Commit Graph

28129 Commits

Author SHA1 Message Date
Paolo Bonzini b2f73a0784 sev/i386: Allow AP booting under SEV-ES
When SEV-ES is enabled, it is not possible modify the guests register
state after it has been initially created, encrypted and measured.

Normally, an INIT-SIPI-SIPI request is used to boot the AP. However, the
hypervisor cannot emulate this because it cannot update the AP register
state. For the very first boot by an AP, the reset vector CS segment
value and the EIP value must be programmed before the register has been
encrypted and measured. Search the guest firmware for the guest for a
specific GUID that tells Qemu the value of the reset vector to use.

Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Cc: Richard Henderson <richard.henderson@linaro.org>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Message-Id: <22db2bfb4d6551aed661a9ae95b4fdbef613ca21.1611682609.git.thomas.lendacky@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2021-02-16 17:15:39 +01:00
James Bottomley 9617cddb72 pc: add parser for OVMF reset block
OVMF is developing a mechanism for depositing a GUIDed table just
below the known location of the reset vector.  The table goes
backwards in memory so all entries are of the form

<data>|len|<GUID>

Where <data> is arbtrary size and type, <len> is a uint16_t and
describes the entire length of the entry from the beginning of the
data to the end of the guid.

The foot of the table is of this form and <len> for this case
describes the entire size of the table.  The table foot GUID is
defined by OVMF as 96b582de-1fb2-45f7-baea-a366c55a082d and if the
table is present this GUID is just below the reset vector, 48 bytes
before the end of the firmware file.

Add a parser for the ovmf reset block which takes a copy of the block,
if the table foot guid is found, minus the footer and a function for
later traversal to return the data area of any specified GUIDs.

Signed-off-by: James Bottomley <jejb@linux.ibm.com>

Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20210204193939.16617-2-jejb@linux.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2021-02-16 17:15:39 +01:00
Roger Pau Monne 7f22201ac8 xen-block: fix reporting of discard feature
Linux blkfront expects both "discard-granularity" and
"discard-alignment" present on xenbus in order to properly enable the
feature, not exposing "discard-alignment" left some Linux blkfront
versions with a broken discard setup. This has also been addressed in
Linux with:

https://lore.kernel.org/lkml/20210118151528.81668-1-roger.pau@citrix.com/T/#u

Fix QEMU to report a "discard-alignment" of 0, in order for it to work
with older Linux frontends.

Reported-by: Arthur Borsboom <arthurborsboom@gmail.com>
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Message-Id: <20210118153330.82324-1-roger.pau@citrix.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2021-02-15 15:10:14 +01:00
Alexander Bulekov 26941eb4ca hw/ide/ahci: map cmd_fis as DMA_DIRECTION_TO_DEVICE
cmd_fis is mapped as DMA_DIRECTION_FROM_DEVICE, however, it is read
from, and not written to anywhere. Fix the DMA_DIRECTION and mark
cmd_fis as read-only in the code.

Signed-off-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20210119164051.89268-1-alxndr@bu.edu>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2021-02-15 15:10:14 +01:00
Peter Maydell f4ceebdec5 Pull request m68k-20210212
Move bootinfo headers to include/standard-headers/asm-m68k
 Add M68K_FEATURE_MSP, M68K_FEATURE_MOVEC, M68K_FEATURE_M68010
 Add 68060 CR BUSCR and PCR (unimplemented)
 CPU types and features cleanup
 -----BEGIN PGP SIGNATURE-----
 
 iQJGBAABCAAwFiEEzS913cjjpNwuT1Fz8ww4vT8vvjwFAmAm77QSHGxhdXJlbnRA
 dml2aWVyLmV1AAoJEPMMOL0/L748RCUP/2OzWc0B+q7p8JClOhzFALhz0GgiH0z9
 r+OWTsyFJRK17zmqeL88w6RdLPaU0VJOoOu/tgBFLy0UtQfLaxuetbM1KCsMQyiM
 hq5ZG5Syi+Vb4bFfwk3b6skibEkdhwcRPXSNRtCdkSbqqvwLAJYHqjtwwEmBZDhe
 9ZsjE+VMAbBRSMJfj4K9Vyter9iBxiZnJB71sJsEKy2WRKJjMSvQaLTBV1ocTL+p
 UNROsUNK0O4G/0hOLxgAy5Azb6z+A9ln67RsaseCWgRkMERf7DZb2XpDOrKB1gau
 g6KFweInDw2s4kabg+30Oyh8yQVw7o89Atg8d57Kgub7GDJTReUtJVtc+X3CXdIv
 630k1kDsx7h5prZJ8aTPZQXkjfOcJiritzb+Ivb0DtDz/hM6QDKtgZ8OHWJ7/ZTp
 x8RGIZzFaHmV+6nMTRQlUmZyjfmyPEpGpIRiY+IHyogZ7b1MOInIKboC4Ewq4KgS
 SdscFT8uiT8F3EdfFvIkBYbV04JNL/JILgEv9fmLsdvBDSXY5DF1Tv6qiG2yJkH3
 d4w9FaFtZpQdFiU95TBJ048imjda6JlxCdAOA3wCT5GrVNd3yEZMbR7ATS8dcxw5
 cPRTidnKSC9ScUzyRlyPg00/u0hAwrcL20cCt7HYN3duNk1CZCdtbdTS8urIkKy6
 SqoBn0pUdtsU
 =RnpD
 -----END PGP SIGNATURE-----

Merge remote-tracking branch 'remotes/vivier/tags/m68k-for-6.0-pull-request' into staging

Pull request m68k-20210212

Move bootinfo headers to include/standard-headers/asm-m68k
Add M68K_FEATURE_MSP, M68K_FEATURE_MOVEC, M68K_FEATURE_M68010
Add 68060 CR BUSCR and PCR (unimplemented)
CPU types and features cleanup

# gpg: Signature made Fri 12 Feb 2021 21:14:28 GMT
# gpg:                using RSA key CD2F75DDC8E3A4DC2E4F5173F30C38BD3F2FBE3C
# gpg:                issuer "laurent@vivier.eu"
# gpg: Good signature from "Laurent Vivier <lvivier@redhat.com>" [full]
# gpg:                 aka "Laurent Vivier <laurent@vivier.eu>" [full]
# gpg:                 aka "Laurent Vivier (Red Hat) <lvivier@redhat.com>" [full]
# Primary key fingerprint: CD2F 75DD C8E3 A4DC 2E4F  5173 F30C 38BD 3F2F BE3C

* remotes/vivier/tags/m68k-for-6.0-pull-request:
  m68k: import bootinfo headers from linux
  m68k: add MSP detection support for stack pointer swap helpers
  m68k: MOVEC insn. should generate exception if wrong CR is accessed
  m68k: add missing BUSCR/PCR CR defines, and BUSCR/PCR/CAAR CR to m68k_move_to/from
  m68k: improve comments on m68k_move_to/from helpers
  m68k: cascade m68k_features by m680xx_cpu_initfn() to improve readability
  m68k: improve cpu instantiation comments

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2021-02-13 18:16:43 +00:00
Laurent Vivier 382d71af7d m68k: import bootinfo headers from linux
Copy bootinfo.h and bootinfo-mac.h from arch/m68k/include/uapi/asm/
to include/standard-headers/asm-m68k/

Imported from linux v5.9 but didn't change since v4.14 (header update)
and since v4.10 (content update).

Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20201220112615.933036-2-laurent@vivier.eu>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
2021-02-11 21:56:42 +01:00
Peter Maydell eac92d3163 target-arm queue:
* Correctly initialize MDCR_EL2.HPMN
  * versal: Use nr_apu_cpus in favor of hard coding 2
  * accel/tcg: Add URL of clang bug to comment about our workaround
  * Add support for FEAT_DIT, Data Independent Timing
  * Remove GPIO from unimplemented NPCM7XX
  * Fix SCR RES1 handling
  * Don't migrate CPUARMState.features
 -----BEGIN PGP SIGNATURE-----
 
 iQJNBAABCAA3FiEE4aXFk81BneKOgxXPPCUl7RQ2DN4FAmAli/gZHHBldGVyLm1h
 eWRlbGxAbGluYXJvLm9yZwAKCRA8JSXtFDYM3jarEACMMPvwnWYxY3m/aDMHmgoV
 jTjdyutBKSqIDPXPZNIDIonutsaE521MdGjSAsMtoSBN4C30qd4HX3gqEitVGVSF
 KlF9MWbLMbe6UQUU5NfRfbFKwCazHqNiAffO45677LiJHH9v2q1sAsUW/KTNGpAv
 PDOSNfpkIUeYfZapv+dIs1rkjEKPHo1/M/KvJGSkIi0DKQeJKjKAB4rP+Fwf+iBu
 XH0mXrUqO348u+LOl4hhCRzRzZ6FKwv40IqrtB1WBqCmfdASX7MtD4GPh5rwC63C
 8gkq1Zb3xUIQA2oCppT8UBq4+D/gBgDjGCg0irC6/SL1+N4ThAZxdz/evCbowLip
 27B1ANfxgmQF1tLXYXIWfoyrBt97pHFH6Koh/xdnbiznNNkL8TnuC6mTe+9xCp2m
 UGolv/7Lgb5mtXwjyHesR/LxQugzC38kUcAzbDw9zIT8C9l19K4/u9UXBlyDZ0WE
 l9aGRWulk9EtJ05biPSUbuHZROPg0KiupfgbjF2jVwW3ehMNYC/CYHhWLrnt4g8m
 Dx2+ZioAMUmAgyzmcc6kgLzyoEbUsja5c6JQKTkaxsdJiyvH3hN2msvCH3uEgqVp
 J6h01HaIE7Fv2WwXNKqbqG4d47I1ryOymCPQ99h2wJzbDIJWV8Tbp3JcqJCDqzp3
 Us8I+DB40vE+3WbVQ9lvlw==
 =3Ptb
 -----END PGP SIGNATURE-----

Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20210211-1' into staging

target-arm queue:
 * Correctly initialize MDCR_EL2.HPMN
 * versal: Use nr_apu_cpus in favor of hard coding 2
 * accel/tcg: Add URL of clang bug to comment about our workaround
 * Add support for FEAT_DIT, Data Independent Timing
 * Remove GPIO from unimplemented NPCM7XX
 * Fix SCR RES1 handling
 * Don't migrate CPUARMState.features

# gpg: Signature made Thu 11 Feb 2021 19:56:40 GMT
# gpg:                using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg:                issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [ultimate]
# gpg:                 aka "Peter Maydell <pmaydell@gmail.com>" [ultimate]
# gpg:                 aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [ultimate]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83  15CF 3C25 25ED 1436 0CDE

* remotes/pmaydell/tags/pull-target-arm-20210211-1:
  target/arm: Correctly initialize MDCR_EL2.HPMN
  hw/arm: versal: Use nr_apu_cpus in favor of hard coding 2
  accel/tcg: Add URL of clang bug to comment about our workaround
  arm: Update infocenter.arm.com URLs
  target/arm: Set ID_PFR0.DIT to 1 for "max" 32-bit CPU
  target/arm: Set ID_AA64PFR0.DIT and ID_PFR0.DIT to 1 for "max" AA64 CPU
  target/arm: Support AA32 DIT by moving PSTATE_SS from cpsr into env->pstate
  target/arm: Add support for FEAT_DIT, Data Independent Timing
  hw/arm: Remove GPIO from unimplemented NPCM7XX
  target/arm: Fix SCR RES1 handling
  target/arm: Don't migrate CPUARMState.features

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2021-02-11 19:57:50 +00:00
Edgar E. Iglesias 4565d82616 hw/arm: versal: Use nr_apu_cpus in favor of hard coding 2
Use nr_apu_cpus in favor of hard coding 2.

Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-id: 20210210142048.3125878-2-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2021-02-11 19:48:09 +00:00
Klaus Jensen 832a59e43b hw/block/nvme: fix error handling in nvme_ns_realize
nvme_ns_realize passes errp to nvme_register_namespaces, but then try to
prepend errp with local_err.

Just remove the local_err and use errp directly.

Fixes: 15d024d4aa ("hw/block/nvme: split setup and register for namespace")
Cc: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
2021-02-11 14:23:08 +01:00
Bin Meng 2132cfe52b hw/block/nvme: Fix a build error in nvme_get_feature()
Current QEMU HEAD nvme.c does not compile with the default GCC 5.4
on a Ubuntu 16.04 host:

  hw/block/nvme.c:3242:9: error: ‘result’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
         trace_pci_nvme_getfeat_vwcache(result ? "enabled" : "disabled");
         ^
  hw/block/nvme.c:3150:14: note: ‘result’ was declared here
     uint32_t result;
              ^

Explicitly initialize the result to fix it.

Fixes: aa5e55e3b0 ("hw/block/nvme: open code for volatile write cache")
Fixes: Coverity CID 1446371
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
2021-02-11 14:22:30 +01:00
Klaus Jensen 886188a9c1 hw/block/nvme: fix legacy namespace registration
Moving namespace registration to the nvme-ns realization function had
the unintended side-effect of breaking legacy namespace registration.
Fix this.

Fixes: 15d024d4aa ("hw/block/nvme: split setup and register for namespace")
Reported-by: Alexander Graf <agraf@csgraf.de>
Cc: Minwoo Im <minwoo.im.dev@gmail.com>
Tested-by: Alexander Graf <agraf@csgraf.de>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
2021-02-11 14:11:17 +01:00
Peter Maydell 932a8d1f11 arm: Update infocenter.arm.com URLs
Update infocenter.arm.com URLs for various pieces of Arm
documentation to the new developer.arm.com equivalents.  (There is a
redirection in place from the old URLs, but we might as well update
our comments in case the redirect ever disappears in future.)

This patch covers all the URLs which are not MPS2/SSE-200/IoTKit
related (those are dealt with in a different patch).

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210205171456.19939-1-peter.maydell@linaro.org
2021-02-11 11:50:14 +00:00
Hao Wu 377a3ba25c hw/arm: Remove GPIO from unimplemented NPCM7XX
NPCM7XX GPIO devices have been implemented in hw/gpio/npcm7xx-gpio.c. So
we removed them from the unimplemented devices list.

Reviewed-by: Doug Evans<dje@google.com>
Reviewed-by: Tyrong Ting<kfting@nuvoton.com>
Signed-off-by: Hao Wu<wuhaotsh@google.com>
Message-id: 20210129005845.416272-2-wuhaotsh@google.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2021-02-11 11:50:13 +00:00
Peter Maydell 83339e21d0 Pull request
v4:
  * Add PCI_EXPRESS Kconfig dependency to fix s390x in "multi-process: setup PCI
    host bridge for remote device" [Philippe and Thomas]
 -----BEGIN PGP SIGNATURE-----
 
 iQEzBAABCAAdFiEEhpWov9P5fNqsNXdanKSrs4Grc8gFAmAjprYACgkQnKSrs4Gr
 c8g8fwgAspVVcW0x2uBdrbbi2PSOtpTu+GGC8gYcvGS526WSINv+mY8QhUFPdaQO
 MErATW1FuIYuXBkvXcaIRWQGGZkfWd6AyjxjEls2jdcp1ScqJ+wnZmTDsgR8yIb3
 vOdsA03YJugrAmF4Lsdpkyq9KaWYlCUxrdPoagEopQCEETkKeEOXq40c3pxzeIBI
 75s8i28makJ8Logdvr9SBLsR7DL4mpoVQErUe2IMLGGbPSe5F49VD+b/qI20agoI
 7L8mDXqL02nc2qJL63hk2dq7pq++MWq0uDs8bbaCouxiFNrNA8zQ+flLP0VrFcP/
 gJUa92unwoKs+yVVppadBZKwjtkbYA==
 =r5oQ
 -----END PGP SIGNATURE-----

Merge remote-tracking branch 'remotes/stefanha-gitlab/tags/block-pull-request' into staging

Pull request

v4:
 * Add PCI_EXPRESS Kconfig dependency to fix s390x in "multi-process: setup PCI
   host bridge for remote device" [Philippe and Thomas]

# gpg: Signature made Wed 10 Feb 2021 09:26:14 GMT
# gpg:                using RSA key 8695A8BFD3F97CDAAC35775A9CA4ABB381AB73C8
# gpg: Good signature from "Stefan Hajnoczi <stefanha@redhat.com>" [full]
# gpg:                 aka "Stefan Hajnoczi <stefanha@gmail.com>" [full]
# Primary key fingerprint: 8695 A8BF D3F9 7CDA AC35  775A 9CA4 ABB3 81AB 73C8

* remotes/stefanha-gitlab/tags/block-pull-request: (27 commits)
  docs: fix Parallels Image "dirty bitmap" section
  multi-process: perform device reset in the remote process
  multi-process: Retrieve PCI info from remote process
  multi-process: create IOHUB object to handle irq
  multi-process: Synchronize remote memory
  multi-process: PCI BAR read/write handling for proxy & remote endpoints
  multi-process: Forward PCI config space acceses to the remote process
  multi-process: add proxy communication functions
  multi-process: introduce proxy object
  multi-process: setup memory manager for remote device
  multi-process: Associate fd of a PCIDevice with its object
  multi-process: Initialize message handler in remote device
  multi-process: define MPQemuMsg format and transmission functions
  io: add qio_channel_readv_full_all_eof & qio_channel_readv_full_all helpers
  io: add qio_channel_writev_full_all helper
  multi-process: setup a machine object for remote device process
  multi-process: setup PCI host bridge for remote device
  multi-process: Add config option for multi-process QEMU
  memory: alloc RAM from file at offset
  multi-process: add configure and usage information
  ...

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2021-02-10 15:42:20 +00:00
Elena Ufimtseva b6cc02d98f multi-process: perform device reset in the remote process
Perform device reset in the remote process when QEMU performs
device reset. This is required to reset the internal state
(like registers, etc...) of emulated devices

Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 7cb220a51f565dc0817bd76e2f540e89c2d2b850.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
2021-02-10 09:23:28 +00:00
Jagannathan Raman 1bec145cd9 multi-process: Retrieve PCI info from remote process
Retrieve PCI configuration info about the remote device and
configure the Proxy PCI object based on the returned information

Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 85ee367bbb993aa23699b44cfedd83b4ea6d5221.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
2021-02-10 09:23:28 +00:00
Jagannathan Raman bd36adb8df multi-process: create IOHUB object to handle irq
IOHUB object is added to manage PCI IRQs. It uses KVM_IRQFD
ioctl to create irqfd to injecting PCI interrupts to the guest.
IOHUB object forwards the irqfd to the remote process. Remote process
uses this fd to directly send interrupts to the guest, bypassing QEMU.

Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 51d5c3d54e28a68b002e3875c59599c9f5a424a1.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
2021-02-10 09:23:28 +00:00
Jagannathan Raman c746b74a7d multi-process: Synchronize remote memory
Add ProxyMemoryListener object which is used to keep the view of the RAM
in sync between QEMU and remote process.
A MemoryListener is registered for system-memory AddressSpace. The
listener sends SYNC_SYSMEM message to the remote process when memory
listener commits the changes to memory, the remote process receives
the message and processes it in the handler for SYNC_SYSMEM message.

Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 04fe4e6a9ca90d4f11ab6f59be7652f5b086a071.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
2021-02-10 09:23:28 +00:00
Jagannathan Raman 7ee3f82384 multi-process: PCI BAR read/write handling for proxy & remote endpoints
Proxy device object implements handler for PCI BAR writes and reads.
The handler uses BAR_WRITE/BAR_READ message to communicate to the
remote process with the BAR address and value to be written/read.
The remote process implements handler for BAR_WRITE/BAR_READ
message.

Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: a8b76714a9688be5552c4c92d089bc9e8a4707ff.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
2021-02-10 09:23:28 +00:00
Elena Ufimtseva 11ab872588 multi-process: Forward PCI config space acceses to the remote process
The Proxy Object sends the PCI config space accesses as messages
to the remote process over the communication channel

Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: d3c94f4618813234655356c60e6f0d0362ff42d6.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
2021-02-10 09:23:28 +00:00
Elena Ufimtseva e7b2c9eaa2 multi-process: add proxy communication functions
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: d54edb4176361eed86b903e8f27058363b6c83b3.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
2021-02-10 09:23:28 +00:00
Elena Ufimtseva 9f8112073a multi-process: introduce proxy object
Defines a PCI Device proxy object as a child of TYPE_PCI_DEVICE.

Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: b5186ebfedf8e557044d09a768846c59230ad3a7.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
2021-02-10 09:23:28 +00:00
Jagannathan Raman ed5d001916 multi-process: setup memory manager for remote device
SyncSysMemMsg message format is defined. It is used to send
file descriptors of the RAM regions to remote device.
RAM on the remote device is configured with a set of file descriptors.
Old RAM regions are deleted and new regions, each with an fd, is
added to the RAM.

Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 7d2d1831d812e85f681e7a8ab99e032cf4704689.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
2021-02-10 09:23:28 +00:00
Jagannathan Raman c7d80c7c1d multi-process: Associate fd of a PCIDevice with its object
Associate the file descriptor for a PCIDevice in remote process with
DeviceState object.

Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: f405a2ed5d7518b87bea7c59cfdf334d67e5ee51.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
2021-02-10 09:23:28 +00:00
Jagannathan Raman 48b06f50d8 multi-process: Initialize message handler in remote device
Initializes the message handler function in the remote process. It is
called whenever there's an event pending on QIOChannel that registers
this function.

Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 99d38d8b93753a6409ac2340e858858cda59ab1b.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
2021-02-10 09:23:28 +00:00
Elena Ufimtseva ad22c3088b multi-process: define MPQemuMsg format and transmission functions
Defines MPQemuMsg, which is the message that is sent to the remote
process. This message is sent over QIOChannel and is used to
command the remote process to perform various tasks.
Define transmission functions used by proxy and by remote.

Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 56ca8bcf95195b2b195b08f6b9565b6d7410bce5.1611938319.git.jag.raman@oracle.com

[Replace struct iovec send[2] = {0} with {} to make clang happy as
suggested by Peter Maydell <peter.maydell@linaro.org>.
--Stefan]

Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
2021-02-10 09:23:28 +00:00
Jagannathan Raman 3f0e7e57a3 multi-process: setup a machine object for remote device process
x-remote-machine object sets up various subsystems of the remote
device process. Instantiate PCI host bridge object and initialize RAM, IO &
PCI memory regions.

Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: c537f38d17f90453ca610c6b70cf3480274e0ba1.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
2021-02-10 09:23:28 +00:00
Jagannathan Raman 6fbd84d632 multi-process: setup PCI host bridge for remote device
PCI host bridge is setup for the remote device process. It is
implemented using remote-pcihost object. It is an extension of the PCI
host bridge setup by QEMU.
Remote-pcihost configures a PCI bus which could be used by the remote
PCI device to latch on to.

Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 0871ba857abb2eafacde07e7fe66a3f12415bfb2.1611938319.git.jag.raman@oracle.com

[Added PCI_EXPRESS condition in hw/remote/Kconfig since remote-pcihost
needs PCIe. This solves "make check" failure on s390x. Fix suggested by
Philippe Mathieu-Daudé <philmd@redhat.com> and Thomas Huth
<thuth@redhat.com>.
--Stefan]

Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
2021-02-10 09:23:22 +00:00
Bin Meng ce8e43760e hw/net: fsl_etsec: Reverse the RCTRL.RSF logic
Per MPC8548ERM [1] chapter 14.5.3.4.1:

When RCTRL.RSF is 1, frames less than 64 bytes are accepted upon
a DA match. But currently QEMU does the opposite. This commit
reverses the RCTRL.RSF testing logic to match the manual.

Due to the reverse of the logic, certain guests may potentially
break if they don't program eTSEC to have RCTRL.RSF bit set.
When RCTRL.RSF is 0, short frames are silently dropped, however
as of today both slirp and tap networking do not pad short frames
(e.g.: an ARP packet) to the minimum frame size of 60 bytes. So
ARP requests will be dropped, preventing the guest from becoming
visible on the network.

The same issue was reported on e1000 and vmxenet3 before, see:

commit 78aeb23ede ("e1000: Pad short frames to minimum size (60 bytes)")
commit 40a87c6c9b ("vmxnet3: Pad short frames to minimum size (60 bytes)")

[1] https://www.nxp.com/docs/en/reference-manual/MPC8548ERM.pdf

Fixes: eb1e7c3e51 ("Add Enhanced Three-Speed Ethernet Controller (eTSEC)")
Signed-off-by: Bin Meng <bin.meng@windriver.com>

Message-Id: <1612923021-19746-1-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
2021-02-10 14:50:11 +11:00
Bin Meng 11dbcc70c6 hw/ppc: e500: Fill in correct <clock-frequency> for the serial nodes
At present the <clock-frequency> property of the serial node is
populated with value zero. U-Boot's ns16550 driver is not happy
about this, so let's fill in a meaningful value.

Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>

Message-Id: <1612362288-22216-2-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
2021-02-10 14:50:11 +11:00
Bin Meng 0c36ab7114 hw/ppc: e500: Use a macro for the platform clock frequency
At present the platform clock frequency is using a magic number.
Convert it to a macro and use it everywhere.

Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>

Message-Id: <1612362288-22216-1-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
2021-02-10 14:50:11 +11:00
Cédric Le Goater dd7ef911b3 ppc/pnv: Set default RAM size to 1 GB
The memory layout of the PowerNV machine is defined as :

  #define KERNEL_LOAD_BASE	((void *)0x20000000)
  #define KERNEL_LOAD_SIZE	0x08000000

  #define INITRAMFS_LOAD_BASE	KERNEL_LOAD_BASE + KERNEL_LOAD_SIZE
  #define INITRAMFS_LOAD_SIZE	0x08000000

  #define SKIBOOT_BASE		0x30000000
  #define SKIBOOT_SIZE		0x01c10000

  #define CPU_STACKS_BASE	(SKIBOOT_BASE + SKIBOOT_SIZE)
  #define STACK_SHIFT		15
  #define STACK_SIZE		(1 << STACK_SHIFT)

The overall size of the CPU stacks is (max PIR + 1) * 32K and the
machine easily reaches 800MB of minimum required RAM.

Any value below will result in a skiboot crash :

    [    0.034949905,3] MEM: Partial overlap detected between regions:
    [    0.034959039,3] MEM: ibm,firmware-stacks [0x31c10000-0x3a450000] (new)
    [    0.034968576,3] MEM: ibm,firmware-allocs-memory@0 [0x31c10000-0x38400000]
    [    0.034980367,3] Out of memory adding skiboot reserved areas
    [    0.035074945,3] ***********************************************
    [    0.035093627,3] < assert failed at core/mem_region.c:1129 >
    [    0.035104247,3]     .
    [    0.035108025,3]      .
    [    0.035111651,3]       .
    [    0.035115231,3]         OO__)
    [    0.035119198,3]        <"__/
    [    0.035122980,3]         ^ ^

Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210129111719.790692-1-clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
2021-02-10 14:50:11 +11:00
Daniel Henrique Barboza b01fec3659 spapr_numa.c: fix ibm,max-associativity-domains calculation
The current logic for calculating 'maxdomain' making it a sum of
numa_state->num_nodes with spapr->gpu_numa_id. spapr->gpu_numa_id is
used as a index to determine the next available NUMA id that a
given NVGPU can use.

The problem is that the initial value of gpu_numa_id, for any topology
that has more than one NUMA node, is equal to numa_state->num_nodes.
This means that our maxdomain will always be, at least, twice the
amount of existing NUMA nodes. This means that a guest with 4 NUMA
nodes will end up with the following max-associativity-domains:

rtas/ibm,max-associativity-domains
                 00000004 00000008 00000008 00000008 00000008

This overtuning of maxdomains doesn't go unnoticed in the guest, being
detected in SLUB during boot:

 dmesg | grep SLUB
[    0.000000] SLUB: HWalign=128, Order=0-3, MinObjects=0, CPUs=4, Nodes=8

SLUB is detecting 8 total nodes, with 4 nodes being online.

This patch fixes ibm,max-associativity-domains by considering the amount
of NVGPUs NUMA nodes presented in the guest, instead of just
spapr->gpu_numa_id.

Reported-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210128174213.1349181-4-danielhb413@gmail.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
2021-02-10 10:43:50 +11:00
Daniel Henrique Barboza 6640706972 spapr_numa.c: create spapr_numa_initial_nvgpu_numa_id() helper
We'll need to check the initial value given to spapr->gpu_numa_id when
building the rtas DT, so put it in a helper for easier access and to
avoid repetition.

Tested-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210128174213.1349181-3-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
2021-02-10 10:43:50 +11:00
Daniel Henrique Barboza 3b880445e6 spapr: move spapr_machine_using_legacy_numa() to spapr_numa.c
This function is used only in spapr_numa.c.

Tested-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210128174213.1349181-2-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
2021-02-10 10:43:50 +11:00
Cédric Le Goater 032c226bc6 ppc/pnv: Introduce a LPC FW memory region attribute to map the PNOR
This to map the PNOR from the machine init handler directly and finish
the cleanup of the LPC model.

Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210126171059.307867-8-clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
2021-02-10 10:43:50 +11:00
Cédric Le Goater 8304ab7905 ppc/pnv: Remove default disablement of the PNOR contents
On PowerNV systems, the BMC is in charge of mapping the PNOR contents
on the LPC FW address space using the HIOMAP protocol. Under QEMU, we
emulate this behavior and we also add an extra control on the flash
accesses by letting the HIOMAP command handler decide whether the
memory region is accessible or not depending on the firmware requests.

However, this behavior is not compatible with hostboot like firmwares
which need this mapping to be always available. For this reason, the
PNOR memory region is initially disabled for skiboot mode only.

This is badly placed under the LPC model and requires the use of the
machine. Since it doesn't add much, simply remove the initial setting.
The extra control in the HIOMAP command handler will still be performed.

Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210126171059.307867-7-clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
2021-02-10 10:43:50 +11:00
Cédric Le Goater 50ae2452b5 ppc/pnv: Discard internal BMC initialization when BMC is external
The PowerNV machine can be run with an external IPMI BMC device
connected to a remote QEMU machine acting as BMC, using these options :

  -chardev socket,id=ipmi0,host=localhost,port=9002,reconnect=10 \
  -device ipmi-bmc-extern,id=bmc0,chardev=ipmi0 \
  -device isa-ipmi-bt,bmc=bmc0,irq=10 \
  -nodefaults

In that case, some aspects of the BMC initialization should be
skipped, since they rely on the simulator interface.

Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210126171059.307867-6-clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
2021-02-10 10:43:50 +11:00
Cédric Le Goater 60ef80101e ppc/pnv: Simplify pnv_bmc_create()
and reuse pnv_bmc_set_pnor() to share the setting of the PNOR.

Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210126171059.307867-5-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
2021-02-10 10:43:50 +11:00
Cédric Le Goater 05ce9b73b8 ppc/pnv: Use skiboot addresses to load kernel and ramfs
The current settings are useful to load large kernels (with debug) but
it moves the initrd image in a memory region not protected by
skiboot. If skiboot is compiled with DEBUG=1, memory poisoning will
corrupt the initrd.

Cc: Murilo Opsfelder Araujo <muriloo@linux.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210126171059.307867-4-clg@kaod.org>
Reviewed-by: Murilo Opsfelder Araujo <muriloo@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
2021-02-10 10:43:50 +11:00
Cédric Le Goater cb9428642e ppc/xive: Add firmware bit when dumping the ENDs
ENDs allocated by OPAL for the HW thread VPs are tagged as owned by FW.
Dump the state in 'info pic'.

Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210126171059.307867-3-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
2021-02-10 10:43:50 +11:00
Cédric Le Goater 2cfc9f1a96 ppc/pnv: Add trace events for PCI event notification
On POWER9 systems, PHB controllers signal the XIVE interrupt controller
of a source interrupt notification using a store on a MMIO region. Add
traces for such events.

Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210126171059.307867-2-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
2021-02-10 10:43:50 +11:00
Greg Kurz 040bdafce1 spapr: Adjust firmware path of PCI devices
It is currently not possible to perform a strict boot from USB storage:

$ qemu-system-ppc64 -accel kvm -nodefaults -nographic -serial stdio \
	-boot strict=on \
	-device qemu-xhci \
	-device usb-storage,drive=disk,bootindex=0 \
	-blockdev driver=file,node-name=disk,filename=fedora-ppc64le.qcow2

SLOF **********************************************************************
QEMU Starting
 Build Date = Jul 17 2020 11:15:24
 FW Version = git-e18ddad8516ff2cf
 Press "s" to enter Open Firmware.

Populating /vdevice methods
Populating /vdevice/vty@71000000
Populating /vdevice/nvram@71000001
Populating /pci@800000020000000
                     00 0000 (D) : 1b36 000d    serial bus [ usb-xhci ]
No NVRAM common partition, re-initializing...
Scanning USB
  XHCI: Initializing
    USB Storage
       SCSI: Looking for devices
          101000000000000 DISK     : "QEMU     QEMU HARDDISK    2.5+"
Using default console: /vdevice/vty@71000000

  Welcome to Open Firmware

  Copyright (c) 2004, 2017 IBM Corporation All rights reserved.
  This program and the accompanying materials are made available
  under the terms of the BSD License available at
  http://www.opensource.org/licenses/bsd-license.php

Trying to load:  from: /pci@800000020000000/usb@0/storage@1/disk@101000000000000 ...
E3405: No such device

E3407: Load failed

  Type 'boot' and press return to continue booting the system.
  Type 'reset-all' and press return to reboot the system.

Ready!
0 >

The device tree handed over by QEMU to SLOF indeed contains:

qemu,boot-list =
	"/pci@800000020000000/usb@0/storage@1/disk@101000000000000 HALT";

but the device node is named usb-xhci@0, not usb@0.

This happens because the firmware names of PCI devices returned
by get_boot_devices_list() come from pcibus_get_fw_dev_path(),
while the sPAPR PHB code uses a different naming scheme for
device nodes. This inconsistency has always been there but it was
hidden for a long time because SLOF used to rename USB device
nodes, until this commit, merged in QEMU 4.2.0 :

commit 85164ad4ed
Author: Alexey Kardashevskiy <aik@ozlabs.ru>
Date:   Wed Sep 11 16:24:32 2019 +1000

    pseries: Update SLOF firmware image

    This fixes USB host bus adapter name in the device tree to match QEMU's
    one.

    Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
    Signed-off-by: David Gibson <david@gibson.dropbear.id.au>

Fortunately, sPAPR implements the firmware path provider interface.
This provides a way to override the default firmware paths.

Just factor out the sPAPR PHB naming logic from spapr_dt_pci_device()
to a helper, and use it in the sPAPR firmware path provider hook.

Fixes: 85164ad4ed ("pseries: Update SLOF firmware image")
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <20210122170157.246374-1-groug@kaod.org>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
2021-02-10 10:43:50 +11:00
Daniel Henrique Barboza a85bb34e1c spapr.c: add 'name' property for hotplugged CPUs nodes
In the CPU hotunplug bug [1] the guest kernel throws a scary
message in dmesg:

pseries-hotplug-cpu: Failed to offline CPU <NULL>, rc: -16

The reason isn't related to the bug though. This happens because the
kernel file arch/powerpc/platform/pseries/hotplug-cpu.c, function
dlpar_cpu_remove(), is not finding the device_node.name of the offending
CPU.

We're not populating the 'name' property for hotplugged CPUs. Since the
kernel relies on device_node.name for identifying CPU nodes, and the
CPUs that are coldplugged has the 'name' property filled by SLOF, this
is creating an unneeded inconsistency between hotplug and coldplug CPUs
in the kernel.

Let's fill the 'name' property for hotplugged CPUs as well. This will
make the guest dmesg throws a less intimidating message when we try to
unplug the last online CPU:

pseries-hotplug-cpu: Failed to offline CPU PowerPC,POWER9@1, rc: -16

[1] https://bugzilla.redhat.com/1911414

Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210120232305.241521-3-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
2021-02-10 10:43:49 +11:00
Daniel Henrique Barboza 7265bc3e54 spapr.c: use g_auto* with 'nodename' in CPU DT functions
Next patch will use the 'nodename' string in spapr_core_dt_populate()
after the point it's being freed today.

Instead of moving 'g_free(nodename)' around, let's do a QoL change in
both CPU DT functions where 'nodename' is being freed, and use
g_autofree to avoid the 'g_free()' call altogether.

Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210120232305.241521-2-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
2021-02-10 10:43:49 +11:00
Jagannathan Raman 3090de695b multi-process: Add config option for multi-process QEMU
Add configuration options to enable or disable multiprocess QEMU code

Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 6cc37253e35418ebd7b675a31a3df6e3c7a12dc1.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
2021-02-09 20:53:56 +00:00
Jagannathan Raman 44a4ff31c0 memory: alloc RAM from file at offset
Allow RAM MemoryRegion to be created from an offset in a file, instead
of allocating at offset of 0 by default. This is needed to synchronize
RAM between QEMU & remote process.

Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 609996697ad8617e3b01df38accc5c208c24d74e.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
2021-02-09 20:53:56 +00:00
Peter Maydell 1214d55d1c Emulated NVMe device updates
* deallocate or unwritten logical block error feature (me)
   * dataset management command (me)
   * compare command (Gollu Appalanaidu)
   * namespace types (Niklas Cassel)
   * zoned namespaces (Dmitry Fomichev)
   * smart critical warning toggle (Zhenwei Pi)
   * allow cmb and pmr to coexist (me)
   * pmr rds/wds support (Naveen Nagar)
   * cmb v1.4 logic (Padmakar Kalghatgi)
 
 And a lot of smaller fixes from Gollu Appalanaidu and Minwoo Im.
 -----BEGIN PGP SIGNATURE-----
 
 iQEzBAABCAAdFiEEUigzqnXi3OaiR2bATeGvMW1PDekFAmAiON4ACgkQTeGvMW1P
 DenhxQf/WzoiO5bXmvZeRv+IHoIn5GhJ1NxLRYO5MX0diswh0BBwUmIscbEDMe1b
 GsD6rpd9YfEO80L/sEGqgV09HT+6e8YwDsNNZBTAsUNRVx0WxckgcGWcrzNNA9Nc
 WEl0Q8si5USSQ1C7djplLXdR6p4pbA/gIk6AjNIo3q2VK1ZqCBhQGESGEfGgrAXW
 xWo8C1V8dnKdxUYI2blbti44sElHZJ6jcF5N3Xmv0UUa1WL0hh0u6qr7IbCZe1kO
 SUFWMIGLF+1C35MUyWpgCjCn5cUdnTA0s/SLEuWtDlNYRhRRh0D6LZviVTZi38Wx
 6Cxg/bRkSlcKo1/jswwYcAaH7qQ4Eg==
 =NB9D
 -----END PGP SIGNATURE-----

Merge remote-tracking branch 'remotes/nvme/tags/nvme-next-pull-request' into staging

Emulated NVMe device updates

  * deallocate or unwritten logical block error feature (me)
  * dataset management command (me)
  * compare command (Gollu Appalanaidu)
  * namespace types (Niklas Cassel)
  * zoned namespaces (Dmitry Fomichev)
  * smart critical warning toggle (Zhenwei Pi)
  * allow cmb and pmr to coexist (me)
  * pmr rds/wds support (Naveen Nagar)
  * cmb v1.4 logic (Padmakar Kalghatgi)

And a lot of smaller fixes from Gollu Appalanaidu and Minwoo Im.

# gpg: Signature made Tue 09 Feb 2021 07:25:18 GMT
# gpg:                using RSA key 522833AA75E2DCE6A24766C04DE1AF316D4F0DE9
# gpg: Good signature from "Klaus Jensen <its@irrelevant.dk>" [unknown]
# gpg:                 aka "Klaus Jensen <k.jensen@samsung.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg:          There is no indication that the signature belongs to the owner.
# Primary key fingerprint: DDCA 4D9C 9EF9 31CC 3468  4272 63D5 6FC5 E55D A838
#      Subkey fingerprint: 5228 33AA 75E2 DCE6 A247  66C0 4DE1 AF31 6D4F 0DE9

* remotes/nvme/tags/nvme-next-pull-request: (56 commits)
  hw/block/nvme: refactor the logic for zone write checks
  hw/block/nvme: fix zone boundary check for append
  hw/block/nvme: fix wrong parameter name 'cross_read'
  hw/block/nvme: align with existing style
  hw/block/nvme: fix set feature save field check
  hw/block/nvme: fix set feature for error recovery
  hw/block/nvme: error if drive less than a zone size
  hw/block/nvme: lift cmb restrictions
  hw/block/nvme: bump to v1.4
  hw/block/nvme: move cmb logic to v1.4
  hw/block/nvme: add PMR RDS/WDS support
  hw/block/nvme: disable PMR at boot up
  hw/block/nvme: remove redundant zeroing of PMR registers
  hw/block/nvme: rename PMR/CMB shift/mask fields
  hw/block/nvme: allow cmb and pmr to coexist
  hw/block/nvme: move msix table and pba to BAR 0
  hw/block/nvme: indicate CMB support through controller capabilities register
  hw/block/nvme: fix 64 bit register hi/lo split writes
  hw/block/nvme: add size to mmio read/write trace events
  hw/block/nvme: trigger async event during injecting smart warning
  ...

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2021-02-09 13:24:37 +00:00
Peter Maydell 41d306ec7d * Fuzzing improvements (Qiuhao, Alexander)
* i386: Fix BMI decoding for instructions with the 0x66 prefix (David)
 * initial attempt at fixing event_notifier emulation (Maxim)
 * i386: PKS emulation, fix for "qemu-system-i386 -cpu host" (myself)
 * meson: RBD test fixes (myself)
 * meson: TCI warnings (Philippe)
 * Leaner build for --disable-guest-agent, --disable-system and
   --disable-tools (Philippe, Stefan)
 * --enable-tcg-interpreter fix (Richard)
 * i386: SVM feature bits (Wei)
 * KVM bugfix (Thomas H.)
 * Add missing MemoryRegionOps callbacks (PJP)
 -----BEGIN PGP SIGNATURE-----
 
 iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmAhR4cUHHBib256aW5p
 QHJlZGhhdC5jb20ACgkQv/vSX3jHroOviAf/Ymk/KwHZKySVqHOjDZnvP5PXMAru
 p1zlMRLAorXK+CTbshkIliaQyD8ggzT4HCinJ2NisdfTWMmlWbgr8gahNqKyZ5UG
 HlL28va3dvGhelswh/CNso1ZhVb2Q+aAYn/c6LXQva2r0xi26ohJTkIkSCPP/bnI
 +73dGzwAilBOsBVbn4cCm/70XtwDpPkw41IZIDoy/4lhL8ZdpHMz8oOjNIlOdlcU
 aEDfM8vYE4C70OtUlRZ1OwVxzcjS1Bf6dQYcpg5gAKy/jAAqR+v2PStxXiUuj5D3
 cAzd03Goh78Wcre+CbWxDKGcGtiooUT+J09wmvDPYVUHcpQMbumf4MufrQ==
 =INB5
 -----END PGP SIGNATURE-----

Merge remote-tracking branch 'remotes/bonzini-gitlab/tags/for-upstream' into staging

* Fuzzing improvements (Qiuhao, Alexander)
* i386: Fix BMI decoding for instructions with the 0x66 prefix (David)
* initial attempt at fixing event_notifier emulation (Maxim)
* i386: PKS emulation, fix for "qemu-system-i386 -cpu host" (myself)
* meson: RBD test fixes (myself)
* meson: TCI warnings (Philippe)
* Leaner build for --disable-guest-agent, --disable-system and
  --disable-tools (Philippe, Stefan)
* --enable-tcg-interpreter fix (Richard)
* i386: SVM feature bits (Wei)
* KVM bugfix (Thomas H.)
* Add missing MemoryRegionOps callbacks (PJP)

# gpg: Signature made Mon 08 Feb 2021 14:15:35 GMT
# gpg:                using RSA key F13338574B662389866C7682BFFBD25F78C7AE83
# gpg:                issuer "pbonzini@redhat.com"
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>" [full]
# gpg:                 aka "Paolo Bonzini <pbonzini@redhat.com>" [full]
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4  E2F7 7E15 100C CD36 69B1
#      Subkey fingerprint: F133 3857 4B66 2389 866C  7682 BFFB D25F 78C7 AE83

* remotes/bonzini-gitlab/tags/for-upstream: (46 commits)
  target/i386: Expose VMX entry/exit load pkrs control bits
  target/i386: Add support for save/load IA32_PKRS MSR
  imx7-ccm: add digprog mmio write method
  tz-ppc: add dummy read/write methods
  spapr_pci: add spapr msi read method
  nvram: add nrf51_soc flash read method
  prep: add ppc-parity write method
  vfio: add quirk device write method
  pci-host: designware: add pcie-msi read method
  hw/pci-host: add pci-intack write method
  cpu-throttle: Remove timer_mod() from cpu_throttle_set()
  replay: rng-builtin support
  pc-bios/descriptors: fix paths in json files
  replay: fix replay of the interrupts
  accel/kvm/kvm-all: Fix wrong return code handling in dirty log code
  qapi/meson: Restrict UI module to system emulation and tools
  qapi/meson: Restrict system-mode specific modules
  qapi/meson: Remove QMP from user-mode emulation
  qapi/meson: Restrict qdev code to system-mode emulation
  meson: Restrict emulation code
  ...

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2021-02-09 10:04:51 +00:00
Klaus Jensen 3e22762edc hw/block/nvme: refactor the logic for zone write checks
Refactor the zone write check logic such that the most "meaningful"
error is returned first. That is, first, if the zone is not writable,
return an appropriate status code for that. Then, make sure we are
actually writing at the write pointer and finally check that we do not
cross the zone write boundary. This aligns with the "priority" of status
codes for zone read checks.

Also add a couple of additional descriptive trace events and remove an
always true assert.

Cc: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Tested-by: Niklas Cassel <niklas.cassel@wdc.com>
Tested-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
2021-02-08 21:15:54 +01:00