Move apic_get_bit(), apic_set_bit() to apic_internal.h, make the apic_get_ppr
symbol external. It's necessary to work with isr, tmr, irr and ppr outside
hw/intc/apic.c
Signed-off-by: Pavel Butsykin <pbutsykin@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Andreas Färber <afaerber@suse.de>
Message-Id: <1442927901-1084-2-git-send-email-den@openvz.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The arbitration register should read to the same value as the
IOAPIC id register. Fixes kvm-unit-tests ioapic.flat.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If a level-triggered interrupt goes down and back up before the
corresponding EOI, it should be coalesced. This fixes one testcase
in kvm-unit-tests' ioapic.flat.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This is the initial version of KVM-accelerated GICv3 support.
State load and save are not yet supported, live migration is
not possible.
In order to get correct class name in a simpler way, gicv3_class_name()
function is implemented, similar to gic_class_name().
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Ashok kumar <ashoks@broadcom.com>
Message-id: 69d8f01d14994d7a1a140e96aef59fd332d02293.1441784344.git.p.fedin@samsung.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some functions previously used only by vGICv2 are useful also for vGICv3
implementation. Untie them from GICState and make accessible from within
other modules:
- kvm_arm_gic_set_irq()
- kvm_gic_supports_attr() - moved to common code and renamed to
kvm_device_check_attr()
- kvm_gic_access() - turned into GIC-independent kvm_device_access().
Data pointer changed to void * because some GICv3 registers are
64-bit wide
Some of these changes are not used right now, but they will be helpful for
implementing live migration.
Actually kvm_dist_get() and kvm_dist_put() could also be made reusable, but
they would require two extra parameters (s->dev_fd and s->num_cpu) as well as
lots of typecasts of 's' to DeviceState * and back to GICState *. This makes
the code very ugly so i decided to stop at this point. I tried also an
approach with making a base class for all possible GICs, but it would contain
only three variables (dev_fd, cpu_num and irq_num), and accessing them through
the rest of the code would be again tedious (either ugly casts or qemu-style
separate object pointer). So i disliked it too.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Tested-by: Ashok kumar <ashoks@broadcom.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 2ef56d1dd64ffb75ed02a10dcdaf605e5b8ff4f8.1441784344.git.p.fedin@samsung.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This class is to be used by both software and KVM implementations of GICv3
Currently it is mostly a placeholder, but in future it is supposed to hold
qemu's representation of GICv3 state, which is necessary for migration.
The interface of this class is fully compatible with GICv2 one. This is
done in order to simplify integration with existing code.
Signed-off-by: Shlomo Pongratz <shlomo.pongratz@huawei.com>
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Reviewed-by: Eric Auger <eric.auger@linaro.org>
Tested-by: Ashok kumar <ashoks@broadcom.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: aff8baaee493cdcab0694b4a1d4dd5ff27c37ed2.1441784344.git.p.fedin@samsung.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
A number of source files have statements accidentally
terminated by a double semicolon - eg 'foo = bar;;'.
This is harmless but a mistake none the less.
The tcg/ia64/tcg-target.c file is whitelisted because
it has valid use of ';;' in a comment containing assembly
code.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
If we directly boot a kernel in NonSecure on a system where the GIC
supports the security extensions then we must cause the GIC to
configure its interrupts into group 1 (NonSecure) rather than the
usual group 0, and with their initial priority set to the highest
NonSecure priority rather than the usual highest Secure priority.
Otherwise the guest kernel will be unable to use any interrupts.
Implement this behaviour, controlled by a flag which we set if
appropriate when the ARM bootloader code calls our ARMLinuxBootIf
interface callback.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1441383782-24378-4-git-send-email-peter.maydell@linaro.org
Although we were correctly handling interrupts becoming active
and then inactive, we weren't actually exposing this to the guest
by setting the 'active' flag for the interrupt, so reads
of GICD_ICACTIVERn and GICD_ISACTIVERn would generally incorrectly
return zeroes. Correct this oversight.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1438089748-5528-6-git-send-email-peter.maydell@linaro.org
The running_irq and last_active arrays represent state which
doesn't exist in a real hardware GIC. The only thing we use
them for is updating the running priority when an interrupt
is completed, but in fact we can use the active-priority
registers to do this. The running priority is always the
priority corresponding to the lowest set bit in the active
priority registers, because only one interrupt at any
particular priority can be active at once.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1438089748-5528-5-git-send-email-peter.maydell@linaro.org
A GICv2 has both GICC_APR<n> and GICC_NSAPR<n> registers, with
the latter holding the active priority bits for Group 1 interrupts
(usually Nonsecure interrupts), and the Nonsecure view of the
GICC_APR<n> is the second half of the GICC_NSAPR<n> registers.
Turn our half-hearted implementation of APR<n> into a proper
implementation of both APR<n> and NSAPR<n>:
* Add the underlying state for NSAPR<n>
* Make sure APR<n> aren't visible for pre-GICv2
* Implement reading of NSAPR<n>
* Make non-secure reads of APR<n> behave correctly
* Implement writing to APR<n> and NSAPR<n>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1438089748-5528-4-git-send-email-peter.maydell@linaro.org
Priority values for the GIC are divided into a "group priority"
and a "subpriority" (with the division being determined by the
binary point register). The running priority is only determined
by the group priority of the active interrupts, not the
subpriority. In particular, this means that there can't be more
than one active interrupt at any particular group priority.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1438089748-5528-3-git-send-email-peter.maydell@linaro.org
Change the implementation of the Interrupt Control and State Register
in the v7M NVIC to not use the running_irq and last_active internal
state fields in the GIC. These fields don't correspond to state in
a real GIC and will be removed soon.
The changes to the ICSR are:
* the VECTACTIVE field is documented as identical to the IPSR[8:0]
field, so implement it that way
* implement RETTOBASE via looking at the active state bits
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1438089748-5528-2-git-send-email-peter.maydell@linaro.org
When we add new adapter routes we call kvm_irqchip_add_route() for every
virtqueue and in the same step also do the KVM_SET_GSI_ROUTING ioctl.
This is unnecessary costly as the interface allows us to set multiple
routes in one go. Let's first add all routes to the table stored in the
global kvm_state and then do the ioctl to commit the routes to the
in-kernel irqchip.
This saves us several ioctls to the kernel where for each call a list
is reallocated and populated.
Signed-off-by: Jens Freimann <jfrei@linux.vnet.ibm.com>
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Extracted duplicated initialization code from SW-emulated and KVM GIC
implementations and put into gic_init_irqs_and_mmio()
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Message-id: 8ea5b2781ef39cb5989420987fc73c70e377687d.1438758065.git.p.fedin@samsung.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When supporting CPU hot removal by parking the vCPU fd and reusing
it during hotplug again, there can be cases where we try to reenable
KVM_CAP_IRQ_XICS CAP for the vCPU for which it was already enabled.
Introduce a boolean member in ICPState to track this and don't
reenable the CAP if it was already enabled earlier.
Re-enabling this CAP should ideally work, but currently it results in
kernel trying to create and associate ICP with this vCPU and that
fails since there is already an ICP associated with it. Hence this
patch is needed to work around this problem in the kernel.
This change allows CPU hot removal to work for sPAPR.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
The code for -machine pseries maintains a global sPAPREnvironment structure
which keeps track of general state information about the guest platform.
This predates the existence of the MachineState structure, but performs
basically the same function.
Now that we have the generic MachineState, fold sPAPREnvironment into
sPAPRMachineState, the pseries specific subclass of MachineState.
This is mostly a matter of search and replace, although a few places which
relied on the global spapr variable are changed to find the structure via
qdev_get_machine().
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
The arm_gic_kvm now calls kvm_irqchip_set_qemuirq_gsi to build
the hash table storing qemu_irq/gsi mappings. From that point on
irqfd can be setup directly from the qemu_irq using
kvm_irqchip_add_irqfd_notifier.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Tested-by: Vikram Sethi <vikrams@codeaurora.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The arm_gic_common reset function was missing reset code for
several of the GIC's state fields:
* bpr[]
* abpr[]
* priority1[]
* priority2[]
* sgi_pending[]
* irq_target[] (SMP configurations only)
These probably went unnoticed because most guests will either
never touch them, or will write to them in the process of
configuring the GIC before enabling interrupts.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1435602345-32210-1-git-send-email-peter.maydell@linaro.org
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
These macros expand into error class enumeration constant, comma,
string. Unclean. Has been that way since commit 13f59ae.
The error class is always ERROR_CLASS_GENERIC_ERROR since the previous
commit.
Clean up as follows:
* Prepend every use of a QERR_ macro by ERROR_CLASS_GENERIC_ERROR, and
delete it from the QERR_ macro. No change after preprocessing.
* Rewrite error_set(ERROR_CLASS_GENERIC_ERROR, ...) into
error_setg(...). Again, no change after preprocessing.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
This patch fixes so that gic_update always updates all the cores with
new pending irq states. If the function returns early it is possible
to get interrupts that has already been acknowledged.
Signed-off-by: Johan Karlsson <johan.karlsson@enea.com>
[PMM: rebased to apply to current master]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We create optional sections with this patch. But we already have
optional subsections. Instead of having two mechanism that do the
same, we can just generalize it.
For subsections we just change:
- Add a needed function to VMStateDescription
- Remove VMStateSubsection (after removal of the needed function
it is just a VMStateDescription)
- Adjust the whole tree, moving the needed function to the corresponding
VMStateDescription
Signed-off-by: Juan Quintela <quintela@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVbvwjAAoJEL7lnXSkw9fbaFwIAIh6PN5v6fvuEjnPX5ijHZC2
7iJoFd0I2cYrxgLe4xONFX9qzV5vgdEAJfXCljVCKAmzu5RK7G0ZSW81sJ3t6Mp8
kA8buJeyTp2UcTlDrC3qji8ScEIj+g8I9tKGflNVI2uDAVumMBPqnJNSFhbaqYlu
SEq+4y/D3J6xPzr7NhyHliG0NmxJrIn6QCtux5djj3xO4KXfp1j2YQCPKhYjkRlW
wHfqeD7x9LX6875FX3csgfPsYIycW0WYtba2adTe0vbTsclOY0CU3ho8HPeXgHE6
WQj6KYGT8Fo0zmK8UV0Jmok7+hZoxXXInf6vY+sSY58oe71FgdxNwLvIC6N0eQc=
=AALk
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mjt/tags/pull-trivial-patches-2015-06-03' into staging
trivial patches for 2015-06-03
# gpg: Signature made Wed Jun 3 14:07:47 2015 BST using RSA key ID A4C3D7DB
# gpg: Good signature from "Michael Tokarev <mjt@tls.msk.ru>"
# gpg: aka "Michael Tokarev <mjt@corpit.ru>"
# gpg: aka "Michael Tokarev <mjt@debian.org>"
* remotes/mjt/tags/pull-trivial-patches-2015-06-03: (30 commits)
configure: postfix --extra-cflags to QEMU_CFLAGS
cadence_gem: Fix Rx buffer size field mask
slirp: use less predictable directory name in /tmp for smb config (CVE-2015-4037)
translate-all: delete prototype for non-existent function
Add -incoming help text
hw/display/tc6393xb.c: Fix misusing qemu_allocate_irqs for single irq
hw/arm/nseries.c: Fix misusing qemu_allocate_irqs for single irq
hw/alpha/typhoon.c: Fix misusing qemu_allocate_irqs for single irq
hw/unicore32/puv3.c: Fix misusing qemu_allocate_irqs for single irq
hw/lm32/milkymist.c: Fix misusing qemu_allocate_irqs for single irq
hw/lm32/lm32_boards.c: Fix misusing qemu_allocate_irqs for single irq
hw/ppc/prep.c: Fix misusing qemu_allocate_irqs for single irq
hw/sparc/sun4m.c: Fix misusing qemu_allocate_irqs for single irq
hw/timer/arm_timer.c: Fix misusing qemu_allocate_irqs for single irq
hw/isa/i82378.c: Fix misusing qemu_allocate_irqs for single irq
hw/isa/lpc_ich9.c: Fix misusing qemu_allocate_irqs for single irq
hw/i386/pc: Fix misusing qemu_allocate_irqs for single irq
hw/intc/exynos4210_gic.c: Fix memory leak by adjusting order
hw/arm/omap_sx1.c: Fix memory leak spotted by valgrind
hw/ppc/e500.c: Fix memory leak
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=VKFL
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/ehabkost/tags/x86-pull-request' into staging
X86 queue 2015-06-02
# gpg: Signature made Tue Jun 2 20:21:17 2015 BST using RSA key ID 984DC5A6
# gpg: Good signature from "Eduardo Habkost <ehabkost@redhat.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 5A32 2FD5 ABC4 D3DB ACCF D1AA 2807 936F 984D C5A6
* remotes/ehabkost/tags/x86-pull-request:
arch_init: Drop target-x86_64.conf
target-i386: Register QOM properties for feature flags
apic: convert ->busdev.qdev casts to C casts
target-i386: Fix signedness of MSR_IA32_APICBASE_BASE
pc: Ensure non-zero CPU ref count after attaching to ICC bus
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use C casts to avoid accessing ICCDevice's qdev field
directly.
Signed-off-by: Zhu Guihua <zhugh.fnst@cn.fujitsu.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Acked-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
After introduction of kvm_arch_msi_data_to_gsi, kvm_gsi_direct_mapping
now can be set on ARM. Also kvm_msi_via_irqfd_allowed can be set,
depending on kernel irqfd support, hence enabling VIRTIO-PCI with
vhost back-end.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The ARM GICv2m widget is a little device that handles MSI interrupt
writes to a trigger register and ties them to a range of interrupt lines
wires to the GIC. It has a few status/id registers and the interrupt wires,
and that's about it.
A board instantiates the device by setting the base SPI number and
number SPIs for the frame. The base-spi parameter is indexed in the SPI
number space only, so base-spi == 0, means IRQ number 32. When a device
(the PCI host controller) writes to the trigger register, the payload is
the GIC IRQ number, so we have to subtract 32 from that and then index
into our frame of SPIs.
When instantiating a GICv2m device, tell PCI that we have instantiated
something that can deal with MSIs. We rely on the board actually wiring
up the GICv2m to the PCI host controller.
Reviewed-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Message-id: 1432897270-7780-3-git-send-email-christoffer.dall@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add support to gic_update() for determining the current IRQ
and FIQ status when interrupt grouping is supported. This
simply requires that instead of always raising IRQ we
check the group of the highest priority pending interrupt
and the GICC_CTLR.FIQEn bit to see whether we should raise
IRQ or FIQ.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1430502643-25909-15-git-send-email-peter.maydell@linaro.org
Grouping (GICv2) and Security Extensions change the behavior of IAR
reads. Acknowledging Group0 interrupts is only allowed from Secure
state and acknowledging Group1 interrupts from Secure state is only
allowed if AckCtl bit is set.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1430502643-25909-14-git-send-email-peter.maydell@linaro.org
Message-id: 1429113742-8371-14-git-send-email-greg.bellows@linaro.org
[PMM: simplify significantly by reusing the existing
gic_get_current_pending_irq() rather than reimplementing the
same logic here]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Grouping (GICv2) and Security Extensions change the behavior of EOIR
writes. Completing Group0 interrupts is only allowed from Secure state.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1430502643-25909-13-git-send-email-peter.maydell@linaro.org
Message-id: 1429113742-8371-13-git-send-email-greg.bellows@linaro.org
[PMM: Rather than go to great lengths to ignore the UNPREDICTABLE case
of a Secure EOI of a Group1 (NS) irq with AckCtl == 0, we just let
it fall through; add a comment about it.]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Grouping (GICv2) and Security Extensions change the behaviour of reads
of the highest priority pending interrupt register (ICCHPIR/GICC_HPPIR).
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1430502643-25909-12-git-send-email-peter.maydell@linaro.org
Message-id: 1429113742-8371-12-git-send-email-greg.bellows@linaro.org
[PMM: make utility fn static; coding style fixes; AckCtl has an effect
for GICv2 without security extensions as well; removed checks on enable
bits because these are done when we set current_pending[cpu]]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
GICs with Security Extensions restrict the non-secure view of the
interrupt priority and priority mask registers.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1430502643-25909-11-git-send-email-peter.maydell@linaro.org
Message-id: 1429113742-8371-15-git-send-email-greg.bellows@linaro.org
[PMM: minor code tweaks; fixed missing masking in gic_set_priority_mask
and gic_set_priority]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
For GICs with Security Extensions Non-secure reads have a restricted
view on the current running priority.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1430502643-25909-10-git-send-email-peter.maydell@linaro.org
Message-id: 1429113742-8371-11-git-send-email-greg.bellows@linaro.org
[PMM: make function static, minor comment tweak]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
ICCICR/GICC_CTLR is banked in GICv1 implementations with Security
Extensions or in GICv2 in independent from Security Extensions.
This makes it possible to enable forwarding of interrupts from
the CPU interfaces to the connected processors for Group0 and Group1.
We also allow to set additional bits like AckCtl and FIQEn by changing
the type from bool to uint32. Since the field does not only store the
enable bit anymore and since we are touching the vmstate, we use the
opportunity to rename the field to cpu_ctlr.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1430502643-25909-9-git-send-email-peter.maydell@linaro.org
Message-id: 1429113742-8371-9-git-send-email-greg.bellows@linaro.org
[PMM: rewrote to store state in a single uint32_t rather than
keeping the NS and S banked variants separate; this considerably
simplifies the get/set functions]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This register is banked in GICs with Security Extensions. Storing the
non-secure copy of BPR in the abpr, which is an alias to the non-secure
copy for secure access. ABPR itself is only accessible from secure state
if the GIC implements Security Extensions.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1430502643-25909-8-git-send-email-peter.maydell@linaro.org
Message-id: 1429113742-8371-10-git-send-email-greg.bellows@linaro.org
[PMM: rewrote to fix style issues and correct handling of GICv2
without security extensions]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
ICDDCR/GICD_CTLR is banked if the GIC has the security extensions,
and the S (or only) copy has separate enable bits for Group0 and
Group1 enable if the GIC implements interrupt groups.
EnableGroup0 (Bit [1]) in GICv1 is architecturally IMPDEF. Since this
bit (Enable Non-secure) is present in the integrated GIC of the Cortex-A9
MPCore, we support this bit in our GICv1 implementation too.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1430502643-25909-7-git-send-email-peter.maydell@linaro.org
Message-id: 1429113742-8371-8-git-send-email-greg.bellows@linaro.org
[PMM: rewritten to store the state in a single s->ctlr uint32,
with the NS register handled as an alias of bit 1 in that value;
added vmstate version bump]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Now that the GIC base class has state fields for the GICD_IGROUPRn
registers, make kvm_arm_gic_get() and kvm_arm_gic_put() write and
read them. This allows us to remove the check that made us
fail migration if the guest had set any of the group register bits.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1430502643-25909-6-git-send-email-peter.maydell@linaro.org
The Interrupt Group Registers allow the guest to configure interrupts
into one of two groups, where Group0 are higher priority and may
be routed to IRQ or FIQ, and Group1 are lower priority and always
routed to IRQ. (In a GIC with the security extensions Group0 is
Secure interrupts and Group 1 is NonSecure.)
The GICv2 always supports interrupt grouping; the GICv1 does only
if it implements the security extensions.
This patch implements the ability to read and write the registers;
the actual functionality the bits control will be added in a
subsequent patch.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1430502643-25909-5-git-send-email-peter.maydell@linaro.org
Message-id: 1429113742-8371-7-git-send-email-greg.bellows@linaro.org
[PMM: bring GIC_*_GROUP macros into line with the others, ie a
simple SET/CLEAR/TEST rather than GROUP0/GROUP1;
utility gic_has_groups() function;
minor style fixes;
bump vmstate version]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Switch the GIC's MMIO callback functions to the read_with_attrs
and write_with_attrs functions which provide MemTxAttrs. This will
allow the GIC to correctly handle secure and nonsecure register
accesses.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1430502643-25909-4-git-send-email-peter.maydell@linaro.org
Add a QOM property which allows the GIC Security Extensions to be
enabled. These are an optional part of the GICv1 and GICv2 architecture.
This commit just adds the property and some sanity checks that it
is only enabled on GIC revisions that support it.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1430502643-25909-3-git-send-email-peter.maydell@linaro.org
Message-id: 1429113742-8371-5-git-send-email-greg.bellows@linaro.org
[PMM: changed property name, added checks that it isn't set for
older GIC revisions or if using the KVM VGIC; reworded commit message]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Create the outbound FIQ lines from the GIC to the CPUs; these are
used if the GIC has security extensions or grouping support.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1430502643-25909-2-git-send-email-peter.maydell@linaro.org
Message-id: 1429113742-8371-2-git-send-email-greg.bellows@linaro.org
[PMM: added FIQ lines to kvm-arm-gic so its interface is the same;
tweaked commit message]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Consider the following pseudo code to configure SYSTICK (The
recommended programming sequence from "the definitive guide to the
arm cortex-m3"):
SYSTICK Reload Value Register = 0xffff
SYSTICK Current Value Register = 0
SYSTICK Control and Status Register = 0x7
The pseudo code "SYSTICK Current Value Register = 0" leads to invoking
systick_reload(). As a consequence, the systick.tick member is updated
and the systick timer starts to count down when the ENABLE bit of
SYSTICK Control and Status Register is cleared.
The worst case is that: during the system initialization, the reset
value of the SYSTICK Control and Status Register is 0x00000000.
When the code "SYSTICK Current Value Register = 0" is executed, the
systick.tick member is accumulated with "(s->systick.reload + 1) *
systick_scale(s)". The systick_scale() gets the external_ref_clock
scale because the CLKSOURCE bit of the SYSTICK Control and Status
Register is cleared. This is the incorrect behavior because of the
code "SYSTICK Control and Status Register = 0x7". Actually, we want
the processor clock instead of the external reference clock.
This incorrect behavior defers the generation of the first interrupt.
The patch fixes the above-mentioned issue by setting the systick.tick
member and modifying the systick timer only if the ENABLE bit of
the SYSTICK Control and Status Register is set.
In addition, the Cortex-M3 Devices Generic User Guide mentioned that
"When ENABLE is set to 1, the counter loads the RELOAD value from the
SYST RVR register and then counts down". This patch adheres to the
statement of the user guide.
Signed-off-by: Adrian Huang <adrianhuang0701@gmail.com>
Reviewed-by: Jim Huang <jserv.tw@gmail.com>
[PMM: minor tweak to comment text]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Replace call of cpu_is_bsp(s->cpu) which really returns
!!(s->apicbase & MSR_IA32_APICBASE_BSP)
with directly collected value. Due to this the tracepoint
trace_cpu_get_apic_base((uint64_t)s->apicbase);
will not be hit anymore in apic_reset_common.
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Andreas Färber <afaerber@suse.de>
CC: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1428414832-3104-1-git-send-email-den@openvz.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- next part in the thread-safe address_space_* saga: atomic access
to the bounce buffer and the map_clients list, from Fam
- optional support for linking with tcmalloc, also from Fam
- reapplying Peter Crosthwaite's "Respect as_translate_internal
length clamp" after fixing the SPARC fallout.
- build system fix from Wei Liu
- small acpi-build and ioport cleanup by myself
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJVQJd4AAoJEL/70l94x66DYFYH/3ifhqWZsd4dfJri0CGAHI4i
SpPmNeouc8W+F/3lwf6Inrh5NnTgd5QzoUBMQaWVkQKwUiWls8g2mXkT3jo0iDqT
/B40YXnZjNm20MixNaZmk9AsOF6OqPM8EMufau874k5zTlx3tCGAW1QD+I1N7WK7
DfsFsIUD1svo2prn55fSoitMG1TIVPnpcklb4YGJRbAacQYUDhr5KAIhT1quDR2R
93BvToyQmPqRQ4YKqnJLp8HAkL4FaJumfFZVvyh2cZvyaYGN/RVdi2Dw985dJDPX
/z4enE4GCAs4RDw3lZ1RDbiZDqpT2ibFgASg/arX3SxzqHirOGvMdkOjO99r9j4=
=aLjh
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging
- miscellaneous cleanups for TCG (Emilio) and NBD (Bogdan)
- next part in the thread-safe address_space_* saga: atomic access
to the bounce buffer and the map_clients list, from Fam
- optional support for linking with tcmalloc, also from Fam
- reapplying Peter Crosthwaite's "Respect as_translate_internal
length clamp" after fixing the SPARC fallout.
- build system fix from Wei Liu
- small acpi-build and ioport cleanup by myself
# gpg: Signature made Wed Apr 29 09:34:00 2015 BST using RSA key ID 78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>"
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* remotes/bonzini/tags/for-upstream: (22 commits)
nbd/trivial: fix type cast for ioctl
translate-all: use bitmap helpers for PageDesc's bitmap
target-i386: disable LINT0 after reset
Makefile.target: prepend $libs_softmmu to $LIBS
milkymist: do not modify libs-softmmu
configure: Add support for tcmalloc
exec: Respect as_translate_internal length clamp
ioport: reserve the whole range of an I/O port in the AddressSpace
ioport: loosen assertions on emulation of 16-bit ports
ioport: remove wrong comment
ide: there is only one data port
gus: clean up MemoryRegionPortio
sb16: remove useless mixer_write_indexw
sun4m: fix slavio sysctrl and led register sizes
acpi-build: remove dependency from ram_addr.h
memory: add memory_region_ram_resize
dma-helpers: Fix race condition of continue_after_map_failure and dma_aio_cancel
exec: Notify cpu_register_map_client caller if the bounce buffer is available
exec: Protect map_client_list with mutex
linux-user, bsd-user: Remove two calls to cpu_exec_init_all
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Due to old Seabios bug, QEMU reenable LINT0 after reset. This bug is long gone
and therefore this hack is no longer needed. Since it violates the
specifications, it is removed.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Message-Id: <1428881529-29459-2-git-send-email-namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Rewrite the loop using level &= level - 1 to clear the least significant
bit after each iteration. This simplifies the loop and makes it easy to
replace ffs(3) with ctz32().
Cc: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1427124571-28598-8-git-send-email-stefanha@redhat.com
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
