Currently the ITS code that reads and writes DTEs uses open-coded
shift-and-mask to assemble the various fields into the 64-bit DTE
word. The names of the macros used for mask and shift values are
also somewhat inconsistent, and don't follow our usual convention
that a MASK macro should specify the bits in their place in the word.
Replace all these with use of the FIELD macro.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The MAPI command takes arguments DeviceID, EventID, ICID, and is
defined to be equivalent to MAPTI DeviceID, EventID, EventID, ICID.
(That is, where MAPTI takes an explicit pINTID, MAPI uses the EventID
as the pINTID.)
We didn't quite get this right. In particular the error checks for
MAPI include "EventID does not specify a valid LPI identifier", which
is the same as MAPTI's error check for the pINTID field. QEMU's code
skips the pINTID error check entirely in the MAPI case.
We can fix this bug and in the process simplify the code by switching
to the obvious implementation of setting pIntid = eventid early
if ignore_pInt is true.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The GITS_TYPE_PHYSICAL define is the value we set the
GITS_TYPER.Physical field to -- this is 1 to indicate that we support
physical LPIs. (Support for virtual LPIs is the GITS_TYPER.Virtual
field.) We also use this define as the *value* that we write into an
interrupt translation table entry's INTTYPE field, which should be 1
for a physical interrupt and 0 for a virtual interrupt. Finally, we
use it as a *mask* when we read the interrupt translation table entry
INTTYPE field.
Untangle this confusion: define an ITE_INTTYPE_VIRTUAL and
ITE_INTTYPE_PHYSICAL to be the valid values of the ITE INTTYPE
field, and replace the ad-hoc collection of ITE_ENTRY_* defines with
use of the FIELD() macro to define the fields of an ITE and the
FIELD_EX64() and FIELD_DP64() macros to read and write them.
We use ITE in the new setup, rather than ITE_ENTRY, because
ITE stands for "Interrupt translation entry" and so the extra
"entry" would be redundant.
We take the opportunity to correct the name of the field that holds
the GICv4 'doorbell' interrupt ID (this is always the value 1023 in a
GICv3, which is why we were calling it the 'spurious' field).
The GITS_TYPE_PHYSICAL define is then used in only one place, where
we set the initial GITS_TYPER value. Since GITS_TYPER.Physical is
essentially a boolean, hiding the '1' value behind a macro is more
confusing than helpful, so expand out the macro there and remove the
define entirely.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
We set the TableDesc entry_sz field from the appropriate
GITS_BASER.ENTRYSIZE field. That ID register field specifies the
number of bytes per table entry minus one. However when we use
td->entry_sz we assume it to be the number of bytes per table entry
(for instance we calculate the number of entries in a page by
dividing the page size by the entry size).
The effects of this bug are:
* we miscalculate the maximum number of entries in the table,
so our checks on guest index values are wrong (too lax)
* when looking up an entry in the second level of an indirect
table, we calculate an incorrect index into the L2 table.
Because we make the same incorrect calculation on both
reads and writes of the L2 table, the guest won't notice
unless it's unlucky enough to use an index value that
causes us to index off the end of the L2 table page and
cause guest memory corruption in whatever follows
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The extract_table_params() decodes the fields in the GITS_BASER<n>
registers into TableDesc structs. Since the fields are the same for
all the GITS_BASER<n> registers, there is currently a lot of code
duplication within the switch (type) statement. Refactor so that the
cases include only what is genuinely different for each type:
the calculation of the number of bits in the ID value that indexes
into the table.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
In extract_table_params() we process each GITS_BASER<n> register. If
the register's Valid bit is not set, this means there is no
in-guest-memory table and so we should not try to interpret the other
fields in the register. This was incorrectly coded as a 'return'
rather than a 'break', so instead of looping round to process the
next GITS_BASER<n> we would stop entirely, treating any later tables
as being not valid also.
This has no real guest-visible effects because (since we don't have
GITS_TYPER.HCC != 0) the guest must in any case set up all the
GITS_BASER<n> to point to valid tables, so this only happens in an
odd misbehaving-guest corner case.
Fix the check to 'break', so that we leave the case statement and
loop back around to the next GITS_BASER<n>.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The TableDesc struct defines properties of the in-guest-memory tables
which the guest tells us about by writing to the GITS_BASER<n>
registers. This struct currently has a union 'maxids', but all the
fields of the union have the same type (uint32_t) and do the same
thing (record one-greater-than the maximum ID value that can be used
as an index into the table).
We're about to add another table type (the GICv4 vPE table); rather
than adding another specifically-named union field for that table
type with the same type as the other union fields, remove the union
entirely and just have a 'uint32_t max_ids' struct field.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
We currently define a bitmask for the GITS_CTLR ENABLED bit in
two ways: as ITS_CTLR_ENABLED, and via the FIELD() macro as
R_GITS_CTLR_ENABLED_MASK. Consistently use the FIELD macro version
everywhere and remove the redundant ITS_CTLR_ENABLED define.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The checks in the ITS on the rdbase values in guest commands are
off-by-one: they permit the guest to pass us a value equal to
s->gicv3->num_cpu, but the valid values are 0...num_cpu-1. This
meant the guest could cause us to index off the end of the
s->gicv3->cpu[] array when calling gicv3_redist_process_lpi(), and we
would probably crash.
(This is not a security bug, because this code is only usable
with emulation, not with KVM.)
Cc: qemu-stable@nongnu.org
Fixes: 17fb5e36aa ("hw/intc: GICv3 redistributor ITS processing")
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
AST2600 Display Port MCU introduces 0x18000000~0x1803FFFF as it's memory
and io address. If guest machine try to access DPMCU memory, it will
cause a fatal error.
Signed-off-by: Troy Lee <troy_lee@aspeedtech.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20211210083034.726610-1-troy_lee@aspeedtech.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Turn on pre-defined feature VIRTIO_BLK_F_SIZE_MAX for virtio blk device to
avoid guest DMA request sizes which are too large for hardware spec.
Signed-off-by: Andy Pei <andy.pei@intel.com>
Message-Id: <1641202092-149677-1-git-send-email-andy.pei@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
The i440fx and Q35 machine types are both hardcoded to use the
legacy SMBIOS 2.1 (32-bit) entry point. This is a sensible
conservative choice because SeaBIOS only supports SMBIOS 2.1
EDK2, however, can also support SMBIOS 3.0 (64-bit) entry points,
and QEMU already uses this on the ARM virt machine type.
This adds a property to allow the choice of SMBIOS entry point
versions For example to opt in to 64-bit SMBIOS entry point:
$QEMU -machine q35,smbios-entry-point-type=64
Based on a patch submitted by Daniel Berrangé.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20211026151100.1691925-4-ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Rename the enums to match the naming style used by QAPI, and to
use "32" and "64" instead of "20" and "31". This will allow us
to more easily move the enum to the QAPI schema later.
About the naming choice: "SMBIOS 2.1 entry point"/"SMBIOS 3.0
entry point" and "32-bit entry point"/"64-bit entry point" are
synonymous in the SMBIOS specification. However, the phrases
"32-bit entry point" and "64-bit entry point" are used more often.
The new names also avoid confusion between the entry point format
and the actual SMBIOS version reported in the entry point
structure. For example: currently the 32-bit entry point
actually report SMBIOS 2.8 support, not 2.1.
Based on portions of a patch submitted by Daniel P. Berrangé.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20211026151100.1691925-2-ehabkost@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Skip triggering an LSI when the AER root error status is updated if no
LSI is defined for the device. We can have a root bridge with no LSI,
MSI and MSI-X defined, for example on POWER systems.
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Message-Id: <20211116170133.724751-4-fbarrat@linux.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Move the pci_intx() definition to the PCI header file, so that it can
be called from other PCI files. It is used by the next patch.
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Message-Id: <20211116170133.724751-3-fbarrat@linux.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Fix the only callsite that doesn't propagate the error code from the
generic vhost code.
Signed-off-by: Roman Kagan <rvkagan@yandex-team.ru>
Message-Id: <20211111153354.18807-11-rvkagan@yandex-team.ru>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
The generic vhost code expects that many of the VhostOps methods in the
respective backends set errno on errors. However, none of the existing
backends actually bothers to do so. In a number of those methods errno
from the failed call is clobbered by successful later calls to some
library functions; on a few code paths the generic vhost code then
negates and returns that errno, thus making failures look as successes
to the caller.
As a result, in certain scenarios (e.g. live migration) the device
doesn't notice the first failure and goes on through its state
transitions as if everything is ok, instead of taking recovery actions
(break and reestablish the vhost-user connection, cancel migration, etc)
before it's too late.
To fix this, consolidate on the convention to return negated errno on
failures throughout generic vhost, and use it for error propagation.
Signed-off-by: Roman Kagan <rvkagan@yandex-team.ru>
Message-Id: <20211111153354.18807-10-rvkagan@yandex-team.ru>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
VhostOps methods in user_ops are not very consistent in their error
returns: some return negated errno while others just -1.
Make sure all of them consistently return negated errno. This also
helps error propagation from the functions being called inside.
Besides, this synchronizes the error return convention with the other
two vhost backends, kernel and vdpa, and will therefore allow for
consistent error propagation in the generic vhost code (in a followup
patch).
Signed-off-by: Roman Kagan <rvkagan@yandex-team.ru>
Message-Id: <20211111153354.18807-9-rvkagan@yandex-team.ru>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Almost all VhostOps methods in vdpa_ops follow the convention of
returning negated errno on error.
Adjust the few that don't. To that end, rework vhost_vdpa_add_status to
check if setting of the requested status bits has succeeded and return
the respective error code it hasn't, and propagate the error codes
wherever it's appropriate.
Signed-off-by: Roman Kagan <rvkagan@yandex-team.ru>
Message-Id: <20211111153354.18807-8-rvkagan@yandex-team.ru>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Almost all VhostOps methods in kernel_ops follow the convention of
returning negated errno on error.
Adjust the only one that doesn't.
Signed-off-by: Roman Kagan <rvkagan@yandex-team.ru>
Message-Id: <20211111153354.18807-7-rvkagan@yandex-team.ru>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Fix the (hypothetical) potential problem when the value parsed out of
the vhost module parameter in sysfs overflows the return value from
vhost_kernel_memslots_limit.
Signed-off-by: Roman Kagan <rvkagan@yandex-team.ru>
Message-Id: <20211111153354.18807-6-rvkagan@yandex-team.ru>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
vhost-user-blk realize only attempts to reconnect if the previous
connection attempt failed on "a problem with the connection and not an
error related to the content (which would fail again the same way in the
next attempt)".
However this distinction is very subtle, and may be inadvertently broken
if the code changes somewhere deep down the stack and a new error gets
propagated up to here.
OTOH now that the number of reconnection attempts is limited it seems
harmless to try reconnecting on any error.
So relax the condition of whether to retry connecting to check for any
error.
This patch amends a527e312b5 "vhost-user-blk: Implement reconnection
during realize".
Signed-off-by: Roman Kagan <rvkagan@yandex-team.ru>
Message-Id: <20211111153354.18807-2-rvkagan@yandex-team.ru>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Unify format used by trace_pci_update_mappings_del(),
trace_pci_update_mappings_add(), trace_pci_cfg_write() and
trace_pci_cfg_read() to print the device name and bus number,
slot number and function number.
For instance:
pci_cfg_read virtio-net-pci 00:0 @0x20 -> 0xffffc00c
pci_cfg_write virtio-net-pci 00:0 @0x20 <- 0xfea0000c
pci_update_mappings_del d=0x555810b92330 01:00.0 4,0xffffc000+0x4000
pci_update_mappings_add d=0x555810b92330 01:00.0 4,0xfea00000+0x4000
becomes
pci_cfg_read virtio-net-pci 01:00.0 @0x20 -> 0xffffc00c
pci_cfg_write virtio-net-pci 01:00.0 @0x20 <- 0xfea0000c
pci_update_mappings_del virtio-net-pci 01:00.0 4,0xffffc000+0x4000
pci_update_mappings_add virtio-net-pci 01:00.0 4,0xfea00000+0x4000
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Message-Id: <20211105192541.655831-1-lvivier@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Yanan Wang <wangyanan55@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add support for configure interrupt, The process is used kvm_irqfd_assign
to set the gsi to kernel. When the configure notifier was signal by
host, qemu will inject a msix interrupt to guest
Signed-off-by: Cindy Lu <lulu@redhat.com>
Message-Id: <20211104164827.21911-11-lulu@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add configure interrupt support for virtio-mmio bus. This
interrupt will be working while the backend is vhost-vdpa
Signed-off-by: Cindy Lu <lulu@redhat.com>
Message-Id: <20211104164827.21911-10-lulu@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add functions to support configure interrupt in virtio_net
The functions are config_pending and config_mask, while
this input idx is VIRTIO_CONFIG_IRQ_IDX will check the
function of configure interrupt.
Signed-off-by: Cindy Lu <lulu@redhat.com>
Message-Id: <20211104164827.21911-9-lulu@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add functions to support configure interrupt.
The configure interrupt process will start in vhost_dev_start
and stop in vhost_dev_stop.
Also add the functions to support vhost_config_pending and
vhost_config_mask, for masked_config_notifier, we only
use the notifier saved in vq 0.
Signed-off-by: Cindy Lu <lulu@redhat.com>
Message-Id: <20211104164827.21911-8-lulu@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add the functions to support the configure interrupt in virtio
The function virtio_config_guest_notifier_read will notify the
guest if there is an configure interrupt.
The function virtio_config_set_guest_notifier_fd_handler is
to set the fd hander for the notifier
Signed-off-by: Cindy Lu <lulu@redhat.com>
Message-Id: <20211104164827.21911-7-lulu@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add new call back function in vhost-vdpa, this function will
set the event fd to kernel. This function will be called
in the vhost_dev_start and vhost_dev_stop
Signed-off-by: Cindy Lu <lulu@redhat.com>
Message-Id: <20211104164827.21911-6-lulu@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
To reuse the interrupt process in configure interrupt
Need to decouple the single vector from the interrupt process. Add new function
kvm_virtio_pci_vector_use_one and _release_one. These functions are use
for the single vector, the whole process will finish in a loop for the vq number.
Signed-off-by: Cindy Lu <lulu@redhat.com>
Message-Id: <20211104164827.21911-4-lulu@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
To reuse the notifier process in configure interrupt.
Use the virtio_pci_get_notifier function to get the notifier.
the INPUT of this function is the IDX, the OUTPUT is notifier and
the vector
Signed-off-by: Cindy Lu <lulu@redhat.com>
Message-Id: <20211104164827.21911-3-lulu@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
To support configure interrupt for vhost-vdpa
Introduce VIRTIO_CONFIG_IRQ_IDX -1 as configure interrupt's queue index,
Then we can reuse the functions guest_notifier_mask and guest_notifier_pending.
Add the check of queue index in these drivers, if the driver does not support
configure interrupt, the function will just return
Signed-off-by: Cindy Lu <lulu@redhat.com>
Message-Id: <20211104164827.21911-2-lulu@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When bus is looked up on a pci write, we didn't
validate that the lookup succeeded.
Fuzzers thus can trigger QEMU crash by dereferencing the NULL
bus pointer.
Fixes: b32bd763a1 ("pci: introduce acpi-index property for PCI device")
Fixes: CVE-2021-4158
Cc: "Igor Mammedov" <imammedo@redhat.com>
Fixes: https://gitlab.com/qemu-project/qemu/-/issues/770
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Ani Sinha <ani@anisinha.ca>
If we warn about the block size being smaller than the default, we skip
some alignment checks.
This can currently only fail on x86-64, when specifying a block size of
1 MiB, however, we detect the THP size of 2 MiB.
Fixes: 228957fea3 ("virtio-mem: Probe THP size to determine default block size")
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20211011173305.13778-1-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add 7.0 machine types for arm/i440fx/q35/s390x/spapr.
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20211217143948.289995-1-cohuck@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
In SPI-mode, SD card's OCR register: Card Capacity Status (CCS) bit
is not set to 1 correclty when the assigned SD image size is larger
than 2GB (SDHC). This will cause the SD card to be indentified as SDSC
incorrectly. CCS bit should be set to 1 if we are using SDHC.
Also, as there's no power up emulation in SPI-mode.
The OCR register: Card power up status bit bit (busy) should also
be set to 1 when reset. (busy bit is set to LOW if the card has not
finished the power up routine.)
Signed-off-by: Frank Chang <frank.chang@sifive.com>
Reviewed-by: Jim Shu <jim.shu@sifive.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20211228125719.14712-1-frank.chang@sifive.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
'wp_groups' holds a bitmap, rename it as 'wp_group_bmap'.
'wpgrps_size' is the bitmap size (in bits), rename it as
'wp_group_bits'.
Patch created mechanically using:
$ sed -i -e s/wp_groups/wp_group_bmap/ \
-e s/wpgrps_size/wp_group_bits/ hw/sd/sd.c
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210728181728.2012952-4-f4bug@amsat.org>
Reviewed-by: Alexander Bulekov <alxndr@bu.edu>
Timers are already initialized in ppc4xx_init(). No need to do it a
second time with a wrong set.
Fixes: d715ea9612 ("PPC: 405: Fix ppc405ep initialization")
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20211222064025.1541490-7-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220103063441.3424853-8-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This is a small cleanup to ease reading. It includes the removal of a
check done on the returned value of g_malloc0(), which can not fail.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20211222064025.1541490-6-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220103063441.3424853-7-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The 405 timers were broken when booke support was added. Assumption
was made that the register numbers were the same but it's not :
SPR_BOOKE_TSR (0x150)
SPR_BOOKE_TCR (0x154)
SPR_40x_TSR (0x3D8)
SPR_40x_TCR (0x3DA)
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Fixes: ddd1055b07 ("PPC: booke timers")
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20211222064025.1541490-5-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220103063441.3424853-6-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Use a QEMU log primitive for errors and trace events for debug.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.drobear.id.au>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20211222064025.1541490-3-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220103063441.3424853-4-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This change has the same motivation as the one done for pnv-phb3-root-bus
buses previously. Defaulting every bus to 'root-bus' makes it impossible to attach
root ports to specific buses and it doesn't allow for custom bus
naming because we're ignoring the 'id' value when registering the root
bus.
After this patch, creating pnv-phb4 devices with 'id' being set will
result in the following qtree:
qemu-system-ppc64 -m 4G -machine powernv9,accel=tcg \
-device pnv-phb4,chip-id=0,index=0,id=pcie.0 \
-device pnv-phb4,chip-id=1,index=4,id=pcie.1
bus: main-system-bus
type System
dev: pnv-phb4, id "pcie.1"
index = 4 (0x4)
chip-id = 1 (0x1)
version = 704374636546 (0xa400000002)
device-id = 1217 (0x4c1)
x-config-reg-migration-enabled = true
bypass-iommu = false
bus: pcie.1
type pnv-phb4-root-bus
dev: pnv-phb4, id "pcie.0"
index = 0 (0x0)
chip-id = 0 (0x0)
version = 704374636546 (0xa400000002)
device-id = 1217 (0x4c1)
x-config-reg-migration-enabled = true
bypass-iommu = false
bus: pcie.0
type pnv-phb4-root-bus
And without setting any ids:
qemu-system-ppc64 -m 4G -machine powernv9,accel=tcg \
-device pnv-phb4,chip-id=0,index=0,id=pcie.0 \
-device pnv-phb4,chip-id=1,index=4,id=pcie.1
bus: main-system-bus
type System
dev: pnv-phb4, id ""
index = 4 (0x4)
chip-id = 1 (0x1)
version = 704374636546 (0xa400000002)
device-id = 1217 (0x4c1)
x-config-reg-migration-enabled = true
bypass-iommu = false
bus: pnv-phb4-root-bus.1
type pnv-phb4-root-bus
dev: pnv-phb4, id ""
index = 0 (0x0)
chip-id = 0 (0x0)
version = 704374636546 (0xa400000002)
device-id = 1217 (0x4c1)
x-config-reg-migration-enabled = true
bypass-iommu = false
bus: pnv-phb4-root-bus.0
type pnv-phb4-root-bus
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20211228193806.1198496-17-danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
All pnv-phb3-root-bus buses are being created as 'root-bus'. This
makes it impossible to, for example, add a pnv-phb3-root-port in
a specific root bus, since they all have the same name. By default
the device will be parented by the pnv-phb3 device that precedeced it in
the QEMU command line.
Moreover, this doesn't all for custom bus naming. Libvirt, for instance,
likes to name these buses as 'pcie.N', where 'N' is the index value of
the controller in the domain XML, by using the 'id' command line
attribute. At this moment this is also being ignored - the created root
bus will always be named 'root-bus'.
This patch fixes both scenarios by removing the 'root-bus' name from the
pci_register_root_bus() call. If an "id" is provided, use that.
Otherwise use 'NULL' as bus name. The 'NULL' value will be handled in
qbus_init_internal() and it will defaulted as lowercase bus type + the
global bus_id value.
After this path we can define the bus name by using the 'id' attribute:
qemu-system-ppc64 -m 4G -machine powernv8,accel=tcg \
-device pnv-phb3,chip-id=0,index=1,id=pcie.0
dev: pnv-phb3, id "pcie.0"
index = 1 (0x1)
chip-id = 0 (0x0)
x-config-reg-migration-enabled = true
bypass-iommu = false
bus: pcie.0
type pnv-phb3-root-bus
And without an 'id' we will have the following default:
qemu-system-ppc64 -m 4G -machine powernv8,accel=tcg \
-device pnv-phb3,chip-id=0,index=1
dev: pnv-phb3, id ""
index = 1 (0x1)
chip-id = 0 (0x0)
x-config-reg-migration-enabled = true
bypass-iommu = false
bus: pnv-phb3-root-bus.0
type pnv-phb3-root-bus
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20211228193806.1198496-3-danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The PHB4 reset handler was preparing ground for PHB5 to set
appropriately the device id. We don't need it for the PHB4 since the
device id is already set in the root port complex. PH5 will introduce
its own.
"device-id" property is now useless. It should be removed.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20211222063817.1541058-3-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The POWER8 processors with a NVLink logic unit have 4 PHB3 devices per
chip.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20211222063817.1541058-2-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The new Cluster-Aware Scheduling support has landed in Linux 5.16,
which has been proved to benefit the scheduling performance (e.g.
load balance and wake_affine strategy) on both x86_64 and AArch64.
So now in Linux 5.16 we have four-level arch-neutral CPU topology
definition like below and a new scheduler level for clusters.
struct cpu_topology {
int thread_id;
int core_id;
int cluster_id;
int package_id;
int llc_id;
cpumask_t thread_sibling;
cpumask_t core_sibling;
cpumask_t cluster_sibling;
cpumask_t llc_sibling;
}
A cluster generally means a group of CPU cores which share L2 cache
or other mid-level resources, and it is the shared resources that
is used to improve scheduler's behavior. From the point of view of
the size range, it's between CPU die and CPU core. For example, on
some ARM64 Kunpeng servers, we have 6 clusters in each NUMA node,
and 4 CPU cores in each cluster. The 4 CPU cores share a separate
L2 cache and a L3 cache tag, which brings cache affinity advantage.
In virtualization, on the Hosts which have pClusters (physical
clusters), if we can design a vCPU topology with cluster level for
guest kernel and have a dedicated vCPU pinning. A Cluster-Aware
Guest kernel can also make use of the cache affinity of CPU clusters
to gain similar scheduling performance.
This patch adds infrastructure for CPU cluster level topology
configuration and parsing, so that the user can specify cluster
parameter if their machines support it.
Signed-off-by: Yanan Wang <wangyanan55@huawei.com>
Message-Id: <20211228092221.21068-3-wangyanan55@huawei.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[PMD: Added '(since 7.0)' to @clusters in qapi/machine.json]
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
All methods related to MachineState are prefixed with "machine_".
smp_parse() does not need to be an exception. Rename it and
const'ify the SMPConfiguration argument, since it doesn't need
to be modified.
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Yanan Wang <wangyanan55@huawei.com>
Tested-by: Yanan Wang <wangyanan55@huawei.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20211216132015.815493-9-philmd@redhat.com>
@pin is an input where we connect a device output.
Rename it @input_pin to simplify the documentation.
Reviewed-by: Yanan Wang <wangyanan55@huawei.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20211218130437.1516929-5-f4bug@amsat.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
ld*_dma() returns a MemTxResult type. Do not discard
it, return it to the caller.
Update the few callers.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20211223115554.3155328-24-philmd@redhat.com>
Let devices specify transaction attributes when calling ld*_pci_dma().
Keep the default MEMTXATTRS_UNSPECIFIED in the few callers.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20211223115554.3155328-22-philmd@redhat.com>
Let devices specify transaction attributes when calling st*_pci_dma().
Keep the default MEMTXATTRS_UNSPECIFIED in the few callers.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20211223115554.3155328-21-philmd@redhat.com>
dma_memory_read() returns a MemTxResult type. Do not discard
it, return it to the caller.
Update the few callers.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20211223115554.3155328-19-philmd@redhat.com>
Let devices specify transaction attributes when calling ld*_dma().
Keep the default MEMTXATTRS_UNSPECIFIED in the few callers.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20211223115554.3155328-17-philmd@redhat.com>
Let devices specify transaction attributes when calling st*_dma().
Keep the default MEMTXATTRS_UNSPECIFIED in the few callers.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20211223115554.3155328-16-philmd@redhat.com>
Let devices specify transaction attributes when calling
dma_buf_read().
Keep the default MEMTXATTRS_UNSPECIFIED in the few callers.
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20211223115554.3155328-13-philmd@redhat.com>
Let devices specify transaction attributes when calling
dma_buf_write().
Keep the default MEMTXATTRS_UNSPECIFIED in the few callers.
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20211223115554.3155328-12-philmd@redhat.com>
Let devices specify transaction attributes when calling pci_dma_rw().
Keep the default MEMTXATTRS_UNSPECIFIED in the few callers.
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20211223115554.3155328-10-philmd@redhat.com>
DMA operations are run on any kind of buffer, not arrays of
uint8_t. Convert dma_buf_read/dma_buf_write functions to take
a void pointer argument and save us pointless casts to uint8_t *.
Remove this pointless casts in the megasas device model.
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20211223115554.3155328-9-philmd@redhat.com>
Let devices specify transaction attributes when calling
dma_memory_map().
Patch created mechanically using spatch with this script:
@@
expression E1, E2, E3, E4;
@@
- dma_memory_map(E1, E2, E3, E4)
+ dma_memory_map(E1, E2, E3, E4, MEMTXATTRS_UNSPECIFIED)
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20211223115554.3155328-7-philmd@redhat.com>
Let devices specify transaction attributes when calling
dma_memory_rw().
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20211223115554.3155328-5-philmd@redhat.com>
Let devices specify transaction attributes when calling
dma_memory_set().
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20211223115554.3155328-3-philmd@redhat.com>
While the reply queue values fit in 16-bit, they are accessed
as 32-bit:
661: s->reply_queue_head = ldl_le_pci_dma(pcid, s->producer_pa);
662: s->reply_queue_head %= MEGASAS_MAX_FRAMES;
663: s->reply_queue_tail = ldl_le_pci_dma(pcid, s->consumer_pa);
664: s->reply_queue_tail %= MEGASAS_MAX_FRAMES;
Having:
41:#define MEGASAS_MAX_FRAMES 2048 /* Firmware limit at 65535 */
In order to update the ld/st*_pci_dma() API to pass the address
of the value to access, it is simpler to have the head/tail declared
as 32-bit values. Replace the uint16_t by uint32_t, wasting 4 bytes in
the MegasasState structure.
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20211223115554.3155328-20-philmd@redhat.com>
virtio-net-failover test tries several device combinations that produces
some expected warnings.
These warning can be confusing, so we disable them during the qtest
sequence.
Reported-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Message-Id: <20211220145314.390697-1-lvivier@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
[thuth: Fix memory leak by using error_free()]
Signed-off-by: Thomas Huth <thuth@redhat.com>
GraphicHw.gl_flushed was introduced to notify the
device (vhost-user-gpu) that the GL resources (the display scanout) are
no longer needed.
It was decoupled from QEMU own gl-blocking mechanism, but that
difference isn't helping. Instead, we can reuse QEMU gl-blocking and
notify virtio_gpu_gl_flushed() when unblocking (to unlock
vhost-user-gpu).
An extra block/unblock is added arount dpy_gl_update() so existing
backends that don't block will have the flush event handled. It will
also help when there are no backends associated.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
It's part of Linux headers for a while now.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Currently, virgl initialization error is silent. Make it verbose instead.
(this is likely going to bug later on, as the device isn't fully
initialized)
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
The original BBL boot method had the kernel embedded as an opaque blob
that was blindly jumped to, which OpenSBI implemented as fw_payload.
OpenSBI then implemented fw_jump, which allows the payload to be loaded
elsewhere, but still blindly jumps to a fixed address at which the
kernel is to be loaded. Finally, OpenSBI introduced fw_dynamic, which
allows the previous stage to inform it where to jump to, rather than
having to blindly guess like fw_jump, or embed the payload as part of
the build like fw_payload. When used with an opaque binary (i.e. the
output of objcopy -O binary), it matches the behaviour of the previous
methods. However, when used with an ELF, QEMU currently passes on the
ELF's entry point address, which causes a discrepancy compared with all
the other boot methods if that entry point is not the first instruction
in the binary.
This difference specific to fw_dynamic with an ELF is not apparent when
booting Linux, since its entry point is the first instruction in the
binary. However, FreeBSD has a separate ELF entry point, following the
calling convention used by its bootloader, that differs from the first
instruction in the binary, used for the legacy SBI entry point, and so
the specific combination of QEMU's default fw_dynamic firmware with
booting FreeBSD as an ELF rather than a raw binary does not work.
Thus, align the behaviour when loading an ELF with the behaviour when
loading a raw binary; namely, use the base address of the loaded kernel
in place of the entry point.
The uImage code is left as-is in using the U-Boot header's entry point,
since the calling convention for that entry point is the same as the SBI
one and it mirrors what U-Boot will do.
Signed-off-by: Jessica Clarke <jrtc27@jrtc27.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20211214032456.70203-1-jrtc27@jrtc27.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
If the 'i8042' property is not set, mouse events handled by
vmmouse_mouse_event() end calling i8042_isa_mouse_fake_event()
with a NULL argument, resulting in ps2_mouse_fake_event() being
called with invalid PS2MouseState pointer. Fix by requiring
the 'i8042' property to be always set:
$ qemu-system-x86_64 -device vmmouse
qemu-system-x86_64: -device vmmouse: 'i8042' link is not set
Fixes: 91c9e09147 ("vmmouse: convert to qdev")
Reported-by: Calvin Buckley <calvin@cmpct.info>
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/752
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20211201223253.36080-1-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If we detect an overflow on the SGL buffer, do not
keep processing the command: discard it. TARGET_FAILURE
sense code will be returned (MFI_STAT_SCSI_DONE_WITH_ERROR).
Reported-by: Alexander Bulekov <alxndr@bu.edu>
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/521
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Darren Kenny <darren.kenny@oracle.com>
Message-Id: <20211119201141.532377-2-philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
* General cleanup for Mac machines (Peter)
* Fixes for FPU exceptions (Lucas)
* Support for new ISA31 instructions (Matheus)
* Fixes for ivshmem (Daniel)
* Cleanups for PowerNV PHB (Christophe and Cedric)
* Updates of PowerNV and pSeries documentation (Leonardo and Daniel)
* Fixes for PowerNV (Daniel)
* Large cleanup of FPU implementation (Richard)
* Removal of SoftTLBs support for PPC74x CPUs (Fabiano)
* Fixes for exception models in MPCx and 60x CPUs (Fabiano)
* Removal of 401/403 CPUs (Cedric)
* Deprecation of taihu machine (Thomas)
* Large rework of PPC405 machine (Cedric)
* Fixes for VSX instructions (Victor and Matheus)
* Fix for e6500 CPU (Fabiano)
* Initial support for PMU (Daniel)
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEoPZlSPBIlev+awtgUaNDx8/77KEFAmG8xt8ACgkQUaNDx8/7
7KG3Dg/9EXK3GslNgUNRvB1pgRSimnrUirGUiDmZPXxevIbsoPsYaXmUcD1zOnlb
zXiCzQ2Bvi8ZUjT1uScP7dkFCdzs6gXYbTEcTzscX3k2VnTjXHXhQ3cnb0uModP5
U1QzrjV7K/q1usJW5OVSGZS1PoWOqWuZNdcp0mIUWcJHhSaYtUGGPohp7rH0JSug
ncmkRA0KLgIX8eg8swyfJxrw9wCcXlFIcmwHipB8S/Dd/gUpmFEoaQsmugSJNYZe
zi8Fd4jfzlRXVwb8EUSiOiaXSd/WKjEcQx/usbzzaBacbktk/nfy+rligUMryCpO
vGFM5blxEX5SXD3Cd0vcFwYhCZImphD8K+Sxe6Us69rsUH11hJS+q29/Puk1MkHt
DTubqB3k4BheiatOV1zeUMlbRm5svUhGj3VstFZYZeZ3Oh47Jsx3XH4hoytUuc/1
lP9UGkaf3nIx12vSqBA/3Crc7zalWX5OhaUV5RG30+jxd8zHOKcasKbd22710DNz
4WybQLb3bpUr091mWMKcaAkP6bxcE8S+mR4LE2kdELboAnkB+OgSmrdZ3slceaCv
btV8qjNl4f8lBvyFQVxZ5bn05+TfxUXFlFxXipxf1fI64bYwRnyQQ3yRxMHipRYK
CRta1akVgIgcBbeeRHBZLA12UgTQJY6WIoDaZMz9NxIDHJnX/jw=
=APFd
-----END PGP SIGNATURE-----
Merge tag 'pull-ppc-20211217' of https://github.com/legoater/qemu into staging
ppc 7.0 queue:
* General cleanup for Mac machines (Peter)
* Fixes for FPU exceptions (Lucas)
* Support for new ISA31 instructions (Matheus)
* Fixes for ivshmem (Daniel)
* Cleanups for PowerNV PHB (Christophe and Cedric)
* Updates of PowerNV and pSeries documentation (Leonardo and Daniel)
* Fixes for PowerNV (Daniel)
* Large cleanup of FPU implementation (Richard)
* Removal of SoftTLBs support for PPC74x CPUs (Fabiano)
* Fixes for exception models in MPCx and 60x CPUs (Fabiano)
* Removal of 401/403 CPUs (Cedric)
* Deprecation of taihu machine (Thomas)
* Large rework of PPC405 machine (Cedric)
* Fixes for VSX instructions (Victor and Matheus)
* Fix for e6500 CPU (Fabiano)
* Initial support for PMU (Daniel)
# gpg: Signature made Fri 17 Dec 2021 09:20:31 AM PST
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@kaod.org>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* tag 'pull-ppc-20211217' of https://github.com/legoater/qemu: (101 commits)
ppc/pnv: Use QOM hierarchy to scan PEC PHB4 devices
ppc/pnv: Move realize of PEC stacks under the PEC model
ppc/pnv: Remove "system-memory" property from PHB4 PEC
ppc/pnv: Compute the PHB index from the PHB4 PEC model
ppc/pnv: Introduce a num_stack class attribute
ppc/pnv: Introduce a "chip" property under the PHB4 model
ppc/pnv: Introduce version and device_id class atributes for PHB4 devices
ppc/pnv: Introduce a num_pecs class attribute for PHB4 PEC devices
ppc/pnv: Use QOM hierarchy to scan PHB3 devices
ppc/pnv: Move mapping of the PHB3 CQ regions under pnv_pbcq_realize()
ppc/pnv: Drop the "num-phbs" property
ppc/pnv: Use the chip class to check the index of PHB3 devices
ppc/pnv: Introduce a "chip" property under PHB3
PPC64/TCG: Implement 'rfebb' instruction
target/ppc/power8-pmu.c: add PM_RUN_INST_CMPL (0xFA) event
target/ppc: enable PMU instruction count
target/ppc: enable PMU counter overflow with cycle events
target/ppc: PMU: update counters on MMCR1 write
target/ppc: PMU: update counters on PMCs r/w
target/ppc: PMU basic cycle count for pseries TCG
...
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
When -nodefaults is supported for PHB4 devices, the pecs array under
the chip will be empty. This will break the 'info pic' HMP command.
Do a QOM loop on the chip children and look for PEC PHB4 devices
instead.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20211213132830.108372-15-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This change will help us providing support for user created PHB4
devices.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20211213132830.108372-14-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This is not useful and will be in the way for support of user created
PHB4 devices.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20211213132830.108372-13-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Use the num_stacks class attribute to compute the PHB index depending
on the PEC index :
* PEC0 provides 1 PHB (PHB0)
* PEC1 provides 2 PHBs (PHB1 and PHB2)
* PEC2 provides 3 PHBs (PHB3, PHB4 and PHB5)
The routine pnv_pec_phb_offset() is a bit complex but it also prepares
ground for PHB5 which has a different layout of stacks: 3 per PECs.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20211213132830.108372-12-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Each PEC device of the POWER9 chip has a predefined number of stacks,
equivalent of a root port complex:
PEC0 -> 1 stack
PEC1 -> 2 stacks
PEC2 -> 3 stacks
Introduce a class attribute to hold these values and remove the
"num-stacks" property.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20211213132830.108372-11-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
And check the PEC index using the chip class.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20211213132830.108372-10-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
It prepares ground for PHB5 which has different values.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20211213132830.108372-9-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
POWER9 processor comes with 3 PHB4 PEC (PCI Express Controller) and
each PEC can have several PHBs :
* PEC0 provides 1 PHB (PHB0)
* PEC1 provides 2 PHBs (PHB1 and PHB2)
* PEC2 provides 3 PHBs (PHB3, PHB4 and PHB5)
A num_pecs class attribute represents better the logic units of the
POWER9 chip. Use that instead of num_phbs which fits POWER8 chips.
This will ease adding support for user created devices.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20211213132830.108372-8-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
When -nodefaults is supported for PHB3 devices, the phbs array under
the chip will be empty. This will break the XICSFabric handlers, and
all interrupt delivery, and the 'info pic' HMP command.
Do a QOM loop on the chip children and look for PHB3 devices instead.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20211213132830.108372-7-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This change will help us providing support for user created PHB3
devices.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20211213132830.108372-6-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
It is never used.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20211213132830.108372-5-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The maximum number of PHB3 devices per chip can be different depending
on the POWER8 processor model.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20211213132830.108372-4-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This change will help us move the mapping of XSCOM regions under the
PHB3 realize routine, which will be necessary for user created PHB3
devices.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20211213132830.108372-3-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This patch starts an IBM Power8+ compatible PMU implementation by adding
the representation of PMU events that we are going to sample,
PMUEventType. This enum represents a Perf event that is being sampled by
a specific counter 'sprn'. Events that aren't available (i.e. no event
was set in MMCR1) will be of type 'PMU_EVENT_INVALID'. Events that are
inactive due to frozen counter bits state are of type
'PMU_EVENT_INACTIVE'. Other types added in this patch are
PMU_EVENT_CYCLES and PMU_EVENT_INSTRUCTIONS. More types will be added
later on.
Let's also add the required PMU cycle overflow timers. They will be used
to trigger cycle overflows when cycle events are being sampled. This
timer will call cpu_ppc_pmu_timer_cb(), which in turn calls
fire_PMC_interrupt(). Both functions are stubs that will be implemented
later on when EBB support is added.
Two new helper files are created to host this new logic.
cpu_ppc_pmu_init() will init all overflow timers during CPU init time.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20211201151734.654994-2-danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Adapt the fields offset in the board information for Linux. Since
Linux relies on the CPU frequency value, I wonder how it ever worked.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20211206103712.1866296-15-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The board information for the 405EP first appeared in commit 04f20795ac
("Move PowerPC 405 specific definitions into a separate file ...")
An Ethernet address is a 6 byte number. Fix that.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20211206103712.1866296-14-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
These values are computed and updated by U-Boot at startup. Use them
as defaults to improve direct Linux boot.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20211206103712.1866296-13-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The machine can already boot with kernel and initrd U-boot images if a
firmware is loaded first. Adapt and improve the load sequence to let
the machine boot directly from a Linux kernel ELF image and a usual
initrd image if a firmware image is not provided. For that, install a
custom CPU reset handler to setup the registers and to start the CPU
from the Linux kernel entry point.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20211206103712.1866296-12-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This routine is a small helper to cleanup the code. The update of the
flash fields were removed because there are not of any use when booting
from a Linux kernel image. It should be functionally equivalent.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20211206103712.1866296-11-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
QEMU installs a custom U-Boot in-memory descriptor to share board
information with Linux, which means that the QEMU machine was
initially designed to support booting Linux directly without using the
loaded FW. But, it's not that simple because the CPU still starts at
address 0xfffffffc where nothing is currently mapped. Support must
have been broken these last years.
Since we can not find a "ppc405_rom.bin" firmware file, request one to
be specified on the command line. A consequence of this change is that
the machine can be booted directly from Linux without any FW being
loaded. This is still broken and the CPU start address will be fixed
in the next changes.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20211206103712.1866296-10-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
It is currently impossible to find a "ppc405_rom.bin" firmware file or
a full flash image for the PPC405EP evalution board. Even if it should
be technically possible to recreate such an image, it's unlikely that
anyone will do it since the board is obsolete and support in QEMU has
been broken for about 10 years.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20211206103712.1866296-9-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
I will be useful to rework the boot from Linux.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20211206103712.1866296-7-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
It was introduced in commit b8d3f5d126 ("Add flags to support
PowerPC 405 bootinfos variations.") but since its value has always
been set to '1'.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20211206103712.1866296-6-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
and one error message to a LOG_GUEST_ERROR.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20211206103712.1866296-5-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Peter Maydell
Troy Lee
Andy Pei
Eduardo Habkost
Frederic Barrat
Roman Kagan
Laurent Vivier
Cindy Lu
Michael S. Tsirkin
David Hildenbrand
Cornelia Huck
Frank Chang
Philippe Mathieu-Daudé
Cédric Le Goater
Daniel Henrique Barboza
Yanan Wang
Philippe Mathieu-Daudé
Marc-André Lureau
Jessica Clarke
Richard Henderson