Make the MPU registers MPU_MAIR0 and MPU_MAIR1 banked if v8M security
extensions are enabled.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-13-git-send-email-peter.maydell@linaro.org
Make the VTOR register banked if v8M security extensions are enabled.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-12-git-send-email-peter.maydell@linaro.org
Make the CONTROL register banked if v8M security extensions are enabled.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-10-git-send-email-peter.maydell@linaro.org
Make the FAULTMASK register banked if v8M security extensions are enabled.
Note that we do not yet implement the functionality of the new
AIRCR.PRIS bit (which allows the effect of the NS copy of FAULTMASK to
be restricted).
This patch includes the code to determine for v8M which copy
of FAULTMASK should be updated on exception exit; further
changes will be required to the exception exit code in general
to support v8M, so this is just a small piece of that.
The v8M ARM ARM introduces a notation where individual paragraphs
are labelled with R (for rule) or I (for information) followed
by a random group of subscript letters. In comments where we want
to refer to a particular part of the manual we use this convention,
which should be more stable across document revisions than using
section or page numbers.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-9-git-send-email-peter.maydell@linaro.org
Make the PRIMASK register banked if v8M security extensions are enabled.
Note that we do not yet implement the functionality of the new
AIRCR.PRIS bit (which allows the effect of the NS copy of PRIMASK to
be restricted).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-8-git-send-email-peter.maydell@linaro.org
Make the BASEPRI register banked if v8M security extensions are enabled.
Note that we do not yet implement the functionality of the new
AIRCR.PRIS bit (which allows the effect of the NS copy of BASEPRI to
be restricted).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-7-git-send-email-peter.maydell@linaro.org
Now that MPU lookups can return different results for v8M
when the CPU is in secure vs non-secure state, we need to
have separate MMU indexes; add the secure counterparts
to the existing three M profile MMU indexes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-6-git-send-email-peter.maydell@linaro.org
If a v8M CPU supports the security extension then we need to
give it two AddressSpaces, the same way we do already for
an A profile core with EL3.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-5-git-send-email-peter.maydell@linaro.org
As the first step in implementing ARM v8M's security extension:
* add a new feature bit ARM_FEATURE_M_SECURITY
* add the CPU state field that indicates whether the CPU is
currently in the secure state
* add a migration subsection for this new state
(we will add the Secure copies of banked register state
to this subsection in later patches)
* add a #define for the one new-in-v8M exception type
* make the CPU debug log print S/NS status
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-4-git-send-email-peter.maydell@linaro.org
Implement the behavioural side of the new PMSAv8 specification.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-3-git-send-email-peter.maydell@linaro.org
As part of ARMv8M, we need to add support for the PMSAv8 MPU
architecture.
PMSAv8 differs from PMSAv7 both in register/data layout (for instance
using base and limit registers rather than base and size) and also in
behaviour (for example it does not have subregions); rather than
trying to wedge it into the existing PMSAv7 code and data structures,
we define separate ones.
This commit adds the data structures which hold the state for a
PMSAv8 MPU and the register interface to it. The implementation of
the MPU behaviour will be added in a subsequent commit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1503414539-28762-2-git-send-email-peter.maydell@linaro.org
ARM is a fixed-length ISA and we can compute the page crossing
condition exactly once during init_disas_context.
Reviewed-by: Emilio G. Cota <cota@braap.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
We need not check for ARM vs Thumb state in order to dispatch
disassembly of every instruction.
Tested-by: Emilio G. Cota <cota@braap.org>
Reviewed-by: Emilio G. Cota <cota@braap.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
We can check for single-step just once.
Reviewed-by: Emilio G. Cota <cota@braap.org>
Reviewed-by: Lluís Vilanova <vilanova@ac.upc.edu>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Since AArch64 uses a fixed-width ISA, we can pre-compute the number of
insns remaining on the page. Also, we can check for single-step once.
Reviewed-by: Emilio G. Cota <cota@braap.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Incrementally paves the way towards using the generic instruction translation
loop.
Reviewed-by: Emilio G. Cota <cota@braap.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Lluís Vilanova <vilanova@ac.upc.edu>
Message-Id: <150002606914.22386.15524101311003685068.stgit@frigg.lan>
[rth: Move tb->size computation and use that result.]
Signed-off-by: Richard Henderson <rth@twiddle.net>
Incrementally paves the way towards using the generic instruction translation
loop.
Signed-off-by: Lluís Vilanova <vilanova@ac.upc.edu>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Alex Benneé <alex.benee@linaro.org>
Message-Id: <150002582711.22386.191527630537864599.stgit@frigg.lan>
[rth: Move tb->size computation and use that result.]
Signed-off-by: Richard Henderson <rth@twiddle.net>
Incrementally paves the way towards using the generic instruction translation
loop.
Reviewed-by: Emilio G. Cota <cota@braap.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Lluís Vilanova <vilanova@ac.upc.edu>
Message-Id: <150002558503.22386.1149037590886263349.stgit@frigg.lan>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Incrementally paves the way towards using the generic instruction translation
loop.
Reviewed-by: Emilio G. Cota <cota@braap.org>
Signed-off-by: Lluís Vilanova <vilanova@ac.upc.edu>
Message-Id: <150002534291.22386.13499916738708680298.stgit@frigg.lan>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Incrementally paves the way towards using the generic instruction translation
loop.
Reviewed-by: Emilio G. Cota <cota@braap.org>
Signed-off-by: Lluís Vilanova <vilanova@ac.upc.edu>
Message-Id: <150002510079.22386.10164419868911710218.stgit@frigg.lan>
[rth: Adjust for translate_insn interface change.]
Signed-off-by: Richard Henderson <rth@twiddle.net>
Incrementally paves the way towards using the generic instruction translation
loop.
Reviewed-by: Emilio G. Cota <cota@braap.org>
Signed-off-by: Lluís Vilanova <vilanova@ac.upc.edu>
Message-Id: <150002485863.22386.13949856269576226529.stgit@frigg.lan>
[rth: Adjust for translate_insn interface change.]
Signed-off-by: Richard Henderson <rth@twiddle.net>
Incrementally paves the way towards using the generic instruction translation
loop.
Reviewed-by: Emilio G. Cota <cota@braap.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Lluís Vilanova <vilanova@ac.upc.edu>
Message-Id: <150002461630.22386.14827196109258040543.stgit@frigg.lan>
[rth: Use DISAS_TOO_MANY for "execute only one more" after bp.]
Signed-off-by: Richard Henderson <rth@twiddle.net>
Incrementally paves the way towards using the generic instruction translation
loop.
Signed-off-by: Lluís Vilanova <vilanova@ac.upc.edu>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Alex Benneé <alex.benee@linaro.org>
Message-Id: <150002413187.22386.156315485813606121.stgit@frigg.lan>
[rth: Use DISAS_TOO_MANY for "execute only one more" after bp.]
Signed-off-by: Richard Henderson <rth@twiddle.net>
Incrementally paves the way towards using the generic instruction translation
loop.
Signed-off-by: Lluís Vilanova <vilanova@ac.upc.edu>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Alex Benneé <alex.benee@linaro.org>
Message-Id: <150002388959.22386.12439646324427589940.stgit@frigg.lan>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Incrementally paves the way towards using the generic instruction translation
loop.
Signed-off-by: Lluís Vilanova <vilanova@ac.upc.edu>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Alex Benneé <alex.benee@linaro.org>
Message-Id: <150002364681.22386.1701754996184325808.stgit@frigg.lan>
[rth: Adjust for tb_start interface change.]
Signed-off-by: Richard Henderson <rth@twiddle.net>
Incrementally paves the way towards using the generic instruction translation
loop.
Signed-off-by: Lluís Vilanova <vilanova@ac.upc.edu>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Alex Benneé <alex.benee@linaro.org>
Message-Id: <150002340430.22386.10889954302345646107.stgit@frigg.lan>
[rth: Adjust for max_insns interface change.]
Signed-off-by: Richard Henderson <rth@twiddle.net>
Incrementally paves the way towards using the generic instruction translation
loop.
Signed-off-by: Lluís Vilanova <vilanova@ac.upc.edu>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Alex Benneé <alex.benee@linaro.org>
Message-Id: <150002316201.22386.12115078843605656029.stgit@frigg.lan>
[rth: Adjust for max_insns interface change.]
Signed-off-by: Richard Henderson <rth@twiddle.net>
Incrementally paves the way towards using the generic
instruction translation loop.
Signed-off-by: Lluís Vilanova <vilanova@ac.upc.edu>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Alex Benneé <alex.benee@linaro.org>
Message-Id: <150002291931.22386.11441154993010495674.stgit@frigg.lan>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Incrementally paves the way towards using the generic instruction translation
loop.
Signed-off-by: Lluís Vilanova <vilanova@ac.upc.edu>
Reviewed-by: Emilio G. Cota <cota@braap.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Message-Id: <150002243497.22386.8888053391875656102.stgit@frigg.lan>
[rth: Move tb->size computation and use that result.]
Signed-off-by: Richard Henderson <rth@twiddle.net>
Incrementally paves the way towards using the generic instruction translation
loop.
Signed-off-by: Lluís Vilanova <vilanova@ac.upc.edu>
Reviewed-by: Emilio G. Cota <cota@braap.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Message-Id: <150002219289.22386.17959138704858928730.stgit@frigg.lan>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Incrementally paves the way towards using the generic instruction translation
loop.
Signed-off-by: Lluís Vilanova <vilanova@ac.upc.edu>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Emilio G. Cota <cota@braap.org>
Message-Id: <150002195074.22386.16195894320027075398.stgit@frigg.lan>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Incrementally paves the way towards using the generic instruction translation
loop.
Signed-off-by: Lluís Vilanova <vilanova@ac.upc.edu>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Emilio G. Cota <cota@braap.org>
Message-Id: <150002170871.22386.2172835658104140576.stgit@frigg.lan>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Incrementally paves the way towards using the generic instruction translation
loop.
Signed-off-by: Lluís Vilanova <vilanova@ac.upc.edu>
Reviewed-by: Emilio G. Cota <cota@braap.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Alex Benneé <alex.benee@linaro.org>
Message-Id: <150002146647.22386.13380064201042141261.stgit@frigg.lan>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Incrementally paves the way towards using the generic instruction translation
loop.
Reviewed-by: Emilio G. Cota <cota@braap.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Alex Benneé <alex.benee@linaro.org>
Signed-off-by: Lluís Vilanova <vilanova@ac.upc.edu>
Message-Id: <150002122448.22386.16854673576827449259.stgit@frigg.lan>
[rth: Adjust for max_insns interface change.]
Signed-off-by: Richard Henderson <rth@twiddle.net>
Incrementally paves the way towards using the generic instruction translation
loop.
Signed-off-by: Lluís Vilanova <vilanova@ac.upc.edu>
Reviewed-by: Emilio G. Cota <cota@braap.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Alex Benneé <alex.benee@linaro.org>
Message-Id: <150002098212.22386.17313318023406046314.stgit@frigg.lan>
Signed-off-by: Richard Henderson <rth@twiddle.net>
There's nothing magic about the exception that we generate in order
to execute the magic kernel page. We can and should allow gdb to
set a breakpoint at this location.
Reviewed-by: Emilio G. Cota <cota@braap.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Used later. An enum makes expected values explicit and
bounds the value space of switches.
Signed-off-by: Lluís Vilanova <vilanova@ac.upc.edu>
Reviewed-by: Emilio G. Cota <cota@braap.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Message-Id: <150002049746.22386.2316077281615710615.stgit@frigg.lan>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Fold DISAS_EXC and DISAS_TB_JUMP into DISAS_NORETURN.
In both cases all following code is dead. In the first
case because we have exited the TB via exception; in the
second case because we have exited the TB via goto_tb
and its associated machinery.
Reviewed-by: Emilio G. Cota <cota@braap.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
This target is not sophisticated in its use of cleanups at the
end of the translation loop. For the most part, any condition
that exits the TB is dealt with by emitting the exiting opcode
right then and there. Therefore the only is_jmp indicator that
is needed is DISAS_NORETURN.
For two stack segment modifying cases, we have not yet exited
the TB (therefore DISAS_NORETURN feels wrong), but intend to exit.
The caller of gen_movl_seg_T0 currently checks for any non-zero
value, therefore DISAS_TOO_MANY seems acceptable for that usage.
Reviewed-by: Emilio G. Cota <cota@braap.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
For "ldp x0, x1, [x0]", if the second load is on a second page and
the second page is unmapped, the exception would be raised with x0
already modified. This means the instruction couldn't be restarted.
Cc: qemu-arm@nongnu.org
Cc: qemu-stable@nongnu.org
Reported-by: Andrew <andrew@fubar.geek.nz>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20170825224833.4463-1-richard.henderson@linaro.org
Fixes: https://bugs.launchpad.net/qemu/+bug/1713066
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
[PMM: tweaked comment format]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
For external aborts, we will want to be able to specify the EA
(external abort type) bit in the syndrome field. Allow callers of
deliver_fault() to do that by adding a field to ARMMMUFaultInfo which
we use when constructing the syndrome values.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
We currently have some similar code in tlb_fill() and in
arm_cpu_do_unaligned_access() for delivering a data abort or prefetch
abort. We're also going to want to do the same thing to handle
external aborts. Factor out the common code into a new function
deliver_fault().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
If a KVM PMU init or set-irq attr call fails we just silently stop
the PMU DT node generation. The only way they could fail, though,
is if the attr's respective KVM has-attr call fails. But that should
never happen if KVM advertises the PMU capability, because both
attrs have been available since the capability was introduced. Let's
just abort if this should-never-happen stuff does happen, because,
if it does, then something is obviously horribly wrong.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Message-id: 1500471597-2517-5-git-send-email-drjones@redhat.com
[PMM: change kvm32.c kvm_arm_pmu_init() to the new API too]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Move the in-kernel-irqchip test to only guard the set-irq
stage, not the init stage of the PMU. Also add the PMU to
the KVM device irq line synchronization to enable its use.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Message-id: 1500471597-2517-4-git-send-email-drjones@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When adding a PMU with a userspace irqchip we skip the set-irq
stage of device creation. Split the 'create' function into two
functions 'init' and 'set-irq' so they may be called separately.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Christoffer Dall <cdall@linaro.org>
Message-id: 1500471597-2517-3-git-send-email-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Mimicking gicv3-maintenance-interrupt, add the PMU's interrupt to
CPU state.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1500471597-2517-2-git-send-email-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a utility function for testing whether the CPU is in Handler
mode; this is just a check whether v7m.exception is non-zero, but
we do it in several places and it makes the code a bit easier
to read to not have to mentally figure out what the test is testing.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1501692241-23310-14-git-send-email-peter.maydell@linaro.org
Move the code in arm_v7m_cpu_do_interrupt() that calculates the
magic LR value down to when we're actually going to use it.
Having the calculation and use so far apart makes the code
a little harder to understand than it needs to be.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1501692241-23310-13-git-send-email-peter.maydell@linaro.org
Make the arm_cpu_dump_state() debug logging handle the M-profile XPSR
rather than assuming it's an A-profile CPSR. On M profile the PSR
line of a register dump will now look like this:
XPSR=41000000 -Z-- T priv-thread
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1501692241-23310-12-git-send-email-peter.maydell@linaro.org
For M profile the XPSR is a similar but not identical format to the
A profile CPSR/SPSR. (For instance the Thumb bit is in a different
place.) For guest accesses we make the M profile code go through
xpsr_read() and xpsr_write() which handle the different layout.
However for migration we use cpsr_read() and cpsr_write() to
marshal state into and out of the migration data stream. This
is pretty confusing and works more by luck than anything else.
Make M profile migration use xpsr_read() and xpsr_write() instead.
The most complicated part of this is handling the possibility
that the migration source is an older QEMU which hands us a
CPSR format value; helpfully we can always tell the two apart.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1501692241-23310-11-git-send-email-peter.maydell@linaro.org
We currently store the M profile CPU register state PRIMASK and
FAULTMASK in the daif field of the CPU state in its I and F
bits. This is a legacy from the original implementation, which
tried to share the cpu_exec_interrupt code between A profile
and M profile. We've since separated out the two cases because
they are significantly different, so now there is no common
code between M and A profile which looks at env->daif: all the
uses are either in A-only or M-only code paths. Sharing the state
fields now is just confusing, and will make things awkward
when we implement v8M, where the PRIMASK and FAULTMASK
registers are banked between security states.
Switch M profile over to using v7m.faultmask and v7m.primask
fields for these registers.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1501692241-23310-10-git-send-email-peter.maydell@linaro.org
The M profile XPSR is almost the same format as the A profile CPSR,
but not quite. Define some XPSR_* macros and use them where we
definitely dealing with an XPSR rather than reusing the CPSR ones.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1501692241-23310-9-git-send-email-peter.maydell@linaro.org
When we switched our handling of exception exit to detect
the magic addresses at translate time rather than via
a do_unassigned_access hook, we forgot to update a
comment; correct the omission.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1501692241-23310-8-git-send-email-peter.maydell@linaro.org
Remove the comment that claims that some MPU_CTRL bits are stored
in sctlr_el[1]. This has never been true since MPU_CTRL was added
in commit 29c483a506 -- the comment is a leftover from
Michael Davidsaver's original implementation, which I modified
not to use sctlr_el[1]; I forgot to delete the comment then.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1501692241-23310-7-git-send-email-peter.maydell@linaro.org
Tighten up the T32 decoder in the places where new v8M instructions
will be:
* TT/TTT/TTA/TTAT are in what was nominally LDREX/STREX r15, ...
which is UNPREDICTABLE:
make the UNPREDICTABLE behaviour be to UNDEF
* BXNS/BLXNS are distinguished from BX/BLX via the low 3 bits,
which in previous architectural versions are SBZ:
enforce the SBZ via UNDEF rather than ignoring it, and move
the "ARCH(5)" UNDEF case up so we don't leak a TCG temporary
* SG is in the encoding which would be LDRD/STRD with rn = r15;
this is UNPREDICTABLE and we currently UNDEF:
move this check further up the code so that we don't leak
TCG temporaries in the UNDEF case and have a better place
to put the SG decode.
This means that if a v8M binary is accidentally run on v7M
or if a test case hits something that we haven't implemented
yet the behaviour will be obvious (UNDEF) rather than obscure
(plough on treating it as a different instruction).
In the process, add some comments about the instruction patterns
at these points in the decode. Our Thumb and ARM decoders are
very difficult to understand currently, but gradually adding
comments like this should help to clarify what exactly has
been decoded when.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1501692241-23310-5-git-send-email-peter.maydell@linaro.org
Currently get_phys_addr() has PMSAv7 handling before the
"is translation disabled?" check, and then PMSAv5 after it.
Tidy this up by making the PMSAv5 code handle the "MPU disabled"
case itself, so that we have all the PMSA code in one place.
This will make adding the PMSAv8 code slightly cleaner, and
also means that pre-v7 PMSA cores benefit from the MPU lookup
logging that the PMSAv7 codepath had.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1501692241-23310-4-git-send-email-peter.maydell@linaro.org
M profile cores can never trap on WFI or WFE instructions. Check for
M profile in check_wfx_trap() to ensure this.
The existing code will do the right thing for v7M cores because
the hcr_el2 and scr_el3 registers will be all-zeroes and so we
won't attempt to trap, but when we start setting ARM_FEATURE_V8
for v8M cores the v8A handling of SCTLR.nTWE and .nTWI will not
give the right results.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1501692241-23310-3-git-send-email-peter.maydell@linaro.org
In the ARM get_phys_addr() code, switch to using the MMUAccessType
enum and its MMU_* values rather than int and literal 0/1/2.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1501692241-23310-2-git-send-email-peter.maydell@linaro.org
-----BEGIN PGP SIGNATURE-----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=eUZW
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/armbru/tags/pull-qapi-2017-09-01-v3' into staging
QAPI patches for 2017-09-01
# gpg: Signature made Mon 04 Sep 2017 12:30:31 BST
# gpg: using RSA key 0x3870B400EB918653
# gpg: Good signature from "Markus Armbruster <armbru@redhat.com>"
# gpg: aka "Markus Armbruster <armbru@pond.sub.org>"
# Primary key fingerprint: 354B C8B3 D7EB 2A6B 6867 4E5F 3870 B400 EB91 8653
* remotes/armbru/tags/pull-qapi-2017-09-01-v3: (47 commits)
qapi: drop the sentinel in enum array
qapi: Change data type of the FOO_lookup generated for enum FOO
qapi: Convert indirect uses of FOO_lookup[...] to qapi_enum_lookup()
qapi: Mechanically convert FOO_lookup[...] to FOO_str(...)
qapi: Generate FOO_str() macro for QAPI enum FOO
qapi: Avoid unnecessary use of enum lookup table's sentinel
qapi: Use qapi_enum_parse() in input_type_enum()
crypto: Use qapi_enum_parse() in qcrypto_block_luks_name_lookup()
quorum: Use qapi_enum_parse() in quorum_open()
block: Use qemu_enum_parse() in blkdebug_debug_breakpoint()
hmp: Use qapi_enum_parse() in hmp_migrate_set_parameter()
hmp: Use qapi_enum_parse() in hmp_migrate_set_capability()
tpm: Clean up model registration & lookup
tpm: Clean up driver registration & lookup
qapi: Drop superfluous qapi_enum_parse() parameter max
qapi: Update qapi-code-gen.txt examples to match current code
qapi-schema: Improve section headings
qapi-schema: Move queries from common.json to qapi-schema.json
qapi-schema: Make block-core.json self-contained
qapi-schema: Fold event.json back into qapi-schema.json
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
it's just a wrapper, drop it and use cpu_generic_init() directly
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <1503592308-93913-26-git-send-email-imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
it's just a wrapper, drop it and use cpu_generic_init() directly
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <1503592308-93913-25-git-send-email-imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
it's just a wrapper, drop it and use cpu_generic_init() directly
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Stafford Horne <shorne@gmail.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <1503592308-93913-24-git-send-email-imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
it's just a wrapper, drop it and use cpu_generic_init() directly
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <1503592308-93913-23-git-send-email-imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
it's just a wrapper, drop it and use cpu_generic_init() directly
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Michael Walle <michael@walle.cc>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <1503592308-93913-22-git-send-email-imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
it's just a wrapper, drop it and use cpu_generic_init() directly
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <1503592308-93913-21-git-send-email-imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
it's just a wrapper, drop it and use cpu_generic_init() directly
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <1503592308-93913-20-git-send-email-imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
it's just a wrapper, drop it and use cpu_generic_init() directly
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1503592308-93913-19-git-send-email-imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
it's just a wrapper, drop it and use cpu_generic_init() directly
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <1503592308-93913-18-git-send-email-imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
it's just a wrapper, drop it and use cpu_generic_init() directly
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <1503592308-93913-17-git-send-email-imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
call xtensa_irq_init() at realize time which makes
cpu_xtensa_init() like generic cpu creation function.
As result we can replace it with cpu_generic_init()
which does the same job, reducing code duplication a bit.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1503592308-93913-16-git-send-email-imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
cpu_tilegx_init() always falls back to TYPE_TILEGX_CPU object
regardless of cpu_model. Put fallback logic into
tilegx_cpu_class_by_name() which would translate any cpu_model
into TYPE_TILEGX_CPU class and replace cpu_tilegx_init()
with cpu_generic_init().
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <1503592308-93913-15-git-send-email-imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
cpu_nios2_init() always falls back to TYPE_NIOS2_CPU object
regardless of cpu_model. Put fallback logic into
nios2_cpu_class_by_name() which would translate any cpu_model
into TYPE_NIOS2_CPU class and replace cpu_nios2_init()
with cpu_generic_init()
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1503592308-93913-14-git-send-email-imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
cpu_mb_init() always falls back to TYPE_MICROBLAZE_CPU object
regardless of cpu_model. Put fallback logic into
mb_cpu_class_by_name() which would translate any cpu_model
into TYPE_MICROBLAZE_CPU class and replace cpu_mb_init()
with cpu_generic_init().
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1503592308-93913-13-git-send-email-imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
call register_m68k_insns() at realize time which makes
cpu_m68k_init() typical object creation function.
As result we can replace it with cpu_generic_init()
which does the same job, reducing code duplication a bit.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Tested-by: Thomas Huth <huth@tuxfamily.org>
Acked-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <1503592308-93913-12-git-send-email-imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
drop custom cpu_hppa_init() in favor of cpu_generic_init(),
to make cpu_generic_init() work all we need is to provide
cc->class_by_name callback that would resolve any cpu_model
to the sole TYPE_HPPA_CPU to match current behaviour.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Richard Henderson <rth@twiddle.net>
Message-Id: <1503592308-93913-11-git-send-email-imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
cpu_alpha_init() used to provide default fallback if invalid
(i.e. non existent) cpu_model were provided.
dp264 machine provides its own default so sole user of fallback
is [bsd|linux]-user targets which specifies 'any' cpu model that
fallbacks to "ev67" in cpu_alpha_init(). Push fallback handling
into alpha_cpu_class_by_name() and replace cpu_alpha_init() with
cpu_generic_init().
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Richard Henderson <rth@twiddle.net>
Message-Id: <1503592308-93913-10-git-send-email-imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
cpu_s390x_init() is used only *-user targets indirectly
via cpu_init() macro and has a hack to assign ids to created
cpus (I'm not sure if 'id' really matters to *-user emulation).
So to on safe side, instead of having custom wrapper to do numbering
replace it with cpu_generic_init() and use S390CPUClass::next_cpu_id
which could serve the same purpose as static variable and move cpu->id
initialization to s390_cpu_initfn for CONFIG_USER_ONLY use-case.
PS:
ifdef is ugly but it allows us to hide s390x detail that isn't
set by *-user targets and reuse generic cpu creation utility
for btoh machine and user emulation.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <1504185578-80843-1-git-send-email-imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
it's just a wrapper, drop it and use cpu_generic_init() directly
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1503592308-93913-8-git-send-email-imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
with features converted to properties we can use the same
approach as x86 for features parsing and drop legacy
approach that manipulated CPU instance directly.
New sparc_cpu_parse_features() will allow only +-feat
and explicitly disable feat=on|off syntax for now.
With that in place and sparc_cpu_parse_features() providing
generic CPUClass::parse_features callback, the cpu_sparc_init()
will do the same job as cpu_generic_init() so replace content
of cpu_sparc_init() with it.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1503672460-109436-1-git-send-email-imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
SPARCCPU::env was initialized from previously set properties
(with help of sparc_cpu_parse_features) in cpu_sparc_register().
However there is not reason to keep it there as this task is
typically done at realize time. So move post properties
initialization into sparc_cpu_realizefn, which brings
cpu_sparc_init() closer to cpu_generic_init().
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1503592308-93913-6-git-send-email-imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
SPARC is the last target that uses legacy way of parsing
and initializing cpu features, drop legacy approach and
convert features to properties so that SPARC could as minimum
benefit from generic cpu_generic_init(), common with
x86 +-feat parser
PS:
the main purpose is to remove legacy way of cpu creation as
a blocker for unifying cpu creation code across targets.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1503592308-93913-5-git-send-email-imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Make CPUSPARCState::def embedded so it would be allocated as part
of cpu instance and we won't have to worry about cleaning def pointer
up mannualy on cpu destruction.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1503592308-93913-4-git-send-email-imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
QOMfy cpu models handling introducing propper cpu types
for each cpu model.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1503592308-93913-3-git-send-email-imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Add a new base CPU model called 'EPYC' to model processors from AMD EPYC
family (which includes EPYC 76xx,75xx,74xx, 73xx and 72xx).
The following features bits have been added/removed compare to Opteron_G5
Added: monitor, movbe, rdrand, mmxext, ffxsr, rdtscp, cr8legacy, osvw,
fsgsbase, bmi1, avx2, smep, bmi2, rdseed, adx, smap, clfshopt, sha
xsaveopt, xsavec, xgetbv1, arat
Removed: xop, fma4, tbm
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Tom Lendacky <Thomas.Lendacky@amd.com>
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Message-Id: <20170815170051.127257-1-brijesh.singh@amd.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Add [apic-id] support for hmp command "info lapic", which is
useful when debugging ipi and so on. Current behavior is not
changed when the parameter isn't specified.
Signed-off-by: Yi Wang <wang.yi59@zte.com.cn>
Signed-off-by: Yun Liu <liu.yunh@zte.com.cn>
Message-Id: <1501049917-4701-3-git-send-email-wang.yi59@zte.com.cn>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>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=jCiK
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/elmarco/tags/tidy-pull-request' into staging
# gpg: Signature made Thu 31 Aug 2017 11:29:33 BST
# gpg: using RSA key 0xDAE8E10975969CE5
# gpg: Good signature from "Marc-André Lureau <marcandre.lureau@redhat.com>"
# gpg: aka "Marc-André Lureau <marcandre.lureau@gmail.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 87A9 BD93 3F87 C606 D276 F62D DAE8 E109 7596 9CE5
* remotes/elmarco/tags/tidy-pull-request: (29 commits)
eepro100: replace g_malloc()+memcpy() with g_memdup()
test-iov: replace g_malloc()+memcpy() with g_memdup()
i386: replace g_malloc()+memcpy() with g_memdup()
i386: introduce ELF_NOTE_SIZE macro
decnumber: use DIV_ROUND_UP
kvm: use DIV_ROUND_UP
i386/dump: use DIV_ROUND_UP
ppc: use DIV_ROUND_UP
msix: use DIV_ROUND_UP
usb-hub: use DIV_ROUND_UP
q35: use DIV_ROUND_UP
piix: use DIV_ROUND_UP
virtio-serial: use DIV_ROUND_UP
console: use DIV_ROUND_UP
monitor: use DIV_ROUND_UP
virtio-gpu: use DIV_ROUND_UP
vga: use DIV_ROUND_UP
ui: use DIV_ROUND_UP
vnc: use DIV_ROUND_UP
vvfat: use DIV_ROUND_UP
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Factour out a common pattern to compute the ELF note size.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
I used the clang-tidy qemu-round check to generate the fix:
https://github.com/elmarco/clang-tools-extra
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
I used the clang-tidy qemu-round check to generate the fix:
https://github.com/elmarco/clang-tools-extra
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Richard Henderson <rth@twiddle.net>
I used the clang-tidy qemu-round check (with the option OnlyAlignUp)
to generate the fix:
https://github.com/elmarco/clang-tools-extra
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Let's reshuffle the function prototypes so we get a cleaner outline
of the files.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170818114353.13455-19-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Let's do it just like the other architectures. Introduce kvm-stub.c
for stubs and kvm_s390x.h for the declarations.
Change license to GPL2+ and keep copyright notice.
As we are dropping the sysemu/kvm.h include from cpu.h, fix up includes.
Suggested-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170818114353.13455-18-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Let's just introduce an helper.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170818114353.13455-17-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Prepare to move more stuff (especially KVM related) from cpu.h to
internal.h.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170818114353.13455-16-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
cpu.h should only contain what really has to be accessed outside of
target/s390x/. Add internal.h which can only be used inside target/s390x/.
Move everything that isn't fast enough to run away and restructure it
right away. We'll move all kvm_* stuff later.
Minor style fixes to avoid checkpatch warning to:
- struct Lowcore: "{" goes into same line as typedef
- struct LowCore: add spaces around "-" in array length calculations
- time2tod() and tod2time(): move "{" to separate line
- get_per_atmid(): add space between ")" and "?". Move cases by one char.
- get_per_atmid(): drop extra paremthesis around (1 << 6)
Change license of new file to GPL2+ and keep copyright notice.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170818114353.13455-15-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Only used in that file.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170818114353.13455-14-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Only used in that file. Also drop the comment, not really needed.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20170818114353.13455-13-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Peter Maydell
Richard Henderson
Lluís Vilanova
Richard Henderson
Andrew Jones
Marc-André Lureau
Igor Mammedov
Brijesh Singh
Yi Wang
David Hildenbrand