physical Layer Specification Version 8.00", table 4-26
(SD mode) and table 7-3 (SPI mode) command descriptions, the
following commands:
- CMD28 (SET_WRITE_PROT)
- CMD29 (CLR_WRITE_PROT)
- CMD30 (SEND_WRITE_PROT)
are only supported by SDSC cards.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210216150225.27996-3-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
For high capacity memory cards, the erase start address and end
address are multiplied by 512, but the address check is still
based on the original block number in sd->erase_{start, end}.
Fixes: 1bd6fd8ed5 ("hw/sd/sdcard: Do not attempt to erase out of range addresses")
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210216150225.27996-2-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Besides CMD12, the following command's reponse type is R1b:
- SET_WRITE_PROT (CMD28)
- CLR_WRITE_PROT (CMD29)
- ERASE (CMD38)
Reuse the same s->stopping to indicate a R1b reponse is needed.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210128063035.15674-10-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
CMD12's response type is R1b, which is basically a R1 plus optional
addition of the busy signal token that can be any number of bytes.
A zero value indicates card is busy and a non-zero value indicates
the card is ready for the next command.
Current implementation sends the busy signal token without sending
the R1 first. This does not break the U-Boot/Linux mmc_spi driver,
but it does not make the VxWorks driver happy.
Move the testing logic of s->stopping in the SSI_SD_RESPONSE state
a bit later, after the first byte of the card reponse is sent out,
to conform with the spec. After the busy signal token is sent, the
state should be transferred to SSI_SD_CMD.
Fixes: 775616c3ae ("Partial SD card SPI mode support")
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Message-Id: <20210128063035.15674-9-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The SEND_IF_COND command (CMD8) response is of format R7, but
current code returns R1 for CMD8. Fix it.
Fixes: 775616c3ae ("Partial SD card SPI mode support")
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210128063035.15674-8-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
For a multiple block write operation, each block begins with a multi
write start token. Unlike the SD mode that the multiple block write
ends when receiving a STOP_TRAN command (CMD12), a special stop tran
token is used to signal the card.
Emulating this by manually sending a CMD12 to the SD card core, to
bring it out of the receiving data state.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20210128063035.15674-7-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Add 2 more states for the block write operation. The SPI host needs
to send a data start token to start the transfer, and the data block
written to the card will be acknowledged by a data response token.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
[PMD: Change VMState version id 6 -> 7]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20210128063035.15674-6-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
At present there is a data_ready() callback for the SD data read
path. Let's add a receive_ready() for the SD data write path.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20210128063035.15674-5-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
At present the single/multiple block write in SPI mode is blocked
by sd_normal_command(). Remove the limitation.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210128063035.15674-4-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The single block read (CMD17) codes are the same as the multiple
block read (CMD18). Merge them into one. The same applies to single
block write (CMD24) and multiple block write (CMD25).
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20210128063035.15674-3-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
In the case of a multiple block read operation every transferred
block has its suffix of CRC16. Update the state machine logic to
handle multiple block read.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
[PMD: Change VMState version id 5 -> 6]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20210128063035.15674-2-bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
When viewing/debugging memory regions it is sometimes hard to figure
out which PCI device something belongs to. Make the names unique by
including the vdev name in the name string.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20210213130325.14781-2-alex.bennee@linaro.org>
Without that wireshark complains about invalid control setup data
for non-control transfers.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20210216144939.841873-1-kraxel@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
In order to keep track of the alternate setting that should be used for
a given interface, the USBDevice struct keeps an array of alternate
setting values, which is indexed by the interface number. In
usb_host_set_interface, when this array is updated, usb_host_ep_update
is called as a result. However, when usb_host_ep_update accesses the
active libusb_config_descriptor, it indexes udev->altsetting with the
loop variable, rather than the interface number.
With the simple trace backend enable, this behavior can be seen:
[...]
usb_xhci_xfer_start 0.440 pid=1215 xfer=0x5596a4b85930 slotid=0x1 epid=0x1 streamid=0x0
usb_packet_state_change 1.703 pid=1215 bus=0x1 port=b'1' ep=0x0 p=0x5596a4b85938 o=b'undef' n=b'setup'
usb_host_req_control 2.269 pid=1215 bus=0x1 addr=0x5 p=0x5596a4b85938 req=0x10b value=0x1 index=0xd
usb_host_set_interface 0.449 pid=1215 bus=0x1 addr=0x5 interface=0xd alt=0x1
usb_host_parse_config 2542.648 pid=1215 bus=0x1 addr=0x5 value=0x2 active=0x1
usb_host_parse_interface 1.804 pid=1215 bus=0x1 addr=0x5 num=0xc alt=0x0 active=0x1
usb_host_parse_endpoint 2.012 pid=1215 bus=0x1 addr=0x5 ep=0x2 dir=b'in' type=b'int' active=0x1
usb_host_parse_interface 1.598 pid=1215 bus=0x1 addr=0x5 num=0xd alt=0x0 active=0x1
usb_host_req_emulated 3.593 pid=1215 bus=0x1 addr=0x5 p=0x5596a4b85938 status=0x0
usb_packet_state_change 2.550 pid=1215 bus=0x1 port=b'1' ep=0x0 p=0x5596a4b85938 o=b'setup' n=b'complete'
usb_xhci_xfer_success 4.298 pid=1215 xfer=0x5596a4b85930 bytes=0x0
[...]
In particular, it is seen that although usb_host_set_interface sets the
alternate setting of interface 0xd to 0x1, usb_host_ep_update uses 0x0
as the alternate setting due to using the incorrect index to
udev->altsetting.
Fix this problem by getting the interface number from the active
libusb_config_descriptor, and then using that as the index to
udev->altsetting.
Signed-off-by: Nick Rosbrook <rosbrookn@ainfosec.com>
Message-Id: <20210201213021.500277-1-rosbrookn@ainfosec.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
When SEV-ES is enabled, it is not possible modify the guests register
state after it has been initially created, encrypted and measured.
Normally, an INIT-SIPI-SIPI request is used to boot the AP. However, the
hypervisor cannot emulate this because it cannot update the AP register
state. For the very first boot by an AP, the reset vector CS segment
value and the EIP value must be programmed before the register has been
encrypted and measured. Search the guest firmware for the guest for a
specific GUID that tells Qemu the value of the reset vector to use.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Cc: Richard Henderson <richard.henderson@linaro.org>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Message-Id: <22db2bfb4d6551aed661a9ae95b4fdbef613ca21.1611682609.git.thomas.lendacky@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
OVMF is developing a mechanism for depositing a GUIDed table just
below the known location of the reset vector. The table goes
backwards in memory so all entries are of the form
<data>|len|<GUID>
Where <data> is arbtrary size and type, <len> is a uint16_t and
describes the entire length of the entry from the beginning of the
data to the end of the guid.
The foot of the table is of this form and <len> for this case
describes the entire size of the table. The table foot GUID is
defined by OVMF as 96b582de-1fb2-45f7-baea-a366c55a082d and if the
table is present this GUID is just below the reset vector, 48 bytes
before the end of the firmware file.
Add a parser for the ovmf reset block which takes a copy of the block,
if the table foot guid is found, minus the footer and a function for
later traversal to return the data area of any specified GUIDs.
Signed-off-by: James Bottomley <jejb@linux.ibm.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20210204193939.16617-2-jejb@linux.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch implements the FIFO mode of the SMBus module. In FIFO, the
user transmits or receives at most 16 bytes at a time. The FIFO mode
allows the module to transmit large amount of data faster than single
byte mode.
Since we only added the device in a patch that is only a few commits
away in the same patch set. We do not increase the VMstate version
number in this special case.
Reviewed-by: Doug Evans<dje@google.com>
Reviewed-by: Tyrong Ting<kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Message-id: 20210210220426.3577804-6-wuhaotsh@google.com
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This commit implements the single-byte mode of the SMBus.
Each Nuvoton SoC has 16 System Management Bus (SMBus). These buses
compliant with SMBus and I2C protocol.
This patch implements the single-byte mode of the SMBus. In this mode,
the user sends or receives a byte each time. The SMBus device transmits
it to the underlying i2c device and sends an interrupt back to the QEMU
guest.
Reviewed-by: Doug Evans<dje@google.com>
Reviewed-by: Tyrong Ting<kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Message-id: 20210210220426.3577804-2-wuhaotsh@google.com
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Linux blkfront expects both "discard-granularity" and
"discard-alignment" present on xenbus in order to properly enable the
feature, not exposing "discard-alignment" left some Linux blkfront
versions with a broken discard setup. This has also been addressed in
Linux with:
https://lore.kernel.org/lkml/20210118151528.81668-1-roger.pau@citrix.com/T/#u
Fix QEMU to report a "discard-alignment" of 0, in order for it to work
with older Linux frontends.
Reported-by: Arthur Borsboom <arthurborsboom@gmail.com>
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Message-Id: <20210118153330.82324-1-roger.pau@citrix.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
cmd_fis is mapped as DMA_DIRECTION_FROM_DEVICE, however, it is read
from, and not written to anywhere. Fix the DMA_DIRECTION and mark
cmd_fis as read-only in the code.
Signed-off-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20210119164051.89268-1-alxndr@bu.edu>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Copy bootinfo.h and bootinfo-mac.h from arch/m68k/include/uapi/asm/
to include/standard-headers/asm-m68k/
Imported from linux v5.9 but didn't change since v4.14 (header update)
and since v4.10 (content update).
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20201220112615.933036-2-laurent@vivier.eu>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Use nr_apu_cpus in favor of hard coding 2.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-id: 20210210142048.3125878-2-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
nvme_ns_realize passes errp to nvme_register_namespaces, but then try to
prepend errp with local_err.
Just remove the local_err and use errp directly.
Fixes: 15d024d4aa ("hw/block/nvme: split setup and register for namespace")
Cc: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Current QEMU HEAD nvme.c does not compile with the default GCC 5.4
on a Ubuntu 16.04 host:
hw/block/nvme.c:3242:9: error: ‘result’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
trace_pci_nvme_getfeat_vwcache(result ? "enabled" : "disabled");
^
hw/block/nvme.c:3150:14: note: ‘result’ was declared here
uint32_t result;
^
Explicitly initialize the result to fix it.
Fixes: aa5e55e3b0 ("hw/block/nvme: open code for volatile write cache")
Fixes: Coverity CID 1446371
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Moving namespace registration to the nvme-ns realization function had
the unintended side-effect of breaking legacy namespace registration.
Fix this.
Fixes: 15d024d4aa ("hw/block/nvme: split setup and register for namespace")
Reported-by: Alexander Graf <agraf@csgraf.de>
Cc: Minwoo Im <minwoo.im.dev@gmail.com>
Tested-by: Alexander Graf <agraf@csgraf.de>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Update infocenter.arm.com URLs for various pieces of Arm
documentation to the new developer.arm.com equivalents. (There is a
redirection in place from the old URLs, but we might as well update
our comments in case the redirect ever disappears in future.)
This patch covers all the URLs which are not MPS2/SSE-200/IoTKit
related (those are dealt with in a different patch).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210205171456.19939-1-peter.maydell@linaro.org
NPCM7XX GPIO devices have been implemented in hw/gpio/npcm7xx-gpio.c. So
we removed them from the unimplemented devices list.
Reviewed-by: Doug Evans<dje@google.com>
Reviewed-by: Tyrong Ting<kfting@nuvoton.com>
Signed-off-by: Hao Wu<wuhaotsh@google.com>
Message-id: 20210129005845.416272-2-wuhaotsh@google.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Perform device reset in the remote process when QEMU performs
device reset. This is required to reset the internal state
(like registers, etc...) of emulated devices
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 7cb220a51f565dc0817bd76e2f540e89c2d2b850.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Retrieve PCI configuration info about the remote device and
configure the Proxy PCI object based on the returned information
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 85ee367bbb993aa23699b44cfedd83b4ea6d5221.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
IOHUB object is added to manage PCI IRQs. It uses KVM_IRQFD
ioctl to create irqfd to injecting PCI interrupts to the guest.
IOHUB object forwards the irqfd to the remote process. Remote process
uses this fd to directly send interrupts to the guest, bypassing QEMU.
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 51d5c3d54e28a68b002e3875c59599c9f5a424a1.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Add ProxyMemoryListener object which is used to keep the view of the RAM
in sync between QEMU and remote process.
A MemoryListener is registered for system-memory AddressSpace. The
listener sends SYNC_SYSMEM message to the remote process when memory
listener commits the changes to memory, the remote process receives
the message and processes it in the handler for SYNC_SYSMEM message.
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 04fe4e6a9ca90d4f11ab6f59be7652f5b086a071.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Proxy device object implements handler for PCI BAR writes and reads.
The handler uses BAR_WRITE/BAR_READ message to communicate to the
remote process with the BAR address and value to be written/read.
The remote process implements handler for BAR_WRITE/BAR_READ
message.
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: a8b76714a9688be5552c4c92d089bc9e8a4707ff.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The Proxy Object sends the PCI config space accesses as messages
to the remote process over the communication channel
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: d3c94f4618813234655356c60e6f0d0362ff42d6.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: d54edb4176361eed86b903e8f27058363b6c83b3.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Defines a PCI Device proxy object as a child of TYPE_PCI_DEVICE.
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: b5186ebfedf8e557044d09a768846c59230ad3a7.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
