The watchdog is part of NPCM7XX's timer module. Its behavior is
controlled by the WTCR register in the timer.
When enabled, the watchdog issues an interrupt signal after a pre-set
amount of cycles, and issues a reset signal shortly after that.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: deleted blank line at end of npcm_watchdog_timer-test.c]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This allows us to reuse npcm7xx_timer_pause for the watchdog timer.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
hw_error() is marked as QEMU_NORETURN, so the "break" statements
after this function are just dead code.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20201020153935.54315-4-thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
When compiling with -Werror=implicit-fallthrough, gcc complains about
missing fallthrough annotations in this file. Looking at the code,
the fallthrough is very likely intended here, so add some comments
to silence the compiler warnings.
Fixes: cd1a3f6840 ("Stand-alone TMU emulation code")
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20201020153935.54315-3-thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Replace TAB characters with spaces, put code after case-statement on
separate lines and add some curly braces in related lines to keep
checkpatch.pl happy.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20201020153935.54315-2-thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This peripheral has 1 free-running timer and 4 compare registers.
Only the free-running timer is implemented. Add support the
COMPARE registers (each register is wired to an IRQ).
Reference: "BCM2835 ARM Peripherals" datasheet [*]
chapter 12 "System Timer":
The System Timer peripheral provides four 32-bit timer channels
and a single 64-bit free running counter. Each channel has an
output compare register, which is compared against the 32 least
significant bits of the free running counter values. When the
two values match, the system timer peripheral generates a signal
to indicate a match for the appropriate channel. The match signal
is then fed into the interrupt controller.
This peripheral is used since Linux 3.7, commit ee4af5696720
("ARM: bcm2835: add system timer").
[*] https://www.raspberrypi.org/app/uploads/2012/02/BCM2835-ARM-Peripherals.pdf
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-id: 20201010203709.3116542-4-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The variable holding the CTRL_STATUS register is misnamed
'status'. Rename it 'ctrl_status' to make it more obvious
this register is also used to control the peripheral.
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201010203709.3116542-3-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use the BCM2835_SYSTIMER_COUNT definition instead of the
magic '4' value.
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201010203709.3116542-2-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Fix compiler errors when compiling with -DHPET_DEBUG due to mismatch
between format string token "%x" and the argument type uint64_t.
Also "%#x" is replaced by "0x%" PRIx64 according to the coding style.
Signed-off-by: Dov Murik <dovmurik@linux.vnet.ibm.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200909083650.46771-3-dovmurik@linux.vnet.ibm.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Fix compiler error about defined but not used functions when compiling
with -DHPET_DEBUG by deleting the unused debug functions hpet_ram_readb
and hpet_ram_readw.
Signed-off-by: Dov Murik <dovmurik@linux.vnet.ibm.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200909083650.46771-2-dovmurik@linux.vnet.ibm.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The NPCM730 and NPCM750 SoCs have three timer modules each holding five
timers and some shared registers (e.g. interrupt status).
Each timer runs at 25 MHz divided by a prescaler, and counts down from a
configurable initial value to zero. When zero is reached, the interrupt
flag for the timer is set, and the timer is disabled (one-shot mode) or
reloaded from its initial value (periodic mode).
This implementation is sufficient to boot a Linux kernel configured for
NPCM750. Note that the kernel does not seem to actually turn on the
interrupts.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Message-id: 20200911052101.2602693-4-hskinnemoen@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
It is the responsibility of board code for an armv7m system to set
system_clock_scale appropriately for the CPU speed of the core.
If it forgets to do this, then QEMU will hang if the guest tries
to use the systick timer in the "tick at the CPU clock frequency" mode.
We forgot that in a couple of our boards (see commits ce4f70e81e,
e7e5a9595a). Add an assertion in the systick reset method so
we don't let any new boards in with the same bug.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200825160847.18091-1-peter.maydell@linaro.org
Tracked down with the help of scripts/cleanup-trace-events.pl.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-id: 20200806141334.3646302-4-armbru@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Some typedefs and macros are defined after the type check macros.
This makes it difficult to automatically replace their
definitions with OBJECT_DECLARE_TYPE.
Patch generated using:
$ ./scripts/codeconverter/converter.py -i \
--pattern=QOMStructTypedefSplit $(git grep -l '' -- '*.[ch]')
which will split "typdef struct { ... } TypedefName"
declarations.
Followed by:
$ ./scripts/codeconverter/converter.py -i --pattern=MoveSymbols \
$(git grep -l '' -- '*.[ch]')
which will:
- move the typedefs and #defines above the type check macros
- add missing #include "qom/object.h" lines if necessary
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-9-ehabkost@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-10-ehabkost@redhat.com>
Message-Id: <20200831210740.126168-11-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Meson doesn't enjoy the same flexibility we have with Make in choosing
the include path. In particular the tracing headers are using
$(build_root)/$(<D).
In order to keep the include directives unchanged,
the simplest solution is to generate headers with patterns like
"trace/trace-audio.h" and place forwarding headers in the source tree
such that for example "audio/trace.h" includes "trace/trace-audio.h".
This patch is too ugly to be applied to the Makefiles now. It's only
a way to separate the changes to the tracing header files from the
Meson rewrite of the tracing logic.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The imx_epit device has a software-controllable reset triggered by
setting the SWR bit in the CR register. An error in commit cc2722ec83
means that we will end up assert()ing if the guest does this, because
the code in imx_epit_write() starts ptimer transactions, and then
imx_epit_reset() also starts ptimer transactions, triggering
"ptimer_transaction_begin: Assertion `!s->in_transaction' failed".
The cleanest way to avoid this double-transaction is to move the
start-transaction for the CR write handling down below the check of
the SWR bit.
Fixes: https://bugs.launchpad.net/qemu/+bug/1880424
Fixes: cc2722ec83
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20200727154550.3409-1-peter.maydell@linaro.org
These were designed to facilitate testing but should provide enough
function to be useful in other contexts. Only a subset of the functions
of each peripheral is implemented, mainly due to the lack of a standard
way to handle electrical connections (like GPIO pins).
[AM: Remove word 'Atmel' from filenames and all elements of code]
Suggested-by: Aleksandar Markovic <aleksandar.m.mail@gmail.com>
Signed-off-by: Sarah Harris <S.E.Harris@kent.ac.uk>
Signed-off-by: Ed Robbins <E.J.C.Robbins@kent.ac.uk>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
[rth: Squash info mtree fixes and a file rename from f4bug]
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
[PMD: Use qemu_log_mask(LOG_UNIMP), replace goto by return]
Signed-off-by: Aleksandar Markovic <aleksandar.m.mail@gmail.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Thomas Huth <huth@tuxfamily.org>
Message-Id: <20200705140315.260514-21-huth@tuxfamily.org>
[PMD: Check cpu-frequency-hz property in realize()]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
renesas_cmt: 16bit compare match timer modules.
This part use many renesas's CPU.
Hardware manual.
https://www.renesas.com/us/en/doc/products/mpumcu/doc/rx_family/r01uh0033ej0140_rx62n.pdf
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20200224141923.82118-16-ysato@users.sourceforge.jp>
[PMD: Split from TMR, filled VMStateField for migration]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
renesas_tmr: 8bit timer modules.
This part use many renesas's CPU.
Hardware manual.
https://www.renesas.com/us/en/doc/products/mpumcu/doc/rx_family/r01uh0033ej0140_rx62n.pdf
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20200224141923.82118-16-ysato@users.sourceforge.jp>
[PMD: Split from CMT, filled VMStateField for migration]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Extract timer definitions to 'hw/timer/tmu012.h'.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Convert DPRINTF() to traces or qemu_logs
Use IEC binary prefix definitions
Use qemu_semihosting_log_out() in target/unicore32
Some code and doc cleanup
-----BEGIN PGP SIGNATURE-----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=jkE3
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/vivier2/tags/trivial-branch-for-5.1-pull-request' into staging
Trivial branch pull request 20200610
Convert DPRINTF() to traces or qemu_logs
Use IEC binary prefix definitions
Use qemu_semihosting_log_out() in target/unicore32
Some code and doc cleanup
# gpg: Signature made Wed 10 Jun 2020 14:08:36 BST
# gpg: using RSA key CD2F75DDC8E3A4DC2E4F5173F30C38BD3F2FBE3C
# gpg: issuer "laurent@vivier.eu"
# gpg: Good signature from "Laurent Vivier <lvivier@redhat.com>" [full]
# gpg: aka "Laurent Vivier <laurent@vivier.eu>" [full]
# gpg: aka "Laurent Vivier (Red Hat) <lvivier@redhat.com>" [full]
# Primary key fingerprint: CD2F 75DD C8E3 A4DC 2E4F 5173 F30C 38BD 3F2F BE3C
* remotes/vivier2/tags/trivial-branch-for-5.1-pull-request:
semihosting: remove the pthread include which seems unused
hw/openrisc/openrisc_sim: Add assertion to silence GCC warning
target/unicore32: Prefer qemu_semihosting_log_out() over curses
target/unicore32: Replace DPRINTF() by qemu_log_mask(GUEST_ERROR)
target/unicore32: Remove unused headers
target/i386/cpu: Use the IEC binary prefix definitions
hw/i386/xen/xen-hvm: Use the IEC binary prefix definitions
hw/hppa/dino: Use the IEC binary prefix definitions
hw/arm/aspeed: Correct DRAM container region size
qemu-img: Fix doc typo for 'bitmap' subcommand
hw/misc/auxbus: Use qemu_log_mask(UNIMP) instead of debug printf
hw/isa/apm: Convert debug printf()s to trace events
hw/unicore32/puv3: Use qemu_log_mask(ERROR) instead of debug printf()
.mailmap: Update Fred Konrad email address
net: Do not include a newline in the id of -nic devices
Fix parameter type in vhost migration log path
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
# Conflicts:
# .mailmap
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: KONRAD Frederic <frederic.konrad@adacore.com>
Message-Id: <20200331105048.27989-6-f4bug@amsat.org>
hw_error() calls exit(). This a bit overkill when we can log
the accesses as unimplemented or guest error.
When fuzzing the devices, we don't want the whole process to
exit. Replace some hw_error() calls by qemu_log_mask().
Per the datasheet "Exynos 4412 RISC Microprocessor Rev 1.00"
Chapter 25 "Multi Core Timer (MCT)" figure 1 and table 4,
the default value on the APB bus is 0.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20200518140309.5220-5-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add trace event to display timer's counter value updates.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200504072822.18799-5-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The NRF51 series SoC have 3 timer peripherals, each having
4 counters. To help differentiate which peripheral is accessed,
display the timer ID in the trace events.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200504072822.18799-4-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
On the NRF51 series, all peripherals have a fixed I/O size
of 4KiB. Define NRF51_PERIPHERAL_SIZE and use it.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200504072822.18799-2-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Fix warning reported by Clang static code analyzer:
CC hw/timer/stm32f2xx_timer.o
hw/timer/stm32f2xx_timer.c:225:9: warning: Value stored to 'value' is never read
value = timer_val;
^ ~~~~~~~~~
Reported-by: Clang Static Analyzer
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200422133152.16770-9-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Clang static code analyzer show warning:
hw/timer/exynos4210_mct.c:1370:9: warning: Value stored to 'index' is never read
index = GET_L_TIMER_CNT_REG_IDX(offset, lt_i);
^ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
hw/timer/exynos4210_mct.c:1399:9: warning: Value stored to 'index' is never read
index = GET_L_TIMER_CNT_REG_IDX(offset, lt_i);
^ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
hw/timer/exynos4210_mct.c:1441:9: warning: Value stored to 'index' is never read
index = GET_L_TIMER_CNT_REG_IDX(offset, lt_i);
^ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Chen Qun <kuhn.chenqun@huawei.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200325025919.21316-4-kuhn.chenqun@huawei.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
hw/timer/hpet.c calls address_space_stl_le() declared in
"exec/address-spaces.h". Include it.
This fixes (when modifying unrelated headers):
hw/timer/hpet.c:210:31: error: use of undeclared identifier 'address_space_memory'
address_space_stl_le(&address_space_memory, timer->fsb >> 32,
^~~~~~~~~~~~~~~~~~~~
Acked-by: John Snow <jsnow@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20200228114649.12818-12-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The timer models don't need anything from "ui/console.h".
Remove it.
Acked-by: John Snow <jsnow@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20200228114649.12818-5-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
There are some memleaks when we call 'device_list_properties'. This patch move timer_new from init into realize to fix it.
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Pan Nengyuan <pannengyuan@huawei.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20200227025055.14341-7-pannengyuan@huawei.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There is a memory leak when we call 'device_list_properties' with typename = stm32f2xx_timer. It's easy to reproduce as follow:
virsh qemu-monitor-command vm1 --pretty '{"execute": "device-list-properties", "arguments": {"typename": "stm32f2xx_timer"}}'
This patch delay timer_new to fix this memleaks.
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Pan Nengyuan <pannengyuan@huawei.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20200205070659.22488-3-pannengyuan@huawei.com
Cc: Alistair Francis <alistair@alistair23.me>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There is a memory leak when we call 'device_list_properties' with typename = armv7m_systick. It's easy to reproduce as follow:
virsh qemu-monitor-command vm1 --pretty '{"execute": "device-list-properties", "arguments": {"typename": "armv7m_systick"}}'
This patch delay timer_new to fix this memleaks.
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Pan Nengyuan <pannengyuan@huawei.com>
Message-id: 20200205070659.22488-2-pannengyuan@huawei.com
Cc: qemu-arm@nongnu.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reported by GCC9 when building with CFLAG -Wimplicit-fallthrough=2:
hw/timer/aspeed_timer.c: In function ‘aspeed_timer_set_value’:
hw/timer/aspeed_timer.c:283:24: error: this statement may fall through [-Werror=implicit-fallthrough=]
283 | if (old_reload || !t->reload) {
| ~~~~~~~~~~~^~~~~~~~~~~~~
hw/timer/aspeed_timer.c:287:5: note: here
287 | case TIMER_REG_STATUS:
| ^~~~
cc1: all warnings being treated as errors
Add the missing fall through comment.
Fixes: 1403f36447
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20191218192526.13845-4-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Define the new macro VMSTATE_INSTANCE_ID_ANY for callers who wants to
auto-generate the vmstate instance ID. Previously it was hard coded
as -1 instead of this macro. It helps to change this default value in
the follow up patches. No functional change.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Since i8254_common.c calls isa_register_ioport() from "hw/isa/isa.h"
we can not select it when ISA_BUS is disabled. Add a 'depends on'
clause.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200106171912.16523-1-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The Aspeed Watchdog and Timer models have a link pointing to the SCU
controller model of the machine.
Change the "scu" property definition so that it explicitly sets the
pointer. The property isn't optional : not being able to set the link
is a bug and QEMU should rather abort than exit in this case.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-17-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
These devices implemented their load_state_old() handler 10 years
ago, previous to QEMU v0.12.
Since commit cc425b5ddf removed the pc-0.10 and pc-0.11 machines,
we can drop this code.
Note: the mips_r4k machine started to use the i8254 device just
after QEMU v0.5.0, but the MIPS machine types are not versioned,
so there is no migration compatibility issue removing this handler.
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Switch the milkymist-sysctl code away from bottom-half based
ptimers to the new transaction-based ptimer API. This just requires
adding begin/commit calls around the various places that modify the
ptimer state, and using the new ptimer_init() function to create the
timer.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20191021141040.11007-1-peter.maydell@linaro.org
Switch the grlib_gptimer code away from bottom-half based ptimers to
the new transaction-based ptimer API. This just requires adding
begin/commit calls around the various places that modify the ptimer
state, and using the new ptimer_init() function to create the timer.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20191021134357.14266-3-peter.maydell@linaro.org
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Switch the slavio_timer code away from bottom-half based ptimers to
the new transaction-based ptimer API. This just requires adding
begin/commit calls around the various places that modify the ptimer
state, and using the new ptimer_init() function to create the timer.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191021134357.14266-4-peter.maydell@linaro.org
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Only 2 source files require the "mc146818rtc_regs.h" header.
Instead of having it processed 12 times, by all objects
using "mc146818rtc.h", include it directly where used.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20191003230404.19384-13-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Move RTC devices under the hw/rtc/ subdirectory.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20191003230404.19384-12-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Move RTC devices under the hw/rtc/ subdirectory.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20191003230404.19384-11-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The DS1338 is a Real Time Clock, not a timer.
Move it under the hw/rtc/ subdirectory.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20191003230404.19384-9-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The TWL92230 is an "energy management device" companion with
a RTC. Since we mostly model the RTC, move it under the hw/rtc/
subdirectory.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20191003230404.19384-8-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The M41T80 is a Real Time Clock, not a timer.
Move it under the hw/rtc/ subdirectory.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20191003230404.19384-6-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The M48T59 is a Real Time Clock, not a timer.
Move it under the hw/rtc/ subdirectory.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20191003230404.19384-5-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The MC146818 is a Real Time Clock, not a timer.
Move it under the hw/rtc/ subdirectory.
Use copyright statement from 80cabfad16 for "hw/rtc/mc146818rtc.h".
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20191003230404.19384-4-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The PL031 is a Real Time Clock, not a timer.
Move it under the hw/rtc/ subdirectory.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20191003230404.19384-3-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
All these devices do not contain any target-specific. While most
of them are arch-specific, they are shared between different
targets of the same arch family (ARM and AArch64, MIPS32/MIPS64,
endianess, ...).
Put them into common-obj-y to compile them once for all targets.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20191003230404.19384-2-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
In the slavio timer device, the ptimer TimerContext::timer is
always created by slavio_timer_init(), so there's no need to
check it for NULL; remove the single unneeded NULL check.
This will be useful to avoid compiler/Coverity errors when
a subsequent change adds a use of t->timer before the location
we currently do the NULL check.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191021134357.14266-2-peter.maydell@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Switch the xilinx_timer code away from bottom-half based ptimers to
the new transaction-based ptimer API. This just requires adding
begin/commit calls around the various places that modify the ptimer
state, and using the new ptimer_init() function to create the timer.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20191017132122.4402-3-peter.maydell@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Switch the etraxfs_timer code away from bottom-half based ptimers to
the new transaction-based ptimer API. This just requires adding
begin/commit calls around the various places that modify the ptimer
state, and using the new ptimer_init() function to create the timer.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20191017132905.5604-7-peter.maydell@linaro.org
Switch the altera_timer code away from bottom-half based ptimers to
the new transaction-based ptimer API. This just requires adding
begin/commit calls around the various places that modify the ptimer
state, and using the new ptimer_init() function to create the timer.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20191017132905.5604-6-peter.maydell@linaro.org
Switch the lm32_timer code away from bottom-half based ptimers to the
new transaction-based ptimer API. This just requires adding
begin/commit calls around the various places that modify the ptimer
state, and using the new ptimer_init() function to create the ytimer.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20191017132905.5604-4-peter.maydell@linaro.org
Switch the sh_timer code away from bottom-half based ptimers to the
new transaction-based ptimer API. This just requires adding
begin/commit calls around the various places that modify the ptimer
state, and using the new ptimer_init() function to create the timer.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20191017132905.5604-3-peter.maydell@linaro.org
Switch the puv3_ost code away from bottom-half based ptimers to the
new transaction-based ptimer API. This just requires adding
begin/commit calls around the various places that modify the ptimer
state, and using the new ptimer_init() function to create the timer.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20191017132905.5604-2-peter.maydell@linaro.org
In commit b01422622b we did an automated rename of the ptimer_init()
function to ptimer_init_with_bh(). Unfortunately this caught the
unrelated arm_mptimer_init() function. Undo that accidental
renaming.
Fixes: b01422622b
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20191017133331.5901-1-peter.maydell@linaro.org
When booting a recent Linux kernel, the qemu message "Timer with delta
zero, disabling" is seen, apparently because a ptimer is started before
being initialized. Fix the problem by initializing the offending ptimer
before starting it.
The bug is effectively harmless in the old QEMUBH setup
because the sequence of events is:
* the delta zero means the timer expires immediately
* ptimer_reload() arranges for exynos4210_gfrc_event() to be called
* ptimer_reload() notices the zero delta and disables the timer
* later, the QEMUBH runs, and exynos4210_gfrc_event() correctly
configures the timer and restarts it
In the new transaction based API the bug is still harmless,
but differences of when the callback function runs mean the
message is not printed any more:
* ptimer_run() does nothing as it's inside a transaction block
* ptimer_transaction_commit() sees it has work to do and
calls ptimer_reload()
* the zero delta means the timer expires immediately
* ptimer_reload() calls exynos4210_gfrc_event() directly
* exynos4210_gfrc_event() configures the timer
* the delta is no longer zero so ptimer_reload() doesn't complain
(the zero-delta test is after the trigger-callback in
the ptimer_reload() function)
Regardless, the behaviour here was not intentional, and we should
just program the ptimer correctly to start with.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20191018143149.9216-1-peter.maydell@linaro.org
[PMM: Expansion/clarification of the commit message:
the message is about a zero delta, not a zero period;
added detail to the commit message of the analysis of what
is happening and why the kernel boots even with the message;
added note that the message goes away with the new ptimer API]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The AST2600 timer replaces control register 2 with a interrupt status
register. It is set by hardware when an IRQ occurs and cleared by
software.
Modify the vmstate version to take into account the new fields.
Based on previous work from Joel Stanley.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190925143248.10000-8-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The AST2600 timer has a third control register that is used to
implement a set-to-clear feature for the main control register.
On the AST2600, it is not configurable via 0x38 (control register 3)
as it is on the AST2500.
Based on previous work from Joel Stanley.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190925143248.10000-7-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The AST2500 timer has a third control register that is used to
implement a set-to-clear feature for the main control register.
This models the behaviour expected by the AST2500 while maintaining
the same behaviour for the AST2400.
The vmstate version is not increased yet because the structure is
modified again in the following patches.
Based on previous work from Joel Stanley.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190925143248.10000-6-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The most important changes will be on the register range 0x34 - 0x3C
memops. Introduce class read/write operations to handle the
differences between SoCs.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190925143248.10000-5-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Switch the mss-timer code away from bottom-half based ptimers to
the new transaction-based ptimer API. This just requires adding
begin/commit calls around the various places that modify the ptimer
state, and using the new ptimer_init() function to create the timer.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191008171740.9679-20-peter.maydell@linaro.org
Switch the imx_epit.c code away from bottom-half based ptimers to
the new transaction-based ptimer API. This just requires adding
begin/commit calls around the various places that modify the ptimer
state, and using the new ptimer_init() function to create the timer.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191008171740.9679-19-peter.maydell@linaro.org
Switch the imx_epit.c code away from bottom-half based ptimers to
the new transaction-based ptimer API. This just requires adding
begin/commit calls around the various places that modify the ptimer
state, and using the new ptimer_init() function to create the timer.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191008171740.9679-18-peter.maydell@linaro.org
Switch the exynos41210_rtc main ptimer over to the transaction-based
API, completing the transition for this device.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191008171740.9679-17-peter.maydell@linaro.org
Switch the exynos41210_rtc 1Hz ptimer over to the transaction-based
API. (We will switch the other ptimer used by this device in a
separate commit.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191008171740.9679-16-peter.maydell@linaro.org
Switch the exynos4210_pwm code away from bottom-half based ptimers to
the new transaction-based ptimer API. This just requires adding
begin/commit calls around the various places that modify the ptimer
state, and using the new ptimer_init() function to create the timer.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191008171740.9679-15-peter.maydell@linaro.org
Switch the ltick ptimer over to the ptimer transaction API.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191008171740.9679-14-peter.maydell@linaro.org
Switch the exynos MCT LFRC timers over to the ptimer transaction API.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191008171740.9679-13-peter.maydell@linaro.org
We want to switch the exynos MCT code away from bottom-half based ptimers to
the new transaction-based ptimer API. The MCT is complicated
and uses multiple different ptimers, so it's clearer to switch
it a piece at a time. Here we change over only the GFRC.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191008171740.9679-12-peter.maydell@linaro.org
Switch the digic-timer.c code away from bottom-half based ptimers to
the new transaction-based ptimer API. This just requires adding
begin/commit calls around the various places that modify the ptimer
state, and using the new ptimer_init() function to create the timer.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191008171740.9679-11-peter.maydell@linaro.org
Switch the cmsdk-apb-timer code away from bottom-half based ptimers
to the new transaction-based ptimer API. This just requires adding
begin/commit calls around the various places that modify the ptimer
state, and using the new ptimer_init() function to create the timer.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191008171740.9679-10-peter.maydell@linaro.org
Switch the cmsdk-apb-dualtimer code away from bottom-half based
ptimers to the new transaction-based ptimer API. This just requires
adding begin/commit calls around the various places that modify the
ptimer state, and using the new ptimer_init() function to create the
timer.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191008171740.9679-9-peter.maydell@linaro.org
Switch the arm_mptimer.c code away from bottom-half based ptimers to
the new transaction-based ptimer API. This just requires adding
begin/commit calls around the various places that modify the ptimer
state, and using the new ptimer_init() function to create the timer.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191008171740.9679-8-peter.maydell@linaro.org
Switch the allwinner-a10-pit code away from bottom-half based ptimers to
the new transaction-based ptimer API. This just requires adding
begin/commit calls around the various places that modify the ptimer
state, and using the new ptimer_init() function to create the timer.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191008171740.9679-7-peter.maydell@linaro.org
Switch the arm_timer.c code away from bottom-half based ptimers
to the new transaction-based ptimer API. This just requires
adding begin/commit calls around the various arms of
arm_timer_write() that modify the ptimer state, and using the
new ptimer_init() function to create the timer.
Fixes: https://bugs.launchpad.net/qemu/+bug/1777777
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191008171740.9679-5-peter.maydell@linaro.org
Currently the ptimer design uses a QEMU bottom-half as its
mechanism for calling back into the device model using the
ptimer when the timer has expired. Unfortunately this design
is fatally flawed, because it means that there is a lag
between the ptimer updating its own state and the device
callback function updating device state, and guest accesses
to device registers between the two can return inconsistent
device state.
We want to replace the bottom-half design with one where
the guest device's callback is called either immediately
(when the ptimer triggers by timeout) or when the device
model code closes a transaction-begin/end section (when the
ptimer triggers because the device model changed the
ptimer's count value or other state). As the first step,
rename ptimer_init() to ptimer_init_with_bh(), to free up
the ptimer_init() name for the new API. We can then convert
all the ptimer users away from ptimer_init_with_bh() before
removing it entirely.
(Commit created with
git grep -l ptimer_init | xargs sed -i -e 's/ptimer_init/ptimer_init_with_bh/'
and three overlong lines folded by hand.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191008171740.9679-2-peter.maydell@linaro.org
Bottom halves and ptimers are malloced, but nothing in these
files is freeing memory allocated by instance_init. Since
these are sysctl devices that are never unrealized, just moving
the allocations to realize is enough to avoid the leak in
practice (and also to avoid upsetting asan when running
device-introspect-test).
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
The APB frequency can be calculated directly when needed from the
HPLL_PARAM and CLK_SEL register values. This removes useless state in
the model.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20190904070506.1052-11-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
First up: This is not the way the hardware behaves.
However, it helps resolve real-world problems with short periods being
used under Linux. Commit 4451d3f59f2a ("clocksource/drivers/fttmr010:
Fix set_next_event handler") in Linux fixed the timer driver to
correctly schedule the next event for the Aspeed controller, and in
combination with 5daa8212c08e ("ARM: dts: aspeed: Describe random number
device") Linux will now set a timer with a period as low as 1us.
Configuring a qemu timer with such a short period results in spending
time handling the interrupt in the model rather than executing guest
code, leading to noticeable "sticky" behaviour in the guest.
The behaviour of Linux is correct with respect to the hardware, so we
need to improve our handling under emulation. The approach chosen is to
provide back-pressure information by calculating an acceptable minimum
number of ticks to be set on the model. Under Linux an additional read
is added in the timer configuration path to detect back-pressure, which
will never occur on hardware. However if back-pressure is observed, the
driver alerts the clock event subsystem, which then performs its own
next event dilation via a config option - d1748302f70b ("clockevents:
Make minimum delay adjustments configurable")
A minimum period of 5us was experimentally determined on a Lenovo
T480s, which I've increased to 20us for "safety".
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20190704055150.4899-1-clg@kaod.org
[clg: - changed the computation of min_ticks to be done each time the
timer value is reloaded. It removes the ordering issue of the
timer and scu reset handlers but is slightly slower ]
- introduced TIMER_MIN_NS
- introduced calculate_min_ticks() ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Suggested-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190709152053.16670-2-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[Rebased onto merge commit 95a9457fd44; missed instances of qom/cpu.h
in comments replaced]
The reset notifiers are unreliable and recalculating the offsets
after boot causes problems with migration in cases where explicit
base times are set on the destination.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20190724115823.4199-2-dgilbert@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The XLNX_ZYNQMP config is used in multiple subdirectories
(timer, intc). Move it to the root hw/Kconfig.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190427141459.19728-2-philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
sysemu/sysemu.h is a rather unfocused dumping ground for stuff related
to the system-emulator. Evidence:
* It's included widely: in my "build everything" tree, changing
sysemu/sysemu.h still triggers a recompile of some 1100 out of 6600
objects (not counting tests and objects that don't depend on
qemu/osdep.h, down from 5400 due to the previous two commits).
* It pulls in more than a dozen additional headers.
Split stuff related to run state management into its own header
sysemu/runstate.h.
Touching sysemu/sysemu.h now recompiles some 850 objects. qemu/uuid.h
also drops from 1100 to 850, and qapi/qapi-types-run-state.h from 4400
to 4200. Touching new sysemu/runstate.h recompiles some 500 objects.
Since I'm touching MAINTAINERS to add sysemu/runstate.h anyway, also
add qemu/main-loop.h.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190812052359.30071-30-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
[Unbreak OS-X build]
In my "build everything" tree, changing sysemu/sysemu.h triggers a
recompile of some 5400 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
Almost a third of its inclusions are actually superfluous. Delete
them. Downgrade two more to qapi/qapi-types-run-state.h, and move one
from char/serial.h to char/serial.c.
hw/semihosting/config.c, monitor/monitor.c, qdev-monitor.c, and
stubs/semihost.c define variables declared in sysemu/sysemu.h without
including it. The compiler is cool with that, but include it anyway.
This doesn't reduce actual use much, as it's still included into
widely included headers. The next commit will tackle that.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-27-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
In my "build everything" tree, changing hw/qdev-properties.h triggers
a recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
Many places including hw/qdev-properties.h (directly or via hw/qdev.h)
actually need only hw/qdev-core.h. Include hw/qdev-core.h there
instead.
hw/qdev.h is actually pointless: all it does is include hw/qdev-core.h
and hw/qdev-properties.h, which in turn includes hw/qdev-core.h.
Replace the remaining uses of hw/qdev.h by hw/qdev-properties.h.
While there, delete a few superfluous inclusions of hw/qdev-core.h.
Touching hw/qdev-properties.h now recompiles some 1200 objects.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Daniel P. Berrangé" <berrange@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190812052359.30071-22-armbru@redhat.com>
In my "build everything" tree, changing qemu/main-loop.h triggers a
recompile of some 5600 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h). It includes block/aio.h,
which in turn includes qemu/event_notifier.h, qemu/notify.h,
qemu/processor.h, qemu/qsp.h, qemu/queue.h, qemu/thread-posix.h,
qemu/thread.h, qemu/timer.h, and a few more.
Include qemu/main-loop.h only where it's needed. Touching it now
recompiles only some 1700 objects. For block/aio.h and
qemu/event_notifier.h, these numbers drop from 5600 to 2800. For the
others, they shrink only slightly.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190812052359.30071-21-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing hw/hw.h triggers a recompile
of some 2600 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
The previous commits have left only the declaration of hw_error() in
hw/hw.h. This permits dropping most of its inclusions. Touching it
now recompiles less than 200 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-19-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing migration/vmstate.h triggers a
recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get VMStateDescription. The previous commit made
that unnecessary.
Include migration/vmstate.h only where it's still needed. Touching it
now recompiles only some 1600 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-16-armbru@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing hw/irq.h triggers a recompile
of some 5400 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get qemu_irq and.or qemu_irq_handler.
Move the qemu_irq and qemu_irq_handler typedefs from hw/irq.h to
qemu/typedefs.h, and then include hw/irq.h only where it's still
needed. Touching it now recompiles only some 500 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-13-armbru@redhat.com>
In my "build everything" tree, changing migration/qemu-file-types.h
triggers a recompile of some 2600 out of 6600 objects (not counting
tests and objects that don't depend on qemu/osdep.h).
The culprit is again hw/hw.h, which supposedly includes it for
convenience.
Include migration/qemu-file-types.h only where it's needed. Touching
it now recompiles less than 200 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190812052359.30071-10-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
In my "build everything" tree, changing sysemu/reset.h triggers a
recompile of some 2600 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
The main culprit is hw/hw.h, which supposedly includes it for
convenience.
Include sysemu/reset.h only where it's needed. Touching it now
recompiles less than 200 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-9-armbru@redhat.com>
The PL031 RTC tracks the difference between the guest RTC
and the host RTC using a tick_offset field. For migration,
however, we currently always migrate the offset between
the guest and the vm_clock, even if the RTC clock is not
the same as the vm_clock; this was an attempt to retain
migration backwards compatibility.
Unfortunately this results in the RTC behaving oddly across
a VM state save and restore -- since the VM clock stands still
across save-then-restore, regardless of how much real world
time has elapsed, the guest RTC ends up out of sync with the
host RTC in the restored VM.
Fix this by migrating the raw tick_offset. To retain migration
compatibility as far as possible, we have a new property
migrate-tick-offset; by default this is 'true' and we will
migrate the true tick offset in a new subsection; if the
incoming data has no subsection we fall back to the old
vm_clock-based offset information, so old->new migration
compatibility is preserved. For complete new->old migration
compatibility, the property is set to 'false' for 4.0 and
earlier machine types (this will only affect 'virt-4.0'
and below, as none of the other pl031-using machines are
versioned).
Reported-by: Russell King <rmk@armlinux.org.uk>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-id: 20190709143912.28905-1-peter.maydell@linaro.org
Like most of the v7M memory mapped system registers, the systick
registers are accessible to privileged code only and user accesses
must generate a BusFault. We implement that for registers in
the NVIC proper already, but missed it for systick since we
implement it as a separate device. Correct the omission.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190617175317.27557-6-peter.maydell@linaro.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190619201050.19040-14-armbru@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
If the host decrements the counter register that results in a negative
delta. This is then passed to muldiv64 which only handles unsigned
numbers resulting in bogus results.
This fix ensures the delta being operated on is positive.
Test case: kexec a kernel using aspeed_timer and it will freeze on the
second bootup when the kernel initializes the timer. With this patch
that no longer happens and the timer appears to run OK.
Signed-off-by: Christian Svensson <bluecmd@google.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 20190618165311.27066-12-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If the match value exceeds reload then we don't want to include it in
calculations for the next event.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20190618165311.27066-10-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
From the datasheet:
This register stores the current status of counter #N. When timer
enable bit TMC30[N * b] is disabled, the reload register will be
loaded into this counter. When timer bit TMC30[N * b] is set, the
counter will start to decrement. CPU can update this register value
when enable bit is set.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190618165311.27066-9-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Linux kernel driver was updated in commit 4451d3f59f2a
("clocksource/drivers/fttmr010: Fix set_next_event handler) to fix an
issue observed on hardware:
> RELOAD register is loaded into COUNT register when the aspeed timer
> is enabled, which means the next event may be delayed because timer
> interrupt won't be generated until <0xFFFFFFFF - current_count +
> cycles>.
When running under Qemu, the system appeared "laggy". The guest is now
scheduling timer events too regularly, starving the host of CPU time.
This patch modifies the timer model to attempt to schedule the timer
expiry as the guest requests, but if we have missed the deadline we
re interrupt and try again, which allows the guest to catch up.
Provides expected behaviour with old and new guest code.
Fixes: c04bd47db6 ("hw/timer: Add ASPEED timer device model")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20190618165311.27066-8-clg@kaod.org
[clg: - merged a fix from Andrew Jeffery <andrew@aj.id.au>
"Fire interrupt on failure to meet deadline"
https://lists.ozlabs.org/pipermail/openbmc/2019-January/014641.html
- adapted commit log
- checkpatch fixes ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The RTC is modeled to provide time and date functionality. It is
initialised at zero to match the hardware.
There is no modelling of the alarm functionality, which includes the IRQ
line. As there is no guest code to exercise this function that is
acceptable for now.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20190618165311.27066-4-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
No header includes qemu-common.h after this commit, as prescribed by
qemu-common.h's file comment.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190523143508.25387-5-armbru@redhat.com>
[Rebased with conflicts resolved automatically, except for
include/hw/arm/xlnx-zynqmp.h hw/arm/nrf51_soc.c hw/arm/msf2-soc.c
block/qcow2-refcount.c block/qcow2-cluster.c block/qcow2-cache.c
target/arm/cpu.h target/lm32/cpu.h target/m68k/cpu.h target/mips/cpu.h
target/moxie/cpu.h target/nios2/cpu.h target/openrisc/cpu.h
target/riscv/cpu.h target/tilegx/cpu.h target/tricore/cpu.h
target/unicore32/cpu.h target/xtensa/cpu.h; bsd-user/main.c and
net/tap-bsd.c fixed up]
Suggested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: KONRAD Frederic <frederic.konrad@adacore.com>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
We commonly define the header guard symbol without an explicit value.
Normalize the exceptions.
Done with scripts/clean-header-guards.pl.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190315145123.28030-8-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190417190641.26814-7-armbru@redhat.com>
Some trace points are attributed to the wrong source file. Happens
when we neglect to update trace-events for code motion, or add events
in the wrong place, or misspell the file name.
Clean up with help of cleanup-trace-events.pl. Same funnies as in the
previous commit, of course. Manually shorten its change to
linux-user/trace-events to */signal.c.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-id: 20190314180929.27722-6-armbru@redhat.com
Message-Id: <20190314180929.27722-6-armbru@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
We spell out sub/dir/ in sub/dir/trace-events' comments pointing to
source files. That's because when trace-events got split up, the
comments were moved verbatim.
Delete the sub/dir/ part from these comments. Gets rid of several
misspellings.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190314180929.27722-3-armbru@redhat.com
Message-Id: <20190314180929.27722-3-armbru@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
%-softmmu.mak only keep boards definitions in Kconfig mode.
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20190123065618.3520-43-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-39-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Acked-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-38-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The Kconfig files were generated mostly with this script:
for i in `grep -ho CONFIG_[A-Z0-9_]* default-configs/* | sort -u`; do
set fnord `git grep -lw $i -- 'hw/*/Makefile.objs' `
shift
if test $# = 1; then
cat >> $(dirname $1)/Kconfig << EOF
config ${i#CONFIG_}
bool
EOF
git add $(dirname $1)/Kconfig
else
echo $i $*
fi
done
sed -i '$d' hw/*/Kconfig
for i in hw/*; do
if test -d $i && ! test -f $i/Kconfig; then
touch $i/Kconfig
git add $i/Kconfig
fi
done
Whenever a symbol is referenced from multiple subdirectories, the
script prints the list of directories that reference the symbol.
These symbols have to be added manually to the Kconfig files.
Kconfig.host and hw/Kconfig were created manually.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20190123065618.3520-27-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It is never supposed to fail and cannot return an error, so just
have it return the proper type. Have it return 0xff on nothing
available, since that's what would happen on a real bus.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Convert the debug printing in the PL031 device to use trace events,
and augment it to cover the interesting parts of device operation.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Create a new include file for the pl031's device struct,
type macros, etc, so that it can be instantiated using
the "embedded struct" coding style.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
A few targets don't emit RTC_CHANGE, we could restrict the event to
the tagets that do emit it.
Note: There is a lot more of events & commands that we could restrict
to capable targets, with the cost of some additional complexity, but
the benefit of added correctness and better introspection.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190214152251.2073-19-armbru@redhat.com>
Move rtc-reset-reinjection and SEV in target.json and make them
conditional on TARGET_I386.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190214152251.2073-10-armbru@redhat.com>
These files don't seem to do anything related to ISA directly, so
there is no need to include isa.h here.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1546615943-16274-1-git-send-email-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
This patch adds the model for the nRF51 timer peripheral.
Currently, only the TIMER mode is implemented.
Signed-off-by: Steffen Görtz <contrib@steffen-goertz.de>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190103091119.9367-9-stefanha@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The qmp/hmp command 'system_wakeup' is simply a direct call to
'qemu_system_wakeup_request' from vl.c. This function verifies if
runstate is SUSPENDED and if the wake up reason is valid before
proceeding. However, no error or warning is thrown if any of those
pre-requirements isn't met. There is no way for the caller to
differentiate between a successful wakeup or an error state caused
when trying to wake up a guest that wasn't suspended.
This means that system_wakeup is silently failing, which can be
considered a bug. Adding error handling isn't an API break in this
case - applications that didn't check the result will remain broken,
the ones that check it will have a chance to deal with it.
Adding to that, the commit before previous created a new QMP API called
query-current-machine, with a new flag called wakeup-suspend-support,
that indicates if the guest has the capability of waking up from suspended
state. Although such guest will never reach SUSPENDED state and erroring
it out in this scenario would suffice, it is more informative for the user
to differentiate between a failure because the guest isn't suspended versus
a failure because the guest does not have support for wake up at all.
All this considered, this patch changes qmp_system_wakeup to check if
the guest is capable of waking up from suspend, and if it is suspended.
After this patch, this is the output of system_wakeup in a guest that
does not have wake-up from suspend support (ppc64):
(qemu) system_wakeup
wake-up from suspend is not supported by this guest
(qemu)
And this is the output of system_wakeup in a x86 guest that has the
support but isn't suspended:
(qemu) system_wakeup
Unable to wake up: guest is not in suspended state
(qemu)
Reported-by: Balamuruhan S <bala24@linux.vnet.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20181205194701.17836-4-danielhb413@gmail.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Use DeviceClass rather than SysBusDeviceClass in
puv3_ost_class_init().
Cc: gxt@mprc.pku.edu.cn
Signed-off-by: Mao Zhongyi <maozhongyi@cmss.chinamobile.com>
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20181130093852.20739-19-maozhongyi@cmss.chinamobile.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use DeviceClass rather than SysBusDeviceClass in
grlib_gptimer_class_init().
Cc: chouteau@adacore.com
Signed-off-by: Mao Zhongyi <maozhongyi@cmss.chinamobile.com>
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20181130093852.20739-18-maozhongyi@cmss.chinamobile.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use DeviceClass rather than SysBusDeviceClass in
etraxfs_timer_class_init().
Cc: edgar.iglesias@gmail.com
Signed-off-by: Mao Zhongyi <maozhongyi@cmss.chinamobile.com>
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20181130093852.20739-17-maozhongyi@cmss.chinamobile.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The code was converted to use sun4v_rtc_read() by mistake, fix
it.
Reported-by: David Gibson <david@gibson.dropbear.id.au>
Cc: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20181031001843.12892-1-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Because they are supposed to remain const.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20181114132931.22624-1-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The UART and timer devices for the stm32f205 were being created
with memory regions that were too large. Use the size specified
in the chip datasheet.
The old sizes were so large that the devices would overlap with
each other in the SoC memory map, so this fixes a bug that
caused odd behavior and/or crashes when trying to set up multiple
UARTs.
Signed-off-by: Seth Kintigh <skintigh@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: rephrased commit message to follow our usual standard]
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Move from the legacy SysBusDevice::init method to using DeviceState::realize.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20181002212522.23303-4-f4bug@amsat.org>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
-----BEGIN PGP SIGNATURE-----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=kPZX
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/armbru/tags/pull-error-2018-10-22' into staging
Error reporting patches for 2018-10-22
# gpg: Signature made Mon 22 Oct 2018 13:20:23 BST
# gpg: using RSA key 3870B400EB918653
# gpg: Good signature from "Markus Armbruster <armbru@redhat.com>"
# gpg: aka "Markus Armbruster <armbru@pond.sub.org>"
# Primary key fingerprint: 354B C8B3 D7EB 2A6B 6867 4E5F 3870 B400 EB91 8653
* remotes/armbru/tags/pull-error-2018-10-22: (40 commits)
error: Drop bogus "use error_setg() instead" admonitions
vpc: Fail open on bad header checksum
block: Clean up bdrv_img_create()'s error reporting
vl: Simplify call of parse_name()
vl: Fix exit status for -drive format=help
blockdev: Convert drive_new() to Error
vl: Assert drive_new() does not fail in default_drive()
fsdev: Clean up error reporting in qemu_fsdev_add()
spice: Clean up error reporting in add_channel()
tpm: Clean up error reporting in tpm_init_tpmdev()
numa: Clean up error reporting in parse_numa()
vnc: Clean up error reporting in vnc_init_func()
ui: Convert vnc_display_init(), init_keyboard_layout() to Error
ui/keymaps: Fix handling of erroneous include files
vl: Clean up error reporting in device_init_func()
vl: Clean up error reporting in parse_fw_cfg()
vl: Clean up error reporting in mon_init_func()
vl: Clean up error reporting in machine_set_property()
vl: Clean up error reporting in chardev_init_func()
qom: Clean up error reporting in user_creatable_add_opts_foreach()
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
From include/qapi/error.h:
* Pass an existing error to the caller with the message modified:
* error_propagate(errp, err);
* error_prepend(errp, "Could not frobnicate '%s': ", name);
Fei Li pointed out that doing error_propagate() first doesn't work
well when @errp is &error_fatal or &error_abort: the error_prepend()
is never reached.
Since I doubt fixing the documentation will stop people from getting
it wrong, introduce error_propagate_prepend(), in the hope that it
lures people away from using its constituents in the wrong order.
Update the instructions in error.h accordingly.
Convert existing error_prepend() next to error_propagate to
error_propagate_prepend(). If any of these get reached with
&error_fatal or &error_abort, the error messages improve. I didn't
check whether that's the case anywhere.
Cc: Fei Li <fli@suse.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20181017082702.5581-2-armbru@redhat.com>
In file included from /home/thuth/devel/qemu/hw/timer/aspeed_timer.c:16:
/home/thuth/devel/qemu/include/hw/misc/aspeed_scu.h:37:3: error:
redefinition of typedef 'AspeedSCUState' is a C11 feature
[-Werror,-Wtypedef-redefinition]
} AspeedSCUState;
^
/home/thuth/devel/qemu/include/hw/timer/aspeed_timer.h:27:31: note:
previous definition is here
typedef struct AspeedSCUState AspeedSCUState;
Reported-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180921161939.822-2-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
