We are going to use spapr_build_fdt() for the boot time FDT and as an
update for SLOF during handling of H_CAS. SLOF will apply all properties
from the QEMU's FDT which is usually ok unless there are properties
changed by grub or guest kernel. The properties are:
bootargs, linux,initrd-start, linux,initrd-end, linux,stdout-path,
linux,rtas-base, linux,rtas-entry. Resetting those during CAS will most
likely cause grub failure.
Don't create such properties if we're booting without "-kernel" and
"-initrd" so they won't get included into the DT update blob and
therefore the guest is more likely to boot successfully.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
[dwg: Tweaked commit message based on Greg Kurz's input]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The device tree build by QEMU at the machine reset time is used by SLOF
to build its internal device tree but the node names are not preserved
exactly so when QEMU provides a device tree update in response to H_CAS,
it might become tricky to match a node from the update blob to
the actual node in SLOF.
This removed leading zeroes from "memory@" nodes and makes
the DTC checker happy.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Add a missing g_free(fdt) if the resulting tree is bigger
than the space allocated by SLOF.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
The number of NUMA nodes in the system is fixed from the command line.
Therefore, there's no need to recalculate it at reset time, and we can
determine the special gpu_numa_id value used for NVLink2 devices at init
time.
This simplifies the reset path a bit which will make further improvements
easier.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Tested-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Certain old guest versions don't understand the radix MMU introduced with
POWER ISA 3.0, but incorrectly select it if presented with the option at
CAS time. We workaround this in qemu by explicitly excluding the radix
(and other ISA 3.0 linked) options if the guest doesn't explicitly note
support for ISA 3.0.
This is handled by the 'cas_legacy_guest_workaround' flag, which is pretty
vague. Rename it to 'cas_pre_isa3_guest' to be clearer about what it's for.
In addition, we unnecessarily call spapr_populate_pa_features() with
different options when initially constructing the device tree and when
adjusting it at CAS time. At the initial construct time cas_pre_isa3_guest
is already false, so we can still use the flag, rather than explicitly
overriding it to be false at the callsite.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Unless the machine was started with kernel-irqchip=on, we cannot easily
tell if we're actually using an in-kernel or an emulated irqchip. This
information is important enough that it is worth printing it in 'info
pic'.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <156829860985.2073005.5893493824873412773.stgit@bahia.tls.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When we hotplug a CPU on memory-less/cpu-less node, the linux kernel
crashes.
This happens because linux kernel needs to know the NUMA topology at
start to be able to initialize the distance lookup table.
On pseries, the topology is provided by the firmware via the existing
CPUs and memory information. Thus a node without memory and CPU cannot be
discovered by the kernel.
To avoid the kernel crash, do not allow to start pseries with empty
nodes.
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Message-Id: <20190830161345.22436-1-lvivier@redhat.com>
[dwg: Rework to cope with movement of numa state from globals to MachineState]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Commit 78dd48df3 removed the last caller of register_savevm_live for an
instantiable device (rather than a single system wide device);
so trim out the parameter.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20190822115433.12070-1-dgilbert@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Bug fixes:
* Fix die-id validation regression (Eduardo Habkost)
* vmmouse: Properly reset state (Jan Kiszka)
* hostmem-file: fix pmem file size check (Stefan Hajnoczi)
* Keep query-hotpluggable-cpus output compatible with older QEMU
if '-smp dies' is not set (Igor Mammedov)
* migration: Do not re-read the clock on pre_save in case of paused guest
(Maxiwell S. Garcia)
Cleanups:
* NUMA code cleanups (Tao Xu)
* Remove stale externs from includes (Alex Bennée)
Features:
* qapi: report the default CPU type for each machine (Daniel P. Berrangé)
-----BEGIN PGP SIGNATURE-----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=u5HZ
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/ehabkost/tags/machine-next-pull-request' into staging
Machine + x86 queue, 2019-09-03
Bug fixes:
* Fix die-id validation regression (Eduardo Habkost)
* vmmouse: Properly reset state (Jan Kiszka)
* hostmem-file: fix pmem file size check (Stefan Hajnoczi)
* Keep query-hotpluggable-cpus output compatible with older QEMU
if '-smp dies' is not set (Igor Mammedov)
* migration: Do not re-read the clock on pre_save in case of paused guest
(Maxiwell S. Garcia)
Cleanups:
* NUMA code cleanups (Tao Xu)
* Remove stale externs from includes (Alex Bennée)
Features:
* qapi: report the default CPU type for each machine (Daniel P. Berrangé)
# gpg: Signature made Tue 03 Sep 2019 21:57:37 BST
# gpg: using RSA key 5A322FD5ABC4D3DBACCFD1AA2807936F984DC5A6
# gpg: issuer "ehabkost@redhat.com"
# gpg: Good signature from "Eduardo Habkost <ehabkost@redhat.com>" [full]
# Primary key fingerprint: 5A32 2FD5 ABC4 D3DB ACCF D1AA 2807 936F 984D C5A6
* remotes/ehabkost/tags/machine-next-pull-request:
migration: Do not re-read the clock on pre_save in case of paused guest
x86: do not advertise die-id in query-hotpluggbale-cpus if '-smp dies' is not set
i386/vmmouse: Properly reset state
hostmem-file: fix pmem file size check
qapi: report the default CPU type for each machine
pc: Don't make die-id mandatory unless necessary
pc: Improve error message when die-id is omitted
pc: Fix error message on die-id validation
numa: move numa global variable numa_info into MachineState
numa: move numa global variable have_numa_distance into MachineState
numa: move numa global variable nb_numa_nodes into MachineState
hw/arm: simplify arm_load_dtb
includes: remove stale [smp|max]_cpus externs
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Move existing numa global numa_info (renamed as "nodes") into NumaState.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Tao Xu <tao3.xu@intel.com>
Message-Id: <20190809065731.9097-5-tao3.xu@intel.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Add struct NumaState in MachineState and move existing numa global
nb_numa_nodes(renamed as "num_nodes") into NumaState. And add variable
numa_support into MachineClass to decide which submachines support NUMA.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Tao Xu <tao3.xu@intel.com>
Message-Id: <20190809065731.9097-3-tao3.xu@intel.com>
[ehabkost: include hw/boards.h again to fix build failures]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
A recent change in spapr_machine_reset() showed that resetting the compat
mode in spapr_machine_reset() for the boot vCPU and in spapr_cpu_reset()
for all other vCPUs was fragile. The fix was thus to reset the compat mode
for all vCPUs in spapr_machine_reset(), but we still have to propagate
it to hot-plugged CPUs. This is still performed from spapr_cpu_reset(),
hence resulting in ppc_set_compat() being called twice for every vCPU at
machine reset. Apart from wasting cycles, which isn't really an issue
during machine reset, this seems to indicate that spapr_cpu_reset() isn't
the best place to set the compat mode.
A natural candidate for CPU-hotplug specific code is spapr_core_plug().
Also, it sits in the same file as spapr_machine_reset() : this makes
it easier for someone who wants to know when the compat PVR is set.
Call ppc_set_compat() from there. This doesn't need to be done for
initial vCPUs since the compat PVR is 0 and spapr_machine_reset() sets
the appropriate value later. No need to do this on manually added vCPUS
on the destination QEMU during migration since the compat PVR is
part of the migrated vCPU state. Both conditions can be checked with
spapr_drc_hotplugged().
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <156701285312.499757.7807417667750711711.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The pseries guests do not normally allocate PCI resources and rely on
the system firmware doing so. Furthermore at least at some point in
the past the pseries guests won't even allowed to change BARs, probably
it is still the case for phyp. So since the initial commit we have [1]
which prevents resource reallocation.
This is not a problem until we want specific BAR alignments, for example,
PAGE_SIZE==64k to make sure we can still map MMIO BARs directly. For
the boot time devices we handle this in SLOF [2] but since QEMU's RTAS
does not allocate BARs, the guest does this instead and does not align
BARs even if Linux is given pci=resource_alignment=16@pci:0:0 as
PCI_PROBE_ONLY makes Linux ignore alignment requests.
ARM folks added a dial to control PCI_PROBE_ONLY via the device tree [3].
This makes use of the dial to advertise to the guest that we can handle
BAR reassignments. This limits the change to the latest pseries machine
to avoid old guests explosion.
We do not remove the flag from [1] as pseries guests are still supported
under phyp so having that removed may cause problems.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/arch/powerpc/platforms/pseries/setup.c?h=v5.1#n773
[2] https://git.qemu.org/?p=SLOF.git;a=blob;f=board-qemu/slof/pci-phb.fs;h=06729bcf77a0d4e900c527adcd9befe2a269f65d;hb=HEAD#l338
[3] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=f81c11af
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Message-Id: <20190719043734.108462-1-aik@ozlabs.ru>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
If we a migrate P8 machine to a P9 machine, the migration fails on
destination with:
error while loading state for instance 0x1 of device 'cpu'
load of migration failed: Operation not permitted
This is caused because the compat_pvr field is only present for the first
CPU.
Originally, spapr_machine_reset() calls ppc_set_compat() to set the value
max_compat_pvr for the first cpu and this was propagated to all CPUs by
spapr_cpu_reset(). Now, as spapr_cpu_reset() is called before that, the
value is not propagated to all CPUs and the migration fails.
To fix that, propagate the new value to all CPUs in spapr_machine_reset().
Fixes: 25c9780d38 ("spapr: Reset CAS & IRQ subsystem after devices")
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Message-Id: <20190826090812.19080-1-lvivier@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Suggested-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190709152053.16670-2-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[Rebased onto merge commit 95a9457fd44; missed instances of qom/cpu.h
in comments replaced]
PHBs already take care of clearing the MSIs from the bitmap during reset
or unplug. No need to do this globally from the machine code. Rather add
an assert to ensure that PHBs have acted as expected.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <156415228966.1064338.190189424190233355.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[dwg: Fix crash in qtest case where spapr->irq_map can be NULL at the
new assert()]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This has been useful to modify and test the Linux pseries suspend
code but it requires modification to the guest to call it (due to
being gated by other unimplemented features). It is not otherwise
used by Linux yet, but work is slowly progressing there.
This allows a (lightly modified) guest kernel to suspend with
`echo mem > /sys/power/state` and be resumed with system_wakeup
monitor command.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Message-Id: <20190722061752.22114-2-npiggin@gmail.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This implements the H_TPM_COMM hypercall, which is used by an
Ultravisor to pass TPM commands directly to the host's TPM device, or
a TPM Resource Manager associated with the device.
This also introduces a new virtual device, spapr-tpm-proxy, which
is used to configure the host TPM path to be used to service
requests sent by H_TPM_COMM hcalls, for example:
-device spapr-tpm-proxy,id=tpmp0,host-path=/dev/tpmrm0
By default, no spapr-tpm-proxy will be created, and hcalls will return
H_FUNCTION.
The full specification for this hypercall can be found in
docs/specs/ppc-spapr-uv-hcalls.txt
Since SVM-related hcalls like H_TPM_COMM use a reserved range of
0xEF00-0xEF80, we introduce a separate hcall table here to handle
them.
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com
Message-Id: <20190717205842.17827-3-mdroth@linux.vnet.ibm.com>
[dwg: Corrected #include for upstream change]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This has been useful to modify and test the Linux pseries suspend
code but it requires modification to the guest to call it (due to
being gated by other unimplemented features). It is not otherwise
used by Linux yet, but work is slowly progressing there.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Message-Id: <20190718034214.14948-5-npiggin@gmail.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
H_PROD is added, and H_CEDE is modified to test the prod bit
according to PAPR.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Message-Id: <20190718034214.14948-3-npiggin@gmail.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Implement cpu_exec_enter/exit on ppc which calls into new methods of
the same name in PPCVirtualHypervisorClass. These are used by spapr
to implement the splpar VPA dispatch counter initially.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Message-Id: <20190718034214.14948-2-npiggin@gmail.com>
[dwg: Removed unnecessary CONFIG_USER_ONLY checks as suggested by gkurz]
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
We've had the qemu and kernel KVM infrastructure to handle larger TCE
page sizes for a while, but forgot to update the defaults to actually
allow them. This turns that change on.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Add 4.2 machine types for arm/i440fx/q35/s390x/spapr.
For i440fx and q35, unversioned cpu models are still translated
to -v1, as 0788a56bd1 ("i386: Make unversioned CPU models be
aliases") states this should only transition to the latest cpu
model version in 4.3 (or later).
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20190724103524.20916-1-cohuck@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
sysemu/sysemu.h is a rather unfocused dumping ground for stuff related
to the system-emulator. Evidence:
* It's included widely: in my "build everything" tree, changing
sysemu/sysemu.h still triggers a recompile of some 1100 out of 6600
objects (not counting tests and objects that don't depend on
qemu/osdep.h, down from 5400 due to the previous two commits).
* It pulls in more than a dozen additional headers.
Split stuff related to run state management into its own header
sysemu/runstate.h.
Touching sysemu/sysemu.h now recompiles some 850 objects. qemu/uuid.h
also drops from 1100 to 850, and qapi/qapi-types-run-state.h from 4400
to 4200. Touching new sysemu/runstate.h recompiles some 500 objects.
Since I'm touching MAINTAINERS to add sysemu/runstate.h anyway, also
add qemu/main-loop.h.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190812052359.30071-30-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
[Unbreak OS-X build]
Commit e35704ba9c "numa: Move NUMA declarations from sysemu.h to
numa.h" left a few NUMA-related macros behind. Move them now.
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190812052359.30071-26-armbru@redhat.com>
In my "build everything" tree, changing hw/qdev-properties.h triggers
a recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
Many places including hw/qdev-properties.h (directly or via hw/qdev.h)
actually need only hw/qdev-core.h. Include hw/qdev-core.h there
instead.
hw/qdev.h is actually pointless: all it does is include hw/qdev-core.h
and hw/qdev-properties.h, which in turn includes hw/qdev-core.h.
Replace the remaining uses of hw/qdev.h by hw/qdev-properties.h.
While there, delete a few superfluous inclusions of hw/qdev-core.h.
Touching hw/qdev-properties.h now recompiles some 1200 objects.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Daniel P. Berrangé" <berrange@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190812052359.30071-22-armbru@redhat.com>
In my "build everything" tree, changing hw/hw.h triggers a recompile
of some 2600 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
The previous commits have left only the declaration of hw_error() in
hw/hw.h. This permits dropping most of its inclusions. Touching it
now recompiles less than 200 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-19-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing migration/qemu-file-types.h
triggers a recompile of some 2600 out of 6600 objects (not counting
tests and objects that don't depend on qemu/osdep.h).
The culprit is again hw/hw.h, which supposedly includes it for
convenience.
Include migration/qemu-file-types.h only where it's needed. Touching
it now recompiles less than 200 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190812052359.30071-10-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing sysemu/reset.h triggers a
recompile of some 2600 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
The main culprit is hw/hw.h, which supposedly includes it for
convenience.
Include sysemu/reset.h only where it's needed. Touching it now
recompiles less than 200 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-9-armbru@redhat.com>
This fixes a nasty regression in qemu-4.1 for the 'pseries' machine,
caused by the new "dual" interrupt controller model. Specifically,
qemu can crash when used with KVM if a 'system_reset' is requested
while there's active I/O in the guest.
The problem is that in spapr_machine_reset() we:
1. Reset the CAS vector state
spapr_ovec_cleanup(spapr->ov5_cas);
2. Reset all devices
qemu_devices_reset()
3. Reset the irq subsystem
spapr_irq_reset();
However (1) implicitly changes the interrupt delivery mode, because
whether we're using XICS or XIVE depends on the CAS state. We don't
properly initialize the new irq mode until (3) though - in particular
setting up the KVM devices.
During (2), we can temporarily drop the BQL allowing some irqs to be
delivered which will go to an irq system that's not properly set up.
Specifically, if the previous guest was in (KVM) XIVE mode, the CAS
reset will put us back in XICS mode. kvm_kernel_irqchip() still
returns true, because XIVE was using KVM, however XICs doesn't have
its KVM components intialized and kernel_xics_fd == -1. When the irq
is delivered it goes via ics_kvm_set_irq() which assert()s that
kernel_xics_fd != -1.
This change addresses the problem by delaying the CAS reset until
after the devices reset. The device reset should quiesce all the
devices so we won't get irqs delivered while we mess around with the
IRQ. The CAS reset and irq re-initialize should also now be under the
same BQL critical section so nothing else should be able to interrupt
it either.
We also move the spapr_irq_msi_reset() used in one of the legacy irq
modes, since it logically makes sense at the same point as the
spapr_irq_reset() (it's essentially an equivalent operation for older
machine types). Since we don't need to switch between different
interrupt controllers for those old machine types it shouldn't
actually be broken in those cases though.
Cc: Cédric Le Goater <clg@kaod.org>
Fixes: b2e22477 "spapr: add a 'reset' method to the sPAPR IRQ backend"
Fixes: 13db0cd9 "spapr: introduce a new sPAPR IRQ backend supporting
XIVE and XICS"
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Legacy '-numa node,mem' option has a number of issues and mgmt often
defaults to it. Unfortunately it's no possible to replace it with
an alternative '-numa memdev' without breaking migration compatibility.
What's possible though is to deprecate it, keeping option working with
old machine types only.
In order to help users to find out if being deprecated CLI option
'-numa node,mem' is still supported by particular machine type, add new
"numa-mem-supported" property to output of query-machines.
"numa-mem-supported" is set to 'true' for machines that currently support
NUMA, but it will be flipped to 'false' later on, once deprecation period
expires and kept 'true' only for old machine types that used to support
the legacy option so it won't break existing configuration that are using
it.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <1560172207-378962-1-git-send-email-imammedo@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The global smp variables in ppc are replaced with smp machine properties.
A local variable of the same name would be introduced in the declaration
phase if it's used widely in the context OR replace it on the spot if it's
only used once. No semantic changes.
Signed-off-by: Like Xu <like.xu@linux.intel.com>
Message-Id: <20190518205428.90532-5-like.xu@linux.intel.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
To get rid of the global smp_* variables we're currently using, it's recommended
to pass MachineState in the list of incoming parameters for functions that use
global smp variables, thus some redundant parameters are dropped. It's applied
for legacy smbios_*(), *_machine_reset(), hot_add_cpu() and mips *_create_cpu().
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Like Xu <like.xu@linux.intel.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190518205428.90532-3-like.xu@linux.intel.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Next pull request against qemu-4.1. The big thing here is adding
support for hot plug of P2P bridges, and PCI devices under P2P bridges
on the "pseries" machine (which doesn't use SHPC). Other than that
there's just a handful of fixes and small enhancements.
-----BEGIN PGP SIGNATURE-----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=ERgu
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-4.1-20190612' into staging
ppc patch queue 2019-06-12
Next pull request against qemu-4.1. The big thing here is adding
support for hot plug of P2P bridges, and PCI devices under P2P bridges
on the "pseries" machine (which doesn't use SHPC). Other than that
there's just a handful of fixes and small enhancements.
# gpg: Signature made Wed 12 Jun 2019 06:47:56 BST
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-4.1-20190612:
ppc/xive: Make XIVE generate the proper interrupt types
ppc/pnv: activate the "dumpdtb" option on the powernv machine
target/ppc: Use tcg_gen_gvec_bitsel
spapr: Allow hot plug/unplug of PCI bridges and devices under PCI bridges
spapr: Direct all PCI hotplug to host bridge, rather than P2P bridge
spapr: Don't use bus number for building DRC ids
spapr: Clean up DRC index construction
spapr: Clean up spapr_drc_populate_dt()
spapr: Clean up dt creation for PCI buses
spapr: Clean up device tree construction for PCI devices
spapr: Clean up device node name generation for PCI devices
target/ppc: Fix lxvw4x, lxvh8x and lxvb16x
spapr_pci: Improve error message
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
No header includes qemu-common.h after this commit, as prescribed by
qemu-common.h's file comment.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190523143508.25387-5-armbru@redhat.com>
[Rebased with conflicts resolved automatically, except for
include/hw/arm/xlnx-zynqmp.h hw/arm/nrf51_soc.c hw/arm/msf2-soc.c
block/qcow2-refcount.c block/qcow2-cluster.c block/qcow2-cache.c
target/arm/cpu.h target/lm32/cpu.h target/m68k/cpu.h target/mips/cpu.h
target/moxie/cpu.h target/nios2/cpu.h target/openrisc/cpu.h
target/riscv/cpu.h target/tilegx/cpu.h target/tricore/cpu.h
target/unicore32/cpu.h target/xtensa/cpu.h; bsd-user/main.c and
net/tap-bsd.c fixed up]
A P2P bridge will attempt to handle the hotplug with SHPC, which doesn't
work in the PAPR environment. Instead we want to direct all PCI hotplug
actions to the PAPR specific host bridge which will use the PAPR hotplug
mechanism.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
This makes some minor cleanups to spapr_drc_populate_dt(), renaming it to
the shorter and more idiomatic spapr_dt_drc() along the way.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Device nodes for PCI bridges (both host and P2P) describe both the bridge
device itself and the bus hanging off it, handling of this is a bit of a
mess.
spapr_dt_pci_device() has a few things it only adds for non-bridges, but
always adds #address-cells and #size-cells which should only appear for
bridges. But the walking down the subordinate PCI bus is done in one of
its callers spapr_populate_pci_devices_dt(). The PHB dt creation in
spapr_populate_pci_dt() open codes some similar logic to the bridge case.
This patch consolidates things in a bunch of ways:
* Bus specific dt info is now created in spapr_dt_pci_bus() used for both
P2P bridges and the host bridge. This includes walking subordinate
devices
* spapr_dt_pci_device() now calls spapr_dt_pci_bus() when called on a
P2P bridge
* We do detection of bridges with the is_bridge field of the device class,
rather than checking PCI config space directly, for consistency with
qemu's core PCI code.
* Several things are renamed for brevity and clarity
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Commit 0b8c89be7f7b added the hpt_maxpagesize capability to the migration
stream. This is okay for new machine types but it breaks backward migration
to older QEMUs, which don't expect the extra subsection.
Add a compatibility boolean flag to the sPAPR machine class and use it to
skip migration of the capability for machine types 4.0 and older. This
fixes migration to an older QEMU. Note that the destination will emit a
warning:
qemu-system-ppc64: warning: cap-hpt-max-page-size lower level (16) in incoming stream than on destination (24)
This is expected and harmless though. It is okay to migrate from a lower
HPT maximum page size (64k) to a greater one (16M).
Fixes: 0b8c89be7f7b "spapr: Add forgotten capability to migration stream"
Based-on: <20190522074016.10521-3-clg@kaod.org>
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155853262675.1158324.17301777846476373459.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Now that XIVE support is complete (QEMU emulated and KVM devices),
change the pseries machine to advertise both interrupt modes: XICS
(P7/P8) and XIVE (P9).
The machine default interrupt modes depends on the version. Current
settings are:
pseries default interrupt mode
4.1 dual
4.0 xics
3.1 xics
3.0 legacy xics (different IRQ number space layout)
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190522074016.10521-3-clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When we added support for NVLink2 passthrough devices, we changed the
phb_placement hook to handle the placement of NVLink2 bridges' specific
resources. For compatibility we use a version that doesn't do this
allocation for old machine types.
However, because of the delay between when the patch was posted and when
it was merged, we ended up with that compatibility hook applying for
machine versions 3.1 and earlier whereas it should apply for 4.0 and
earlier (since the patch was applied early in the 4.1 tree).
Fixes: ec132efaa8 "spapr: Support NVIDIA V100 GPU with NVLink2"
Reported-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
spapr machine capabilities are supposed to be sent in the migration stream
so that we can sanity check the source and destination have compatible
configuration. Unfortunately, when we added the hpt-max-page-size
capability, we forgot to add it to the migration state. This means that we
can generate spurious warnings when both ends are configured for large
pages, or potentially fail to warn if the source is configured for huge
pages, but the destination is not.
Fixes: 2309832afd "spapr: Maximum (HPT) pagesize property"
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
The ibm,purr and ibm,spurr device tree properties are used to indicate
that the processor implements the Processor Utilisation of Resources
Register (PURR) and Scaled Processor Utilisation of Resources Registers
(SPURR), respectively. Each property has a single value which represents
the level of architecture supported. A value of 1 for ibm,purr means
support for the version of the PURR defined in book 3 in version 2.02 of
the architecture. A value of 1 for ibm,spurr means support for the
version of the SPURR defined in version 2.05 of the architecture.
Add these properties for all processors for which the PURR and SPURR
registers are generated.
Fixes: 0da6f3fef9 "spapr: Reorganize CPU dt generation code"
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Message-Id: <20190506014803.21299-1-sjitindarsingh@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Here's the first ppc target pull request for qemu-4.1. This has a
number of things that have accumulated while qemu-4.0 was frozen.
* A number of emulated MMU improvements from Ben Herrenschmidt
* Assorted cleanups fro Greg Kurz
* A large set of mostly mechanical cleanups from me to make target/ppc
much closer to compliant with the modern coding style
* Support for passthrough of NVIDIA GPUs using NVLink2
As well as some other assorted fixes.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEdfRlhq5hpmzETofcbDjKyiDZs5IFAlzCnusACgkQbDjKyiDZ
s5LfhhAAuem5UBGKPKPj33c87HC+GGG+S4y89ic3ebyKplWulGgouHCa4Dnc7Y5m
9MfIEcljRDpuRJCEONo6yg9aaRb3cW2Go9TpTwxmF8o1suG/v5bIQIdiRbBuMa2t
yhNujVg5kkWSU1G4mCZjL9FS2ADPsxsKZVd73DPEqjlNJg981+2qtSnfR8SXhfnk
dSSKxyfC6Hq1+uhGkLI+xtft+BCTWOstjz+efHpZ5l2mbiaMeh7zMKrIXXy/FtKA
ufIyxbZznMS5MAZk7t90YldznfwOCqfh3di1kx8GTZ40LkBKbuI5LLHTG0sT75z5
LHwFuLkBgWmS8RyIRRh9opr7ifrayHx8bQFpW368Qu+PbPzUCcTVIrWUfPmaNR74
CkYJvhiYZfTwKtUeP7b2wUkHpZF4KINI4TKNaS4QAlm3DNbO67DFYkBrytpXsSzv
smEpe+sqlbY40olw9q4ESP80r+kGdEPLkRjfdj0R7qS4fsqAH1bjuSkNqlPaCTJQ
hNsoz2D+f56z0bBq4x8FRzDpqnBkdy4x6PlLxkJuAaV7WAtvq7n7tiMA3TRr/rIB
OYFP2xPNajjP8MfyOB94+S4WDltmsgXoM7HyyvrKp2JBpe7mFjpep5fMp5GUpweV
OOYrTsN1Nuu3kFpeimEc+IOyp1BWXnJF4vHhKTOqHeqZEs5Fgus=
=RpAK
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-4.1-20190426' into staging
ppc patch queue 2019-04-26
Here's the first ppc target pull request for qemu-4.1. This has a
number of things that have accumulated while qemu-4.0 was frozen.
* A number of emulated MMU improvements from Ben Herrenschmidt
* Assorted cleanups fro Greg Kurz
* A large set of mostly mechanical cleanups from me to make target/ppc
much closer to compliant with the modern coding style
* Support for passthrough of NVIDIA GPUs using NVLink2
As well as some other assorted fixes.
# gpg: Signature made Fri 26 Apr 2019 07:02:19 BST
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-4.1-20190426: (36 commits)
target/ppc: improve performance of large BAT invalidations
ppc/hash32: Rework R and C bit updates
ppc/hash64: Rework R and C bit updates
ppc/spapr: Use proper HPTE accessors for H_READ
target/ppc: Don't check UPRT in radix mode when in HV real mode
target/ppc/kvm: Convert DPRINTF to traces
target/ppc/trace-events: Fix trivial typo
spapr: Drop duplicate PCI swizzle code
spapr_pci: Get rid of duplicate code for node name creation
target/ppc: Style fixes for translate/spe-impl.inc.c
target/ppc: Style fixes for translate/vmx-impl.inc.c
target/ppc: Style fixes for translate/vsx-impl.inc.c
target/ppc: Style fixes for translate/fp-impl.inc.c
target/ppc: Style fixes for translate.c
target/ppc: Style fixes for translate_init.inc.c
target/ppc: Style fixes for monitor.c
target/ppc: Style fixes for mmu_helper.c
target/ppc: Style fixes for mmu-hash64.[ch]
target/ppc: Style fixes for mmu-hash32.[ch]
target/ppc: Style fixes for misc_helper.c
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
With MT-TCG, we are now running translation in a racy way, thus
we need to mimic hardware when it comes to updating the R and
C bits, by doing byte stores.
The current "store_hpte" abstraction is ill suited for this, we
replace it with two separate callbacks for setting R and C.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190411080004.8690-4-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
NVIDIA V100 GPUs have on-board RAM which is mapped into the host memory
space and accessible as normal RAM via an NVLink bus. The VFIO-PCI driver
implements special regions for such GPUs and emulates an NVLink bridge.
NVLink2-enabled POWER9 CPUs also provide address translation services
which includes an ATS shootdown (ATSD) register exported via the NVLink
bridge device.
This adds a quirk to VFIO to map the GPU memory and create an MR;
the new MR is stored in a PCI device as a QOM link. The sPAPR PCI uses
this to get the MR and map it to the system address space.
Another quirk does the same for ATSD.
This adds additional steps to sPAPR PHB setup:
1. Search for specific GPUs and NPUs, collect findings in
sPAPRPHBState::nvgpus, manage system address space mappings;
2. Add device-specific properties such as "ibm,npu", "ibm,gpu",
"memory-block", "link-speed" to advertise the NVLink2 function to
the guest;
3. Add "mmio-atsd" to vPHB to advertise the ATSD capability;
4. Add new memory blocks (with extra "linux,memory-usable" to prevent
the guest OS from accessing the new memory until it is onlined) and
npuphb# nodes representing an NPU unit for every vPHB as the GPU driver
uses it for link discovery.
This allocates space for GPU RAM and ATSD like we do for MMIOs by
adding 2 new parameters to the phb_placement() hook. Older machine types
set these to zero.
This puts new memory nodes in a separate NUMA node to as the GPU RAM
needs to be configured equally distant from any other node in the system.
Unlike the host setup which assigns numa ids from 255 downwards, this
adds new NUMA nodes after the user configures nodes or from 1 if none
were configured.
This adds requirement similar to EEH - one IOMMU group per vPHB.
The reason for this is that ATSD registers belong to a physical NPU
so they cannot invalidate translations on GPUs attached to another NPU.
It is guaranteed by the host platform as it does not mix NVLink bridges
or GPUs from different NPU in the same IOMMU group. If more than one
IOMMU group is detected on a vPHB, this disables ATSD support for that
vPHB and prints a warning.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
[aw: for vfio portions]
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Message-Id: <20190312082103.130561-1-aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
On non-P9 machines, the XIVE interrupt mode is not advertised, see
spapr_dt_ov5_platform_support(). Add a couple of checks on the machine
configuration to filter bogus setups and prevent OS failures :
Interrupt modes
CPU/Compat XICS XIVE dual
P8/P8 OK QEMU failure (1) OK (3)
P9/P8 OK QEMU failure (2) OK (3)
P9/P9 OK OK OK
(1) CPU exception model is incompatible with XIVE and the presenters
will fail to realize.
(2) CPU exception model is compatible with XIVE, but the XIVE CAS
advertisement is dropped when in POWER8 mode. So we could ended up
booting with the XIVE DT properties but without the HCALLs. Avoid
confusing Linux with such settings and fail under QEMU.
(3) force XICS in machine init
Remove the check on XIVE-only machines in spapr_machine_init(), which
has now become redundant.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190328100044.11408-1-clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
27461d69a0 "ppc: add host-serial and host-model machine attributes
(CVE-2019-8934)" introduced 'host-serial' and 'host-model' machine
properties for spapr to explicitly control the values advertised to the
guest in device tree properties with the same names.
The previous behaviour on KVM was to unconditionally populate the device
tree with the real host serial number and model, which leaks possibly
sensitive information about the host to the guest.
To maintain compatibility for old machine types, we allowed those props
to be set to "passthrough" to take the value from the host as before. Or
they could be set to "none" to explicitly omit the device tree items.
Special casing specific values on what's otherwise a user supplied string
is very ugly. So, this patch simplifies things by implementing the
backwards compatibility in a different way: we have a machine class flag
set for the older machines, and we only load the host values into the
device tree if A) they're not set by the user and B) we have that flag set.
This does mean that the "passthrough" functionality is no longer available
with the current machine type. That's ok though: if a user or management
layer really wants the information passed through they can read it
themselves (OpenStack Nova already does something similar for x86).
It also means the user can't explicitly ask for the values to be omitted
on the old machine types. I think that's an acceptable trade-off: if you
care enough about not leaking the host information you can either move to
the new machine type, or use a dummy value for the properties.
For the new machine type, this also removes an odd inconsistency
between running on a POWER and non-POWER (or non-Linux) hosts: if the
host information couldn't be read from where we expect (in the host's
device tree as exposed by Linux), we'd fallback to omitting the guest
device tree items.
While we're there, improve some poorly worded comments, and the help text
for the properties.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Tested-by: Greg Kurz <groug@kaod.org>
Alexey Kardashevskiy
David Gibson
Greg Kurz
Laurent Vivier
Dr. David Alan Gilbert
Peter Maydell
Tao Xu
Markus Armbruster
Nicholas Piggin
Michael Roth
Cornelia Huck
Igor Mammedov
Like Xu
Cédric Le Goater
Suraj Jitindar Singh
Benjamin Herrenschmidt