The lossy option can be used to enable lossy compression
methods like gradient or jpeg. This patch disable them by
default.
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Disable JPEG compression by default and only enable it if the
VNC client has sent the requested quality.
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add gradient filter and JPEG compression with an heuristic to detect how
lossy the comppression will be. This code has been adapted from
libvncserver/tight.c.
JPEG support can be enabled/disabled at compile time with --enable-vnc-jpeg
and --disable-vnc-jpeg.
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
It reintroduces
Revert "ide save/restore pio/atapi cmd transfer fields and io buffer"
but using subsections. Added bonus is the addition of ide_dummy_transfer_stop
to transfer_end_table, that was missing.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This commit adds subsections for each device section.
Subsections is the way to handle information that don't need to be sent
to de destination of a migration because its values are not needed. It is
the way to handle optional information. Notice that only the source can
decide if the information is optional or not. The destination needs to
understand all subsections that it receives to have a sucessful load.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This reverts commit ed487bb1d6.
The conflicts are due to commit 4fc8d6711a
that is a fix to the ide_drive_pre_save() function. It reverts both
(and both are reinstantiated later in the series)
Conflicts:
hw/ide/core.c
Signed-off-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Some SW drivers dont keep track of what they've written and
depend on the HW latching write contents for later
read+modify+write sequences.
Signed-off-by: Edgar E. Iglesias <edgar@axis.com>
This patch simplifies target-i386/translate.c a bit by replacing some
code with gen_update_cc_op()
Signed-off-by: Jun Koi <junkoi2004@gmail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
we have "make cscope", therefore that makes sense to have cscope.* in
.gitignore.
Signed-off-by: Jun Koi <junkoi2004@gmail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The previous patches replaced u_int8_t, u_int16_t, u_int32_t, u_int64_t
by standard int types from stdint.h,
so we can now remove their declarations which are no longer needed.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
There is no need to have a second set of integral types.
Replace them by the standard types from stdint.h.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
There is no need to have a second set of integral types.
Replace them by the standard types from stdint.h.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
There is no need to have a second set of integral types.
Replace them by the standard types from stdint.h.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Commit 36388314fe moved most of the
interrupt logic to cpu-exec.c. Remove the remaining useless code
and fix software interrupts.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Acked-by: Edgar E. Iglesias <edgar@axis.com>
Tested-by: Edgar E. Iglesias <edgar@axis.com>
Use setcond for evaluating the condition for branches.
In the future, we could do better for branches without
delay slots.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@petalogix.com>
this patch removes unused function cpu_restore_state_copy().
Signed-off-by: Jun Koi <junkoi2004@gmail.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
This patch replaces constant value assigned for (DisasContext
*)->is_jmp with DISAS_TB_JUMP.
Signed-off-by: Jun Koi <junkoi2004@gmail.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
When hw interrupt pending bits in CP0_Cause are set, the CPU should
see the hw interrupt line as active. The CPU may or may not take the
interrupt based on internal state (global irq mask etc) but the glue
logic shouldn't care.
This fixes MIPS external hw interrupts in combination with -icount.
Signed-off-by: Edgar E. Iglesias <edgar@axis.com>
There is disagreement between microblaze glibc and the kernel
to what the third arg of signal handlers should point to.
Change QEMU linux-user to match the kernel port. glibc patches
are pending.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@petalogix.com>
Both values are only used in exec.c, so there is no need
to make them globally available.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The request completion callback of the LSI controller may start the next
request that can use the same tag as the completed one. As the latter is
still enqueued at that point, scsi_send_command will complain about the
tag reuse and cancel the completed request. That will cause a double
free later on when the completion path cleans up as well.
Fix this by dequeuing the request before invoking the callback.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
This change fixes initialization of e1000's microwire EEPROM internal
state values so that qemu's e1000 emulation works on NetBSD,
which doesn't use Intel's em driver but has its own wm driver
for the Intel i8254x Gigabit Ethernet.
Previously set_eecd() function in e1000.c clears EEPROM internal state
values on SK rising edge during CS==L, but according to FM93C06 EEPROM
(which is MicroWire compatible) data sheet, EEPROM internal status
should be cleared on CS rise edge regardless of SK input:
"... a rising edge on this (CS) signal is required to reset the internal
state-machine to accept a new cycle .."
and nothing should be changed during CS (chip select) is inactive.
Intel's em driver seems to explicitly raise SK output after CS is negated
in em_standby_eeprom() so many other OSes that use Intel's driver
don't have this problem even on the previous e1000.c implementation,
but I can't find any articles that say the MICROWIRE or EEPROM spec
requires such sequence, and actually hardware works fine without it
(i.e. real i82540EM has been working on NetBSD).
This fix also changes initialization to clear each state value in
struct eecd_state individually rather than using memset() against
the whole structre. The old_eecd member stores the last SK and CS
signal levels and it should be preserved even after reset of internal
EEPROM state to detect next signal edges for proper EEPROM emulation.
Signed-off-by: Izumi Tsutsui <tsutsui@ceres.dti.ne.jp>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Guest debugging is currently broken under CONFIG_IOTHREAD. The reason is
inconsistent or even lacking signaling the debug events from the source
VCPU to the main loop and the gdbstub.
This patch addresses the issue by pushing this signaling into a
CPUDebugExcpHandler: cpu_debug_handler is registered as first handler,
thus will be executed last after potential breakpoint emulation
handlers. It sets informs the gdbstub about the debug event source,
requests a debug exit of the main loop and stops the current VCPU. This
mechanism works both for TCG and KVM, with and without IO-thread.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
These functions are also used for kvm under !CONFIG_IOTHREAD, having
'tcg' in their name is just misleading.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
When checking for I/O events in the tcg CPU loop, make sure that we
call qemu_wait_io_event_common for all CPUs, not only the current one.
Otherwise pause_all_vcpus may lock up or run_on_cpu requests may starve.
Rename qemu_wait_io_event to qemu_tcg_wait_io_event at this chance and
purge its argument list as it has no use for it.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
If a cpu_exit request is pending, ensure that we leave the CPU loop
quickly. For this purpose, keep the global exit_request pending until
we are about to leave tcg_cpu_exec. Also, immediately break out of the
SMP loop if the request is set, do not run till the end of the chain.
This preserves the VCPU scheduling order in SMP mode.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
If a signal hit after the env->exit_request check but before cpu_exec
updated env->current_tb, cpu_unlink_tb called from the signal hander
will not unlink the current TB. This may leave us stuck in a guest loop
if no further unlink is invoked.
Fix this by reordering current_tb update and exit_request check,
additionally enforcing the correct order via a compiler barrier.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Starting with qemu -M pc-0.12 -device virtio-serial
results in
-device virtio-serial: Property 'virtio-serial-pci.max_nr_ports' not found
The property name 'max_ports' is incorrectly named 'max_nr_ports'. Fix
that.
Also fix the ppc440 machine type bamboo-0.12 which has this typo.
Reported-by: Daniel P. Berrange <berrange@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
As it is done for qemu-system with "-cpu ?", when cpu_list_id() is missing
for a target, call cpu_list() instead.
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Use empty_slot to reserve addresses for several unimplemented devices so they won't fault.
- BPP (parallel port), DBRI (audio), SX (pixel processor), and vsimms (framebuffer)
OBP for SS-20 either assumes these devices exist or probes without expecting faults.
Signed-off-by: Bob Breuer <breuerr@mc.net>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
We need to know ring layout to allocate log buffer.
So init rings first.
Also fixes a theoretical memory-leak-on-error.
https://bugzilla.redhat.com/show_bug.cgi?id=615228
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
We do range check for size, and get size as buffer,
but copy size + 4 bytes (4 is for FCS).
Let's copy size bytes but put size + 4 in length.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Corentin Chary
Juan Quintela
Anthony Liguori
Edgar E. Iglesias
Jun Koi
Shahar Havivi
Stefan Weil
Aurelien Jarno
Edgar E. Iglesias
Jan Kiszka
Izumi Tsutsui
Amit Shah
Laurent Vivier
Bob Breuer
Michael S. Tsirkin
Edgar E. Iglesias