Implement an I2C slave which implements DDC and returns the
EDID data for an attached monitor.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Tested-by: Hyun Kwon <hyun.kwon@xilinx.com>
Signed-off-by: KONRAD Frederic <fred.konrad@greensocs.com>
Message-id: 1465833014-21982-7-git-send-email-fred.konrad@greensocs.com
- Rebased on the current master.
- Modified for QOM.
Signed-off-by: KONRAD Frederic <fred.konrad@greensocs.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Tested-By: Hyun Kwon <hyun.kwon@xilinx.com>
[PMM: actually wire up the vmstate to dc->vmsd]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This introduces dpcd module.
It wires on a aux-bus and can be accessed by the driver to get lane-speed, etc.
Signed-off-by: KONRAD Frederic <fred.konrad@greensocs.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Tested-By: Hyun Kwon <hyun.kwon@xilinx.com>
Message-id: 1465833014-21982-6-git-send-email-fred.konrad@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This introduces a new bus: aux-bus.
It contains an address space for aux slaves devices and a bridge to an I2C bus
for I2C through AUX transactions.
Signed-off-by: KONRAD Frederic <fred.konrad@greensocs.com>
Tested-By: Hyun Kwon <hyun.kwon@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1465833014-21982-5-git-send-email-fred.konrad@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch introduces emulation for the Intel 82574 adapter, AKA e1000e.
This implementation is derived from the e1000 emulation code, and
utilizes the TX/RX packet abstractions that were initially developed for
the vmxnet3 device. Although some parts of the introduced code may be
shared with e1000, the differences are substantial enough so that the
only shared resources for the two devices are the definitions in
hw/net/e1000_regs.h.
Similarly to vmxnet3, the new device uses virtio headers for task
offloads (for backends that support virtio extensions). Usage of
virtio headers may be forcibly disabled via a boolean device property
"vnet" (which is enabled by default). In such case task offloads
will be performed in software, in the same way it is done on
backends that do not support virtio headers.
The device code is split into two parts:
1. hw/net/e1000e.c: QEMU-specific code for a network device;
2. hw/net/e1000e_core.[hc]: Device emulation according to the spec.
The new device name is e1000e.
Intel specifications for the 82574 controller are available at:
http://www.intel.com/content/dam/doc/datasheet/82574l-gbe-controller-datasheet.pdf
Throughput measurement results (iperf2):
Fedora 22 guest, TCP, RX
4 ++------------------------------------------+
| |
| X X X X X
3.5 ++ X X X X |
| X |
| |
3 ++ |
G | X |
b | |
/ 2.5 ++ |
s | |
| |
2 ++ |
| |
| |
1.5 X+ |
| |
+ + + + + + + + + + + +
1 ++--+---+---+---+---+---+---+---+---+---+---+
32 64 128 256 512 1 2 4 8 16 32 64
B B B B B KB KB KB KB KB KB KB
Buffer size
Fedora 22 guest, TCP, TX
18 ++-------------------------------------------+
| X |
16 ++ X X X X X
| X |
14 ++ |
| |
12 ++ |
G | X |
b 10 ++ |
/ | |
s 8 ++ |
| |
6 ++ X |
| |
4 ++ |
| X |
2 ++ X |
X + + + + + + + + + + +
0 ++--+---+---+---+---+----+---+---+---+---+---+
32 64 128 256 512 1 2 4 8 16 32 64
B B B B B KB KB KB KB KB KB KB
Buffer size
Fedora 22 guest, UDP, RX
3 ++------------------------------------------+
| X
| |
2.5 ++ |
| |
| |
2 ++ X |
G | |
b | |
/ 1.5 ++ |
s | X |
| |
1 ++ |
| |
| X |
0.5 ++ |
| X |
X + + + + +
0 ++-------+--------+-------+--------+--------+
32 64 128 256 512 1
B B B B B KB
Datagram size
Fedora 22 guest, UDP, TX
1 ++------------------------------------------+
| X
0.9 ++ |
| |
0.8 ++ |
0.7 ++ |
| |
G 0.6 ++ |
b | |
/ 0.5 ++ |
s | X |
0.4 ++ |
| |
0.3 ++ |
0.2 ++ X |
| |
0.1 ++ X |
X X + + + +
0 ++-------+--------+-------+--------+--------+
32 64 128 256 512 1
B B B B B KB
Datagram size
Windows 2012R2 guest, TCP, RX
3.2 ++------------------------------------------+
| X |
3 ++ |
| |
2.8 ++ |
| |
2.6 ++ X |
G | X X X X X
b 2.4 ++ X X |
/ | |
s 2.2 ++ |
| |
2 ++ |
| X X |
1.8 ++ |
| |
1.6 X+ |
+ + + + + + + + + + + +
1.4 ++--+---+---+---+---+---+---+---+---+---+---+
32 64 128 256 512 1 2 4 8 16 32 64
B B B B B KB KB KB KB KB KB KB
Buffer size
Windows 2012R2 guest, TCP, TX
14 ++-------------------------------------------+
| |
| X X
12 ++ |
| |
10 ++ |
| |
G | |
b 8 ++ |
/ | X |
s 6 ++ |
| |
| |
4 ++ X |
| |
2 ++ |
| X X X |
+ X X + + X X + + + + +
0 X+--+---+---+---+---+----+---+---+---+---+---+
32 64 128 256 512 1 2 4 8 16 32 64
B B B B B KB KB KB KB KB KB KB
Buffer size
Windows 2012R2 guest, UDP, RX
1.6 ++------------------------------------------X
| |
1.4 ++ |
| |
1.2 ++ |
| X |
| |
G 1 ++ |
b | |
/ 0.8 ++ |
s | |
0.6 ++ X |
| |
0.4 ++ |
| X |
| |
0.2 ++ X |
X + + + + +
0 ++-------+--------+-------+--------+--------+
32 64 128 256 512 1
B B B B B KB
Datagram size
Windows 2012R2 guest, UDP, TX
0.6 ++------------------------------------------+
| X
| |
0.5 ++ |
| |
| |
0.4 ++ |
G | |
b | |
/ 0.3 ++ X |
s | |
| |
0.2 ++ |
| |
| X |
0.1 ++ |
| X |
X X + + + +
0 ++-------+--------+-------+--------+--------+
32 64 128 256 512 1
B B B B B KB
Datagram size
Signed-off-by: Dmitry Fleytman <dmitry.fleytman@ravellosystems.com>
Signed-off-by: Leonid Bloch <leonid.bloch@ravellosystems.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This will be used by ARM virt machine as a power button.
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1458221140-15232-2-git-send-email-zhaoshenglong@huawei.com
[PMM: Use hyphen rather than underscore in type names;
add a comment briefly describing what the device does]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement ITC as a single object consisting of two memory regions:
1) tag_io: ITC Configuration Tags (i.e. ITCAddressMap{0,1} registers) which
are accessible by the CPU via CACHE instruction. Also adding
MemoryRegion *itc_tag to the CPUMIPSState so that CACHE instruction will
dispatch reads/writes directly.
2) storage_io: memory-mapped ITC Storage whose address space is configurable
(i.e. enabled/remapped/resized) by writing to ITCAddressMap{0,1} registers.
ITC Storage contains FIFO and Semaphore cells. Read-only FIFO bit in the
ITC cell tag indicates the type of the cell. If the ITC Storage contains
both types of cells then FIFOs are located before Semaphores.
Since issuing thread can get blocked on the access to a cell (in E/F
Synchronized and P/V Synchronized Views) each cell has a bitmap to track
which threads are currently blocked.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Implement generic MIPS Coherent Processing System (CPS) which in this
commit just creates VPs, but it will serve as a container also for
other components like Global Configuration Registers and Cluster Power
Controller.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Add mips-softmmu-common.mak and include it in existing mips*-softmmu.mak
files to avoid having to repeat CONFIG defines four times.
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Event notifiers are designed for eventfd(2). They can fall back to
pipes, but according to Paolo, event_notifier_init_fd() really
requires the real thing, and should therefore be under #ifdef
CONFIG_EVENTFD. Do that.
Its only user is ivshmem, which is currently CONFIG_POSIX. Narrow it
to CONFIG_EVENTFD.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1458066895-20632-6-git-send-email-armbru@redhat.com>
Implement basic ASPEED timer functionality for the AST2400 SoC[1]: Up to
8 timers can independently be configured, enabled, reset and disabled.
Some hardware features are not implemented, namely clock value matching
and pulse generation, but the implementation is enough to boot the Linux
kernel configured with aspeed_defconfig.
[1] http://www.aspeedtech.com/products.php?fPath=20&rId=376
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1458096317-25223-2-git-send-email-andrew@aj.id.au
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This adds the SAS1068 device, a SAS disk controller used in VMware that
is oldish but widely supported and has decent performance. Unlike
megasas, it presents itself as a SAS controller and not as a RAID
controller. The device corresponds to the mptsas kernel driver in
Linux.
A few small things in the device setup are based on Don Slutz's old
patch, but the device emulation was written from scratch based on Don's
SeaBIOS patch and on the FreeBSD and Linux drivers. It is 2400 lines
shorter than Don's patch (and roughly the same size as MegaSAS---also
because it doesn't support the similar SPI controller), implements SCSI
task management functions (with asynchronous cancellation), supports
big-endian hosts, has complete support for migration and follows the
QEMU coding standards much more closely.
To write the driver, I first split Don's patch in two parts, with
the configuration bits in one file and the rest in a separate file.
I first left mptconfig.c in place and rewrote the rest, then deleted
mptconfig.c as well. The configuration pages are still based mostly on
VirtualBox's, though not exactly the same. However, the implementation
is completely different. The contents of the pages themselves should
not be copyrightable.
Signed-off-by: Don Slutz <Don@CloudSwitch.com>
Message-Id: <1347382813-5662-1-git-send-email-Don@CloudSwitch.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This adds the system mailboxes which are used to communicate with a
number of GPU peripherals on Pi/Pi2.
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
NFIT is defined in ACPI 6.0: 5.2.25 NVDIMM Firmware Interface Table (NFIT)
Currently, we only support PMEM mode. Each device has 3 structures:
- SPA structure, defines the PMEM region info
- MEM DEV structure, it has the @handle which is used to associate specified
ACPI NVDIMM device we will introduce in later patch.
Also we can happily ignored the memory device's interleave, the real
nvdimm hardware access is hidden behind host
- DCR structure, it defines vendor ID used to associate specified vendor
nvdimm driver. Since we only implement PMEM mode this time, Command
window and Data window are not needed
The NVDIMM functionality is controlled by the parameter, 'nvdimm', which
is introduced for the machine, there is a example to enable it:
-machine pc,nvdimm -m 8G,maxmem=100G,slots=100 -object \
memory-backend-file,id=mem1,share,mem-path=/tmp/nvdimm1,size=10G -device \
nvdimm,memdev=mem1,id=nv1
It is disabled on default
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Introduce "nvdimm" device which is based on pc-dimm device type
Currently, nothing is specific for nvdimm but hotplug is disabled
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This provides the simulation of the BT hardware interface for
IPMI.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This provides the simulation of the KCS hardware interface.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This adds an interface for IPMI that connects to a remote
BMC over a chardev (generally a TCP socket). The OpenIPMI
lanserv simulator describes this interface, see that for
interface details.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This provides a minimal local BMC, basically enough to comply with the
spec and provide a complete watchdog timer (including a sensor, SDR,
and event).
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add the basic IPMI types and infrastructure to QEMU. Low-level
interfaces and simulation interfaces will register with this; it's
kind of the go-between to tie them together.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
'hyperv-testdev' will be used by kvm-unit-tests
to setup Hyper-V SynIC SINT's routing and to inject
Hyper-V SynIC SINT's.
Hyper-V test device is ISA type device that creates 0x3000
IO memory region and catches write access into it. Every
write operation data decoded into ctl code and parameters
for Hyper-V test device.
Signed-off-by: Andrey Smetanin <asmetanin@virtuozzo.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Richard Henderson <rth@twiddle.net>
CC: Eduardo Habkost <ehabkost@redhat.com>
CC: "Andreas Färber" <afaerber@suse.de>
CC: Marcelo Tosatti <mtosatti@redhat.com>
CC: Roman Kagan <rkagan@virtuozzo.com>
CC: Denis V. Lunev <den@openvz.org>
CC: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The uses of the CONFIG_GDBSTUB_XML define were removed in commit
b77abd95a9, but the define in aarch64-linux-user.mak somehow
escaped the cull (the patchset probably crossed in the mail with
the patches adding aarch64 support). Remove the stray define.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Laurent Desnogues <laurent.desnogues@gmail.com>
Message-id: 1447690178-4560-1-git-send-email-peter.maydell@linaro.org
ivshmem doesn't actually require kvm, so enable it when POSIX is
enabled. (it is required however when ioeventfd is enabled)
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
It works fine with the Linux driver out of the box
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
ICC bus impl has been droped, so all icc related files are not useful
any more; delete them.
Signed-off-by: Zhu Guihua <zhugh.fnst@cn.fujitsu.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Initialize a hotplug memory region under which all the hotplugged
memory is accommodated. Also enable memory hotplug by setting
CONFIG_MEM_HOTPLUG.
Modelled on i386 memory hotplug.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Add related configuration and make files for tilegx.
The target can now build, though not run anything.
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <BLU436-SMTP1588E5A03AD5E94B07E988B9660@phx.gbl>
Signed-off-by: Richard Henderson <rth@twiddle.net>
This one just syncs x86_64 and i386.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: qemu-trivial@nongnu.org
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
For now we support the following devices:
* CPU: ARM926
* Interrupt Controller: AVIC
* CCM
* UART x 5
* EPIT x 2
* GPT x 4
* FEC
* I2C x 3
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: 62218bfa90f9101f79098e768c3d58bd92dcb7f3.1441057361.git.jcd@tribudubois.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is based on mcf_fec.c FEC implementation for Coldfire
* A generic PHY was added (borrowwed from LAN9118)
* The buffer management is also modified as buffers are
slightly different between Coldfire and i.MX
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: fb314f8a120aa49f8f6ad886f312c649b484fb5a.1441057361.git.jcd@tribudubois.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The slave mode is not implemented.
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: 508dbf2ebe26ec383d3a12a1db5a7890ac8acf20.1441057361.git.jcd@tribudubois.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
For now we support the following devices:
* CPU: ARM1136
* Interrupt Controller: AVIC
* CCM
* UART x 2
* EPIT x 2
* GPT
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: f146d819594e41568daec42a1d0f440cdfe3df76.1441057361.git.jcd@tribudubois.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch generates smbios tables for ARM mach-virt. Also add
CONFIG_SMBIOS=y for ARM default config.
Acked-by: Gabriel Somlo <somlo@cmu.edu>
Tested-by: Gabriel Somlo <somlo@cmu.edu>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Tested-by: Leif Lindholm <leif.lindholm@linaro.org>
Signed-off-by: Wei Huang <wei@redhat.com>
Message-id: 1440615870-9518-3-git-send-email-wei@redhat.com
[PMM: Added missing braces around an if().]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
To share smbios among different architectures, this patch moves SMBIOS
code (smbios.c and smbios.h) from x86 specific folders into new
hw/smbios directories. As a result, CONFIG_SMBIOS=y is defined in
x86 default config files.
Acked-by: Gabriel Somlo <somlo@cmu.edu>
Tested-by: Gabriel Somlo <somlo@cmu.edu>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Tested-by: Leif Lindholm <leif.lindholm@linaro.org>
Signed-off-by: Wei Huang <wei@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
MIPS doesn't need it, and including it creates problem as we are adding
dependency on ISA LPC bridge.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch adds a virtio-vga device. It is simliar to virtio-gpu-pci,
but it also adds in vga compatibility, so guests without native
virtio-gpu support can drive the device in vga mode. It is compatible
with stdvga.
Written by Dave Airlie and Gerd Hoffmann.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This patch introduces a new diag288 watchdog device that will, just like
other watchdogs, monitor a guest and take corresponding actions when it
detects that the guest is not responding.
diag288 is s390x specific. The wiring to s390x KVM will be done in
separate patches.
Signed-off-by: Xu Wang <gesaint@linux.vnet.ibm.com>
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
[split out qemu-option.hx base changes]
Remove now useless device models from other MIPS configurations
We're now compiling 12 files less than before.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
As core.c, piix4.c, ich9.c and pcihp.c are for x86, add CONFIG_ACPI_X86
to make it only for x86. ARM doesn't support cpu and memory hotplug, add
CONFIG_ACPI_CPU_HOTPLUG and CONFIG_ACPI_MEMORY_HOTPLUG to exclude them
for target-arm.
Signed-off-by: Shannon Zhao <zhaoshenglong@huawei.com>
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1432522520-8068-24-git-send-email-zhaoshenglong@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
With quad Cortex-A53 CPUs.
Use SMC PSCI, with the standard policy of secondaries starting in
power-off.
Tested-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: a16202a6c7b79e446e5289d38cb18d2ee4b897a0.1431381507.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Rocker is a simulated ethernet switch device. The device supports up to 62
front-panel ports and supports L2 switching and L3 routing functions, as well
as L2/L3/L4 ACLs. The device presents a single PCI device for each switch,
with a memory-mapped register space for device driver access.
Rocker device is invoked with -device, for example a 4-port switch:
-device rocker,name=sw1,len-ports=4,ports[0]=dev0,ports[1]=dev1, \
ports[2]=dev2,ports[3]=dev3
Each port is a netdev and can be paired with using -netdev id=<port name>.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David Ahern <dsahern@gmail.com>
Message-id: 1426306173-24884-7-git-send-email-sfeldma@gmail.com
rocker: fix clang compiler errors
Consolidate all forward typedef declarations to rocker.h.
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
rocker: add support for flow modification
We had support for flow add/del. This adds support for flow mod. I needed
this for L3 support where an existing route is modified using NLM_F_REPLACE.
For example:
ip route add 12.0.0.0/30 nexthop via 11.0.0.1 dev swp1
ip route change 12.0.0.0/30 nexthop via 11.0.0.9 dev swp2
The first cmd adds the route. The second cmd changes the existing route by
changing its nexthop info.
In the device, a mod operation results in the matching flow enty being modified
with the new settings. This is atomic to the device.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Theres no difference in defconfig. Going forward microblazeel should
superset microblaze so use an include.
Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Boards that do not include an USB controller should not provide
USB devices. However, when running "qemu-system-s390x -device help"
for example, there's still a usb-hub, usb-kbd, usb-mouse and
usb-tablet in the list of "supported" devices. Let's fix that
by compiling and linking the USB files only if it is really
necessary.
Signed-off-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
pci.mak includes a lot of devices - and most of them do not make
sense on s390x, like USB controllers or audio cards. These devices
also show up when running "qemu-system-s390x -device help" and thus
could raise the hope for the users that they could use these kind
of devices with qemu-system-s390x. To avoid this confusion, we
should not include pci.mak and rather include the bare minimum
manually instead.
Signed-off-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Acked-by: Frank Blaschka <blaschka@linux.vnet.ibm.com>
Message-Id: <1426169954-6062-1-git-send-email-thuth@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Rename config option from "glx" to "opengl", glx will not be the only
option for opengl in near future. Also switch over to pkg-config for
opengl support detection.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
This patch adds the stm32f205 SoC. This will be used by the
Netduino 2 to create a machine.
Signed-off-by: Alistair Francis <alistair@alistair23.me>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: 48d509747a1ea0d8a7d5480560495e679990f9d2.1424175342.git.alistair@alistair23.me
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch adds the stm32f2xx System Configuration
Controller. This is used to configure what memory is mapped
at address 0 (although that is not supported) as well
as configure how the EXTI interrupts work (also not
supported at the moment).
This device is not required for basic examples, but more
complex systems will require it (as well as the EXTI device)
Signed-off-by: Alistair Francis <alistair@alistair23.me>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: 5d499d7b60b61d5d6dcb310b2e55411b1f53794e.1424175342.git.alistair@alistair23.me
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
