Error checking in ahci's handle_cmd is re-ordered so that we
initialize as few things as possible before we've done our
sanity checking. This simplifies returning from this call
in case of an error.
A check to make sure the DMA memory map succeeds with the
correct size is also added, and the debug print of the
command fis is cleaned up with its size corrected.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1415058979-16604-4-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This patch introduces a few changes to how FIS packets are
deciphered in the AHCI virtual device. The summary of
changes can be grouped into two pieces:
[A] Changes to how we apply a preliminary sieve to FISes,
[B] Changes in how we internalize a decomposed FIS.
== Changes to how we apply a preliminary sieve to FISes ==
(1) Packets may now either update the Control register or
the Command register, but not both. This is according
to the SATA 3.2 specification which states:
"...the device either initiates processing of the command
indicated in the Command register or initiates processing
of the control request indicated [...] depending on the
state of the C bit in the FIS."
See SATA 3.2 section 10.5.5.4, "Reception" in the 10.5.5
"Register Host to Device FIS" section.
This change accounts for the first two regions of change
within the diff. All other changes belong to the following
changes.
== Changes in how we internalize a decomposed FIS ==
(2) Instead of trying to extract the sector number out of the
FIS from bytes 4-10 and setting it with ide_set_sector,
we set the appropriate IDEState registers and trust that
ide_get_sector can retrieve the correct sector later.
By "constructing" the sector for use with ide_set_sector,
we are duplicating the mechanisms of ide_get_sector.
This change makes the FIS decomposition more obvious.
SATA 3.2 as a specification does not make the legacy
register mapping with respect to the D2H FIS obvious.
However, SATA 3.2 section 10.5.5.1 "Register Host to
Device FIS layout" describes all of the "cmd_fis"
bytes:
0 - FIS Type (0x27)
1 - Port Multiplier Port and Command Update flag
2 - ATA Command
3 - Features_Low
4 - LBA 7:0
5 - LBA 15:8
6 - LBA 23:16
7 - Device, AKA "Drive Select."
8 - LBA 31:24
9 - LBA 39:32
10 - LBA 47:40
11 - Features_High
12 - Count Low
13 - Count High
14 - ICC
15 - Control
16-19 - Auxiliary (for NCQ, defined per-command)
Most of these registers map to existing IDEState registers
in obvious ways, especially features, select, hob_features,
and nsector (count). ICC is reserved in older specifications
but is not supported in our implementation, and remains
unused here. The Control register is not valid for a command
that is trying to update the command register and is to be
considered reserved at this point.
What is not obvious is the LBA register mappings, but SATA 1.0
can help inform of us legacy device support, see SATA 1.0 section
8.5.2 "Register - Host to Device."
LBA 7:0 - Sector Number (sector)
LBA 15:8 - Cyl Low (lcyl)
LBA 23:16 - Cyl High (hcyl)
LBA 31:24 - Sector Num Exp. (hob_sector)
LBA 39:32 - Cyl Low Exp. (hob_lcyl)
LBA 47:40 - Cyl High Exp. (hob_hcyl)
These mappings help guide which registers the FIS should be decomposed
into/towards for CHS, LBA28 and LBA48 commands.
As a note: The prior confusion that can be seen in the documentation
arises from the fact that CHS and LBA28 commands use the low nybble
of the drive select register to store LBA 27:24, whereas LNA48 commands
use the hob_sector, hob_lcyl and hob_hcyl registers as explained above.
The decomposition as it stands now will correctly decompose CHS, LBA28
and LBA48 commands into their appropriate registers where the core
IDE/ATAPI layers can deal with them correctly.
See the below point for more information.
(3) We save cmd_fis[7] as ide_state->select, which informs
decisions about if we are using LBA or CHS.
This corrects a bug in AHCI wherein we attempt to set and/or
retrieve the sector number by using ide_set_sector and
ide_get_sector, which depend on the select register to
determine if we are using LBA or CHS.
Without this adjustment, LBA48 read/writes are currently
broken. Thanks to Eniac Zheng @ HP for pointing this out.
(4) Save cmd_fis[11] as ide_state->hob_feature, as defined in SATA 3.2.
(5) For several ATA commands, the sector count register set to 0
is a magic number that means 256 sectors. For LBA48 commands,
this means 65,536 sectors. We drop the magic sector correction
here, and trust the ide core layer to handle the conversion
appropriately, in ide_cmd_lba48_transform(). As it stands,
the current AHCI code is only compliant with LBA28 commands.
By simply removing the magic, it will work with LBA28 and LBA48.
(6) We expand FIS decomposition to include both ATAPI and IDE devices.
We leave the logic of determining if the fields are valid or not
to the respective layers.
This change intends to make it clearer that AHCI is only a
composition mechanism for the FIS packets: the meanings of
the registers is best left to the implementation layers for
those devices.
(7) Forcefully setting the feature, hcyl and lcyl registers for ATAPI
commands is removed.
- The hcyl and lcyl magic present here is valid at boot only,
and should not be overridden for every PACKET command.
- The feature register is defined as valid for the PACKET command,
so we should not suppress it. The ATAPI layer does not even
currently depend on or require 0x01 as mandatory.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1415058979-16604-3-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
A small helper to determine which S/ATA commands
are destined to be routed to the NCQ pathways.
This references SATA 3.2 section 13.6,
Native Command Queueing. See sections 13.6.4,
13.6.5, 13.6.6, 13.6.7 and 13.6.8 for all
SATA commands considered to be part of the
NCQ feature set. This is summarized in a small
list in section 13.6.3.1 and again in 13.6.3.2.
Not all of these NCQ commands are currently supported,
so the error pathways are adjusted slightly to be more
informative in the case they are encountered.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1415058979-16604-2-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This impacts both BMDMA and AHCI HBA interfaces for IDE.
Currently, we confuse the difference between a PRDT having
"0 bytes" and a PRDT having "0 complete sectors."
When we receive an incomplete sector, inconsistent error checking
leads to an infinite loop wherein the call succeeds, but it
didn't give us enough bytes -- leading us to re-call the
DMA chain over and over again. This leads to, in the BMDMA case,
leaked memory for short PRDTs, and infinite loops and resource
usage in the AHCI case.
The .prepare_buf() callback is reworked to return the number of
bytes that it successfully prepared. 0 is a valid, non-error
answer that means the table was empty and described no bytes.
-1 indicates an error.
Our current implementation uses the io_buffer in IDEState to
ultimately describe the size of a prepared scatter-gather list.
Even though the AHCI PRDT/SGList can be as large as 256GiB, the
AHCI command header limits transactions to just 4GiB. ATA8-ACS3,
however, defines the largest transaction to be an LBA48 command
that transfers 65,536 sectors. With a 512 byte sector size, this
is just 32MiB.
Since our current state structures use the int type to describe
the size of the buffer, and this state is migrated as int32, we
are limited to describing 2GiB buffer sizes unless we change the
migration protocol.
For this reason, this patch begins to unify the assertions in the
IDE pathways that the scatter-gather list provided by either the
AHCI PRDT or the PCI BMDMA PRDs can only describe, at a maximum,
2GiB. This should be resilient enough unless we need a sector
size that exceeds 32KiB.
Further, the likelihood of any guest operating system actually
attempting to transfer this much data in a single operation is
very slim.
To this end, the IDEState variables have been updated to more
explicitly clarify our maximum supported size. Callers to the
prepare_buf callback have been reworked to understand the new
return code, and all versions of the prepare_buf callback have
been adjusted accordingly.
Lastly, the ahci_populate_sglist helper, relied upon by the
AHCI implementation of .prepare_buf() as well as the PCI
implementation of the callback have had overflow assertions
added to help make clear the reasonings behind the various
type changes.
[Added %d -> %"PRId64" fix John sent because off_pos changed from int to
int64_t.
--Stefan]
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1414785819-26209-4-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The intent of this patch is to further unify the creation and
deletion of the sglist used for all AHCI transfers, including
emulated PIO, ATAPI R/W, and native DMA R/W.
By replacing ahci_start_transfer's call to ahci_populate_sglist
with ahci_dma_prepare_buf, we reduce the number of direct calls
where we manipulate the scatter-gather list in the AHCI code.
To make this switch, the constant "0" passed as an offset
in ahci_dma_prepare_buf is adjusted to use io_buffer_offset.
For DMA pathways, this has no effect: io_buffer_offset is always
updated to 0 at the beginning of a DMA transfer loop regardless.
DMA pathways through ide_dma_cb() update the io_buffer_offset
accordingly, and for circumstances where we might make several
trips through this loop, this may actually correct a design flaw.
For PIO pathways, the newly updated ahci_dma_prepare_buf will
now prepare the sglist at the correct offset. It will also set
io_buffer_size, but this is not used in the cmd_read_pio or
cmd_write_pio pathways.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1414785819-26209-3-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Currently, for emulated PIO transfers through the AHCI device,
any attempt made to request more than a single sector's worth
of data will result in the same sector being transferred over
and over.
For example, if we request 8 sectors via PIO READ SECTORS, the
AHCI device will give us the same sector eight times.
This patch adds offset tracking into the PIO pathways so that
we can fulfill these requests appropriately.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1414785819-26209-2-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This patch fixes a regression caused by commit
659142ecf7.
The problem occurs when we wish to return early
from the ahci_start_transfer function, but are now
updating the transferred byte count in the AHCI
command header via ahci_commit_buf.
This will cause problems in the Windows 8 installer.
Don't update the byte count in the command header
for the transmission of ATAPI packets: These commands
will distort the final byte count of the actual data
payload.
The call to ahci_commit_buf remains in the "out"
portion of the call in order to clean up the sglist.
The byte count is maintained by forcing size to be 0.
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The SDB FIS creation was mangled;
We were writing the error byte to byte 0,
and omitting the SDB FIS magic byte.
Though the SDB packet layout states that:
byte 0: Must be 0xA1 to indicate SDB FIS.
byte 1: Port multiplier select & other flags
byte 2: status byte.
byte 3: error byte.
This patch adds an SDB FIS structure with
human-readable names, and ensures that we
are filling the structure appropriately.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Tested-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 1412204151-18117-7-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Currently, DMA read/write operations neglect to update
the byte count after a successful transfer like ATAPI
DMA read or PIO read/write operations do.
We correct this oversight by adding another callback into
the IDEDMAOps structure. The commit callback is called
whenever we are cleaning up a scatter-gather list.
AHCI can register this callback in order to update post-
transfer information such as byte count updates.
We use this callback in AHCI to consolidate where we delete
the SGlist as generated from the PRDT, as well as update the
byte count after the transfer is complete.
The QEMUSGList structure has an init flag added to it in order
to make qemu_sglist_destroy a nop if it is called when
there is no sglist, which simplifies cleanup and error paths.
This patch fixes several AHCI problems, notably Non-NCQ modes
of operation for Windows 7 as well as Hibernate support for Windows 7.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Tested-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 1412204151-18117-3-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Currently, the D2H FIS packets AHCI generates simply parrot back
the LBA that the guest sent to us in the cmd_fis. However, some
commands (like READ NATIVE MAX) modify the LBA registers as a
return value, through which the AHCI D2H FIS is the only response
mechanism. Thus, the D2H response should use the current register
values, not the initial ones.
This patch adjusts the LBA and drive select register responses for
PIO Setup and D2H FIS response packets.
Additionally, the PIO and D2H FIS responses copy too many bytes
from the command FIS that it is being generated from. Specifically,
byte 11 which is the Features(15:8) field for Register Host to
Device FIS packets, is instead reserved for the PIO Setup FIS and
should always be 0.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Tested-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 1412204151-18117-2-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Device models should access their block backends only through the
block-backend.h API. Convert them, and drop direct includes of
inappropriate headers.
Just four uses of BlockDriverState are left:
* The Xen paravirtual block device backend (xen_disk.c) opens images
itself when set up via xenbus, bypassing blockdev.c. I figure it
should go through qmp_blockdev_add() instead.
* Device model "usb-storage" prompts for keys. No other device model
does, and this one probably shouldn't do it, either.
* ide_issue_trim_cb() uses bdrv_aio_discard() instead of
blk_aio_discard() because it fishes its backend out of a BlockAIOCB,
which has only the BlockDriverState.
* PC87312State has an unused BlockDriverState[] member.
The next two commits take care of the latter two.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
I'll use it with block backends shortly, and the name is going to fit
badly there. It's a block layer thing anyway, not just a block driver
thing.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This patch implements the backend for the Q35 board
for us to be able to pick up and use drives defined
by the -cdrom, -hda, or -drive if=ide shorthand options.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 1412187569-23452-7-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
In a real AHCI device, several S/ATA registers are mirrored or shadowed
within the AHCI register set. These registers are not updated
synchronously for each read access, but are instead updated after a
Device-to-Host Register FIS packet is received. The D2H FIS contains
the values from these registers on the device.
In QEMU, by reaching directly into the device to grab these bits before
they are "sent," we may introduce race conditions where unexpected
values are present "before they are sent" which could cause issues for
some guests, particularly if an attempt is made to read the PxTFD
register prior to enabling the port, where incorrect values will be read.
This patch also addresses the boot-time values for the PxTFD and PxSIG
registers to bring them in line with the AHCI 1.3 specification.
Lastly, several fields (PxTFD, PxSIG and PxSACT) are read-only,
and any attempts to write to them should be ignored.
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1408643079-30675-6-git-send-email-jsnow@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Before, bdrv_aio_cancel will either complete the request (like normal)
and call CB with an actual return code, or skip calling the request (for
example when the IO req is not submitted by thread pool yet).
We will change bdrv_aio_cancel to do it differently: always call CB
before return, with either [1] a normal req completion ret code, or [2]
ret == -ECANCELED. So the callers' callback must accept both cases. The
existing logic works with case [1], but not [2].
The simplest transition of callback code is do nothing in case [2], just
as if the CB is not called by the bdrv_aio_cancel() call.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
This is the next step for decoupling block accounting functions from
BlockDriverState.
In a future commit the BlockAcctStats structure will be moved from
BlockDriverState to the device models structures.
Note that bdrv_get_stats was introduced so device models can retrieve the
BlockAcctStats structure of a BlockDriverState without being aware of it's
layout.
This function should go away when BlockAcctStats will be embedded in the device
models structures.
CC: Kevin Wolf <kwolf@redhat.com>
CC: Stefan Hajnoczi <stefanha@redhat.com>
CC: Keith Busch <keith.busch@intel.com>
CC: Anthony Liguori <aliguori@amazon.com>
CC: "Michael S. Tsirkin" <mst@redhat.com>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Eric Blake <eblake@redhat.com>
CC: Peter Maydell <peter.maydell@linaro.org>
CC: Michael Tokarev <mjt@tls.msk.ru>
CC: John Snow <jsnow@redhat.com>
CC: Markus Armbruster <armbru@redhat.com>
CC: Alexander Graf <agraf@suse.de>
CC: Max Reitz <mreitz@redhat.com>
Signed-off-by: Benoît Canet <benoit.canet@nodalink.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The middle term goal is to move the BlockAcctStats structure in the device models.
(Capturing I/O accounting statistics in the device models is good for billing)
This patch make a small step in this direction by removing a reference to BDRV.
CC: Kevin Wolf <kwolf@redhat.com>
CC: Stefan Hajnoczi <stefanha@redhat.com>
CC: Keith Busch <keith.busch@intel.com>
CC: Anthony Liguori <aliguori@amazon.com>
CC: "Michael S. Tsirkin" <mst@redhat.com>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: John Snow <jsnow@redhat.com>
CC: Richard Henderson <rth@twiddle.net>
CC: Markus Armbruster <armbru@redhat.com>
CC: Alexander Graf <agraf@suse.de>i
Signed-off-by: Benoît Canet <benoit.canet@nodalink.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
g_new(T, n) is neater than g_malloc(sizeof(T) * n). It's also safer,
for two reasons. One, it catches multiplication overflowing size_t.
Two, it returns T * rather than void *, which lets the compiler catch
more type errors.
Patch created with Coccinelle, with two manual changes on top:
* Add const to bdrv_iterate_format() to keep the types straight
* Convert the allocation in bdrv_drop_intermediate(), which Coccinelle
inexplicably misses
Coccinelle semantic patch:
@@
type T;
@@
-g_malloc(sizeof(T))
+g_new(T, 1)
@@
type T;
@@
-g_try_malloc(sizeof(T))
+g_try_new(T, 1)
@@
type T;
@@
-g_malloc0(sizeof(T))
+g_new0(T, 1)
@@
type T;
@@
-g_try_malloc0(sizeof(T))
+g_try_new0(T, 1)
@@
type T;
expression n;
@@
-g_malloc(sizeof(T) * (n))
+g_new(T, n)
@@
type T;
expression n;
@@
-g_try_malloc(sizeof(T) * (n))
+g_try_new(T, n)
@@
type T;
expression n;
@@
-g_malloc0(sizeof(T) * (n))
+g_new0(T, n)
@@
type T;
expression n;
@@
-g_try_malloc0(sizeof(T) * (n))
+g_try_new0(T, n)
@@
type T;
expression p, n;
@@
-g_realloc(p, sizeof(T) * (n))
+g_renew(T, p, n)
@@
type T;
expression p, n;
@@
-g_try_realloc(p, sizeof(T) * (n))
+g_try_renew(T, p, n)
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Memory changes for QOMification and automatic tracking of MR lifetime.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=M+/m
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging
SCSI changes that enable sending vendor-specific commands via virtio-scsi.
Memory changes for QOMification and automatic tracking of MR lifetime.
# gpg: Signature made Mon 18 Aug 2014 13:03:09 BST using RSA key ID 9B4D86F2
# gpg: Good signature from "Paolo Bonzini <pbonzini@redhat.com>"
# gpg: aka "Paolo Bonzini <bonzini@gnu.org>"
* remotes/bonzini/tags/for-upstream:
mtree: remove write-only field
memory: Use canonical path component as the name
memory: Use memory_region_name for name access
memory: constify memory_region_name
exec: Abstract away ref to memory region names
loader: Abstract away ref to memory region names
tpm_tis: remove instance_finalize callback
memory: remove memory_region_destroy
memory: convert memory_region_destroy to object_unparent
ioport: split deletion and destruction
nic: do not destroy memory regions in cleanup functions
vga: do not dynamically allocate chain4_alias
sysbus: remove unused function sysbus_del_io
qom: object: move unparenting to the child property's release callback
qom: object: delete properties before calling instance_finalize
virtio-scsi: implement parse_cdb
scsi-block, scsi-generic: implement parse_cdb
scsi-block: extract scsi_block_is_passthrough
scsi-bus: introduce parse_cdb in SCSIDeviceClass and SCSIBusInfo
scsi-bus: prepare scsi_req_new for introduction of parse_cdb
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The function is empty after the previous patch, so remove it.
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
PIO commands should put a PIO Setup FIS in the receive area when data
transfer ends. Currently QEMU does not do this and only places the
D2H FIS at the end of the operation.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
AHCI has code to fill in the D2H FIS trigger the IRQ all over the place.
Centralize this in a single cmd_done callback by generalizing the existing
async_cmd_done callback.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
These are defined twice, just use one set consistently.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
It is now called only after the set_inactive callback. Put the two together.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Similar to the case removed in commit 69c38b8 (ide/core: Remove explicit
setting of BM_STATUS_INT, 2011-05-19), the only remaining use of
add_status(..., BM_STATUS_INT) is for short PRDs. The flag should
not be raised in this case.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Drop the unused return value and make the callback optional.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Drop the unused return value.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Drop the unused return value and make the callback optional.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Drop the unused return value and make the callback optional.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
In map_page() in hw/ide/ahci.c, replace cpu_physical_memory_map() and
cpu_physical_memory_unmap() with dma_memory_map() and dma_memory_unmap(),
because ahci devices should not access memory directly but via their address
space. Add an AddressSpace parameter to map_page(). In order to call
map_page(), we should pass the AHCIState.as as the AddressSpace argument.
Signed-off-by: Le Tan <tamlokveer@gmail.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
The data byte count(DBC) read from the description information is defined for
bits 21:00. Bits 30:22 are reserved and bit 31 is the Interrupt on Completion
(I) flag.
Completion interrupts are triggered after every transaction instead of on
I-flag in QEMU. tbl_entry_size is a signed integer and improperly reading the
DBC leads to a negative offset that causes sglist allocation to fail.
Signed-off-by: Reza Jelveh <reza.jelveh@tuhh.de>
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
After previous Peter patch, they are redundant. This way we don't
assign them except when needed. Once there, there were lots of case
where the ".fields" indentation was wrong:
.fields = (VMStateField []) {
and
.fields = (VMStateField []) {
Change all the combinations to:
.fields = (VMStateField[]){
The biggest problem (appart from aesthetics) was that checkpatch complained
when we copy&pasted the code from one place to another.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Acked-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
CVE-2013-4526
Within hw/ide/ahci.c, VARRAY refers to ports which is also loaded. So
we use the old version of ports to read the array but then allow any
value for ports. This can cause the code to overflow.
There's no reason to migrate ports - it never changes.
So just make sure it matches.
Reported-by: Anthony Liguori <anthony@codemonkey.ws>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Add U suffix to avoid shifting left into the sign bit, which
is undefined behaviour.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Non-PCI AHCI support is broken due to assertion failures when trying
to convert AHCIState to a PCIDevice pointer as AHCIState can have
different container structs. Fix this by using the non-asserting object
cast and checking the returned pointer is not NULL.
The AddressSpace pointer is also being initialized to NULL and causing
dma_memory_map call to fail. Fix this by initializing to
address_space_memory for sysbus instances.
Also correct AHCI_VMSTATE to use the correct container SysbusAHCIState
for sysbus instances.
Signed-off-by: Rob Herring <rob.herring@linaro.org>
Message-id: 1392073373-3295-1-git-send-email-robherring2@gmail.com
[PMM: added linebreaks to fix overlong lines]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When AHCI executes an asynchronous IDE command, it checked DRDY without
checking either DRQ or BSY. This sometimes caused interrupt to be sent
before command is actually completed.
This resulted in a race condition: if guest then managed to access the
device before command has completed, it would hang waiting for an
interrupt.
This was observed with windows 7 guests.
To fix, check for DRQ or BSY in additiona to DRDY, if set,
the command is asynchronous so delay the interrupt until
asynchronous done callback is invoked.
Reported-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
ATM we set AHCI mode on 1st GHC write.
Spec says we should set it on reset.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The category will be used to sort the devices displayed in
the command line help.
Signed-off-by: Marcel Apfelbaum <marcel.a@redhat.com>
Message-id: 1375107465-25767-4-git-send-email-marcel.a@redhat.com
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Introduce type constant and avoid DO_UPCAST().
Signed-off-by: Hu Tao <hutao@cn.fujitsu.com>
[AF: Renamed parent field]
Signed-off-by: Andreas Färber <afaerber@suse.de>
Replace direct uses of AHCIPCIState::card with QOM casts and rename it
to parent_obj.
Acked-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
AHCI couldn't cope with asynchronous commands that aren't doing DMA, it
simply wouldn't complete them. Due to the bug fixed in commit f68ec837,
FLUSH commands would seem to have completed immediately even if they
were still running on the host. After the commit, they would simply hang
and never unset the BSY bit, rendering AHCI unusable on any OS sending
flushes.
This patch adds another callback for the completion of asynchronous
commands. This is what AHCI really wants to use for its command
completion logic rather than an DMA completion callback.
Cc: qemu-stable@nongnu.org
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
The DMAContext is a simple pointer to an AddressSpace that is now always
already available. Make everyone hold the address space directly,
and clean up the DMA API to use the AddressSpace directly.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
An IDE bus provided by AHCI can only take a single IDE drive. If you add
a drive as slave, qemu used to accept the command line but the device
wouldn't be actually usable. Catch the situation instead and error out.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Headers in include/exec/ are for the deepest innards of QEMU,
they should almost never be included directly.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Many of these should be cleaned up with proper qdev-/QOM-ification.
Right now there are many catch-all headers in include/hw/ARCH depending
on cpu.h, and this makes it necessary to compile these files per-target.
However, fixing this does not belong in these patches.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Jason tested these patches by migrating Windows 7 and Fedora 17 guests
(while under I/O) on both piix with ahci attached and on q35 (which has
a built-in AHCI controller).
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The size of an int depends on the host, so in order to be able to
migrate these fields, make them either int32_t or bool, depending on the
use.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
'dma_status' and 'dma_cb' are written to, but never read.
Remove these fields in preparation for AHCI migration bits.
Signed-off-by: Jason Baron <jbaron@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Since 39bffca203 (qdev: register all
types natively through QEMU Object Model), TypeInfo as used in
the common, non-iterative pattern is no longer amended with information
and should therefore be const.
Fix the documented QOM examples:
sed -i 's/static TypeInfo/static const TypeInfo/g' include/qom/object.h
Since frequently the wrong examples are being copied by contributors of
new devices, fix all types in the tree:
sed -i 's/^static TypeInfo/static const TypeInfo/g' */*.c
sed -i 's/^static TypeInfo/static const TypeInfo/g' */*/*.c
This also avoids to piggy-back these changes onto real functional
changes or other refactorings.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
target_phys_addr_t is unwieldly, violates the C standard (_t suffixes are
reserved) and its purpose doesn't match the name (most target_phys_addr_t
addresses are not target specific). Replace it with a finger-friendly,
standards conformant hwaddr.
Outstanding patchsets can be fixed up with the command
git rebase -i --exec 'find -name "*.[ch]"
| xargs s/target_phys_addr_t/hwaddr/g' origin
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
While testing q35, I found that windows 7 (specifically, windows 7 ultimate
with sp1 x64), wouldn't install because it can't find the cdrom or disk drive.
The failure message is: 'A required cd/dvd device driver is missing. If you
have a driver floppy disk, CD, DVD, or USB flash drive, please insert it now.'
This can also be reproduced on piix by adding an ahci controller, and
observing that windows 7 does not see any devices behind it.
The problem is that when windows issues a HBA reset, qemu does not reset the
individual ports' PxCMD register. Windows 7 then reads back the PxCMD register
and presumably assumes that the ahci controller has already been initialized.
Windows then never sets up the PxIE register to enable interrupts, and thus it
never gets irqs back when it sends ata device inquiry commands.
This change brings qemu into ahci 1.3 specification compliance.
Section 10.4.3 HBA Reset:
"
When GHC.HR is set to '1', GHC.AE, GHC.IE, the IS register, and all port
register fields (except PxFB/PxFBU/PxCLB/PxCLBU) that are not HwInit in the
HBA's register memory space are reset.
"
I've also re-tested Fedora 16 and 17 to verify that they continue to work with
this change.
Signed-off-by: Jason Baron <jbaron@redhat.com>
Acked-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
I noticed that in hw/ide/ahci:ahci_dma_rw_buf() we do not free the sglist. Thus,
I've added a call to qemu_sglist_destroy() to fix this memory leak.
In addition, I've adeed a call in qemu_sglist_destroy() to 0 all of the sglist
fields, in case there is some other codepath that tries to free the sglist.
Signed-off-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
While testing q35, which has its cdrom attached to the ahci controller, I found
that the Fedora 17 install would panic on boot. The panic occurs while
squashfs is trying to read from the cdrom. The errors are:
[ 8.622711] SQUASHFS error: xz_dec_run error, data probably corrupt
[ 8.625180] SQUASHFS error: squashfs_read_data failed to read block
0x20be48a
I was also able to produce corrupt data reads using an installed piix based
qemu machine, using 'dd'. I found that the corruptions were only occuring when
then read size was greater than 128k. For example, the following command
results in corrupted reads:
dd if=/dev/sr0 of=/tmp/blah bs=256k iflag=direct
The > 128k size reads exercise a different code path than 128k and below. In
ide_atapi_cmd_read_dma_cb() s->io_buffer_size is capped at 128k. Thus,
ide_atapi_cmd_read_dma_cb() is called a second time when the read is > 128k.
However, ahci_dma_rw_buf() restart the read from offset 0, instead of at 128k.
Thus, resulting in a corrupted read.
To fix this, I've introduced 'io_buffer_offset' field in IDEState to keep
track of the offset. I've also modified ahci_populate_sglist() to take a new
3rd offset argument, so that the sglist is property initialized.
I've tested this patch using 'dd' testing, and Fedora 17 now correctly boots
and installs on q35 with the cdrom ahci controller.
Signed-off-by: Jason Baron <jbaron@redhat.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The AHCI device can provide both PCI and SysBus AHCI device
emulations. For this reason, it wasn't previously converted to use
the pci_dma_*() helper functions. Now that we have universal DMA
helper functions, this converts AHCI to use them.
The DMAContext is obtained from pci_dma_context() in the PCI case and
set to NULL in the SysBus case (i.e. we assume for now that a SysBus
AHCI has no IOMMU translation).
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
dma-helpers.c contains a number of helper functions for doing
scatter/gather DMA, and various block device related DMA. Currently,
these directly access guest memory using cpu_physical_memory_*(),
assuming no IOMMU translation.
This patch updates this code to use the new universal DMA helper
functions. qemu_sglist_init() now takes a DMAContext * to describe
the DMA address space in which the scatter/gather will take place.
We minimally update the callers qemu_sglist_init() to pass NULL
(i.e. no translation, same as current behaviour). Some of those
callers should pass something else in some cases to allow proper IOMMU
translation in future, but that will be fixed in later patches.
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Properly register reset functions via the device class.
CC: Alexander Graf <agraf@suse.de>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
As in the SATA and AHCI specifications, a FIS is 5 Dwords of 4 bytes
each, which comes to 20 bytes (decimal), not 0x20.
Signed-off-by: Daniel Verkamp <daniel@drv.nu>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Most MemoryRegionOps already had the const attribute.
This patch adds it to the remaining ones.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
* kwolf/for-anthony:
AHCI: Masking of IRQs actually masks them
sheepdog: fix co_recv coroutine context
AHCI: Fix port reset race
rewrite QEMU_BUILD_BUG_ON
qcow2: Keep unknown header extension when rewriting header
qcow2: Update whole header at once
vpc: Round up image size during fixed image creation
vpc: Add support for Fixed Disk type
iSCSI: add configuration variables for iSCSI
qemu-io: add write -z option for bdrv_co_write_zeroes
qed: add .bdrv_co_write_zeroes() support
qed: replace is_write with flags field
block: perform zero-detection during copy-on-read
block: add .bdrv_co_write_zeroes() interface
cutils: extract buffer_is_zero() from qemu-img.c
Replace device_init() with generalized type_init().
While at it, unify naming convention: type_init([$prefix_]register_types)
Also, type_init() is a function, so add preceding blank line where
necessary and don't put a semicolon after the closing brace.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Cc: Anthony Liguori <anthony@codemonkey.ws>
Cc: malc <av1474@comtv.ru>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
When masking IRQ lines, we should actually mask them out and not declare
them active anymore. Once we mask them in again, they are allowed to trigger
again.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
bdrv_aio_cancel() can trigger bdrv_aio_flush() which makes all aio
that is currently in flight finish. So what we do is:
port reset
detect ncq in flight
cancel ncq
delete ncq sg list
at which point we have double freed the sg list. Instead, with this
patch we do:
port reset
detect ncq in flight
cancel ncq
check if we are really still in flight
delete ncq sg list
which makes things work and gets rid of the race.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This was done in a mostly automated fashion. I did it in three steps and then
rebased it into a single step which avoids repeatedly touching every file in
the tree.
The first step was a sed-based addition of the parent type to the subclass
registration functions.
The second step was another sed-based removal of subclass registration functions
while also adding virtual functions from the base class into a class_init
function as appropriate.
Finally, a python script was used to convert the DeviceInfo structures and
qdev_register_subclass functions to TypeInfo structures, class_init functions,
and type_register_static calls.
We are almost fully converted to QOM after this commit.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This converts three devices because apic and ioapic are subclasses of sysbus.
Converting subclasses independently of their base class is prohibitively hard.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Add support for ahci on sysbus.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement an I/O space index-data register pair as defined by the AHCI
spec, including the corresponding SATA PCI capability and BAR.
This allows real-mode code to access the AHCI registers; real-mode
code cannot address the memory-mapped register space because it is
beyond the first megabyte.
Signed-off-by: Daniel Verkamp <daniel@drv.nu>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
I've found that FreeBSD AHCI driver doesn't work with AHCI hardware
emulation of QEMU 0.15.0. I believe the problem is on QEMU's side. As I
see, it clears port's Interrupt Enable register each time when reset of
any level happens. Is is reasonable for the global controller reset. It
is probably not good, but acceptable for FreeBSD driver for the port
hard reset. But it is IMO wrong for the device soft reset. None of real
hardware I know behaves that way.
Signed-off-by: Alexander Motin <mav@FreeBSD.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Today, when notifying a VM state change with vm_state_notify(),
we pass a VMSTOP macro as the 'reason' argument. This is not ideal
because the VMSTOP macros tell why qemu stopped and not exactly
what the current VM state is.
One example to demonstrate this problem is that vm_start() calls
vm_state_notify() with reason=0, which turns out to be VMSTOP_USER.
This commit fixes that by replacing the VMSTOP macros with a proper
state type called RunState.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Member variable is_read is written, but never read
(contrary to its name). Remove it.
Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Decouple the I/O accounting from bdrv_aio_readv/writev/flush and
make the hardware models call directly into the accounting helpers.
This means:
- we do not count internal requests from image formats in addition
to guest originating I/O
- we do not double count I/O ops if the device model handles it
chunk wise
- we only account I/O once it actuall is done
- can extent I/O accounting to synchronous or coroutine I/O easily
- implement I/O latency tracking easily (see the next patch)
I've conveted the existing device model callers to the new model,
device models that are using synchronous I/O and weren't accounted
before haven't been updated yet. Also scsi hasn't been converted
to the end-to-end accounting as I want to defer that after the pending
scsi layer overhaul.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
AHCI provides two ways of reading/writing data:
1) NCQ
2) ATA commands with the LBA in the command FIS
In the second code path, we didn't handle any LBAs that were bigger than
16 bits, so whenever a guest that used high LBA numbers wanted to access
data, the LBA got truncated down to 16 bits, giving the guest garbage.
This patch adds support for LBAs higher than 16 bits. I've tested that it
works just fine with SeaBIOS and Linux guests. This patch also unbreaks
the often reported grub errors people have seen with AHCI.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
If ahci_dma_set_inactive is called a while there is still a pending BH
from a previous run, we will crash on the second run of
ahci_check_cmd_bh as it overwrites AHCIDevice::check_bh. Avoid this
broken and redundant duplicate registration.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Different AHCI controllers have a different number of ports, so the core
shouldn't care about the amount of ports available.
This patch makes the number of ports available to the AHCI core runtime
configurable, allowing us to have multiple different AHCI implementations
with different amounts of ports.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The ahci code was missing its soft reset functionality. This wasn't really an
issue for Linux guests, but Windows gets confused when the controller doesn't
reset when it tells it so.
Using this patch I can now successfully boot Windows 7 from AHCI using AHCI
enabled SeaBIOS.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The drive sends a d2h init fis on initialization. Usually, the guest doesn't
receive fises yet at that point though, so the delivery is deferred.
Let's reflect that by sending the init fis on fis receive enablement.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Sebastian's patch already did a pretty good job at splitting up ICH-9
AHCI code and the AHCI core. We need some more though. Copyright was missing,
the lspci dump belongs to ICH-9, we don't need the AHCI core to have its
own qdev device duplicate.
So let's split them a bit more in this patch, making things easier to
read an understand.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
There are multiple ahci devices out there. The currently implemented ich-9
is only one of the many. So let's split that one out into a separate file
to stress the difference.
Signed-off-by: Sebastian Herbszt <herbszt@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Before commit 622b520f, index=12 meant bus=1,unit=5.
Since the commit, it means bus=0,unit=12. The drive is created, but
not the guest device. That's because the controllers we use with
if=scsi drives (lsi53c895a and esp) support only 7 units, and
scsi_bus_legacy_handle_cmdline() ignores drives with unit numbers
exceeding that limit.
Changing the mapping of index to bus, unit is a regression. Breaking
-drive invocations that used to work just makes it worse.
Revert the part of commit 622b520f that causes this, and clean up
some.
Note that the fix only affects if=scsi. You can still put more than 7
units on a SCSI bus with -device & friends.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The len and is_write arguments to cpu_physical_memory_unmap() were
swapped. This patch changes calls to use the correct argument ordering.
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Avoid these warnings with GCC 4.6.0:
/src/qemu/hw/ide/ahci.c: In function 'ahci_reset_port':
/src/qemu/hw/ide/ahci.c:810:14: error: variable 'tfd' set but not used [-Werror=unused-but-set-variable]
/src/qemu/hw/ide/ahci.c: In function 'handle_cmd':
/src/qemu/hw/ide/ahci.c:1103:19: error: variable 'pr' set but not used [-Werror=unused-but-set-variable]
In the tfd variable case, fix the logic also.
CC: Alexander Graf <agraf@suse.de>
CC: Kevin Wolf <kwolf@redhat.com>
Acked-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Set SATA Mode Select to AHCI in the Address Map Register.
Signed-off-by: Sebastian Herbszt <herbszt@gmx.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This patch adds an emulation layer for an ICH-9 AHCI controller. For now
this controller does not do IDE legacy emulation. It is a pure AHCI controller.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
John Snow
Markus Armbruster
Fam Zheng
Benoît Canet
Peter Maydell
Paolo Bonzini
Le Tan
Reza Jelveh
Juan Quintela
Michael S. Tsirkin
Rob Herring
Alexander Graf
Andreas Färber
Marcel Apfelbaum
Hu Tao
Kevin Wolf
Jason Baron
Avi Kivity
David Gibson
Jan Kiszka
Daniel Verkamp
Stefan Weil
Anthony Liguori
Rob Herring
Max Filippov
Alexander Motin
Luiz Capitulino
Stefan Weil
Christoph Hellwig
Sebastian Herbszt
Stefan Hajnoczi
Blue Swirl