Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <1483952153-7221-3-git-send-email-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
From time to time, there are issues with ioapic, either on guest side or
on hypervisor side. Good to have some persistent traces for better
triaging and debugging.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <1483952153-7221-2-git-send-email-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The GICv3 requires that we only signal Pending interrupts to
the CPU. This category does not include Pending+Active interrupts,
which means we need to check whether the interrupt is Active in
the gicr_int_pending() and gicd_int_pending() functions.
Interrupts are rarely in the Active+Pending state, but KVM
uses this as part of its handling of the virtual timer, so
this bug was causing KVM to go into an infinite loop of
taking the vtimer interrupt when the guest first triggered it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
In the ARMCPRegInfo definitions for the GICv3 CPU interface
registers, we were trying to use .fieldoffset to specify
the locations of data fields within the GICv3CPUState struct.
This is completely broken, because .fieldoffset is for offsets
into the CPUARMState struct. We didn't notice because we
were only using this for reads to BPR0, AP0R<n>, IGRPEN0
and CTLR_EL3, and Linux doesn't use these registers.
Replace the .fieldoffset uses with explicit read functions.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Andrew Jones <drjones@redhat.com>
Message-id: 20161209143703.29457-1-drjones@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We've currently got 18 architectures in QEMU, and thus 18 target-xxx
folders in the root folder of the QEMU source tree. More architectures
(e.g. RISC-V, AVR) are likely to be included soon, too, so the main
folder of the QEMU sources slowly gets quite overcrowded with the
target-xxx folders.
To disburden the main folder a little bit, let's move the target-xxx
folders into a dedicated target/ folder, so that target-xxx/ simply
becomes target/xxx/ instead.
Acked-by: Laurent Vivier <laurent@vivier.eu> [m68k part]
Acked-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de> [tricore part]
Acked-by: Michael Walle <michael@walle.cc> [lm32 part]
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com> [s390x part]
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com> [s390x part]
Acked-by: Eduardo Habkost <ehabkost@redhat.com> [i386 part]
Acked-by: Artyom Tarasenko <atar4qemu@gmail.com> [sparc part]
Acked-by: Richard Henderson <rth@twiddle.net> [alpha part]
Acked-by: Max Filippov <jcmvbkbc@gmail.com> [xtensa part]
Reviewed-by: David Gibson <david@gibson.dropbear.id.au> [ppc part]
Acked-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com> [crisµblaze part]
Acked-by: Guan Xuetao <gxt@mprc.pku.edu.cn> [unicore32 part]
Signed-off-by: Thomas Huth <thuth@redhat.com>
According to ARM DUI 0552A 4.2.10. NVIC set pending status
also for disabled interrupts. Correct the logic for
when interrupts are marked pending both on input level
transition and when interrupts are dismissed, to match
the NVIC behaviour rather than the 11MPCore GIC.
Signed-off-by: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently the device tree node for the XICS interrupt controller is in
spapr_create_fdt_skel(). As part of consolidating device tree construction
to reset time, this moves it to a function called from spapr_build_fdt().
In addition we move the actual code into hw/intc/xics_spapr.c with the
rest of the PAPR specific interrupt controller code.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
The routines :
void icp_set_cppr(ICPState *icp, uint8_t cppr);
void icp_set_mfrr(ICPState *icp, uint8_t mfrr);
void icp_eoi(ICPState *icp, uint32_t xirr);
now use one 'ICPState *icp' argument instead of a 'XICSState *' and a
server arguments. The backlink on XICSState* is used whenever needed.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The link will be used to change the API of the icp_* routines which
are still using an XICSState as an argument.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
xics_spapr and xics_kvm nearly define the same 'set_nr_servers'
handler. Only the type of the ICP differs. So let's make a common one
to remove some duplicated code.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Useful to debug interrupt problems.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[clg: - updated for qemu-2.7
- added a test on ->irqs as it is not necessarily allocated
(PHB3_MSI)
- removed static variable g_xics and replace with a loop on all
children to find the xics objects.
- rebased on InterruptStatsProvider interface ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
SDM: x2APIC State Transitions:
State Changes From xAPIC Mode to x2APIC Mode
"
Any APIC ID value written to the memory-mapped
local APIC ID register is not preserved
"
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
APIC ID should be restored to initial APIC ID
state after Reset and Power-On.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
ACPI ID is 32 bit wide on CPUs with x2APIC support.
Extend 'id' property to support it.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Fix some problems with the tracepoints for ICC register reads
and writes:
* tracepoints for ICC_BPR<n>, ICC_AP<n>R<x>, ICC_IGRPEN<n>,
ICC_EIOR<n> were not printing the <n> that indicated whether
the access was to the group 0 or 1 register
* the ICC_IGREPEN1_EL3 read function was not actually calling
the associated tracepoint
* the ICC_BPR<n> write function was incorrectly calling the
tracepoint for ICC_PMR writes
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1476294876-12340-4-git-send-email-peter.maydell@linaro.org
Remove unused debugging code to fix native building on aarch64. Without
this change, the following -Werr output inhibits make from completing.
qemu/hw/intc/arm_gic_kvm.c:38:18: error: debug_gic_kvm defined but not used [-Werror=unused-const-variable=]
static const int debug_gic_kvm = 0;
^~~~~~~~~~~~~
cc1: all warnings being treated as errors
qemu/rules.mak:60: recipe for target 'hw/intc/arm_gic_kvm.o' failed
make[1]: *** [hw/intc/arm_gic_kvm.o] Error 1
Makefile:205: recipe for target 'subdir-aarch64-softmmu' failed
Signed-off-by: Christopher Covington <cov@codeaurora.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20161011163202.19720-1-cov@codeaurora.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The MMIO based interface to APIC doesn't work well with MSIs that have
upper address bits set (remapped x2APIC MSIs). A specialized interface
is a quick and dirty way to avoid the shortcoming.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Every configuration has only up to one APIC class and we'll be extending
the class with a function that can be called without an instanced
object, so a direct access to the class is convenient.
This patch will break compilation if some code uses apic_get_class()
with CONFIG_USER_ONLY.
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The existing implementation remains same and ics-base is introduced. The
type name "ics" is retained, and all the related functions renamed as
ics_simple_*
This will allow different implementations for the source controllers
such as the MSI support of PHB3 on Power8 which uses in-memory state
tables for example.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
[ clg: added ICS_BASE_GET_CLASS and related fixes, based on :
http://patchwork.ozlabs.org/patch/646010/ ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Instead of an array of fixed sized blocks, use a list, as we will need
to have sources with variable number of interrupts. SPAPR only uses
a single entry. Native will create more. If performance becomes an
issue we can add some hashed lookup but for now this will do fine.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[ move the initialization of list to xics_common_initfn,
restore xirr_owner after migration and move restoring to
icp_post_load]
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
[ clg: removed the icp_post_load() changes from nikunj patchset v3:
http://patchwork.ozlabs.org/patch/646008/ ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The ITS control frame is in-kernel emulated while accesses to the
GITS_TRANSLATER are mediated through the KVM_SIGNAL_MSI ioctl (MSI
direct MSI injection advertised by the CAP_SIGNAL_MSI capability)
the kvm_gsi_direct_mapping is explicitly set to false to emphasize the
difference with GICv2M. Direct mapping cannot work with ITS since
the content of the MSI data is not the target interrupt ID but an
eventd id.
GSI routing is advertised (kvm_gsi_routing_allowed) as well as
msi/irqfd signaling (kvm_msi_via_irqfd_allowed).
The MSI frame (GITS_TRANSLATER) absolute GPA is computed on first
kvm_its_send_msi() call. It is then passed through KVM_SIGNAL_MSI
ioctl.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1474616617-366-6-git-send-email-eric.auger@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is the basic skeleton for both KVM and software-emulated ITS.
Since we already prepare status structure, we also introduce complete
VMState description. But, because we currently have no migratable
implementations, we also set unmigratable flag.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1474616617-366-3-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Advertise gsi routing and set up irqchip routing entries for
GIC SPIs.
This is not mandated as long as MSI routing is not used
(because the kernel sets a default irqchip routing table).
However once MSI routing gets used (for VIRTIO-PCI vhost for
example), the first call to KVM_SET_GSI_ROUTING overrides the
kernel default irqchip table.
If no routing entry exists for the GSI, any IRQFD signaling for
this GSI will fail.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1474616617-366-2-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We have to change the vmstate version due to changes in statistics counters.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Message-Id: <1474921408-24710-5-git-send-email-hpoussin@reactos.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This interface will be used by HMP commands 'info irq' and 'info pic'.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Message-Id: <1474921408-24710-2-git-send-email-hpoussin@reactos.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It's 2.8 now, and maybe it's time to switch IOAPIC default version to
0x20.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <1474608795-23058-1-git-send-email-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Fix inconsistent irq status, because of this in the trace logs, for e.g.
LSI status was 0x7, i.e. XICS_STATUS_ASSERTED, XICS_STATUS_SENT and
XICS_STATUS_REJECTED all set, which did not make sense. So the REJECTED
would have been set in earlier interrupt cycle, and then asserted and
sent in this current one.
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Introduce a new APIC macro to replace APIC_COMMON macro in
hw/intc/apic.c in order to capture access LAPIC in qemu
even if LAPIC is emulated in kvm.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Message-Id: <1473923759-13912-1-git-send-email-wanpeng.li@hotmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We abort a few lines above if kernel_xics_fd == -1.
This is only code cleanup.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Some old Linux kernels (upstream before v4.0), or any released RHEL
kernels has problem in sending APIC EOI when IR is enabled. Meanwhile,
many of them only support explicit EOI for IOAPIC, which is only
introduced in IOAPIC version 0x20. This patch provide a way to boost
QEMU IOAPIC to version 0x20, in order for QEMU to correctly receive EOI
messages.
Without boosting IOAPIC version to 0x20, kernels before commit d32932d
("x86/irq: Convert IOAPIC to use hierarchical irqdomain interfaces")
will have trouble enabling both IR and level-triggered interrupt devices
(like e1000).
To upgrade IOAPIC to version 0x20, we need to specify:
-global ioapic.version=0x20
To be compatible with old systems, 0x11 will still be the default IOAPIC
version. Here 0x11 and 0x20 are the only versions to be supported.
One thing to mention: this patch only applies to emulated IOAPIC. It
does not affect kernel IOAPIC behavior.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <1470059959-372-1-git-send-email-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
For level triggered interrupts, we will get Remote IRR bit cleared after
guest kernel finished processing specific request. Before that, we
should ignore the same interrupt from triggering again.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <1469974685-4144-1-git-send-email-peterx@redhat.com>
[Push new "if" up so that it covers KVM split irqchip as well. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- interrupt remapping for intel iommus
- a bunch of virtio cleanups
- fixes all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXkQsqAAoJECgfDbjSjVRpanoIAJ9JVlc1aEjt9sa0cSBcs+NQ
J7JmgU9FqFsj+4FrNTouO3AxTjHurd1UAULP1WMPD+V3JpbnHct8r6SCBLQ5EBMN
VOjYo4DwWs1g+DqnQ9WZmbadu06XvYi/yiAKNUzWfZk0MR11D0D/S5hmarNKw0Kq
tGHeTWjGeY4WqFLV7m+qB4+cqkAByn6um99UtUvgLL05RgIEIP2IEMKYZ+rXvAa9
iGUvzqlO7mbq/+LbL18kaWywa4TCwbbd2eSGWaqhX4CuB62Rl33mWTXFcfaYhkyp
Z3FgwaJ09h0lAjSVEbyAuLFMfO/BnMcsoKqwl4xc4vkn/xBCqFtgH9JcEVm3O8U=
=ge2D
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pc, pci, virtio: new features, cleanups, fixes
- interrupt remapping for intel iommus
- a bunch of virtio cleanups
- fixes all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Thu 21 Jul 2016 18:49:30 BST
# gpg: using RSA key 0x281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (57 commits)
intel_iommu: avoid unnamed fields
virtio: Update migration docs
virtio-gpu: Wrap in vmstate
virtio-gpu: Use migrate_add_blocker for virgl migration blocking
virtio-input: Wrap in vmstate
9pfs: Wrap in vmstate
virtio-serial: Wrap in vmstate
virtio-net: Wrap in vmstate
virtio-balloon: Wrap in vmstate
virtio-rng: Wrap in vmstate
virtio-blk: Wrap in vmstate
virtio-scsi: Wrap in vmstate
virtio: Migration helper function and macro
virtio-serial: Remove old migration version support
virtio-net: Remove old migration version support
virtio-scsi: Replace HandleOutput typedef
Revert "mirror: Workaround for unexpected iohandler events during completion"
virtio-scsi: Call virtio_add_queue_aio
virtio-blk: Call virtio_add_queue_aio
virtio: Introduce virtio_add_queue_aio
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Let IOAPIC the first consumer of x86 IOMMU IEC invalidation
notifiers. This is only used for split irqchip case, when vIOMMU
receives IR invalidation requests, IOAPIC will be notified to update
kernel irq routes. For simplicity, we just update all IOAPIC routes,
even if the invalidated entries are not IOAPIC ones.
Since now we are creating IOMMUs using "-device" parameter, IOMMU
device will be created after IOAPIC. We need to do the registration
after machine done by leveraging machine_done notifier.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Abstract IOAPIC entry parsing logic into a helper function.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch translates all IOAPIC interrupts into MSI ones. One pseudo
ioapic address space is added to transfer the MSI message. By default,
it will be system memory address space. When IR is enabled, it will be
IOMMU address space.
Currently, only emulated IOAPIC is supported.
Idea suggested by Jan Kiszka and Rita Sinha in the following patch:
https://lists.gnu.org/archive/html/qemu-devel/2016-03/msg01933.html
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
instance_id is generated by last_used_id + 1 for a given device type
so for QEMU with 3 CPUs instance_id for APICs is a seti of [0, 1, 2]
When CPU in the middle is hot-removed and migration started
APICs with instance_ids 0 and 2 are transferred in migration stream.
However target starts with 2 CPUs and APICs' instance_ids are
generated from scratch [0, 1] hence migration fails with error
Unknown savevm section or instance 'apic' 2
Fix issue by manually registering APIC's vmsd with apic_id as
instance_id, in this case instance_id on target will always
match instance_id on source as apic_id is the same for a given
cpu instance.
Reported-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Callbacks will do necessary cleanups before APIC device is deleted
Signed-off-by: Chen Fan <chen.fan.fnst@cn.fujitsu.com>
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Zhu Guihua <zhugh.fnst@cn.fujitsu.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
local_apics[] is sized to contain all APIC ID supported in xAPIC mode,
so use APIC ID as index in it instead of constantly increasing counter idx.
Fixes error "apic initialization failed" when a CPU hotplugged and
unplugged more times than there are free slots in local_apics[].
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
MAX_APICS is only used by child 'apic' class and not
by its parent TYPE_APIC_COMMON or any other derived
class.
Move check into end user 'apic' class so it won't
get in the way of other APIC implementations
if they support more then MAX_APICS.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Coverity complains that the GICR_IPRIORITYR case in gicv3_readl()
can overflow an array, because it doesn't know that the offsets
passed to that function must be word aligned. Add some assert()s
which hopefully tell Coverity that this isn't possible.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1468261372-17508-1-git-send-email-peter.maydell@linaro.org
Changes:
* support 10-bit ASIDs
* MIPS64R6-generic renamed to I6400
* initial GIC support
* implement RESET_BASE register in CM GCR
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJXhMtOAAoJEFIRjjwLKdprahQH/2qBMp7Hnucy7jhiPHRtRZTo
zZAhuRJ0Z2LT9xH+sTg3HcjHI7aXps5cG2f7Fw4X/JKNRY4KO19yEBnMhc5he2Ut
XPtHCeMXXq6zU4RMHqlx6wChHn5AUll/3EeSvm6JMV+HhE6oDBk1yl5C8ipPlVCd
KEz6LlUFNMbuxu2tM4DoMNAWeKmunBx3vO+JuErB6hjCWM5G0mV9aPDkbwTOmVLn
qGgzzmNDiPE6JWrSpbHetsdCO7V9xtXzhcFsu240GJ/+XJMjUXb1m6ETsJxT9EYh
vLfFzwozBSjX6ZQZVNFIAeJZnq96NOHqZ56sU7s4YktVXjl26JAahScTTH0aiNo=
=sTce
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/lalrae/tags/mips-20160712' into staging
MIPS patches 2016-07-12
Changes:
* support 10-bit ASIDs
* MIPS64R6-generic renamed to I6400
* initial GIC support
* implement RESET_BASE register in CM GCR
# gpg: Signature made Tue 12 Jul 2016 11:49:50 BST
# gpg: using RSA key 0x52118E3C0B29DA6B
# gpg: Good signature from "Leon Alrae <leon.alrae@imgtec.com>"
# Primary key fingerprint: 8DD3 2F98 5495 9D66 35D4 4FC0 5211 8E3C 0B29 DA6B
* remotes/lalrae/tags/mips-20160712:
target-mips: enable 10-bit ASIDs in I6400 CPU
target-mips: support CP0.Config4.AE bit
target-mips: change ASID type to hold more than 8 bits
target-mips: add ASID mask field and replace magic values
target-mips: replace MIPS64R6-generic with the real I6400 CPU model
hw/mips_cmgcr: implement RESET_BASE register in CM GCR
hw/mips_cpc: make VP correctly start from the reset vector
target-mips: add exception base to MIPS CPU
hw/mips/cps: create GIC block inside CPS
hw/mips: implement Global Interrupt Controller
hw/mips: implement GIC Interval Timer
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Global Interrupt Controller (GIC) is responsible for mapping each
internal and external interrupt to the correct location for servicing.
The internal representation of registers is different from the specification
in order to consolidate information for each GIC Interrupt Sources and Virtual
Processors with same functionalities. For example SH_MAP00_VP00 registers are
defined like each bit represents a VP but in this implementation the equivalent
map_vp contains VP number in integer form for ease accesses. When it is being
accessed via read write functions an internal data is converted back into the
original format as the specification.
Limitations:
Level triggering only
GIC CounterHi not implemented (Countbits = 32bits)
DINT not implemented
Local WatchDog, Fast Debug Channel, Perf Counter not implemented
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Starting QEMU with -S results in current_cpu containing its initial
value of NULL. It is however possible to connect to such QEMU instance
and query various CPU registers, one example being CPUID, and doing that
results in QEMU segfaulting.
Using qemu_get_cpu(0) seem reasonable enough given that ARMv7M
architecture is a single core architecture.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The "ICP" is a different object than the "XICS". For historical reasons,
we have a number of places where we name a variable "icp" while it contains
a XICSState pointer. There *is* an ICPState structure too so this makes
the code really confusing.
This is a mechanical replacement of all those instances to use the name
"xics" instead. There should be no functional change.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[spapr_cpu_init has been moved to spapr_cpu_core.c, change there]
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
None of the other presenter functions directly mucks with the
internal state, so don't do it there either.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Leave the core ICP/ICS logic in xics.c and move the top level
class wrapper, hypercall and RTAS handlers to xics_spapr.c
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[add cpu.h in xics_spapr.c, move set_nr_irqs and set_nr_servers to
xics_spapr.c]
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The common class doesn't change, the KVM one is sPAPR specific. Rename
variables and functions to xics_spapr.
Retain the type name as "xics" to preserve migration for existing sPAPR
guests.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
These are spotted by coverity 1356936 and 1356937.
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1466387717-13740-1-git-send-email-zhaoshenglong@huawei.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
[dwg: Adjusted for context to apply without original series]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Version: GnuPG v1
iQEcBAABAgAGBQJXaFInAAoJEJykq7OBq3PI6VsH/0Sfgbdo1RksYuQwb/y92sCW
EN+lxUZ+OLfgrc8PYgNZwfSM3rsfYhznL0MAXOeEe7Ahabi07w7DhGR8WvwfAOlI
G96FRuvrIPfv5u6U6fwS4CvG3TIHVLxfHKCsTpPUmH8U5CNx/x/tpjNiWN1dj6t+
sXybSjYHfZfiZy2tI9MFIFWCdxnF/pl0QAPhbRqc8Y/RQTDrPKRjLpz+nitN/u96
5TS7KlELyQuP91YMmLceYSmIkHbxW703h+iE2n4hov0uZCP8Jil+2Jsd3ziQSRlL
j6LqexQ2ViBGdDSfiZGYES2VPlsHOCwb4G+IgWBStfZg1ppaXENvcDzPrgrB+L4=
=eUnF
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stefanha/tags/tracing-pull-request' into staging
# gpg: Signature made Mon 20 Jun 2016 21:29:27 BST
# gpg: using RSA key 0x9CA4ABB381AB73C8
# gpg: Good signature from "Stefan Hajnoczi <stefanha@redhat.com>"
# gpg: aka "Stefan Hajnoczi <stefanha@gmail.com>"
# Primary key fingerprint: 8695 A8BF D3F9 7CDA AC35 775A 9CA4 ABB3 81AB 73C8
* remotes/stefanha/tags/tracing-pull-request: (42 commits)
trace: split out trace events for linux-user/ directory
trace: split out trace events for qom/ directory
trace: split out trace events for target-ppc/ directory
trace: split out trace events for target-s390x/ directory
trace: split out trace events for target-sparc/ directory
trace: split out trace events for net/ directory
trace: split out trace events for audio/ directory
trace: split out trace events for ui/ directory
trace: split out trace events for hw/alpha/ directory
trace: split out trace events for hw/arm/ directory
trace: split out trace events for hw/acpi/ directory
trace: split out trace events for hw/vfio/ directory
trace: split out trace events for hw/s390x/ directory
trace: split out trace events for hw/pci/ directory
trace: split out trace events for hw/ppc/ directory
trace: split out trace events for hw/9pfs/ directory
trace: split out trace events for hw/i386/ directory
trace: split out trace events for hw/isa/ directory
trace: split out trace events for hw/sd/ directory
trace: split out trace events for hw/sparc/ directory
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Move all trace-events for files in the hw/intc/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-10-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Drop the old SysBus init function and use instance_init
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Acked-by: Michael Walle <michael@walle.cc>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Michael Walle <michael@walle.cc>
Use Coccinelle script to replace 'ret = E; return ret' with
'return E'. The script will do the substitution only when the
function return type and variable type are the same.
Manual fixups:
* audio/audio.c: coding style of "read (...)" and "write (...)"
* block/qcow2-cluster.c: wrap line to make it shorter
* block/qcow2-refcount.c: change indentation of wrapped line
* target-tricore/op_helper.c: fix coding style of
"remainder|quotient"
* target-mips/dsp_helper.c: reverted changes because I don't
want to argue about checkpatch.pl
* ui/qemu-pixman.c: fix line indentation
* block/rbd.c: restore blank line between declarations and
statements
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <1465855078-19435-4-git-send-email-ehabkost@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[Unused Coccinelle rule name dropped along with a redundant comment;
whitespace touched up in block/qcow2-cluster.c; stale commit message
paragraph deleted]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Fix missing includes of qemu/log.h, which broke compilation with the
simple trace backend (the default backend pulls in log.h implicitly
via trace.h).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Sergey Fedorov <sergey.fedorov@linaro.org>
Tested-by: Sergey Fedorov <sergey.fedorov@linaro.org>
Message-id: 1466416634-9798-1-git-send-email-peter.maydell@linaro.org
Add the CPU interface registers which deal with acknowledging
and dismissing interrupts.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Tested-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1465915112-29272-19-git-send-email-peter.maydell@linaro.org
Implement the registers in the GICv3 CPU interface which generate
new SGI interrupts.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Tested-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1465915112-29272-18-git-send-email-peter.maydell@linaro.org
Implement the gicv3_cpuif_update() function which deals with correctly
asserting IRQ and FIQ based on the current running priority of the CPU,
the priority of the highest priority pending interrupt and the CPU's
current exception level and security state.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Tested-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1465915112-29272-17-git-send-email-peter.maydell@linaro.org
Implement the CPU interface registers for the GICv3; these are
CPU system registers, not MMIO registers.
This commit implements all the registers which are simple
accessors for GIC state, but not those which act as interfaces
for acknowledging, dismissing or generating interrupts. (Those
will be added in a later commit.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Tested-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1465915112-29272-16-git-send-email-peter.maydell@linaro.org
Implement the code which updates the GIC state when an interrupt
input into the GIC is asserted.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Tested-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1465915112-29272-15-git-send-email-peter.maydell@linaro.org
Wire up the MMIO functions exposed by the distributor and the
redistributor into MMIO regions exposed by the GICv3 device.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Tested-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1465915112-29272-14-git-send-email-peter.maydell@linaro.org
Implement the redistributor registers of a GICv3.
Signed-off-by: Shlomo Pongratz <shlomo.pongratz@huawei.com>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Tested-by: Shannon Zhao <shannon.zhao@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1465915112-29272-13-git-send-email-peter.maydell@linaro.org
[PMM: significantly overhauled/rewritten:
* use the new data structures
* restructure register read/write to handle different width accesses
natively, since almost all registers are 32-bit only, rather
than implementing everything as byte accesses
* implemented security extension support
]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement the distributor registers of a GICv3.
Signed-off-by: Shlomo Pongratz <shlomo.pongratz@huawei.com>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Tested-by: Shannon Zhao <shannon.zhao@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1465915112-29272-12-git-send-email-peter.maydell@linaro.org
[PMM: significantly overhauled/rewritten:
* use the new bitmap data structures
* restructure register read/write to handle different width accesses
natively, since almost all registers are 32-bit only, rather
than implementing everything as byte accesses
* implemented security extension support
]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement the GICv3 logic to recalculate the highest priority pending
interrupt for each CPU after some part of the GIC state has changed.
We avoid unnecessary full recalculation where possible.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Tested-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1465915112-29272-11-git-send-email-peter.maydell@linaro.org
This patch includes the device class itself, some ID register
value functions which will be needed by both distributor
and redistributor, and some skeleton functions for handling
interrupts coming in and going out, which will be filled in
in a subsequent patch.
Signed-off-by: Shlomo Pongratz <shlomo.pongratz@huawei.com>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Tested-by: Shannon Zhao <shannon.zhao@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1465915112-29272-10-git-send-email-peter.maydell@linaro.org
[PMM: pulled this patch earlier in the sequence, and left
some code out of it for a later patch]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Add state structure descriptors for the GICv3 state. We mark
the KVM GICv3 device as having a migration blocker until the
code to save and restore the state in the kernel is implemented.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Tested-by: Shannon Zhao <shannon.zhao@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1465915112-29272-9-git-send-email-peter.maydell@linaro.org
[PMM: Adjust to renamed struct fields; switched to using uint32_t
array backed bitmaps; add migration blocker setting]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Move the GICv3 parent_irq and parent_fiq pointers into the
GICv3CPUState structure rather than giving them their own array.
This will make it easy to assert the IRQ and FIQ lines for a
particular CPU interface without having to know or calculate
the CPU index for the GICv3CPUState we are working on.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Tested-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1465915112-29272-8-git-send-email-peter.maydell@linaro.org
Add state information to GICv3 object structure and implement
arm_gicv3_common_reset().
This commit includes accessor functions for the fields which are
stored as bitmaps in uint32_t arrays.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Tested-by: Shannon Zhao <shannon.zhao@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1465915112-29272-7-git-send-email-peter.maydell@linaro.org
[PMM: significantly overhauled:
* Add missing qom/cpu.h include
* Remove legacy-only state fields (we can add them later if/when we add
legacy emulation)
* Use arrays of uint32_t to store the various distributor bitmaps,
and provide accessor functions for the various set/test/etc operations
* Add various missing register offset #defines
* Accessor macros which combine distributor and redistributor behaviour
removed
* Fields in state structures renamed to match architectural register names
* Corrected the reset value for GICR_IENABLER0 since we don't support
legacy mode
* Added ARM_LINUX_BOOT_IF interface for "we are directly booting a kernel in
non-secure" so that we can fake up the firmware-mandated reconfiguration
only when we need it
]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
XICS is setup for each CPU during initialization. Provide a routine
to undo the same when CPU is unplugged. While here, move ss->cs management
into xics from xics_kvm since there is nothing KVM specific in it.
Also ensure xics reset doesn't set irq for CPUs that are already unplugged.
This allows reboot of a VM that has undergone CPU hotplug and unplug
to work correctly.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
According to the platform specification, under certain conditions,
pending IO interruptions have to be cleared. Let's add an interface
for that.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Treat non-secure accesses to registers and bits in registers of secure
interrupts as RAZ/WI.
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Message-id: 1464273945-2055-1-git-send-email-jens.wiklander@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is to better emulate IOAPIC version 0x1X hardware. Linux kernel
leveraged this "feature" to do explicit EOI since EOI register is still
not introduced at that time. This will also fix the issue that level
triggered interrupts failed to work when IR enabled (tested with Linux
kernel version 4.5).
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <1462875682-1349-3-git-send-email-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently IOAPIC RO bits can be written. To be better aligned with
hardware, we should let them read-only.
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <1462875682-1349-2-git-send-email-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This is not visible with the default "log" trace backend. With other
backends however trace.h does not include qemu/log.h, resulting in
build failures.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1463745452-25831-2-git-send-email-pbonzini@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Memory barriers are needed also by Xen and, when the ioeventfd
bugs are fixed, by TCG as well.
sysemu/kvm.h is not anymore needed in sysemu/dma.h, move it to
the actual users.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
These are obviously critical to understanding interrupt delivery:
gic_enable_irq
gic_disable_irq
gic_set_irq (inbound irq from device models)
gic_update_set_irq (outbound irq to CPU)
gic_acknowledge_irq
The only one that I think might raise eyebrows is gic_update_bestirq, but I've
(sadly) debugged problems that ended up being caused by unexpected priorities.
Knowing that the GIC has an irq ready, but doesn't deliver to the CPU due to
priority, has also proven important.
Signed-off-by: Hollis Blanchard <hollis_blanchard@mentor.com>
Message-id: 1461252281-22399-1-git-send-email-hollis_blanchard@mentor.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
* Split the old SysBus init into an instance_init and a
DeviceClass::realize function
* Drop the old SysBus init function and use instance_init
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Split the old SysBus init into an instance_init and a
DeviceClass::realize function
* Drop the old SysBus init function
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: corrected "can not" to "cannot" in error message]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Drop the old SysBus init function and use instance_init
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Drop the old SysBus init function and use instance_init
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Drop the old SysBus init function and use instance_init
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Drop the old SysBus init function and use instance_init
* Split the exynos4210_irq_gate_init into an instance_init
and a DeviceClass::realize function
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Drop the old SysBus init function and use instance_init
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Drop the old SysBus init function and use instance_init
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch replaces get_ticks_per_sec() calls with the macro
NANOSECONDS_PER_SECOND. Also, as there are no callers, get_ticks_per_sec()
is then removed. This replacement improves the readability and
understandability of code.
For example,
timer_mod(fdctrl->result_timer,
qemu_clock_get_ns(QEMU_CLOCK_VIRTUAL) + (get_ticks_per_sec() / 50));
NANOSECONDS_PER_SECOND makes it obvious that qemu_clock_get_ns
matches the unit of the expression on the right side of the plus.
Signed-off-by: Rutuja Shah <rutu.shah.26@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 57cb38b included qapi/error.h into qemu/osdep.h to get the
Error typedef. Since then, we've moved to include qemu/osdep.h
everywhere. Its file comment explains: "To avoid getting into
possible circular include dependencies, this file should not include
any other QEMU headers, with the exceptions of config-host.h,
compiler.h, os-posix.h and os-win32.h, all of which are doing a
similar job to this file and are under similar constraints."
qapi/error.h doesn't do a similar job, and it doesn't adhere to
similar constraints: it includes qapi-types.h. That's in excess of
100KiB of crap most .c files don't actually need.
Add the typedef to qemu/typedefs.h, and include that instead of
qapi/error.h. Include qapi/error.h in .c files that need it and don't
get it now. Include qapi-types.h in qom/object.h for uint16List.
Update scripts/clean-includes accordingly. Update it further to match
reality: replace config.h by config-target.h, add sysemu/os-posix.h,
sysemu/os-win32.h. Update the list of includes in the qemu/osdep.h
comment quoted above similarly.
This reduces the number of objects depending on qapi/error.h from "all
of them" to less than a third. Unfortunately, the number depending on
qapi-types.h shrinks only a little. More work is needed for that one.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
[Fix compilation without the spice devel packages. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Implement a basic ASPEED VIC device model for the AST2400 SoC[1], with
enough functionality to boot an aspeed_defconfig Linux kernel. The model
implements the 'new' (revised) register set: While the hardware exposes
both the new and legacy register sets, accesses to the model's legacy
register set will not be serviced (however the access will be logged).
[1] http://www.aspeedtech.com/products.php?fPath=20&rId=376
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1458096317-25223-3-git-send-email-andrew@aj.id.au
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The GICv2 introduces a new CPU interface register GICC_DIR, which
allows an OS to split the "priority drop" and "deactivate interrupt"
parts of interrupt completion. Implement this register.
(Note that the register is at offset 0x1000 in the CPU interface,
which means it is on a different 4K page from all the other registers.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Sergey Fedorov <serge.fdrv@gmail.com>
Message-id: 1456854176-7813-1-git-send-email-peter.maydell@linaro.org
Using the return value to report errors is error prone:
- xics_alloc() returns -1 on error but spapr_vio_busdev_realize() errors
on 0
- xics_alloc_block() returns the unclear value of ics->offset - 1 on error
but both rtas_ibm_change_msi() and spapr_phb_realize() error on 0
This patch adds an errp argument to xics_alloc() and xics_alloc_block() to
report errors. The return value of these functions is a valid IRQ number
if errp is NULL. It is undefined otherwise.
The corresponding error traces get promotted to error messages. Note that
the "can't allocate IRQ" error message in spapr_vio_busdev_realize() also
moves to xics_alloc(). Similar error message consolidation isn't really
applicable to xics_alloc_block() because callers have extra context (device
config address, MSI or MSIX).
This fixes the issues mentioned above.
Based on previous work from Brian W. Hart.
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Similar to the previous patch, it's nice to have all functions
in the tree that involve a visitor and a name for conversion to
or from QAPI to consistently stick the 'name' parameter next
to the Visitor parameter.
Done by manually changing include/qom/object.h and qom/object.c,
then running this Coccinelle script and touching up the fallout
(Coccinelle insisted on adding some trailing whitespace).
@ rule1 @
identifier fn;
typedef Object, Visitor, Error;
identifier obj, v, opaque, name, errp;
@@
void fn
- (Object *obj, Visitor *v, void *opaque, const char *name,
+ (Object *obj, Visitor *v, const char *name, void *opaque,
Error **errp) { ... }
@@
identifier rule1.fn;
expression obj, v, opaque, name, errp;
@@
fn(obj, v,
- opaque, name,
+ name, opaque,
errp)
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <1454075341-13658-20-git-send-email-eblake@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
JSON uses "name":value, but many of our visitor interfaces were
called with visit_type_FOO(v, &value, name, errp). This can be
a bit confusing to have to mentally swap the parameter order to
match JSON order. It's particularly bad for visit_start_struct(),
where the 'name' parameter is smack in the middle of the
otherwise-related group of 'obj, kind, size' parameters! It's
time to do a global swap of the parameter ordering, so that the
'name' parameter is always immediately after the Visitor argument.
Additional reason in favor of the swap: the existing include/qjson.h
prefers listing 'name' first in json_prop_*(), and I have plans to
unify that file with the qapi visitors; listing 'name' first in
qapi will minimize churn to the (admittedly few) qjson.h clients.
Later patches will then fix docs, object.h, visitor-impl.h, and
those clients to match.
Done by first patching scripts/qapi*.py by hand to make generated
files do what I want, then by running the following Coccinelle
script to affect the rest of the code base:
$ spatch --sp-file script `git grep -l '\bvisit_' -- '**/*.[ch]'`
I then had to apply some touchups (Coccinelle insisted on TAB
indentation in visitor.h, and botched the signature of
visit_type_enum() by rewriting 'const char *const strings[]' to
the syntactically invalid 'const char*const[] strings'). The
movement of parameters is sufficient to provoke compiler errors
if any callers were missed.
// Part 1: Swap declaration order
@@
type TV, TErr, TObj, T1, T2;
identifier OBJ, ARG1, ARG2;
@@
void visit_start_struct
-(TV v, TObj OBJ, T1 ARG1, const char *name, T2 ARG2, TErr errp)
+(TV v, const char *name, TObj OBJ, T1 ARG1, T2 ARG2, TErr errp)
{ ... }
@@
type bool, TV, T1;
identifier ARG1;
@@
bool visit_optional
-(TV v, T1 ARG1, const char *name)
+(TV v, const char *name, T1 ARG1)
{ ... }
@@
type TV, TErr, TObj, T1;
identifier OBJ, ARG1;
@@
void visit_get_next_type
-(TV v, TObj OBJ, T1 ARG1, const char *name, TErr errp)
+(TV v, const char *name, TObj OBJ, T1 ARG1, TErr errp)
{ ... }
@@
type TV, TErr, TObj, T1, T2;
identifier OBJ, ARG1, ARG2;
@@
void visit_type_enum
-(TV v, TObj OBJ, T1 ARG1, T2 ARG2, const char *name, TErr errp)
+(TV v, const char *name, TObj OBJ, T1 ARG1, T2 ARG2, TErr errp)
{ ... }
@@
type TV, TErr, TObj;
identifier OBJ;
identifier VISIT_TYPE =~ "^visit_type_";
@@
void VISIT_TYPE
-(TV v, TObj OBJ, const char *name, TErr errp)
+(TV v, const char *name, TObj OBJ, TErr errp)
{ ... }
// Part 2: swap caller order
@@
expression V, NAME, OBJ, ARG1, ARG2, ERR;
identifier VISIT_TYPE =~ "^visit_type_";
@@
(
-visit_start_struct(V, OBJ, ARG1, NAME, ARG2, ERR)
+visit_start_struct(V, NAME, OBJ, ARG1, ARG2, ERR)
|
-visit_optional(V, ARG1, NAME)
+visit_optional(V, NAME, ARG1)
|
-visit_get_next_type(V, OBJ, ARG1, NAME, ERR)
+visit_get_next_type(V, NAME, OBJ, ARG1, ERR)
|
-visit_type_enum(V, OBJ, ARG1, ARG2, NAME, ERR)
+visit_type_enum(V, NAME, OBJ, ARG1, ARG2, ERR)
|
-VISIT_TYPE(V, OBJ, NAME, ERR)
+VISIT_TYPE(V, NAME, OBJ, ERR)
)
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <1454075341-13658-19-git-send-email-eblake@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
This module is specific to the bcm2836 (Pi2). It implements the top
level interrupt controller, and mailboxes used for inter-processor
synchronisation.
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-27-git-send-email-peter.maydell@linaro.org
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-13-git-send-email-peter.maydell@linaro.org
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-11-git-send-email-peter.maydell@linaro.org
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-9-git-send-email-peter.maydell@linaro.org
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-7-git-send-email-peter.maydell@linaro.org
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-6-git-send-email-peter.maydell@linaro.org
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-5-git-send-email-peter.maydell@linaro.org
Update the GIC ID registers (registers above 0xfe0) based on the GIC
revision instead of using the sames values for all GIC implementations.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Tested-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Message-id: 629e7fa5d47f2800e51cc1f18d12635f1eece349.1453333840.git.alistair.francis@xilinx.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Device init() methods aren't supposed to call hw_error(), they should
report the error and fail cleanly. Do that.
The errors are all device misconfiguration. All callers use
qdev_init_nofail(), so this patch merely converts hw_error() crashes
into &error_abort crashes. Improvement, because now it crashes closer
to where the misconfiguration bug would be, and a few more bad
examples of hw_error() use are gone.
Cc: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Markus Armbruster <armbru@pond.sub.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <1450370121-5768-3-git-send-email-armbru@redhat.com>
This patch adds support for split IRQ chip mode. When
KVM_CAP_SPLIT_IRQCHIP is enabled:
1.) The PIC, PIT, and IOAPIC are implemented in userspace while
the LAPIC is implemented by KVM.
2.) The software IOAPIC delivers interrupts to the KVM LAPIC via
kvm_set_irq. Interrupt delivery is configured via the MSI routing
table, for which routes are reserved in target-i386/kvm.c then
configured in hw/intc/ioapic.c
3.) KVM delivers IOAPIC EOIs via a new exit KVM_EXIT_IOAPIC_EOI,
which is handled in target-i386/kvm.c and relayed to the software
IOAPIC via ioapic_eoi_broadcast.
Signed-off-by: Matt Gingell <gingell@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Upon activating an interrupt, set the corresponding priority bit in the
APR/NSAPR registers without touching the currently set bits. In the event
of nested interrupts, the GIC will then have the information it needs to
restore the priority of the pre-empted interrupt once the higher priority
interrupt finishes execution.
Signed-off-by: François Baldassari <francois@pebble.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
arm_gic.c retrieves CPU number using either NUM_CPU(s) or s->num_cpu.
Such mixed-uses make source code inconsistent. This patch removes
NUM_CPU(s), which was defined for MPCore tweak long ago, and instead
favors s->num_cpu. The source is more consistent after this small tweak.
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Wei Huang <wei@redhat.com>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Message-id: 1446744293-32365-1-git-send-email-wei@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement the SYSRESETREQ bit of the AIRCR register
for armv7-m (ie. cortex-m3) to trigger a GPIO out.
Signed-off-by: Michael Davidsaver <mdavidsaver@gmail.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The goal is to have debug code always compiled during build.
We standardize all debug output on the following format:
[QOM_TYPE_NAME]reporting_function: debug message
We also replace IPRINTF with qemu_log_mask(). The qemu_log_mask() output
is following the same format as the above debug.
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Message-id: 29885ffea2577eaf2288c1d17fd87ee951748b49.1445781957.git.jcd@tribudubois.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently, if the kernel does not have live migration API, the migration
will still be attempted, but vGIC save/restore functions will just not do
anything. This will result in a broken machine state.
This patch fixes the problem by adding migration blocker if kernel API is
not supported.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
openpic is a programmable interrupt controller, so
add it to the misc category.
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This should help clarify the purpose of the function that returns
the host system's CPU cycle count.
Signed-off-by: Christopher Covington <cov@codeaurora.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
ppc portion
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
After CPU hotplug has been converted to BUS-less hot-plug infrastructure,
the only function ICC bus performs is to propagate reset to LAPICs. However
LAPIC could be reset by registering its reset handler after all device are
initialized.
Do so and drop ~30LOC of not needed anymore ICCBus related code.
Signed-off-by: Chen Fan <chen.fan.fnst@cn.fujitsu.com>
Signed-off-by: Zhu Guihua <zhugh.fnst@cn.fujitsu.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
When ICC bus/bridge is removed, APIC MMIO will be left
unmapped since it was mapped into system's address space
indirectly by ICC bridge.
Fix it by moving mapping into APIC code, so it would be
possible to remove ICC bus/bridge code later.
Signed-off-by: Chen Fan <chen.fan.fnst@cn.fujitsu.com>
Signed-off-by: Zhu Guihua <zhugh.fnst@cn.fujitsu.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Added support emulator for the hmp command "info ioapic"
Signed-off-by: Pavel Butsykin <pbutsykin@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Andreas Färber <afaerber@suse.de>
Message-Id: <1442927901-1084-10-git-send-email-den@openvz.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Added prefix APIC_ for determining the constant of a particular subsystem,
improve the overall readability and match other constant names.
Signed-off-by: Pavel Butsykin <pbutsykin@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Andreas Färber <afaerber@suse.de>
Message-Id: <1442927901-1084-3-git-send-email-den@openvz.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move apic_get_bit(), apic_set_bit() to apic_internal.h, make the apic_get_ppr
symbol external. It's necessary to work with isr, tmr, irr and ppr outside
hw/intc/apic.c
Signed-off-by: Pavel Butsykin <pbutsykin@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Andreas Färber <afaerber@suse.de>
Message-Id: <1442927901-1084-2-git-send-email-den@openvz.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The arbitration register should read to the same value as the
IOAPIC id register. Fixes kvm-unit-tests ioapic.flat.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If a level-triggered interrupt goes down and back up before the
corresponding EOI, it should be coalesced. This fixes one testcase
in kvm-unit-tests' ioapic.flat.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This is the initial version of KVM-accelerated GICv3 support.
State load and save are not yet supported, live migration is
not possible.
In order to get correct class name in a simpler way, gicv3_class_name()
function is implemented, similar to gic_class_name().
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Ashok kumar <ashoks@broadcom.com>
Message-id: 69d8f01d14994d7a1a140e96aef59fd332d02293.1441784344.git.p.fedin@samsung.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some functions previously used only by vGICv2 are useful also for vGICv3
implementation. Untie them from GICState and make accessible from within
other modules:
- kvm_arm_gic_set_irq()
- kvm_gic_supports_attr() - moved to common code and renamed to
kvm_device_check_attr()
- kvm_gic_access() - turned into GIC-independent kvm_device_access().
Data pointer changed to void * because some GICv3 registers are
64-bit wide
Some of these changes are not used right now, but they will be helpful for
implementing live migration.
Actually kvm_dist_get() and kvm_dist_put() could also be made reusable, but
they would require two extra parameters (s->dev_fd and s->num_cpu) as well as
lots of typecasts of 's' to DeviceState * and back to GICState *. This makes
the code very ugly so i decided to stop at this point. I tried also an
approach with making a base class for all possible GICs, but it would contain
only three variables (dev_fd, cpu_num and irq_num), and accessing them through
the rest of the code would be again tedious (either ugly casts or qemu-style
separate object pointer). So i disliked it too.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Tested-by: Ashok kumar <ashoks@broadcom.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 2ef56d1dd64ffb75ed02a10dcdaf605e5b8ff4f8.1441784344.git.p.fedin@samsung.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This class is to be used by both software and KVM implementations of GICv3
Currently it is mostly a placeholder, but in future it is supposed to hold
qemu's representation of GICv3 state, which is necessary for migration.
The interface of this class is fully compatible with GICv2 one. This is
done in order to simplify integration with existing code.
Signed-off-by: Shlomo Pongratz <shlomo.pongratz@huawei.com>
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Reviewed-by: Eric Auger <eric.auger@linaro.org>
Tested-by: Ashok kumar <ashoks@broadcom.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: aff8baaee493cdcab0694b4a1d4dd5ff27c37ed2.1441784344.git.p.fedin@samsung.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
A number of source files have statements accidentally
terminated by a double semicolon - eg 'foo = bar;;'.
This is harmless but a mistake none the less.
The tcg/ia64/tcg-target.c file is whitelisted because
it has valid use of ';;' in a comment containing assembly
code.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
If we directly boot a kernel in NonSecure on a system where the GIC
supports the security extensions then we must cause the GIC to
configure its interrupts into group 1 (NonSecure) rather than the
usual group 0, and with their initial priority set to the highest
NonSecure priority rather than the usual highest Secure priority.
Otherwise the guest kernel will be unable to use any interrupts.
Implement this behaviour, controlled by a flag which we set if
appropriate when the ARM bootloader code calls our ARMLinuxBootIf
interface callback.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1441383782-24378-4-git-send-email-peter.maydell@linaro.org
Although we were correctly handling interrupts becoming active
and then inactive, we weren't actually exposing this to the guest
by setting the 'active' flag for the interrupt, so reads
of GICD_ICACTIVERn and GICD_ISACTIVERn would generally incorrectly
return zeroes. Correct this oversight.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1438089748-5528-6-git-send-email-peter.maydell@linaro.org
The running_irq and last_active arrays represent state which
doesn't exist in a real hardware GIC. The only thing we use
them for is updating the running priority when an interrupt
is completed, but in fact we can use the active-priority
registers to do this. The running priority is always the
priority corresponding to the lowest set bit in the active
priority registers, because only one interrupt at any
particular priority can be active at once.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1438089748-5528-5-git-send-email-peter.maydell@linaro.org
A GICv2 has both GICC_APR<n> and GICC_NSAPR<n> registers, with
the latter holding the active priority bits for Group 1 interrupts
(usually Nonsecure interrupts), and the Nonsecure view of the
GICC_APR<n> is the second half of the GICC_NSAPR<n> registers.
Turn our half-hearted implementation of APR<n> into a proper
implementation of both APR<n> and NSAPR<n>:
* Add the underlying state for NSAPR<n>
* Make sure APR<n> aren't visible for pre-GICv2
* Implement reading of NSAPR<n>
* Make non-secure reads of APR<n> behave correctly
* Implement writing to APR<n> and NSAPR<n>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1438089748-5528-4-git-send-email-peter.maydell@linaro.org
Priority values for the GIC are divided into a "group priority"
and a "subpriority" (with the division being determined by the
binary point register). The running priority is only determined
by the group priority of the active interrupts, not the
subpriority. In particular, this means that there can't be more
than one active interrupt at any particular group priority.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1438089748-5528-3-git-send-email-peter.maydell@linaro.org
Change the implementation of the Interrupt Control and State Register
in the v7M NVIC to not use the running_irq and last_active internal
state fields in the GIC. These fields don't correspond to state in
a real GIC and will be removed soon.
The changes to the ICSR are:
* the VECTACTIVE field is documented as identical to the IPSR[8:0]
field, so implement it that way
* implement RETTOBASE via looking at the active state bits
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1438089748-5528-2-git-send-email-peter.maydell@linaro.org
When we add new adapter routes we call kvm_irqchip_add_route() for every
virtqueue and in the same step also do the KVM_SET_GSI_ROUTING ioctl.
This is unnecessary costly as the interface allows us to set multiple
routes in one go. Let's first add all routes to the table stored in the
global kvm_state and then do the ioctl to commit the routes to the
in-kernel irqchip.
This saves us several ioctls to the kernel where for each call a list
is reallocated and populated.
Signed-off-by: Jens Freimann <jfrei@linux.vnet.ibm.com>
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Extracted duplicated initialization code from SW-emulated and KVM GIC
implementations and put into gic_init_irqs_and_mmio()
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Message-id: 8ea5b2781ef39cb5989420987fc73c70e377687d.1438758065.git.p.fedin@samsung.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
