Tests the following for both P9 and P10:
- I2C master POR status
- I2C master status after immediate reset
Tests the following for powernv10-ranier only:
- Config pca9552 hotplug device pins as inputs then
Read the INPUT0/1 registers to verify all pins are high
- Connected GPIO pin tests of P10 PCA9552 device. Tests
output of pins 0-4 affect input of pins 5-9 respectively.
- PCA9554 GPIO pins test. Tests input and ouput functionality.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Glenn Miles <milesg@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Specs are available here:
https://www.nxp.com/docs/en/data-sheet/PCA9554_9554A.pdf
This is a simple model supporting the basic registers for GPIO
mode. The device also supports an interrupt output line but the
model does not yet support this.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Glenn Miles <milesg@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
The Power Hypervisor code expects to see a pca9552 device connected
to the 3rd PNV I2C engine on port 1 at I2C address 0x63 (or left-
justified address of 0xC6). This is used by hypervisor code to
control PCIe slot power during hotplug events.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Glenn Miles <milesg@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Allow external devices to drive pca9552 input pins by adding
input GPIO's to the model. This allows a device to connect
its output GPIO's to the pca9552 input GPIO's.
In order for an external device to set the state of a pca9552
pin, the pin must first be configured for high impedance (LED
is off). If the pca9552 pin is configured to drive the pin low
(LED is on), then external input will be ignored.
Here is a table describing the logical state of a pca9552 pin
given the state being driven by the pca9552 and an external device:
PCA9552
Configured
State
| Hi-Z | Low |
------+------+-----+
External Hi-Z | Hi | Low |
Device ------+------+-----+
State Low | Low | Low |
------+------+-----+
Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Signed-off-by: Glenn Miles <milesg@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
spapr_irq_init currently uses existing macro SPAPR_XIRQ_BASE to refer to
the range of CPU IPIs during initialization of nr-irqs property.
It is more appropriate to have its own define which can be further
reused as appropriate for correct interpretation.
Suggested-by: Cedric Le Goater <clg@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Kowshik Jois <kowsjois@linux.ibm.com>
Signed-off-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Since 'softmmu' is quite a loaded term in QEMU, rename the vhyp MMU
facilities to use the vhyp_mmu_ prefix rather than softmmu_.
vhyp_mmu_ is chosen because the code that manipulates the hash table
via guest software hypercalls is QEMU's implementation of the PAPR
hypervisor interface, called vhyp.
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
[npiggin: Pick a different name, explain it in changelog.]
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
- Remove sysbus_add_io (Phil)
- Build PPC 4xx PCI host bridges once (Phil)
- Display QOM path while debugging SMBus targets (Joe)
- Simplify x86 PC code (Bernhard)
- Remove qemu_[un]register_reset() calls in x86 PC CMOS (Peter)
- Fix wiring of ICH9 LPC interrupts (Bernhard)
- Split core IDE as device / bus / dma (Thomas)
- Prefer QDev API over QOM for devices (Phil)
- Fix invalid use of DO_UPCAST() in Leon3 (Thomas)
-----BEGIN PGP SIGNATURE-----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=+h2O
-----END PGP SIGNATURE-----
Merge tag 'hw-misc-20240222' of https://github.com/philmd/qemu into staging
Misc HW patch queue
- Remove sysbus_add_io (Phil)
- Build PPC 4xx PCI host bridges once (Phil)
- Display QOM path while debugging SMBus targets (Joe)
- Simplify x86 PC code (Bernhard)
- Remove qemu_[un]register_reset() calls in x86 PC CMOS (Peter)
- Fix wiring of ICH9 LPC interrupts (Bernhard)
- Split core IDE as device / bus / dma (Thomas)
- Prefer QDev API over QOM for devices (Phil)
- Fix invalid use of DO_UPCAST() in Leon3 (Thomas)
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEE+qvnXhKRciHc/Wuy4+MsLN6twN4FAmXXQ1IACgkQ4+MsLN6t
# wN4e2xAAig55EJh/JwpdGx55rFUab3Ay22jgXrExmBir8hzhyzssY+RUj2ALRa5e
# T26kxCEqiuT549FtWm/ci6kVax0QD6bqz/6/j451XB9469Z/3BDOV5rhsqF6zlr5
# BMbyC8PKnMUluG8v1ZuRjC3m2lK3ZvkVnZtj7SZUR50ssEnR32fVIziN14/OYkts
# 2B24sLrnLBfvyatMRsuFqGWrcbtMdnwNpjenGfDPOTF33W1sxTQ8GSvx1RV32l69
# Yr/iCVoCl+rGxbLLP1TwqtOwzk32p8RsbIt6rWMqVMv/p5F6ezFeiOk7VHnnEJRH
# e7TPxt4XeLGPARMQLT3gQh0MGIIodanSHePRBkczuNmKYTJrz+5jMu2Qg4MmMUE/
# TV0fKgdjh/edhAOHzJgZqLmNV71icl8WBjfsw2qT4ZwgJzWq7YM2/XZKkeWhk2nQ
# whLxfgiU4PNJ6vHhebJNjOovCYQTK2FbXR+PvVn5FEbH4CuFr8mqkYc+vNYM9dLA
# b7uMk1H8kcb5+kqfPPU2lVd1wO7uqhxYOYU2O9nYq8aw7ioLoLeEdj2IicLtrA/H
# GMtyA5cYeabeRzSXF30tM2AR1uQ/e4Z7oNxW6z3GVK1NrQtKilqPgMKut8uWYvva
# crJLpRQhGiY3sDrIkkCcAHzv256dZaJNLR1KPViaHOyVPZV+x2s=
# =+h2O
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 22 Feb 2024 12:51:30 GMT
# gpg: using RSA key FAABE75E12917221DCFD6BB2E3E32C2CDEADC0DE
# gpg: Good signature from "Philippe Mathieu-Daudé (F4BUG) <f4bug@amsat.org>" [full]
# Primary key fingerprint: FAAB E75E 1291 7221 DCFD 6BB2 E3E3 2C2C DEAD C0DE
* tag 'hw-misc-20240222' of https://github.com/philmd/qemu: (32 commits)
hw/sparc/leon3: Fix wrong usage of DO_UPCAST macro
hw/ide: Stop exposing internal.h to non-IDE files
hw/ide: Remove the include/hw/ide.h legacy file
hw/ide: Move IDE bus related definitions to a new header ide-bus.h
hw/ide: Move IDE device related definitions to ide-dev.h
hw/ide: Move IDE DMA related definitions to a separate header ide-dma.h
hw/ide: Split qdev.c into ide-bus.c and ide-dev.c
hw/ide: Add the possibility to disable the CompactFlash device in the build
hw/acpi/ich9_tco: Include missing 'migration/vmstate.h' header
hw/acpi/cpu: Use CPUState typedef
hw/acpi: Include missing 'qapi/qapi-types-acpi.h' generated header
hw/isa/meson.build: Sort alphabetically
hw/i386/pc_q35: Populate interrupt handlers before realizing LPC PCI function
hw/i386/pc_sysfw: Use qdev_is_realized() instead of QOM API
hw/i386/pc_sysfw: Inline pc_system_flash_create() and remove it
hw/i386/pc: Confine system flash handling to pc_sysfw
hw/i386/pc: Defer smbios_set_defaults() to machine_done
hw/i386/pc: Merge pc_guest_info_init() into pc_machine_initfn()
hw/i386/x86: Turn apic_xrupt_override into class attribute
hw/i386/pc: Do pc_cmos_init_late() from pc_machine_done()
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
# Conflicts:
# include/hw/i386/pc.h
include/hw/ide/internal.h is currently included by include/hw/ide/pci.h
and thus exposed to a lot of files that are not part of the IDE subsystem.
Stop including internal.h there and use the appropriate new headers
ide-bus.h and ide-dma.h instead.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-ID: <20240220085505.30255-8-thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
There was only one prototype left in this legacy file. Move it to
ide-dev.h to finally get rid of it.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-ID: <20240220085505.30255-7-thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Let's consolidate the public IDE bus related functions in a separate
header.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240220085505.30255-6-thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Untangle internal.h by moving public IDE device related
definitions to ide-dev.h.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240220085505.30255-5-thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
These definitions are required outside of the hw/ide/ code, too,
so lets's move them from internal.h to a new header called ide-dma.h.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240220085505.30255-4-thuth@redhat.com>
[PMD: Use IDEDMAOps typedef in struct IDEDMA]
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
For distros like downstream RHEL, it would be helpful to allow to disable
the CompactFlash device. For making this possible, we need a separate
Kconfig switch for this device, and the code should reside in a separate
file. Let's also introduce a new header ide-dev.h which can be used to
collect definitions related to IDE devices.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-ID: <20240220085505.30255-2-thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
We need the VMStateDescription structure definition from
"migration/vmstate.h" in order to declare vmstate_tco_io_sts.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Message-Id: <20240219141412.71418-4-philmd@linaro.org>
ACPIOSTInfo is a QAPI generated structure:
$ git grep -w ACPIOSTInfo
qapi/acpi.json:81:# @ACPIOSTInfo:
qapi/acpi.json:99:{ 'struct': 'ACPIOSTInfo',
qapi/acpi.json:109:# Return a list of ACPIOSTInfo for devices that support status
Include the "qapi/qapi-types-acpi.h" header to avoid the following
errors when including "hw/acpi/cpu.h" or "hw/acpi/memory_hotplug.h"
elsewhere:
include/hw/acpi/cpu.h:67:52: error: unknown type name 'ACPIOSTInfoList'
void acpi_cpu_ospm_status(CPUHotplugState *cpu_st, ACPIOSTInfoList ***list);
^
include/hw/acpi/memory_hotplug.h:51:55: error: unknown type name 'ACPIOSTInfoList'
void acpi_memory_ospm_status(MemHotplugState *mem_st, ACPIOSTInfoList ***list);
^
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Zhao Liu <zhao1.liu@intel.com>
Message-Id: <20240219141412.71418-2-philmd@linaro.org>
Rather than distributing PC system flash handling across three files, let's
confine it to one. Now, pc_system_firmware_init() creates, configures and cleans
up the system flash which makes the code easier to understand. It also avoids
the extra call to pc_system_flash_cleanup_unused() in the Xen case.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240208220349.4948-7-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Handling most of smbios data generation in the machine_done notifier is similar
to how the ARM virt machine handles it which also calls smbios_set_defaults()
there. The result is that all pc machines are freed from explicitly worrying
about smbios setup.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240208220349.4948-6-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Resolves redundant code in the piix and q35 machines.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240208220349.4948-5-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
The attribute isn't user-changeable and only true for pc-based machines. Turn it
into a class attribute which allows for inlining pc_guest_info_init() into
pc_machine_initfn().
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240208220349.4948-4-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Add the two IDE bus BusState pointers to the set we keep in PCMachineState.
This allows us to avoid passing them to pc_cmos_init(), and also will
allow a refactoring of how we call pc_cmos_init_late().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
[PMD: Do not zero-init pcms->idebus[] again]
Message-ID: <20240220160622.114437-2-peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
sysbus_add_io(...) is a simple wrapper to
memory_region_add_subregion(get_system_io(), ...).
It is used in 3 places; inline it directly.
Rationale: we want to move to an explicit I/O bus,
rather that an implicit one. Besides in heterogeneous
setup we can have more than one I/O bus.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20240216150441.45681-1-philmd@linaro.org>
[PMD: Include missing "exec/address-spaces.h" header]
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Since the named GPIO lines are a "public" interface to the device,
we can directly call qdev_connect_gpio_out_named(), making it
consistent with how the other A20 input source (port92) is wired.
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Yanan Wang <wangyanan55@huawei.com>
Message-Id: <20211218130437.1516929-6-f4bug@amsat.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Correct typos automatically found with the `typos` tool
<https://crates.io/crates/typos>
Signed-off-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Correct typos automatically found with the `typos` tool
<https://crates.io/crates/typos>
Signed-off-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Correct typos automatically found with the `typos` tool
<https://crates.io/crates/typos>
Signed-off-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Correct typos automatically found with the `typos` tool
<https://crates.io/crates/typos>
Signed-off-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
(mjt: fix comment style as suggested by Philippe)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Correct typos automatically found with the `typos` tool
<https://crates.io/crates/typos>
Signed-off-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Since pc_madt_cpu_entry() is only used by:
- hw/i386/acpi-build.c // single call
- hw/i386/acpi-common.c // definition
there is no need to expose it outside of hw/i386/.
Declare it in "acpi-common.h".
acpi-build.c doesn't need "hw/i386/pc.h" anymore.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Reviewed-by: Luc Michel <luc.michel@amd.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
HPET_INTCAP is specific to TYPE_HPET, so define it there.
hpet.c doesn't need to include "hw/i386/pc.h" anymore.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Reviewed-by: Luc Michel <luc.michel@amd.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Allow boards to use the device creation functions even if USB itself
is not available; of course the functions will fail inexorably, but
this can be okay if the calls are conditional on the existence of
some USB host controller device. This is for example the case for
hw/mips/loongson3_virt.c.
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
pc_machine_kvm_type() was introduced by commit e21be724ea ("i386/xen:
add pc_machine_kvm_type to initialize XEN_EMULATE mode") to do Xen
specific initialization by utilizing kvm_type method.
commit eeedfe6c63 ("hw/xen: Simplify emulated Xen platform init")
moves the Xen specific initialization to pc_basic_device_init().
There is no need to keep the PC specific kvm_type() implementation
anymore. So we'll fallback to kvm_arch_get_default_type(), which
simply returns 0.
Signed-off-by: Xiaoyao Li <xiaoyao.li@intel.com>
Reviewed-by: Isaku Yamahata <isaku.yamahata@intel.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Acked-by: David Woodhouse <dwmw@amazon.co.uk>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Message-ID: <20231007065819.27498-1-xiaoyao.li@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
No need to duplicate AHCIState::ports, directly access it.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20240213081201.78951-9-philmd@linaro.org>
AHCIState::ports should be unsigned. Besides, we never
check it for negative value. It is unlikely it was ever
used with more than INT32_MAX ports, so it is safe to
convert it to unsigned.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20240213081201.78951-7-philmd@linaro.org>
Since ahci_ide_create_devs() is not PCI specific, pass
it an AHCIState argument instead of PCIDevice.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20240213081201.78951-6-philmd@linaro.org>
Introduce the 'ich9' variable and inline ahci_get_num_ports().
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20240213081201.78951-5-philmd@linaro.org>
In order to be able to QOM-embed a structure, we need
its full definition. Move it from "ahci_internal.h"
to the new "hw/ide/ahci-pci.h" header.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20240213081201.78951-3-philmd@linaro.org>
Now there is an ncpus property, use it in order to deliver the IRQ to
multiple CPU.
Co-developed-by: Frederic Konrad <konrad.frederic@yahoo.fr>
Signed-off-by: Clément Chigot <chigot@adacore.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240131085047.18458-5-chigot@adacore.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Split out the headers for each peripherals and move them in their
right hardware directory.
Update Copyright and add SPDX-License-Identifier at the same time.
Co-developed-by: Frederic Konrad <konrad.frederic@yahoo.fr>
Signed-off-by: Clément Chigot <chigot@adacore.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240131085047.18458-2-chigot@adacore.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Instead of filling an array of all the possible IRQs, only call
qdev_get_gpio_in() when an IRQ is used. Remove the array from
RX62NState. Doing so we avoid calling qdev_get_gpio_in() on an
unrealized device.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20240213130341.1793-4-philmd@linaro.org>
"qemu/units.h" is not used in the "hw/rx/rx62n.h"
header, include it in the source where it is.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20240213130341.1793-3-philmd@linaro.org>
This field is not set. Remove it along with the dead
code it was guarding.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20240209090513.9401-7-philmd@linaro.org>
Since previous commit the MIPSITUState::cpu0 field is not
used anymore. Remove it.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20240209090513.9401-6-philmd@linaro.org>
Previous commit removed the MT*C0(SAAR) helpers which
were the only calls to itc_reconfigure() out of hw/,
we can reduce its scope and declare it statically.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20240209090513.9401-3-philmd@linaro.org>
