HP-UX 11 and HP ODE tools use the "rsm 0,%reg" instruction in not priviledged
code paths to get the current PSW flags. The constant 0 means that no bits of
the PSW shall be reset, so this is effectively a read-only access to the PSW.
Allow this read-only access even for not privileged code.
Signed-off-by: Helge Deller <deller@gmx.de>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Linux writes zeroes at bootup into the default ports for LASI audio and
LASI floppy controller to reset those devices. Allow writing to those
registers to avoid HPMCs.
Signed-off-by: Helge Deller <deller@gmx.de>
Add the do_transaction_failed() handler to tigger a HPMC to the CPU
in case of I/O transaction errors.
This is a preparation commit.
We still lack implementation for some registers, so do not yet enable sending
HPMCs. Having this hunk here now nevertheless helps for the further
development, so that it can easily be enabled later on.
Signed-off-by: Helge Deller <deller@gmx.de>
Firmware and qemu reads and writes the MAC address for the LASI LAN via
registers in LASI. Allow those accesses and return zero even if LASI
LAN isn't enabled to avoid HPMCs (=crashes).
Signed-off-by: Helge Deller <deller@gmx.de>
The Astro/Elroy chip can work in either Hard-Fail or Soft-Fail mode.
Hard fail means the system bus will send an HPMC (=crash) to the
processor, soft fail means the system bus will ignore timeouts of
MMIO-reads or MMIO-writes and return -1ULL.
The HF mode is controlled by a bit in the status register and is usually
programmed by the OS. Return the corresponing values based on the current
value of that bit.
Signed-off-by: Helge Deller <deller@gmx.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Instead of stopping the emulation, report a MEMTX_DECODE_ERROR if the OS
tries to access non-existent registers.
Signed-off-by: Helge Deller <deller@gmx.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
For debugging purposes at the early stage of the bootup process,
the SeaBIOS-hppa firmware sometimes needs to output characters to the
serial console. Note that the serial console is the default output
method for parisc machines.
At this stage PCI busses and other devices haven't been initialized
yet. So, SeaBIOS-hppa will not be able to find the correct I/O ports
for the serial ports yet.
Instead, add an emulation for the "diag 0x101" opcode to assist here.
Without any other dependencies, SeaBIOS-hppa can then load the character
to be printed in register %r26 and issue the diag assembly instruction.
The qemu diag_console_output() helper function will then print
that character to the first serial port.
Signed-off-by: Helge Deller <deller@gmx.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Documentation of commands guest-ssh-get-authorized-keys,
guest-ssh-add-authorized-keys, and guest-ssh-remove-authorized-keys
describes the command's purpose after its arguments. Everywhere else,
we do it the other way round. Move it for consistency.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-ID: <20240129115008.674248-6-armbru@redhat.com>
Reviewed-by: Konstantin Kostiuk <kkostiuk@redhat.com>
Documentation of type BlockdevOptionsIscsi describes the type's
purpose after its members. Everywhere else, we do it the other way
round. Move it for consistency.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-ID: <20240129115008.674248-5-armbru@redhat.com>
Reviewed-by: Konstantin Kostiuk <kkostiuk@redhat.com>
Documentation of BlockExportRemoveMode has
Potential additional modes to be added in the future:
hide: Just hide export from new clients, leave existing connections
as is. Remove export after all clients are disconnected.
soft: Hide export from new clients, answer with ESHUTDOWN for all
further requests from existing clients.
I think this is useful only for developers. Elide it from generated
documentation by turning it into a TODO section.
This effectively reverts my own commit b71fd73cc4 (Revert "qapi:
BlockExportRemoveMode: move comments to TODO"). At the time, I was
about to elide TODO sections from the generated manual, I wasn't sure
about this one, and decided to avoid change. And now I've made up my
mind.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-ID: <20240129115008.674248-4-armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Documentation generated for dump-skeys contains
This command is only supported on s390 architecture.
and
If
~~
"TARGET_S390X"
The former became redundant in commit 901a34a400 (qapi: add 'If:'
section to generated documentation) added the latter. Drop the
former.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-ID: <20240129115008.674248-3-armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Documentation generated for SchemaInfo looks like
The members of "SchemaInfoBuiltin" when "meta-type" is ""builtin""
The members of "SchemaInfoEnum" when "meta-type" is ""enum""
The members of "SchemaInfoArray" when "meta-type" is ""array""
The members of "SchemaInfoObject" when "meta-type" is ""object""
The members of "SchemaInfoAlternate" when "meta-type" is ""alternate""
The members of "SchemaInfoCommand" when "meta-type" is ""command""
The members of "SchemaInfoEvent" when "meta-type" is ""event""
Additional members depend on the value of "meta-type".
The last line became redundant when commit 88f63467c5 (qapi2texi:
Generate reference to base type members) added the lines preceding it.
Drop it.
BlockdevOptions has the same issue. Drop
Remaining options are determined by the block driver.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-ID: <20240129115008.674248-2-armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Without this padding, an unwind through the signal handler
will pick up the unwind info for the preceding syscall.
This fixes gcc's 30_threads/thread/native_handle/cancel.cc.
Cc: qemu-stable@nongnu.org
Fixes: ee95fae075 ("linux-user/aarch64: Add vdso")
Resolves: https://linaro.atlassian.net/browse/GNU-974
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20240202034427.504686-1-richard.henderson@linaro.org>
These macros are no longer used.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20231103173841.33651-23-richard.henderson@linaro.org>
Represent each fcc field separately from the rest of fsr.
This vastly simplifies floating-point comparisons.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20231103173841.33651-22-richard.henderson@linaro.org>
Drop this field as a tcg global, loading it explicitly in the
few places required. This means that all FPop helpers may
once again be TCG_CALL_NO_WG.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20231103173841.33651-21-richard.henderson@linaro.org>
These two fields are adjusted by all FPop insns.
Having them separate makes it easier to set without masking.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20231103173841.33651-20-richard.henderson@linaro.org>
If an exception is to be raised, the destination fp register
should be unmodified. The current implementation is incorrect,
in that double results will be written back before calling
gen_helper_check_ieee_exceptions, despite the placement of
gen_store_fpr_D, since gen_dest_fpr_D returns cpu_fpr[].
We can simplify the entire implementation by having each
FPOp helper call check_ieee_exceptions. For the moment this
requires that all FPop helpers write to the TCG global cpu_fsr,
so remove TCG_CALL_NO_WG from the DEF_HELPER_FLAGS_*.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20231103173841.33651-19-richard.henderson@linaro.org>
Don't do the clearing explicitly before each FPop,
rather do it as part of the rest of exception handling.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20231103173841.33651-18-richard.henderson@linaro.org>
This field is read-only. It is easier to store it separately
and merge it only upon read.
While we're at it, use FSR_VER_SHIFT to initialize fpu_version.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20231103173841.33651-17-richard.henderson@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20231103173841.33651-16-richard.henderson@linaro.org>
These are no longer used for passing data to/from helpers.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20231103173841.33651-15-richard.henderson@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20231103173841.33651-14-richard.henderson@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20231103173841.33651-13-richard.henderson@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20231103173841.33651-12-richard.henderson@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20231103173841.33651-11-richard.henderson@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20231103173841.33651-10-richard.henderson@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20231103173841.33651-9-richard.henderson@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20231103173841.33651-8-richard.henderson@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20231103173841.33651-7-richard.henderson@linaro.org>
These are simple bit manipulation insns.
Begin using i128 for float128.
Implement FMOVq with do_qq.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20231103173841.33651-6-richard.henderson@linaro.org>
Use them for trans_FMOVq.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20231103173841.33651-5-richard.henderson@linaro.org>
Replace with tcg_temp_new_i32.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20231103173841.33651-4-richard.henderson@linaro.org>
Align the operation to the 32-byte cacheline.
Use 2 i128 instead of 4 i64.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20231103173841.33651-3-richard.henderson@linaro.org>
Align the operation to the 32-byte cacheline.
Use 2 pair of i128 instead of 8 pair of i32.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20231103173841.33651-2-richard.henderson@linaro.org>
Because there are more call clobbered registers than
call saved registers, we begin with all registers as
call clobbered and then reset those that are saved.
This was missed when we introduced the LSX support.
Cc: qemu-stable@nongnu.org
Fixes: 16288ded94 ("tcg/loongarch64: Lower basic tcg vec ops to LSX")
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2136
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20240201233414.500588-1-richard.henderson@linaro.org>
The `if not probe_proc_self_mem` check never passes, because
probe_proc_self_mem is a function object, which is a truthy value.
Add parentheses in order to perform a function call.
Fixes: dc84d50a7f9b ("tests/tcg: Add the PROT_NONE gdbstub test")
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Message-Id: <20240131220245.235993-1-iii@linux.ibm.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
For user-only mode, use MMU_USER_IDX.
For system mode, use CPUClass.mmu_index.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
