ps2.c only needs to be compiled if we are building pckbd.c or pl050.c.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190411182240.5957-1-thuth@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Make VIRTIO_INPUT_HOST depend on VIRTIO_INPUT.
Use CONFIG_VIRTIO_INPUT_HOST in Makefile.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20190510105137.17481-2-kraxel@redhat.com
Add a new virtio-input device, which connects to a vhost-user
backend.
Instead of reading configuration directly from an input device /
evdev (like virtio-input-host), it reads it over vhost-user protocol
with {SET,GET}_CONFIG messages. The vhost-user-backend handles the
queues & events setup.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20190503130034.24916-5-marcandre.lureau@redhat.com
[ kraxel: drop -{non-,}transitional variants ]
[ kraxel: fix "make check" on !linux ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Since uWireSlave is only used in this new header, there is no
need to expose it via "qemu/typedefs.h".
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190412165416.7977-9-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190412165416.7977-8-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some trace points are attributed to the wrong source file. Happens
when we neglect to update trace-events for code motion, or add events
in the wrong place, or misspell the file name.
Clean up with help of cleanup-trace-events.pl. Same funnies as in the
previous commit, of course. Manually shorten its change to
linux-user/trace-events to */signal.c.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-id: 20190314180929.27722-6-armbru@redhat.com
Message-Id: <20190314180929.27722-6-armbru@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
We spell out sub/dir/ in sub/dir/trace-events' comments pointing to
source files. That's because when trace-events got split up, the
comments were moved verbatim.
Delete the sub/dir/ part from these comments. Gets rid of several
misspellings.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190314180929.27722-3-armbru@redhat.com
Message-Id: <20190314180929.27722-3-armbru@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
I had to include an enum for audio sampling formats into qapi, but that
meant duplicating the audfmt_e enum. This patch replaces audfmt_e and
associated values with the qapi generated AudioFormat enum.
This patch is mostly a search-and-replace, except for switches where the
qapi generated AUDIO_FORMAT_MAX caused problems.
Signed-off-by: Kővágó, Zoltán <DirtY.iCE.hu@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 01251b2758a1679c66842120b77c0fb46d7d0eaf.1552083282.git.DirtY.iCE.hu@gmail.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-42-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Acked-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-38-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20190123065618.3520-36-yang.zhong@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The make_device_config.sh script is replaced by minikconf, which
is modified to support the same command line as its predecessor.
The roots of the parsing are default-configs/*.mak, Kconfig.host and
hw/Kconfig. One difference with make_device_config.sh is that all symbols
have to be defined in a Kconfig file, including those coming from the
configure script. This is the reason for the Kconfig.host file introduced
in the previous patch. Whenever a file in default-configs/*.mak used
$(...) to refer to a config-host.mak symbol, this is replaced by a
Kconfig dependency; this part must be done already in this patch
for bisectability.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Acked-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190123065618.3520-28-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The Kconfig files were generated mostly with this script:
for i in `grep -ho CONFIG_[A-Z0-9_]* default-configs/* | sort -u`; do
set fnord `git grep -lw $i -- 'hw/*/Makefile.objs' `
shift
if test $# = 1; then
cat >> $(dirname $1)/Kconfig << EOF
config ${i#CONFIG_}
bool
EOF
git add $(dirname $1)/Kconfig
else
echo $i $*
fi
done
sed -i '$d' hw/*/Kconfig
for i in hw/*; do
if test -d $i && ! test -f $i/Kconfig; then
touch $i/Kconfig
git add $i/Kconfig
fi
done
Whenever a symbol is referenced from multiple subdirectories, the
script prints the list of directories that reference the symbol.
These symbols have to be added manually to the Kconfig files.
Kconfig.host and hw/Kconfig were created manually.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Yang Zhong <yang.zhong@intel.com>
Message-Id: <20190123065618.3520-27-yang.zhong@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It is never supposed to fail and cannot return an error, so just
have it return the proper type. Have it return 0xff on nothing
available, since that's what would happen on a real bus.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20181016112232.23241-1-dgilbert@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
When building with TSC_VERBOSE not defined, we get:
CC arm-softmmu/hw/input/tsc210x.o
hw/input/tsc210x.c: In function ‘tsc2102_data_register_write’:
hw/input/tsc210x.c:554:5: error: label at end of compound statement
default:
^~~~~~~
hw/input/tsc210x.c: In function ‘tsc2102_control_register_write’:
hw/input/tsc210x.c:638:5: error: label at end of compound statement
bad_reg:
^~~~~~~
hw/input/tsc210x.c: In function ‘tsc2102_audio_register_write’:
hw/input/tsc210x.c:766:5: error: label at end of compound statement
default:
^~~~~~~
make[1]: *** [rules.mak:69: hw/input/tsc210x.o] Error 1
Fix this by replacing the culprit fprintf(stderr) calls by a more
recent API: qemu_log_mask(LOG_GUEST_ERROR). Other fprintf() calls
are left untouched.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Message-Id: <20190204204517.23698-1-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Sets the category of i8042 device as DEVICE_CATEGORY_INPUT
Devices should be assigned to one of DEVICE_CATEGORY_XXXX.
Signed-off-by: kumar sourav <sourav.jb1988@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20190125151440.13794-1-sourav.jb1988@gmail.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Most files that have TABs only contain a handful of them. Change
them to spaces so that we don't confuse people.
disas, standard-headers, linux-headers and libdecnumber are imported
from other projects and probably should be exempted from the check.
Outside those, after this patch the following files still contain both
8-space and TAB sequences at the beginning of the line. Many of them
have a majority of TABs, or were initially committed with all tabs.
bsd-user/i386/target_syscall.h
bsd-user/x86_64/target_syscall.h
crypto/aes.c
hw/audio/fmopl.c
hw/audio/fmopl.h
hw/block/tc58128.c
hw/display/cirrus_vga.c
hw/display/xenfb.c
hw/dma/etraxfs_dma.c
hw/intc/sh_intc.c
hw/misc/mst_fpga.c
hw/net/pcnet.c
hw/sh4/sh7750.c
hw/timer/m48t59.c
hw/timer/sh_timer.c
include/crypto/aes.h
include/disas/bfd.h
include/hw/sh4/sh.h
libdecnumber/decNumber.c
linux-headers/asm-generic/unistd.h
linux-headers/linux/kvm.h
linux-user/alpha/target_syscall.h
linux-user/arm/nwfpe/double_cpdo.c
linux-user/arm/nwfpe/fpa11_cpdt.c
linux-user/arm/nwfpe/fpa11_cprt.c
linux-user/arm/nwfpe/fpa11.h
linux-user/flat.h
linux-user/flatload.c
linux-user/i386/target_syscall.h
linux-user/ppc/target_syscall.h
linux-user/sparc/target_syscall.h
linux-user/syscall.c
linux-user/syscall_defs.h
linux-user/x86_64/target_syscall.h
slirp/cksum.c
slirp/if.c
slirp/ip.h
slirp/ip_icmp.c
slirp/ip_icmp.h
slirp/ip_input.c
slirp/ip_output.c
slirp/mbuf.c
slirp/misc.c
slirp/sbuf.c
slirp/socket.c
slirp/socket.h
slirp/tcp_input.c
slirp/tcpip.h
slirp/tcp_output.c
slirp/tcp_subr.c
slirp/tcp_timer.c
slirp/tftp.c
slirp/udp.c
slirp/udp.h
target/cris/cpu.h
target/cris/mmu.c
target/cris/op_helper.c
target/sh4/helper.c
target/sh4/op_helper.c
target/sh4/translate.c
tcg/sparc/tcg-target.inc.c
tests/tcg/cris/check_addo.c
tests/tcg/cris/check_moveq.c
tests/tcg/cris/check_swap.c
tests/tcg/multiarch/test-mmap.c
ui/vnc-enc-hextile-template.h
ui/vnc-enc-zywrle.h
util/envlist.c
util/readline.c
The following have only TABs:
bsd-user/i386/target_signal.h
bsd-user/sparc64/target_signal.h
bsd-user/sparc64/target_syscall.h
bsd-user/sparc/target_signal.h
bsd-user/sparc/target_syscall.h
bsd-user/x86_64/target_signal.h
crypto/desrfb.c
hw/audio/intel-hda-defs.h
hw/core/uboot_image.h
hw/sh4/sh7750_regnames.c
hw/sh4/sh7750_regs.h
include/hw/cris/etraxfs_dma.h
linux-user/alpha/termbits.h
linux-user/arm/nwfpe/fpopcode.h
linux-user/arm/nwfpe/fpsr.h
linux-user/arm/syscall_nr.h
linux-user/arm/target_signal.h
linux-user/cris/target_signal.h
linux-user/i386/target_signal.h
linux-user/linux_loop.h
linux-user/m68k/target_signal.h
linux-user/microblaze/target_signal.h
linux-user/mips64/target_signal.h
linux-user/mips/target_signal.h
linux-user/mips/target_syscall.h
linux-user/mips/termbits.h
linux-user/ppc/target_signal.h
linux-user/sh4/target_signal.h
linux-user/sh4/termbits.h
linux-user/sparc64/target_syscall.h
linux-user/sparc/target_signal.h
linux-user/x86_64/target_signal.h
linux-user/x86_64/termbits.h
pc-bios/optionrom/optionrom.h
slirp/mbuf.h
slirp/misc.h
slirp/sbuf.h
slirp/tcp.h
slirp/tcp_timer.h
slirp/tcp_var.h
target/i386/svm.h
target/sparc/asi.h
target/xtensa/core-dc232b/xtensa-modules.inc.c
target/xtensa/core-dc233c/xtensa-modules.inc.c
target/xtensa/core-de212/core-isa.h
target/xtensa/core-de212/xtensa-modules.inc.c
target/xtensa/core-fsf/xtensa-modules.inc.c
target/xtensa/core-sample_controller/core-isa.h
target/xtensa/core-sample_controller/xtensa-modules.inc.c
target/xtensa/core-test_kc705_be/core-isa.h
target/xtensa/core-test_kc705_be/xtensa-modules.inc.c
tests/tcg/cris/check_abs.c
tests/tcg/cris/check_addc.c
tests/tcg/cris/check_addcm.c
tests/tcg/cris/check_addoq.c
tests/tcg/cris/check_bound.c
tests/tcg/cris/check_ftag.c
tests/tcg/cris/check_int64.c
tests/tcg/cris/check_lz.c
tests/tcg/cris/check_openpf5.c
tests/tcg/cris/check_sigalrm.c
tests/tcg/cris/crisutils.h
tests/tcg/cris/sys.c
tests/tcg/i386/test-i386-ssse3.c
ui/vgafont.h
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20181213223737.11793-3-pbonzini@redhat.com>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Wainer dos Santos Moschetta <wainersm@redhat.com>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Eric Blake <eblake@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Stefan Markovic <smarkovic@wavecomp.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The qmp/hmp command 'system_wakeup' is simply a direct call to
'qemu_system_wakeup_request' from vl.c. This function verifies if
runstate is SUSPENDED and if the wake up reason is valid before
proceeding. However, no error or warning is thrown if any of those
pre-requirements isn't met. There is no way for the caller to
differentiate between a successful wakeup or an error state caused
when trying to wake up a guest that wasn't suspended.
This means that system_wakeup is silently failing, which can be
considered a bug. Adding error handling isn't an API break in this
case - applications that didn't check the result will remain broken,
the ones that check it will have a chance to deal with it.
Adding to that, the commit before previous created a new QMP API called
query-current-machine, with a new flag called wakeup-suspend-support,
that indicates if the guest has the capability of waking up from suspended
state. Although such guest will never reach SUSPENDED state and erroring
it out in this scenario would suffice, it is more informative for the user
to differentiate between a failure because the guest isn't suspended versus
a failure because the guest does not have support for wake up at all.
All this considered, this patch changes qmp_system_wakeup to check if
the guest is capable of waking up from suspend, and if it is suspended.
After this patch, this is the output of system_wakeup in a guest that
does not have wake-up from suspend support (ppc64):
(qemu) system_wakeup
wake-up from suspend is not supported by this guest
(qemu)
And this is the output of system_wakeup in a x86 guest that has the
support but isn't suspended:
(qemu) system_wakeup
Unable to wake up: guest is not in suspended state
(qemu)
Reported-by: Balamuruhan S <bala24@linux.vnet.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20181205194701.17836-4-danielhb413@gmail.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Use DeviceClass rather than SysBusDeviceClass in
pl050_class_init().
Cc: peter.maydell@linaro.org
Cc: qemu-arm@nongnu.org
Signed-off-by: Mao Zhongyi <maozhongyi@cmss.chinamobile.com>
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20181130093852.20739-10-maozhongyi@cmss.chinamobile.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use DeviceClass rather than SysBusDeviceClass in
milkymist_softusb_class_init().
Cc: michael@walle.cc
Signed-off-by: Mao Zhongyi <maozhongyi@cmss.chinamobile.com>
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20181130093852.20739-9-maozhongyi@cmss.chinamobile.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
A check for scan_enabled has been added to ps2_keyboard_event in commit
143c04c7e0 to prevent stream corruption.
This works well as long as operating system is resetting keyboard, or enabling it.
This fixes IBM 40p firmware, which doesn't bother sending KBD_CMD_RESET,
KBD_CMD_ENABLE or KBD_CMD_RESET_ENABLE before trying to use the keyboard.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20181021190721.2148-1-hpoussin@reactos.org
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Commit 2858ab09e6 changed
PS/2 keyboard/mouse buffers to the standard size. However, its state
may change when migrating from the old buffer size and therefore irq needs
updating. But this change made wrong, because it throws the whole queue
if there are too much data instead of cropping it.
That commit also updates irq (because the queue state may change).
But updating the irq may change the VM state (and determinism of
the execution). E.g., when replaying the execution, one may save
the VM state and the state of the interrupt controller will be updated
at the moment of saving, instead of using the recorded update events.
This patch makes the queue update deterministic: it removes the update_irq
call and crops the queue to prevent losing the characters and changing
the required irq status.
Signed-off-by: Pavel Dovgalyuk <Pavel.Dovgaluk@ispras.ru>
Message-Id: <20180511081601.14610.39946.stgit@pasha-VirtualBox>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 20180624040609.17572-3-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 20180624040609.17572-2-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In commit 802cbcb730, most issues have been fixed when qemu guest
migration. But the queue size still need to check whether is equal to
PS2_QUEUE_SIZE. If yes, the wptr should set as 0. Or, wptr would larger
than PS2_QUEUE_SIZE and never come back when ps2_queue_noirq is called.
This could lead to OOB access, add check to avoid it.
Signed-off-by: liujunjie <liujunjie23@huawei.com>
Reviewed-by: Gonglei <arei.gonglei@huawei.com>
Message-id: 20180607080237.12360-1-liujunjie23@huawei.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
MacOS 9 has a bug in its PMU driver whereby after configuring the ADB bus
devices it sends another write to reg 3 on both devices resetting them
both back to the same address.
Add a new disable_direct_reg3_writes property to ADBDevice to disable these
direct writes which can enabled just for the upcoming pmu-adb support.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
According to the Apple ADB documentation, register 3 is a 2-byte register
with the device address in the first byte, and the handler ID in the second
byte.
This is currently the opposite away to which QEMU returns them so switch the
order around.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Convert the pckbd device away from using the old_mmio field
of MemoryRegionOps. This change only affects the memory-mapped
variant of the i8042, which is used by the Unicore32 'puv3'
board and the MIPS Jazz boards 'magnum' and 'pica61'.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180601141223.26630-6-peter.maydell@linaro.org
This is only half of the work, because the proxy devices (virtio-*-pci,
virtio-*-ccw, etc.) are still included unconditionally. It is still a
move in the right direction.
Based-on: <20180522194943.24871-1-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
I2CSlaveClass::init is no more used, remove it.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180419212727.26095-3-f4bug@amsat.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180528144509.15812-3-armbru@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This fixes an issue by adding bounds checking to multi-byte packets
where the PS/2 mouse data stream may become corrupted due to data being
discarded when the PS/2 ringbuffer is full.
Interrupts for Multi-byte responses are postponed until the final byte
has been queued.
These changes fix a bug where windows guests drop the mouse device
entirely requring the guest to be restarted.
Signed-off-by: Geoffrey McRae <geoff@hostfission.com>
Message-Id: <20180507150310.2FEA0381924@moya.office.hostfission.com>
[ kraxel: codestyle fixes ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This allows guest's to correctly reinitialize and identify the mouse
should the guest decide to re-scan or reset during mouse input events.
When the guest sends the "Identify" command, due to the PC's hardware
architecutre it is impossible to reliably determine the response from
the command amongst other streaming data, such as mouse or keyboard
events. Standard practice is for the guest to disable the device and
then issue the identify command, so this must be obeyed.
Signed-off-by: Geoffrey McRae <geoff@hostfission.com>
Message-Id: <20180507150303.7486B381924@moya.office.hostfission.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au> (hw/ppc)
Message-Id: <20180308223946.26784-4-f4bug@amsat.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This is useful to help diagnose problems related to address clashes during
MacOS 9 boot.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Replace the keymap_qcode table with automatically generated
tables.
Missing entries in keymap_qcode now fixed:
Q_KEY_CODE_ASTERISK -> KEY_KPASTERISK
Q_KEY_CODE_KP_MULTIPLY -> KEY_KPASTERISK
Q_KEY_CODE_STOP -> KEY_STOP
Q_KEY_CODE_AGAIN -> KEY_AGAIN
Q_KEY_CODE_PROPS -> KEY_PROPS
Q_KEY_CODE_UNDO -> KEY_UNDO
Q_KEY_CODE_FRONT -> KEY_FRONT
Q_KEY_CODE_COPY -> KEY_COPY
Q_KEY_CODE_OPEN -> KEY_OPEN
Q_KEY_CODE_PASTE -> KEY_PASTE
Q_KEY_CODE_FIND -> KEY_FIND
Q_KEY_CODE_CUT -> KEY_CUT
Q_KEY_CODE_LF -> KEY_LINEFEED
Q_KEY_CODE_HELP -> KEY_HELP
Q_KEY_CODE_COMPOSE -> KEY_COMPOSE
Q_KEY_CODE_RO -> KEY_RO
Q_KEY_CODE_HIRAGANA -> KEY_HIRAGANA
Q_KEY_CODE_HENKAN -> KEY_HENKAN
Q_KEY_CODE_YEN -> KEY_YEN
Q_KEY_CODE_KP_COMMA -> KEY_KPCOMMA
Q_KEY_CODE_KP_EQUALS -> KEY_KPEQUAL
Q_KEY_CODE_POWER -> KEY_POWER
Q_KEY_CODE_SLEEP -> KEY_SLEEP
Q_KEY_CODE_WAKE -> KEY_WAKEUP
Q_KEY_CODE_AUDIONEXT -> KEY_NEXTSONG
Q_KEY_CODE_AUDIOPREV -> KEY_PREVIOUSSONG
Q_KEY_CODE_AUDIOSTOP -> KEY_STOPCD
Q_KEY_CODE_AUDIOPLAY -> KEY_PLAYPAUSE
Q_KEY_CODE_AUDIOMUTE -> KEY_MUTE
Q_KEY_CODE_VOLUMEUP -> KEY_VOLUMEUP
Q_KEY_CODE_VOLUMEDOWN -> KEY_VOLUMEDOWN
Q_KEY_CODE_MEDIASELECT -> KEY_MEDIA
Q_KEY_CODE_MAIL -> KEY_MAIL
Q_KEY_CODE_CALCULATOR -> KEY_CALC
Q_KEY_CODE_COMPUTER -> KEY_COMPUTER
Q_KEY_CODE_AC_HOME -> KEY_HOMEPAGE
Q_KEY_CODE_AC_BACK -> KEY_BACK
Q_KEY_CODE_AC_FORWARD -> KEY_FORWARD
Q_KEY_CODE_AC_REFRESH -> KEY_REFRESH
Q_KEY_CODE_AC_BOOKMARKS -> KEY_BOOKMARKS
NB, the virtio-input device reports a bitmask to the guest driver that
has a bit set for each Linux keycode that the host is able to send to
the guest.
Thus by adding these extra key mappings we are technically changing the
host<->guest ABI. This would also happen any time we defined new mappings
for QEMU keycodes in future.
When a keycode is removed from the list of possible keycodes that host can
send to the guest, it means that the guest OS will think it is possible
to receive a key that in pratice can never be generated, which is harmless.
When a keycode is added to the list of possible keycodes that the host can
send to the guest, it means that the guest OS can see an unexpected event.
The Linux virtio_input.c driver code simply forwards this event to the
input_event() method in the Linux input subsystem. This in turn calls
input_handle_event(), which then calls input_get_disposition(). This method
checks if the input event is present in the permitted keys bitmap, and if
not returns INPUT_IGNORE_EVENT. Thus the unexpected event will get dropped,
which is harmless.
If the guest OS reboots, or otherwise re-initializes the virt-input device,
it will read the new keycode bitmap. No matter how many keys are defined,
the config space has a fixed 128 byte bitmap. There is, however, a size
field defiend which says how many bytes in the bitmap are used. So the guest
OS reads the size of the bitmap, and then it reads the data from bitmap upto
the designated size. So if the guest OS re-initializes at precisely the time
that QEMU is migrated across versions, in the worst case, it could conceivably
read the old size field, but then get the newly updated bitmap. If a key were
added this is harmless, since it simply means it may not process the newly
added key. If a key were removed, then it could be readnig a byte from the
bitmap that was not initialized. Fortunately QEMU always memsets() the entire
bitmap to 0, prior to setting keybits. Thus the guest OS will simply read
zeros, which is again harmless.
Based on this analysis, it is believed that there is no need to preserve the
virtio-input-hid keymaps across migration, as the host<->guest ABI change is
harmless and self-resolving at time of guest reboot.
NB, this behaviour should perhaps be formalized in the virtio-input spec
to declare how guest OS drivers should be written to be robust in their
handling of the potentially changable key bitmaps.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20180117164118.8510-5-berrange@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Replace the qcode_to_keycode_set1, qcode_to_keycode_set2,
and qcode_to_keycode_set3 tables with automatically
generated tables.
Missing entries in qcode_to_keycode_set1 now fixed:
- Q_KEY_CODE_SYSRQ -> 0x54
- Q_KEY_CODE_PRINT -> 0x54 (NB ignored due to special case)
- Q_KEY_CODE_AGAIN -> 0xe005
- Q_KEY_CODE_PROPS -> 0xe006
- Q_KEY_CODE_UNDO -> 0xe007
- Q_KEY_CODE_FRONT -> 0xe00c
- Q_KEY_CODE_COPY -> 0xe078
- Q_KEY_CODE_OPEN -> 0x64
- Q_KEY_CODE_PASTE -> 0x65
- Q_KEY_CODE_CUT -> 0xe03c
- Q_KEY_CODE_LF -> 0x5b
- Q_KEY_CODE_HELP -> 0xe075
- Q_KEY_CODE_COMPOSE -> 0xe05d
- Q_KEY_CODE_PAUSE -> 0xe046
- Q_KEY_CODE_KP_EQUALS -> 0x59
And some mistakes corrected:
- Q_KEY_CODE_HIRAGANA was mapped to 0x70 (Katakanahiragana)
instead of of 0x77 (Hirigana)
- Q_KEY_CODE_MENU was incorrectly mapped to the compose
scancode (0xe05d) and is now mapped to 0xe01e
- Q_KEY_CODE_FIND was mapped to 0xe065 (Search) instead
of to 0xe041 (Find)
- Q_KEY_CODE_POWER, SLEEP & WAKE had 0x0e instead of 0xe0
as the prefix
Missing entries in qcode_to_keycode_set2 now fixed:
- Q_KEY_CODE_PRINT -> 0x7f (NB ignored due to special case)
- Q_KEY_CODE_COMPOSE -> 0xe02f
- Q_KEY_CODE_PAUSE -> 0xe077
- Q_KEY_CODE_KP_EQUALS -> 0x0f
And some mistakes corrected:
- Q_KEY_CODE_HIRAGANA was mapped to 0x13 (Katakanahiragana)
instead of of 0x62 (Hirigana)
- Q_KEY_CODE_MENU was incorrectly mapped to the compose
scancode (0xe02f) and is now not mapped
- Q_KEY_CODE_FIND was mapped to 0xe010 (Search) and is now
not mapped.
- Q_KEY_CODE_POWER, SLEEP & WAKE had 0x0e instead of 0xe0
as the prefix
Missing entries in qcode_to_keycode_set3 now fixed:
- Q_KEY_CODE_ASTERISK -> 0x7e
- Q_KEY_CODE_SYSRQ -> 0x57
- Q_KEY_CODE_LESS -> 0x13
- Q_KEY_CODE_STOP -> 0x0a
- Q_KEY_CODE_AGAIN -> 0x0b
- Q_KEY_CODE_PROPS -> 0x0c
- Q_KEY_CODE_UNDO -> 0x10
- Q_KEY_CODE_COPY -> 0x18
- Q_KEY_CODE_OPEN -> 0x20
- Q_KEY_CODE_PASTE -> 0x28
- Q_KEY_CODE_FIND -> 0x30
- Q_KEY_CODE_CUT -> 0x38
- Q_KEY_CODE_HELP -> 0x09
- Q_KEY_CODE_COMPOSE -> 0x8d
- Q_KEY_CODE_AUDIONEXT -> 0x93
- Q_KEY_CODE_AUDIOPREV -> 0x94
- Q_KEY_CODE_AUDIOSTOP -> 0x98
- Q_KEY_CODE_AUDIOMUTE -> 0x9c
- Q_KEY_CODE_VOLUMEUP -> 0x95
- Q_KEY_CODE_VOLUMEDOWN -> 0x9d
- Q_KEY_CODE_CALCULATOR -> 0xa3
- Q_KEY_CODE_AC_HOME -> 0x97
And some mistakes corrected:
- Q_KEY_CODE_MENU was incorrectly mapped to the compose
scancode (0x8d) and is now 0x91
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20180117164118.8510-2-berrange@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
During Qemu guest migration, a destination process invokes ps2
post_load function. In that, if 'rptr' and 'count' values were
invalid, it could lead to OOB access or infinite loop issue.
Add check to avoid it.
Reported-by: Cyrille Chatras <cyrille.chatras@orange.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-id: 20171116075155.22378-1-ppandit@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
On Linux, a mouse event is generated for both down and up when mouse
wheel is used. This caused virtio_input_send() to be called twice each
time the wheel was used.
This commit adds a check for the button down state and only calls
virtio_input_send() when it is true.
Signed-off-by: Miika S <miika9764@gmail.com>
Message-Id: <20171222152531.1849-4-miika9764@gmail.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This was accidentally omitted from 77cb0f5aaf "Split adb.c into adb.c, adb-mouse.c
and adb-kbd.c".
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Replace all occurs of __FUNCTION__ except for the check in checkpatch
with the non GCC specific __func__.
One line in hcd-musb.c was manually tweaked to pass checkpatch.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
[THH: Removed hunks related to pxa2xx_mmci.c (fixed already)]
Signed-off-by: Thomas Huth <thuth@redhat.com>
It makes the code clearer to separate the bus implementation
from the devices one.
Replace ADB_DPRINTF() with trace events (and adding new ones in adb-kbd.c).
Some minor changes to make checkpatch.pl happy.
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20171220121406.24056-1-laurent@vivier.eu>
It's a x86-only device, so it does not make sense to keep it
in the shared misc folder.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
